Blocking and delay performance for differential output-ports choosing probability scheme applied optical burst switching network

Differential output-ports choosing probability (DOCP) scheme is a novel traffic outputting model for core router in optical burst switching (OBS) network. In this paper, we provide an analytical model for studying the performance of traffic blocking and delay in DOCP-applied OBS network. We first evaluate blocking probabilities using DOCP and confirm it by simulation. Then, in optical buffer-equipped OBS core router, we consider the average delay time for buffered traffic and the average total traffic queueing length in core router. The knowledge of delay performance is useful for the optical buffer architecture configuration in differential traffic scenario. Several results indicate that, under the same load condition, the blocking probabilities and the delay time will change along with the changeable ports choosing probability and the ratio between different length bursts in the OBS system.     

Performance enhancement of optical burst switched networks

Optical burst switching (OBS) is an optical switching paradigm which offers a good tradeoff between the traditional optical circuit switching (OCS) and optical packet switching (OPS) since it has the relatively easy implementation of the first and the efficient bandwidth utilization of the second. Hence, OBS is a promising technology for the next generation optical Internet. A buffer-less OBS network can be implemented using ordinary optical communication equipment without the need for either wavelength converters or optical memories. In an OBS network, burst-loss performance is a critical concern. In OBS, the data-burst transmission is delayed by an offset time (relative to its burst control packet (BCP), or header) and the burst follows its header without waiting for an acknowledgment for resource reservation. Thus, a burst may be lost at an intermediate node due to contention, which is generally resolved according to the local routing and bandwidth information. The routing table maintained in each OBS node is generally pre-computed and fixed to forward the data bursts. Such a static forwarding feature might have limited efficiency to resolve contentions. Moreover, a burst may be lost and the network may be congested when a network element (e.g., fiber link) fails. In this paper, an efficient integrated scheme based on dynamic routing and burst segmentation has been proposed to improve reliability of data transport and network load balancing in optical burst switched networks. Simulation results demonstrate that the proposed approach reduces effectively blocking probability and hence contention. Further, it provides end-to-end throughput performance also. Hence, it establishes an appropriate tradeoff between loss rate and end-to-end throughput.     

光突发交换中交换矩阵配置时间的影响研究

光突发交换是近几年出现的一种很有前途的交换技术。在光突发交换网络的核心节点中,光交换矩阵是一个关键部件,其配置时间影响到光突发交换网络的性能。这种影响表现在对数据信道可用时间施加了限制。在考虑光交换矩阵配置时间的基础上给出了修正后的LAUC算法,并通过计算机仿真研究了这种配置时间对光突发交换性能的影响。结果表明,光交换矩阵配置时间的增大会导致输出数据信道利用率的降低,进而增大了数据丢失率。     

用于WDM光突发交换网的改进JIT信令协议

提出了一种用WDM光突发交换网的良好时间通信协议(MJIT-SP)该协议结合了光线路交换和光分组交换的优点与用于光突发交换的其他信令协议相似,MJIT-SP的特点也是采用带外控制信号处理来排除核心节点处对光缓存器的需求然而,与其它协议如JIT-SP相比,它能最小化数据源端的建立时间和最大化交叉连接的带宽利用率而且,MJIT-SP还能支持光网络中无连接和面向连接的数据包传递并介绍了MJIT-SP的基本结构并从三个方面分析了它的基本性能,即建立时间、端到端延时和信道占用时间然后,对本协议与JIT-SP的性能进行了比较,结果显示:MJIT-SP不仅优于JIT-SP,而且还克服了JIT-SP的一个缺点,即过长的信道占用时间此外,还给出了MJIT-SP的信令信息,尤其是非常关键的信号与脉座电平差(SETUP)消息MJIT-SP中的SETUP与JIT-SP中的SETUP不同,它需要给出数据包路由和交换所需的信息,包括数据包长度、比特率、SETUP与数据包之间的偏置时间以及数据业务的质量控制系统(QoS)要求等最后讨论了MJIT-SP两种可能的变化并且分析了它们的优缺点.     

A QoS-Guanranteed Scheduling Algorithm with High Throughput for Edge Nodes of Optical Burst Switching Networks

A scheduling algorithm for the edge nodes of optical burst switching (OBS) networks is proposed to guarantee the delay re quirement of services with different CoS (Class of Service) and provide lower burst loss ratio at the same time. The performance of edge nodes based on the proposed algorithm is presented.     

An optimal protection and restoration scheme (OPARS) for optical networks

Protection and restoration are critical network design issues for optical networks since even a single failure for a short duration may result in huge data loss due to the large capacity of optical fibers. However, few studies have been done on these issues for optical burst switching (OBS) networks. Protection and restoration are essential mechanisms for guaranteeing more reliable traffic delivery services. But it is not easy to apply existing mechanisms to optical burst switching (OBS) networks due to its one-way reservation signaling and the statistical burst multiplexing. Thus, to achieve the high transmission performance and reliability simultaneously, unique properties of OBS must be considered in the design of protection scheme. In this paper, an optimal protection and restoration scheme (OPARS) has been introduced that not only optimizes the number of provisioned protection wavelengths adaptively based on the traffic load as well as the quality of service (QoS) requirements of bursts in high speed networks but also minimizes burst loss rates. In addition, the proposed scheme has been used as an efficient contention resolution technique. The simulation results verify that the proposed scheme improve the network resource and channel utilization while guaranteeing the targeted protection reliability and QoS requirements of bursts.     

Effects of the switching time in OPS/OBS networks

In this paper we present an analytical model, which considers the effects of the switching time on the network performance in service differentiated optical packet/burst switching (OPS/OBS) networks. Our results indicate that the switching time must be less than 10 % of the packet/burst duration in order to avoid any significant reductions in the network performance. Furthermore, regarding a network with full wavelength conversion, we show that the benefits of statistical resource sharing are almost non-existent for low priority traffic when the switching time is large.     

An optimal burst assembly approach employing traffic shaping (OBATS) for OBS

Optical burst switching (OBS) aims at combining the strengths of packet and circuit switching and is considered as a promising technology for implementing the next generation optical Internet, required to cope with the rapid growth of Internet traffic and the increased deployment of new services. In this paper, an optimal burst assembly approach employing traffic shaping (OBATS) for OBS networks has been proposed in order to improve network performance in terms of reduced blocking probability, congestion control and better utilization of bandwidth. Particularly, the proposed scheme aims at reducing the average delay experienced by the packets during the burstification process in optical burst switched (OBS) networks, for a given average size of the bursts produced. Reducing the packet burstification delay, for a given average burst size, is essential for real-time applications; correspondingly, increasing the average burst size for a given packet burstification delay is important for reducing the number of bursts injected into the network and the associated overhead imposed on the core nodes. Simulation results show that the proposed burst assembly approach gives better network performance in terms of burst drop, resource contention and delay as compared to conventional burst assembly approaches.     

A segmentation based channel scheduling scheme for improving channel utilization in OBS networks

Channel scheduling is an important aspect in optical burst switching (OBS) networks. OBS is a promising solution for the future Internet backbone. In OBS network a key issue is data channel scheduling. In this paper we propose a channel scheduling scheme to optimize channel utilization for OBS networks with segmentation. In this paper, we propose an efficient way to organize the void intervals. The channel scheduling method is compared with existing scheduling schemes. Simulation results show that both channel utilization and burst loss ratio performance improved as compared to existing scheduling schemes.     

光突发与光电路混合交换边缘节点的设计与实现

提出了一种将光电路交换和光突发交换融合于同一网络的边缘节点设计方案.根据此方案，网络边缘节点能根据业务需求灵活选择交换方式.该方案在实际实验系统中进行了验证.结果表明，采用光电路交换方式，网络传输速率相对较快，而采用光突发交换方式，网络的带宽利用率更好.这两种交换方式共存于同一网络,一定程度上能提高网络的灵活性和适应性.     

An efficient fault localization or detection mechanism for high speed optical networks

Optical burst switching (OBS) has been considered as the gate through which the envisaged world of optical Internet will be conquered by implementing Internet Protocol (IP) software directly over a wavelength-division-multiplexing (WDM) optical layer (IP/WDM). The main feature for designing next generation optical networks is protecting and restoring high capacity WDM networks from the failures. Quick detection, identification and restoration make networks more strong and consistent even though the failures cannot be avoided. Hence, it is necessary to develop fast, efficient and dependable fault localization or detection mechanisms. In this paper, an efficient scheme for OBS networks has been proposed to provide fast restoration of links with minimum delay as well as blocking probability. By simulation results, it is shown that the proposed OBS scheme achieve less blocking probability and delay while getting higher throughput in comparison to conventional schemes.     

Congestion prevention for reliable OBS

It is known that Internet traffic exhibits a structural self-similarity over a wide range of time scales. Existing performance evaluation studies in optical burst switching (OBS) networks show high contention performance degradation in the nodes under correlated traffic. Due to its buffer-less nature, OBS efficiency can be reduced by resource contention leading to burst loss. Several methods have been proposed to address this problem, most of them relying on reactive mechanisms, which increase the complexity of core nodes, hampering scalability. In this paper to have congestion prevention, an efficient scheme incorporating delayed reservation decision has been proposed which not only offers reduction in resource contention by maintaining the same node complexity as that in general OBS networks with optical buffers but also provides improvement in system's throughput. Simulations show the proposed scheme has better performance than existing schemes in terms of burst loss probability.     

Performance analysis of an improved burst-outputted scheme in a limited buffer equipped OBS core node

Burst-outputted performance will be affected by the outputting scheme in optical burst switching (OBS) core nodes. In this paper, we have evaluated the performance of an improved burst-outputted scheme in an OBS core node, in which fiber delay lines (FDLs) based limited optical buffer has been equipped. Different from the previous works which only consider the same probability to select output-port for burst, the proposed scheme gives a burst-outputted process based on different port selected probability. Simulation results have indicated that, performance evaluation parameters are changed with the output-port selected probability and the different number of FDLs in an optical buffer.     

Hybrid OCS/OBS interconnect in intra-data-center network

We report on a data center network(DCN) architecture based on hybrid optical circuit switching(OCS) and optical burst switching(OBS) interconnect for dynamic DCN connectivity provisioning. With the combination of the centralized and distributed control of the software-defined optical networks, the proposed interconnect can achieve unprecedented flexibility in dealing with both mice and elephant flow in the DCN. Numerical simulation is employed to investigate the performance of the proposed architecture. The results show that the OBS module has preferable performance in dealing with a larger burst packet, and the throughput is constrained by the capacity of the server random access memory module.     

A novel scheme based on minimum delay at the edges for optical burst switching networks

This paper proposes a novel scheme based on minimum delay at the edges (MDE) for optical burst switching (OBS) networks. This scheme is designed to overcome the long delay at the edge nodes of OBS networks. The MDE scheme features simultaneous burst assembly, channel scheduling, and pre-transmission of control packet. It also features estimated setup and explicit release (ESXR) signaling protocol. The MDE scheme can minimize the delay at the edge nodes for data packets, and improve the end-to-end latency performance for OBS networks. In addition, comparing with the conventional scheme, the performances of the MDE scheme are analyzed in this paper.     

光突发交换网络试验平台

研究并实现了几种光突发交换网络的关键技术,包括高速的突发组装技术、突发调度技术及突发光发射及接收技术等,其中突发接收具有较高的灵敏度和小于80 ns的时钟数据恢复时间.在这些技术的基础上,建立了一个灵活且可扩展的光突发交换网络实验平台.在OBS网络平台上进行了TCP性能评估实验和多QoS业务传输实验。实验结果表明光突发网络中丢包率严重影响其上TCP的性能,但若丢包率小于0.1%,则TCP性能可得到一定程度的保证.光突发交换网络实验平台上的TCP传输实验还表明了OBS物理层带来的额外延时对上层TCP带宽有极大的影响.实验结果还验证了OBS网络中的QoS保证机制.     

Impairment-aware QoS provisioning in dual-header OBS networks

Signal degradation due to physical impairments may result in unacceptable bit-error rates of received signals at the destination. Based on earlier work, we study the impairment-aware quality of service (QoS) provisioning problem in dual-header optical burst switching (OBS) networks that employ two control packets for each data burst. At an OBS node, the proposed algorithm schedule bursts for transmission by searching for available resources using admission control and preemption. The algorithm also verifies signal quality. Simulation results show that this algorithm is effective in providing QoS support in OBS networks while considering physical impairment effects.     

A novel optical burst switching architecture for high speed networks

A novel optical burst switching （OBS） high speed network architecture has been proposed. To verify its feasibility and evaluate its performance, just-enough-time （JET） signaling has been considered as a high performance protocol. In the proposed architecture, to avoid burst losses, firstly, a short-prior- confirmation-packet （SPCP） is sent over the control channel that simulates the events that the actual packet will experience. Once SPCP detects a drop at any of the intermediate nodes, the actual packet is not sent but the process repeats. In order to increase network utilization, cost effectiveness and to overcome some limitations of conventional OBS, inherent codes （e.g., orthogonal optical codes （OOC））, which are codified only in intensity, has been used. Through simulations, it shows that a decrease in burst loss probability, cost effectiveness and a gain in processing time are obtained when optical label processing is used as compared with electronic processing.     

United assembly algorithm for optical burst switching

Optical burst switching (OBS) is a promising optical switching technology. The burst assembly algorithm controls burst assembly, which significantly impacts performance of OBS network. This paper provides a new assembly algorithm, united assembly algorithm, which has more practicability than conventional algorithms. In addition, some factors impacting selections of parameters of this algorithm are discussed and the performance of this algorithm is studied by computer simulation.     

Performance analysis of an improved burst-outputted model for an OBS core router

Differentiated probability outputted scheme (DPOS) is an improved burst-outputted paradigm in optical burst switching (OBS) core routers. In this paper, the blocking performance for multi-priority traffic in a DPOS applied OBS core router with limited buffers has been analyzed and discussed firstly. Several simulation results indicted that DPOS had a better performance in blocking than the outputted model presented in the previous work had. Besides, our proposed scheduling mechanism can supported the quality-of-service (QoS) efficiently for OBS networks.