High work function of Al-doped zinc-oxide thin films as transparent conductive anodes in organic light-emitting devices

Deposition of Al-doped ZnO (AZO) films with various film thicknesses on glass substrates was performed to investigate the feasibility of using AZO films as anode electrodes in organic light-emitting devices (OLEDs). The electrical resistivity of the AZO films with a 180-nm thickness was 4.085 × 10⁻² Ω cm, and the average optical transmittance in the visible range was 80.2%. The surface work function for the AZO films, determined from the secondary electron emission coefficients obtained with a focused ion beam, was as high as 4.62 eV. These results indicate that AZO films grown on glass substrates hold promise for potential applications as anode electrodes in high-efficiency OLEDs.     

Optimization of F-doped SnO2 electrodes for organic photovoltaic devices

Fluorine-doped tin oxide (FTO) thin films have been investigated as an alternative to indium tin oxide anodes in organic photovoltaic devices. The structural, electrical, and optical properties of the FTO films grown by pulsed laser deposition were studied as a function of oxygen deposition pressure. For 400 nm thick FTO films deposited at 300°C and 6.7 Pa of oxygen, an electrical resistivity of 5×10⁻⁴ Ω-cm, sheet resistance of 12.5 Ω/□, average transmittance of 87% in the visible range, and optical band gap of 4.25 eV were obtained. Organic photovoltaic (OPV) cells based on poly(3-hexylthiophene)/[6,6]-phenyl-C₆₁-butyric acid methyl ester bulk heterojunctions were prepared on FTO/glass electrodes and the device performance was investigated as a function of FTO film thickness. OPV cells fabricated on the optimum FTO anodes (∼300–600 nm thick) exhibited power conversion efficiencies of ∼3%, which is comparable to the same device made on commercial ITO/glass electrodes (3.4%).     

Optimization of the optical and electrical properties of electron beam evaporated aluminum-doped zinc oxide films for opto-electronic applications

Aluminum-doped zinc oxide (AZO) thin films have been deposited by electron beam evaporation technique on glass substrates. The structural, electrical and optical properties of AZO films have been investigated as a function of annealing temperature. It was observed that the optical properties such as transmittance, reflectance, optical band gap and refractive index of AZO films were strongly affected by annealing temperature. The transmittance values of 84% in the visible region and 97% in the NIR region were obtained for AZO film annealed at 475 °C. The room temperature electrical resistivity of 4.6×10⁻³ Ω cm has been obtained at the same temperature of annealing. It was found that the calculated refractive index has been affected by the packing density of the thin films, whereas, the high annealing temperature gave rise to improve the homogeneity of the films. The single-oscillator model was used to analyze the optical parameters such as the oscillator and dispersion energies.     

Structural,electrical and optical properties of sol–gel AZO thin films

Transparent conductive Al-doped zinc oxide (AZO) thin films were prepared by a sol–gel method and their structural, electrical and optical properties were systematically investigated. A minimum resistivity of 4.2 × 10⁻³ Ω cm was obtained for the 650 °C-annealed films doped with 1.0 at.% Al. All films had the preferential c-axis oriented texture according to the X-ray diffraction (XRD) results. Optical transmittance spectra of the films showed a high transmittance of over 85% in the visible region and the optical band gap of the AZO films broadened with increasing doping concentration.     

Experimental and computational study of the passage of an electron beam through the curvilinear element of the Drakon stellarator system in a tenuous plasma

Results are presented from the first stage of studies on the passage of an electron beam with energy 100–500 eV in a magnetic field of 300–700 Oe through the curvilinear solenoid of the KRéL unit, the latter being a prototype of the closing segment of the Drakon stellarator system, in the plasma-beam discharge regime. The ion density at the end of the curvilinear part of the chamber, n _i ≈8×10⁸–10¹⁰ cm⁻³, the electron temperature T _e ≈4–15 eV, and the positions at which the beam hits the target for different distances from it to the electron source are determined experimentally. The motion of the electron beam is computationally modeled with allowance for the space charge created by the beam and the secondary plasma. From a comparison of the experimentally measured trajectories and trajectories calculated for different values of the space charge, we have obtained an estimate for the unneutralized ion density of the order of 5×10⁷ cm⁻³. Zh. Tekh. Fiz. 69, 22–26 (February 1999)     

Thermal oxidation of n-type ZnN films made by -sputtering from a zinc nitride target, and their conversion into p-type films

Transparent p-type thin films, containing zinc oxide phases, have been fabricated from the oxidation of n-type zinc nitride films. The zinc nitride thin films were deposited by rf-magnetron sputtering from a zinc nitride target in pure N₂ and pure Ar plasma. Films deposited in Ar plasma were conductive (resistivity 4.7×10⁻² Ω cm and carrier concentrations around 10²⁰ cm⁻³) Zn-rich Zn_xN_y films of low transmittance, whereas Zn_xN_y films deposited in N₂ plasma showed high transmittance (>80%), but five orders of magnitude lower conductivity. Thermal oxidation up to 550 C converted all films into p-type materials, exhibiting high resistivity, 10²–10³ Ω cm, and carrier concentration around 10¹³ cm⁻³. However, upon oxidation, the Zn_xN_y films did not show the zinc oxide phase, whereas Zn-rich Zn_xN_y films were converted into films containing ZnO and ZnO₂ phases. All films exhibited transmittance >85% with a characteristic excitonic dip in the transmittance curve at 365 nm. Low temperature photoluminescence revealed the existence of exciton emissions at 3.36 and 3.305 eV for the p-type zinc oxide film.     

Structural and optoelectronic properties of amorphous GaN thin films

Amorphous gallium nitride (a-GaN) thin films were deposited on glass substrate by electron beam evaporation technique at room temperature and high vacuum using N ₂ as carrier gas. The structural properties of the films was studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). It was clear from XRD spectra and SEM study that the GaN thin films were amorphous. The absorbance, transmittance and reflectance spectra of these films were measured in the wavelength range of 300–2200 nm. The absorption coefficient spectral analysis in the sharp absorption region revealed a direct band gap of E _g = 3:1 eV. The data analysis allowed the determination of the dispersive optical parameters by calculating the refractive index. The oscillator energy E ₀ and the dispersion energy E _d, which is a measure of the average strength of inter-band optical transition or the oscillator strength, were determined. Electrical conductivity of a-GaN was measured in a different range of temperatures. Then, activation energy of a-GaN thin films was calculated which equalled E _a = 0:434 eV.     

An influence of deposition temperature on structural,optical and electrical properties of sprayed ZnO thin films of identical thickness

Nanocrystalline ZnO thin films were deposited at different temperatures (T_s = 325 °C–500 °C) by intermittent spray pyrolysis technique. The thickness (300 ± 10 nm) independent effect of T_s on physical properties was explored. X-Ray diffraction analysis revealed the growth of wurtzite type polycrystalline ZnO films with dominant c-axis orientation along [002] direction. The crystallite size increased (31 nm–60 nm) and optical band-gap energy decreased (3.272 eV–3.242 eV) due to rise in T_s. Scanning electron microscopic analysis of films deposited at 450 °C confirmed uniform growth of vertically aligned ZnO nanorods. The films deposited at higher T_s demonstrated increased hydrophobic behavior. These films exhibited high transmittance (>91%), low dark resistivity (～10^?2 Ω-cm), superior figure of merit (～10^?3 Ω^?1) and low sheet resistance (～10² Ω/□). The charge carrier concentration (η -/cm³) and mobility (μ – cm²V^?1s^?1) are primarily governed by crystallinity, grain boundary passivation and oxygen desorption effects.     

The enhanced conductivity and stability of AZO thin films with a TiO2 buffer layer

Aluminum doped zinc oxide (AZO) films were substitutes of the SnO₂:F films on soda lime glass substrate in the amorphous thin-film solar cells due to good properties and low cost. In order to improve properties of AZO films, the TiO₂ buffer layer had been introduced. AZO films with and without TiO₂ buffer layer were deposited on soda lime glass substrates by r.f. magnetron sputtering. Subsequently, one group samples were annealed in vacuum (0.1 Pa) at 500 °C for 120 s using the RTA system, and the influence of TiO₂ thickness on the properties of AZO films had been discussed. The XRD measurement results showed that all the films had a preferentially oriented (0 0 2) peak, and the intensity of (0 0 2) peak had been enhanced for the AZO films with TiO₂ buffer layer. The resistivity of TiO₂ (3.0 nm)/AZO double-layer film is 4.76×10⁻⁴ Ω cm with the maximum figure merit of 1.92×10⁻² Ω⁻¹, and the resistivity has a remarkable 28.7% decrease comparing with that of the single AZO film. The carrier scattering mechanism of TiO₂ (3.0 nm)/AZO double-layer film had been described by Hall measurement in different temperatures. The average transmittance of all the films exceeded 92% in the visible spectrum. Another group samples were heat treated in the quartz tube in air atmosphere, and the effect of TiO₂ thickness on thermal stability of AZO films had been discussed.     

A wet chemical preparation of transparent conducting thin films of Al-doped ZnO nanoparticles

A wet chemical deposition method for preparing transparent conductive thin films on the base of Al-doped ZnO (AZO) nanoparticles has been demonstrated. AZO nanoparticles with a size of 7 nm have been synthesised by a simple precipitation method in refluxed conditions in ethanol using zinc acetate and Al-isopropylate. The presence of Al in ZnO was revealed by the EDX elemental analysis (1.8 at.%) and UV–Vis spectroscopy (a blue shift due to Burstein–Moss effect). The obtained colloid solution with the AZO nanoparticles was used for preparing by spin-coating thin films on glass substrates. The film demonstrated excellent homogeneity and transparency (T > 90%) in the visible spectrum after heating at 400 °C. Its resistivity turned to be excessively high (ρ = 2.6 Ω cm) that we ascribe to a poor charge percolation due to a high film porosity revealed by SEM observations. To improve the percolation via reducing the porosity, a sol–gel solution was deposited “layer-by-layer” in alternation with layers derived from the AZO colloid followed by heating. As it was shown by optical spectroscopy measurements, the density of thus prepared film was increased more than twice leading to a significant decrease in resistivity to 1.3 × 10⁻² Ω cm.