A new laser direct etching method of indium tin oxide electrode for application to alternative current plasma display panel

For cost effective fabrication and time of alternative current plasma display panels (AC PDPs), an indium tin oxide (ITO) layer was patterned directly with a Q-switched diode pumped Nd:YVO₄ laser (λ = 1064 nm). As experimental results, 500 mm/s scan speed with 40 kHz repetition rate was suitable for the application to AC PDP ITO electrode. In comparison with the chemically wet-etched ITO patterns by photolithography method, laser-ablated ITO patterns showed the formation of shoulders at the edge of the ITO lines and a ripple-like structure of the etched bottom. By dipping the laser-ablated ITO films in the chemical etching solution for 30 s at 50 °C, the shoulders were effectively removed without affecting the discharging properties of AC PDP.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Dependence of intermediated noble metals on the optical and electrical properties of ITO/metal/ITO multilayers

Sn doped In₂O₃ (ITO) single layer and a sandwich structure of ITO/metal/ITO (IMI) multilayer films were deposited on a polycarbonate substrate using radio-frequency and direct-current magnetron sputtering process without substrate heating. The intermediated metal films in the IMI structure were Au and Cu films and the thickness of each layer in the IMI films was kept constant at 50 nm/10 nm/40 nm. In this study, the ITO/Au/ITO films show the lowest resistivity of 5.6 × 10⁻⁵ Ω cm.However the films show the lower optical transmission of 71% at 550 nm than that (81%) of as deposited ITO films. The ITO/Cu/ITO films show an optical transmittance of 54% and electrical resistivity of 1.5 × 10⁻⁴ Ω cm. Only the ITO/Au/ITO films showed the diffraction peaks in the XRD pattern. The figure of merit indicated that the ITO/Au/ITO films performed better in a transparent conducting electrode than in ITO single layer films and ITO/Cu/ITO films.     

Surface modification of indium tin oxide films by amino ion implantation for the attachment of multi-wall carbon nanotubes

Amino ion implantation was carried out at the energy of 80 keV with fluence of 5 × 10¹⁵ ions cm⁻² for indium tin oxide film (ITO) coated glass, and the existence of amino group on the ITO surface was verified by X-ray photoelectron spectroscopy analysis and Fourier transform infrared spectra. Scanning electron microscopy images show that multi-wall carbon nanotubes (MWCNTs) directly attached to the amino ion implanted ITO (NH₂/ITO) surface homogeneously and stably. The resulting MWCNTs-attached NH₂/ITO (MWCNTs/NH₂/ITO) substrate can be used as electrode material. Cyclic voltammetry results indicate that the MWCNTs/NH₂/ITO electrode shows excellent electrochemical properties and obvious electrocatalytic activity towards uric acid, thus this material is expected to have potential in electrochemical analysis and biosensors.     

Pulsed Nd:YAG laser depositions of ITO and DLC films for OLED applications

Indium-tin oxide (ITO) films deposited on heated and non-heated glass substrates by a pulsed Nd:YAG laser at 355 nm and ∼2.5 J/cm² were used in the fabrication of simple organic light-emitting diodes (OLEDs), ITO/(PVK + Alq₃ + TPD)/Al. The ITO was deposited on heated glass substrates which possessed resistivity as low as ∼3 × 10⁻⁴ Ω cm, optical transmission as high as ∼92% and carrier concentration of about ∼5 × 10²⁰ cm⁻³, were comparable to the commercial ITO. Substrate heating transformed the ITO microstructure from amorphous to polycrystalline, as revealed by the XRD spectrum. While the polycrystalline ITO produced higher OLED brightness, it was still lower than that on the commercial ITO due to surface roughness. A DLC layer of ∼1.5 nm deposited on this ITO at laser fluence of >12.5 J/cm² improved its device brightness by suppressing the surface roughness effect.     

Electroluminescence with micro-watt output from ultra-small sized Si quantum dots/amorphous SiO2 multilayers prepared by laser crystallization method

We report the fabrication of Si quantum dots (QDs)/SiO₂ multilayers by using KrF excimer laser (248 nm) crystallization of amorphous Si/SiO₂ multilayered structures on ITO coated glass substrates. Raman spectra and transmission electron microscopy demonstrate the formation of Si QDs and the size can be controlled as small as 1.8 nm. After laser crystallization, Al electrode is evaporated to obtain light emitting devices and the room temperature electroluminescence (EL) can be detected with applying the DC voltage above 8 V on the top gate electrode. The luminescent intensity increases with increasing the applied voltage and the micro-watt light output is achieved. The EL behaviors for samples with different Si dot sizes are studied and it is found that the corresponding external quantum efficiency is significantly enhanced in sample with ultra-small sized Si QDs.     

Patterning of nanoparticulate transparent conductive ITO films using UV light irradiation and UV laser beam writing

Indium tin oxide (ITO) thin film is one of the most widely used as transparent conductive electrodes in all forms of flat panel display (FPD) and microelectronic devices. Suspension of already crystalline conductive ITO nanoparticles fully dispersed in alcohol was spun, after modifying with coupling agent, on glass substrates. The low cost, simple and versatile traditional photolithography process without complication of the photoresist layer was used for patterning ITO films. Using of UV light irradiation through mask and direct UV laser beam writing resulted in an accurate linear, sharp edge and very smooth patterns. Irradiated ITO film showed a high transparency (∼85%) in the visible region. The electrical sheet resistance decrease with increasing time of exposure to UV light and UV laser. Only 5 min UV light irradiation is enough to decrease the electrical sheet resistance down to 5 kΩ□.     

Structural properties of single and multilayer ITO and TiO2 films deposited by reactive pulsed laser ablation deposition technique

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser. The films were deposited on SiO₂ substrates heated at 200 and 400 °C. ITO and TiO₂ films with uniform thicknesses of about 400 and 800 nm, respectively, over large areas were prepared. X-ray diffraction (XRD) analysis revealed that the ITO films are formed of highly orientated nanocrystals with an average particle size of 10-15 nm. Atomic force microscopy (AFM) observations indicate rough ITO films surfaces with average roughness of 26-30 nm. Pores were also observed. TiO₂ films deposited on the prepared ITO films result less crystalline. Annealing at 300 and 500 °C for three consecutive hours promoted formation of TiO₂ anatase phase, with crystal size of ∼6-7 nm. From the scanning transmission electron microscope (STEM) images, it can be seen that the TiO₂ films deposited onto the prepared ITO films present a relatively high pore sizes with an average pore diameter of ∼40 nm and excellent uniformity. In addition, STEM cross-sectional analysis of our films showed a columnar structure but no evidence of voids in the structure. Therefore, films exhibited large surface area, well suited for dye-sensitized solar cells (DSSC) applications.     

Pockels effect of water in the electric double layer at the interface between water and transparent electrode

We have obtained the first experimental evidence for the Pockels effect of water, which is induced by a high electric field in the electric double layer (EDL) on the water-transparent electrode interface. The electric-field induced energy shift of the visible interference fringes of a 300 nm indium-tin-oxide (ITO) electrode layer is observed, indicating a negative refractive index change at the interface. Numerical calculation reproduces well the experimental observation, showing that the signal mainly originates from water in the EDL. The Pockels constants of water are estimated to be r₃₃ = 5.1 × 100 pm/V and r₁₃ = 1.7 × 100 pm/V. The large anisotropy of the Pockels effect of water is deduced from the incidence angle dependence of the p-polarization signal. At the same time, the ITO shows a blue shift of the band gap in the UV due to the band population effect in the space charge layer. The plasma frequency in the near IR is also expected to increase due to the band population effect, since the ITO has a high doped carrier population close to metal. A negative refractive index change in the ITO space charge layer is induced from both effects, but its effect on the signal is estimated to be much smaller than that of the negative refractive index change of water in the EDL.     

Optimized laser cutting on light guide plates using grey relational analysis

This paper present the optimum conditions for direct CO₂ laser cutting of 6-mm-thick polymethylmethacrylate (PMMA) for backlit module applications. The influence of the major processing parameters on the optical transmittance ratio and surface roughness of cut samples material have been discussed. In order to assess the effects of several operational parameters on multiple-performance characteristics, we applied the grey relational analysis method. In this paper, we studied the effects of several laser direct cut parameters, such as assisted gas-flow rate, pulse repetition frequency, cutting speed, and focus position to achieve optimum characteristics for two product characteristics, optical transmittance ratio and work-piece surface roughness. The study involved nine experiments based on an orthogonal array, and results indicate the optimal process parameters as 20 NL/min for assisted-gas flow rate, 5 kHz for pulse repetition frequency, 2 mm/s for cutting speed, and 0 mm for laser focusing position. Additionally, by analyzing the grey relational grade, we found that the assisted-gas flow rate has more influence than any other single parameter.