Efficiency Enhancement of Dye-Sensitized Solar Cells： Using Salt CuI as an Additive in an Ionic Liquid

Energy conversion efficiency of the dye-sensitized solar cell is improved from 3.5% to 4.5% by adding a small amount of CuI into an ionic liquid electrolyte. It is found that other copper-I salts, for example, CuBr, have the same effect for the dye-sensitized solar cell. Experimental results show that no Cu^2＋ ions exist in this electrolyte. It is suggested that this improvement is caused by the adsorption of Cu^＋ onto the TiO2 porous film.     

Low platinum loading PtNPs/graphene composite catalyst with high electrocatalytic activity for dye-sensitized solar cells

Platinum nanoparticles(PtNPs)/graphene composite materials are synthesized by a controlled chemical reduction of H2PtCl6 on graphene sheets.The electrocatalytic activity of a PtNPs/graphene composite counter electrode for a dye-sensitized solar cell(DSSC) is investigated.The results demonstrate that the PtNPs/graphene composite has high electrocatalytic activity for the dye-sensitized solar cell.The cell employing PtNPs(1.6 wt%)/graphene counter electrode reaches an conversion efficiency(η)of 3.89% upon the excitation of 100 mW/cm2 AM 1.5 white light,which is comparable to that of the cell with a Pt-film counter electrode(η=3.76%).It suggests that one can use only 14% Pt content of the conventional Pt-film counter electrode to obtain a comparable conversion efficiency.It may be possible to obtain a high performance DSSC using the PtNPs/graphene composite with a very low Pt content as a counter electrode due to its simplicity,low cost,and large scalability.     

Performance improvement of GaN-based light-emitting diode with a p-InAlGaN hole injection layer

The characteristics of a blue light-emitting diode(LED)with a p-InAlGaN hole injection layer(HIL)is analyzed numerically.The simulation results indicate that the newly designed structure presents superior optical and electrical performance such as an increase in light output power,a reduction in current leakage and alleviation of efficiency droop.These improvements can be attributed to the p-InAlGaN serving as hole injection layers,which can alleviate the band bending induced by the polarization field,thereby improving both the hole injection efficiency and the electron blocking efficiency.     

Performance improvement of GaN-based light-emitting diode with a p-InAIGaN hole injection layer

The characteristics of a blue light-emitting diode （LED） with a p-InA1GaN hole injection layer （HIL） is analyzed numerically. The simulation results indicate that the newly designed structure presents superior optical and electrical performance such as an increase in light output power, a reduction in current leakage and alleviation of efficiency droop. These improvements can be attributed to the p-InA1GaN serving as hole injection layers, which can alleviate the band bending induced by the polarization field, thereby improving both the hole injection efficiency and the electron blocking efficiency.     

Synthesis and application of TiO_2 single-crystal nanorod arrays grown by multicycle hydrothermal for dye-sensitized solar cells

TiO2 is a wide band gap semiconductor with important applications in photovoltaic cells. Vertically aligned Tit2 nanorod arrays （NRs） are grown on the fluorine-doped tin oxide （FTO） substrates by a multicycle hydrothermal synthesis process. The samples are characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, high-resolution transmission electron microscopy （HRTEM）, and selected-area electron diffraction （SAED）. It is found that dye-sensitized solar cells （DSSCs） assembled by the as-prepared Tit2 single-crystal NRs exhibit different trends under the condition of different nucleation and growth concentrations. Optimum cell performance is obtained with high nucleation concentration and low growth cycle concentration. The efficiency enhancement is mainly attributed to the improved specific surface area of the nanorod.     

Optical Performance of N-Face A1GaN Ultraviolet Light Emitting Diodes

The optical property and injection efficiency of N-face A1GaN based ultraviolet light emitting diodes （UV-LEDs） are studied and compared with Ga-face A1GaN based UV-LEDs. A staircase electron injector is introduced in the N-face AIGaN based UV-LED. The electroluminescence spectra, power-current performance curves, energy band diagrams, carrier concentration and radiative recombination rate are numerically calculated. The results indicate that the N-face UV-LED has a better optical performance than the Ga-face UV-LED, and the injection efficiency is enhanced owing to the fact that the staircase electron injector is available for UV-LEDs.     

Improved performance of InGaN light-emitting diodes with a novel sawtooth-shaped electron blocking layer

A sawtooth-shaped electron blocking layer is proposed to improve the performance of light-emitting diodes （LEDs）. The energy band diagram, the electrostatic field in the quantum well, the carrier concentration, the electron leakage, and the internal quantum efficiency are systematically studied. The simulation results show that the LED with a sawtooth-shaped electron blocking layer possesses higher output power and a smaller efficiency droop than the LED with a conventional A1GaN electron blocking layer, which is because the electron confinement is enhanced and the hole injection efficiency is improved by the appropriately modified electron blocking layer energy band.     

Simulation study of blue InGaN multiple quantum well light-emitting diodes with different hole injection layers

InGaN-based light-emitting diodes with p-GaN and p-AlGaN hole injection layers are numerically studied using the APSYS simulation software.The simulation results indicate that light-emitting diodes with p-AlGaN hole injection layers show superior optical and electrical performance,such as an increase in light output power,a reduction in current leakage and alleviation of efficiency droop.These improvements can be attributed to the p-AlGaN serving as hole injection layers,which can alleviate the band bending induced by the polarization field,thereby improving both the hole injection efficiency and the electron blocking efficiency.     

High-Order-Harmonic Generation from a Relativistic Circularly Polarized Laser Interacting with Over-Dense Plasma Grating

The simple surface current model is extended to study the generation of high-order harmonics for a relativistic circularly polarized laser pulse interacting with a plasma grating surface. Both exact relativistic electron dynamics and optical interference of surface periodic structure are considered. It is found that high order harmonics in the specular direction are obviously suppressed whereas the harmonics of the grating periodicity are strongly enhanced and folded into small solid angles with respect to the surface direction. The conversion efficiency of certain harmonics is five orders of magnitude higher than that of the planar target cases. It provides an effective approach to generate a coherent radiation within the so-called ‘water window' while maintaining high conversion efficiency and narrow angle spread.     

Instability of lithium bis(fluorosulfonyl)imide(LiFSI)–potassium bis(fluorosulfonyl)imide(KFSI) system with LiCoO_2 at high voltage

The cycling performance, impedance variation, and cathode surface evolution of the Li/LiCoO2 cell using Li FSI–KFSI molten salt electrolyte are reported. It is found that this battery shows poor cycling performance, with capacity retention of only about 67% after 20 cycles. It is essential to understand the origin of the instability. It is noticed that the polarization voltage and the impedance of the cell both increase slowly upon cycling. The structure and the properties of the pristine and the cycled LiCoO2 cathodes are investigated by x-ray diffraction(XRD), scanning electron microscopy(SEM), Raman spectroscopy, x-ray photoelectron spectroscopy(XPS), and transmission electron microscopy(TEM). It is found that the LiCoO2 particles are corroded by this molten salt electrolyte, and the decomposition by-product covers the surface of the LiCoO2 cathode after 20 cycles. Therefore, the surface side reaction explains the instability of the molten salt electrolyte with LiCoO2.     

Hydrothermal growth of large-scale macroporous TiO<Subscript>2</Subscript> nanowires and its application in 3D dye-sensitized solar cells

Large-scale macroporous TiO₂ nanowires (MTN) were directly grown on spiral-shaped titanium wires as photoanodes of dye-sensitized solar cells (DSSCs) via a facile hydrothermal reaction without any seeds, templates, and TiO₂ powder. The MTN thin film was characterized by SEM, XRD and TEM. The studies revealed that the MTN thin film had better mechanical properties and provided an efficient pathway for the diffusion of liquid electrolyte. The efficiency of 0.86% for the 3D DSSC was obtained with a J _sc of 2.30 mA/cm², V _oc of 616 mV, and FF of 0.61. This MNT-based mini 3D DSSC is a promising photovoltaic device for applications in the fields of high-integrated micro-electronic equipment.     

Poly(vinyl chloride)-<Emphasis Type="Italic">graft</Emphasis>-poly(<Emphasis Type="Italic">N</Emphasis>-vinyl caprolactam) graft copolymer: synthesis and use as template for porous TiO<Subscript>2</Subscript> thin films in dye-sensitized solar cells

Poly(N-vinyl caprolactam) (PNVCL) side chains were grafted to a poly(vinyl chloride) (PVC) backbone via atom transfer radical polymerization. The synthesized PVC-g-PNVCL graft copolymer was templated for the preparation of porous TiO₂ thin films, which involved a sol–gel reaction and calcination process. The interaction of the carbonyl groups in the PVC-g-PNVCL with the titania was revealed by FT-IR spectroscopy. X-ray diffraction and transmission electron microscopy analysis showed the formation of porous TiO₂ thin films with the anatase phase. A series of porous TiO₂ thin films with different pore sizes and porosities was prepared by varying the solution compositions and were used as photoelectrodes in dye-sensitized solar cells (DSSC) with a polymer electrolyte. The DSSC performed best when using the TiO₂ film with higher porosity, lower interfacial resistance, and longer electron life time. The highest energy conversion efficiency, photovoltage (V _oc), photocurrent density (J _sc), and fill factor (FF) were 1.2%, 0.68 V, 3.2 mA/cm², and 0.57 at 100 mW/cm², respectively, for the quasi-solid state DSSC with a 730-nm-thick TiO₂ film.     

Natural dye-based photoelectrode for improvement of solar cell performance

In the present paper, photovoltaic studies of dye-sensitized solar cells (DSSCs) based on betacyanin/TiO₂ and betacyanin/WO₃–TiO₂ have been done. The cell performances were compared through I–V curves and wavelength dependant photocurrent measurements for the two new types of DSSCs. The TiO₂-coated DSSC showed the photovoltage and photocurrent of 300 mV and 4.96 mA/cm², whereas the cell employing WO₃–TiO₂ photoelectrode showed the values 435 mV and 9.86 mA/cm², respectively. The conversion efficiency of TiO₂ based dye-sensitized solar cell was found to be 0.69 %, while WO₃–TiO₂-based cell exhibited a higher conversion efficiency of 2.2 %. The better performance of the WO₃–TiO₂ dye-sensitized solar cell photoelectrode is thought to be due to an inherent energy barrier at the electrode/electrolyte interface leading to the reduced recombination of photoinduced electrons.     

Ionic liquid type dye-sensitized solar cells: increases in photovoltaic performances by adding a small amount of water

Increases in photovoltaic performances for dye-sensitized solar cells having ionic liquid type electrolytes are reported. These results are explained by diffusion coefficient for I₃⁻, charge transfer resistances on counter electrodes, flat band potentials of TiO₂, redox potentials for I⁻/I₃⁻, electron diffusion constants, electron life time, and diffusion length in TiO₂ layers. Methylpropylimidazolium iodide is selected because of the lowest viscosity and the highest conductivity. Increases in the photovoltaic performance are observed when a small amount of water was added into the ionic liquid consisting of both LiI and t-butylpyridine as the additives. These improvements are brought about by enhancements of all of J_sc, ff and V_oc. The increases in J_sc and ff are associated with the decrease in charge transfer resistances on counter electrodes and increases in ionic conductivities. V_oc may be explained by an increase in the difference between redox potentials of I⁻/I₃⁻ and Fermi level.     

Applications of vertically oriented TiO2 micro-pillars array on the electrode of dye-sensitized solar cell

In this research, dye-sensitized solar cells based on TiO₂ micro-pillars fabricated by inductive couple plasma etcher were investigated by analyses of X-ray diffraction (XRD), scanning electron microscopy (SEM), contact angle, ultraviolet-visible absorption spectra (UV-vis), and current-voltage characteristics. X-ray diffraction patterns show that the TiO₂ anatase phase forms while sintering at 450 °C for 30 min. The SEM images reveal that the diameter and height of TiO₂ micro-pillars are about 3 and 0.8 μm, respectively. The measurements of contact angle between TiO₂ micro-pillars and deionized water (DI water) reveal that the TiO₂ micro-pillars is super-hydrophilic while annealed at 450 °C for 30 min.The absorption spectrum of TiO₂ micro-pillars is better than TiO₂ thin film and can be widely improved in visible region with N3 dye adsorbed. The results of current-voltage (I-V) characteristics analysis reveal that dye-sensitized solar cell with TiO₂ micro-pillars electrode has better I-V characteristics and efficiency than TiO₂ film electrodes. This result may be due to the annealed TiO₂ micro-pillars applied on the electrode of dye-sensitized solar cell can increase the contact area between TiO₂ and dye, resulting in the enhancement of I-V characteristics and efficiency for dye-sensitized solar cell.     

Effects of electrode film modifications on the open-circuit photovoltage in enhanced dye-sensitized solar cells

In this study, the open-circuit photovoltage (V _oc) decay technique was used to investigate the relationship between the electrode film morphology and the open-circuit photovoltage. Results indicate that dye-sensitized solar cells (DSCs) based on ordered arrays of TiO₂ nanostructures (100 nm external diameters and 20–50 nm internal diameters) generally show higher open-circuit photovoltage (V _oc) values than those based on sintered TiO₂ nanoparticles (20–40 nm diameters). In particular, cells based on thick nanotubules (wall thickness ≥ 45 nm in our research) and on nanorods (100 nm diameters) show particularly high V _oc values, indicating slow recombination kinetics under open-circuit conditions. It can be argued that the nanorods and the thick nanotubules act like singles crystals and therefore the injected electrons in the inner TiO₂ molecules are shielded from holes in the electrolyte under open-circuit conditions. The open-circuit recombination time constant of electrons accumulated in the TiO₂ conduction band is therefore prolonged and resulting in high V _oc values.     

Symbiotic organism search algorithm for simulation of <Emphasis Type="Italic">J</Emphasis>-<Emphasis Type="Italic">V</Emphasis> characteristics and optimizing internal parameters of DSSC developed using electrospun TiO<Subscript>2</Subscript> nanofibers

In the present investigation, the recently developed, simple, robust, and powerful metaheuristic symbiotic organism search (SOS) algorithm was used for simulation of J-V characteristics and optimizing the internal parameters of the dye-sensitized solar cells (DSSCs) fabricated using electrospun 1-D mesoporous TiO₂ nanofibers as photoanode. The efficiency (η =?5.80%) of the DSSC made up of TiO₂ nanofibers as photoanode is found to be ～ 21.59% higher compared to the efficiency (η =?4.77%) of the DSSC made up of TiO₂ nanoparticles as photoanode. The observed high efficiency can be attributed to high dye loading as well as high electron transport in the mesoporous 1-D TiO₂ nanofibers. Further, the validity and advantage of SOS algorithm are verified by simulating J-V characteristics of DSSC with Lambert-W function.     

TiO2表面质子化对染料敏化太阳能电池性能及吸附染料稳定性的影响

采用致密平整TiO₂薄膜作为染料敏化太阳能电池光电极,并研究了HCl处理表面质子化对电池性能的影响. 结果表明,HCl处理后电池的短路电流显著提升,电池的开路电压则有轻微的下降,电池电流提升了31%,而能量转化效率则提升了25%. 这是因为TiO₂的表面质子化增强了吸附染料与TiO₂间的电学耦合,提高了染料中激发电子向TiO₂导带的注入速率. 而电压的下降,一方面是由于质子化会引起TiO₂导带能级     

Porous PVdF-HFP/P123 electrolyte membrane containing flexible quasi-solid-state dye-sensitized solar cells produced by the compression method

Flexible quasi-solid-state dye-sensitized solar cells (DSSCs) with porous poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP)/polyethylene oxide-co-polypropylene oxide-co-polyethylene oxide (P123) electrolyte membranes were fabricated and their photocurrent–voltage (I–V) characteristics are studied. Flexible TiO₂ photoelectrodes were prepared using the compression method and porous PVdF-HFP/P123 membranes, by the nonsolvent-induced phase inversion technique. To activate the electrolyte membrane, the membrane was immersed in liquid-state electrolyte. Increased compression pressure improved the interconnection between TiO₂ nanoparticles, enhancing the photovoltaic performances of the flexible liquid-state DSSCs to a maximum of 3.92% efficiency. Meanwhile, the overall pore structure of the PVdF-HFP/P123 membranes was controlled by varying the blend ratio of P123 to PVdF-HFP. Membranes higher in P123 content gave larger pores and pore volume, increasing the electrolyte uptake of the porous membrane, and thus the ionic conductivity of the electrolyte membrane as well. The photovoltaic characteristics of the flexible quasi-solid-state DSSCs containing a porous PVdF-HFP/P123 electrolyte membrane showed a maximum at 50 wt% P123 content, which gave a short-circuit current density (J_sc) value of 7.28 mA/cm², an open-circuit voltage (V_oc) of 0.67 V, a fill factor (FF) of 0.61 and an energy conversion efficiency (η) of 2.98%. Furthermore, the device designed in this study showed good durability compared to those based on liquid-state electrolyte.