Luminescence Spectra of SrA112O19：Pr^3＋, Mn^2＋ under VUV-UV Excitation

Luminescence spectra of SrAl12O19：Pr^3＋,Mn^2＋ under VUV-UV excitation are investigated. The characteristic emissions between 4f levels and the excitation of 5d for Pr^3＋ are observed. The emission of Mn^3＋ peaks at 517nm and the excitations clue to the ground to multiplets are observed at 276, 360, 386 and 426nm. However, the spectral overlap between the emission of Pr^3＋ and excitation of Mn^2＋ is absent, suggesting that the quantum splitting cannot be achieved via a Pr^3＋ Mn^2＋ ion pair in the host SrAl12O19.     

Preparation and Luminescence Characteristics of Ca3Y2（BO3）4：Eu^3＋ Phosphor

Ca3Y2 （BO3）4：Eu^3＋ phosphor is synthesized by high temperature solid-state reaction method, and the Iuminescence characteristics are investigated. The emission spectrum exhibits two strong red emissions at 613 and 621 nm corresponding to the electric dipole ^5 Do- ^7F2 transition of Eu^3＋ under 365 nm excitation, the reason is that Eu^3＋ substituting for Y^3＋ occupies the non-centrosymmetric position in the crystal structure of Ca3 Y2 （BO3）4. The excitation spectrum for 613 nm indicates that the phosphor can be effectively excited by ultraviolet （UV） （254 nm, 365nm and 400nm） and blue （470nm） light. The effect of Eu^3＋ concentration on the emission intensity of Ca3 Y2 （BO3）4 ：Eu^3＋ phosphor is measured, the result shows that the emission intensities increase with increasing Eu^3＋ concentration, then decrease. The CIE colour coordinates of Ca3Y2 （BO3）4：Eu^3＋ phosphor is （0.639, 0.357） at 15mol% Eu^3＋.     

VUV/UV/X-Ray Excited Luminescent Properties of Eu^3＋ and Pr^3＋ Doped BiSbO4

Absorption spectra of BiSbO4 are studied. The electronic structure calculated by the DFT shows that BiSbO4 is a semiconductor, with direct band gap 2.96 eV, which is consistent with UV-visible diffuse reflectance experiment. The host lattice emission band is located at 440 nm under VUV excitation. Eu^3＋ and Pr^3＋ doped samples have high luminescence efficiency in emitting red and green light, respectively. From the partial density of states, Eu^3＋ doped emitting spectrum, and the host crystal structure parameters, the relationship between structure and optical properties is discussed. It is found that the Eu^3＋ ions occupied Bi^3＋ sites, and there could be an energy transfer from Bi^3＋ ions to RE^3＋ ions.     

Spectroscopic investigation of a new crystal： Nd^3＋,Yb^3＋：YVO4

The absorption and emission spectra of the YVO4 single crystal co-doped with 1 at.% Nd^3＋ and 1 at.% Yb^3＋ are investigated. The efficient Nd^3＋ → Yb^3＋ energy transfer and the back transfer （Yb^3＋ → Nd^3＋） are observed at room temperature. The fluorescence lifetime of the 4F3/2 level of Nd^3＋ in Nd,Yb：YVO4 is measured under 808 nm laser light excitation. The efficiency of Nd^3＋ → Yb^3＋ energy transfer in YVO4 is determined to be about 34%.     

Visible Upconversion Emission in Er3＋—Doped GeO2—PbO—PbF2 Glass

The upconversion fluorescence emission of Er3 -doped 60GeO2-2OPbO-2OPbF2 glass was experimentally investigated under the pump of 976-nm laser diode. The results reveal the existence of intense emission bands centred around 524, 545, and 657nm at room temperature. The green emission at 524 and 545nm is due to the 4S3/2 2 Hll/2→ 4I15/2 transition and the red emission of 657nm originates from the 4F9/2-→4I15/2 transition of Er3 . The quadratic dependence of the green and red emissions on excitation power indicates that a two-photonabsorption process occurs under the 976-nm excitation. The excited- state absorption from 4I ll/2 and the cross relaxation between two Er3 ions in the 4I ll/2 state contribute to the green emission. The red emission at 657nm is attributed to the excited-state absorption and cross relaxation processes in the 4I13/2 level as well as the 4S3/2 level nonradiative transition of Er3 .     

Influence of Surface Quenching Effects on Luminescent Dynamics of ZnS：Mn^2＋ Nanocrystals

A model describing surface quenching of isolated ion centres in nanocrystals is proposed based on the energy transfer between the doped ions and the nanocrystalline surface quenching centres. The quenching rate depends on the position of the ions in the nanocrystal, hence the decay curve under non-selective excitation is generally nonexponential. The decay curve calculated with this model is in good agreement with that of the ^4T1→^6A1 emission in ZnS：Mn^2＋ nanocrystals.     

Hydrothermal Synthesis and Vacuum Ultraviolet-Excited Luminescence Properties of Novel Dy^3＋-doped GdPO4 White Light Phosphors

Novel Dy^3＋-doped GdPO4 white light phosphors with a monoclinic system are successfully synthesized by the hydrothermal method at 240℃. The strong absorption at around 147nm in the excitation spectrum is assigned to the host absorption. It is suggested that the vacuum ultraviolet excited energy is transferred from the host to the Dy^3＋ ions. The f - d transition of the Dy^3＋ ion is observed to be located at 182nm, which is consistent with the calculated value using Dorenbos＇s expression. Under 147nm excitation, Gd0.92PO4：0.08Dy^3＋ phosphor exhibits two emission bands located at 572 nm （yellow） and 478 nm （blue）, which correspond to the hypersensitive transitions ^4 F9/2-^6 H13/2 and ^4 F9/2-^6 H15/2. The two emission bands lead to the white light. Because of the strong absorption at about 147nm, Gd0.92PO4：0.08Dy^3＋ under vacuum ultraviolet excitation is an effective white light phosphor, and has promising applications to mercury-free lamps.     

Upconversion Luminescence Dynamics in Er^3＋/Yb^3＋ Codoped Nanocrystalline Yttria

The upconversion luminescence and dynamics in Er^3＋ /Yb^3＋ codoped nanocrystalline yttria （7-65 nm） are studied under 980-nm pulsed laser excitation, It is found that the red emission of ^4F9/2-^4I15/2 and the green emission of ^2H11/2/^4S3/2 in nanoparticles with lower concentration of Yb^3＋ result from a two-photon excitation, In nanocrystals with higher Yb^3＋ concentration, the red emissions from a two-photon excitation, while the green emissions from a three-photon excitation, The luminescence dynamics indicates that as the particle size decreases, both the rise and the decay time constants become shorter, As the size decreases to several nanometres, the rise process nearly disappears, suggesting that the upconversion luminescence originates mainly from self-excitation of Er^3＋, instead of the energy transfer of Yb^3＋→ Er^3＋.     

Luminescence and Energy Transfer of Eu^2＋, Mn^2＋ in SrZnP2O7

The SrZnP2OT：Eu^2＋, Mn^2＋ phosphor is synthesized by high temperature solid state reaction. The luminescence properties and the energy transfer between Eu^2＋ and Mn^2＋ are investigated. The emission bands of this phosphor peaked at 42Ohm and 67Ohm are originated from the 5d → 4f transition of Eu^2＋ and from the 4T1 （4G） --〉 6A1 （6S） transit/on of Mn^2＋, respectively. With the increasing Mn^2＋ concentration, the intensity of fixed concentra- tion Eu^2＋ decreases and the intensity of Mn^2＋ also increases. It is suggested that there is an energy transfer from Eu^2＋ to Mn^2＋ in SrZnP2O7 host. According to Dexter＇s energy transfer formula of multipolar interaction, the energy transfer between Eu^2＋ and Mn^2＋ is due to the electric dipole-quadrupole interaction of the resonance transfer.     

Sr3Bi（PO4）3：Eu^2＋ Luminescence,Concentration Quenching and Crystallographic Sites

A blue emitting phosphor Sr3Bi（PO4）3：Eu2＋ is synthesized luminescent property is investigated. Sr3Bi（PO4 ）3 ：Eu^2＋ can by a high-temperature solid state method, and its create blue emission under the 332 radiation excitation, and the prominent luminescence in blue （423nm） due to the 4fSd^1→4f^7 transition of the Eu^2＋ ion. The crystallographic sites of the Eu^2＋ ion in Sr3Bi（PO4）3 are analyzed, and the 420 and 440 nm emission peaks of the Eu^2＋ ion are assigned to the nine-coordination and eight-coordination, respectively. The emission intensity of Sr3Bi（PO4）3：Eu^2＋ is influenced by the Eu^2＋ doping content, and the concentration quenching effect is observed. The quenching mechanism is the dipole-dipole interaction, and the critical distance of energy transfer is calculated by the concentration quenching method to be approximately 1.72nm.     

High elastic modulus in b-axis-oriented single crystal V2O5

The elastic moduli of V₂O₅ are of great importance for the assessment of the buildup of strain during thin-film growth as well as for the analysis of defect generation and propagation. The usually rather small crystal dimensions make a precise experimental determination of the elastic constants highly challenging and only very little is known about the temperature dependent strain evolution. Here large V₂O₅ single crystals grown with different parameter sets are investigated by ultrasonic pulse experiments and by sampled continuous wave ultrasound spectroscopy. The elastic modulus C₂₂ is determined to be 220 GPa at room temperature. Temperature dependent investigations of the elastic behavior show that ultrasonic experiments are suitable for highly sensitive detection of oxygen-deficient phases in rapidly grown samples. In addition they indicate the presence of temperature dependent elastic instabilities in inhomogeneous samples.     

Ordered zinc-vacancy induced Zn0.75Ox nanophase structure

Using transmission electron microscopy, a new nano-phase structure of Zn_0.75O_x induced by Zn-vacancy has been discovered to grow on wurtzite ZnO nanobelts. The superstructure grows epitaxial from the surface of the wurtzite ZnO nanobelts and can be fitted as an orthorhombic structure, with lattice parameters a′=2a, and c′=c, where a and c are the lattice parameters of ZnO. The superstructured phase is resulted from high-density Zn vacancies orderly distributed in the ZnO matrix. This study provides direct observation about the existence of Zn-vacancies in ZnO.     

Thermoluminescence glow curves analysis of pure and CeO2-doped Li2O-Al2O3-SiO2 glass ceramics

A comparative study of the thermoluminescence (TL) emission between beta-irradiated lithium aluminosilicates, Li₂O-Al₂O₃-SiO₂ (LAS), and beta-irradiated CeO₂-doped lithium aluminosilicates, Li₂O-Al₂O₃-SiO₂-CeO₂ (LAS:Ce), grown by sol-gel technique and preannealed at 1250 °C is presented. It is found that doping reinforces the result of preannealing the sample; the incorporation of CeO₂ at low concentrations shifts the TL curves towards higher temperatures and increases the total intensity with respect to samples without the dopant. This behavior, together with the fact that CeO₂ is a good densification agent, suggests the possibility of using CeO₂ to improve the technological properties of LAS. Deconvolution analysis of the thermoluminescence glow curves of doped materials under general order kinetics shows that the relevant temperatures at which the component signals appear are virtually the same as for pure samples. This suggests that CeO₂ does not introduce new types of traps, but only changes the population and distribution of impurities responsible for the TL in the original matrix of LAS. Finally, the kinetic parameters for the deconvoluted curves are reported. They corroborate that changes in CeO₂ concentration only vary the depth and distribution of the same kind of original traps.     

Growth of α-Al2O3:C crystal with highly sensitive optically stimulated luminescence

In this work, an α-Al₂O₃:C crystal was directly grown by the temperature gradient technique (TGT) using Al₂O₃ and graphite powders as the raw materials. The optical, optically stimulated luminescence (OSL) properties and dosimetric characteristics of as-grown crystal were investigated. As-grown α-Al₂O₃:C crystal shows strong absorption band at 205, 230 and 256 nm. Three-dimensional thermoluminescence (TL) emission spectrum of the crystal shows a single emission peak at ∼415 nm. The OSL decay curve can be fitted to two exponentials, the faster component and the slower component. The OSL response of the crystal shows a linear-sublinear-saturation characteristic. As-grown α-Al₂O₃:C crystal shows excellent linearity in the dose range from 5×10⁻⁶ to 50 Gy. For doses higher than the saturation dose (100 Gy), the OSL sensitivity decreases as the dose increases.     

The optical properties of planar waveguides in LiB3O5 crystals formed by Cu implantation

A planar optical waveguide has been formed in a LiB₃O₅ crystal using 6.0 MeV Cu⁺-ions with a dose of 1 × 10¹⁵ ions/cm² at room temperature. Possible propagating modes were measured at a wavelength of 633 nm using the prism-coupling method. The refractive index profiles of the waveguide were reconstructed by an effective refractive index method and the beam propagation method was used to investigate the properties of the propagation modes in the formed waveguide. The results suggest that the fundamental TE₀ and TM₀ modes may be well-confined and propagate a longer distance inside the waveguide. The implantation process was also simulated using the transport of ions in matter code (TRIM), which indicates that the nuclear energy deposition may be the main factor for the refractive index change.     

Enhancement of initial permeability due to Mn substitution in polycrystalline Ni0.50−xMnxZn0.50Fe2O4

The structural and magnetic properties of Mn substituted Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.00, 0.10 and 0.20) sintered at various temperatures have been investigated thoroughly. The lattice parameter, average grain size and initial permeability increase with Mn substitution. Both bulk density and initial permeability increase with increasing sintering temperature from 1250 to 1300 °C and above 1300 °C they decrease. The Ni_0.30Mn_0.20Zn_0.50Fe₂O₄ sintered at 1300 °C shows the highest relative quality factor and highest initial permeability among the studied samples. The initial permeability strongly depends on average grain size and intragranular porosity. From the magnetization as a function of applied magnetic field, M(H), it is clear that at room temperature all samples are in ferrimagnetic state. The number of Bohr magneton, n(μ_B), and Neel temperature, T_N, decrease with increasing Mn substitution. It is found that Mn substitution in Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.20) decreases the Neel temperature by 25% but increases the initial permeability by 76%. Possible explanation for the observed characteristics of microstructure, initial permeability, DC magnetization and Neel temperature of the studied samples are discussed.     

Microstructure evolution in the rapidly quenched Fe78Si9B13 ribbons

We report microstructure evolution in as-spun Fe₇₈Si₉B₁₃ ribbons under various wheel speeds (s), which was investigated by X-ray diffraction (XRD), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). With decreasing s, the volume fraction of the residual amorphous phase (V_a) in the as-spun ribbons decreases gradually, and the total exothermic heat of the crystallization in the DSC curves also decreases, but the ratio of the exothermic heat of the second crystallization to the first one is on the contrary. α-Fe is found in the ribbon with s of 32.9 m/s, while α-Fe, eutectic α-Fe+Fe₂B, and Fe₃Si phases are found in ribbons with s of 25.6 and 18.3 m/s. The phase precipitating behavior in cooling processes is well consistent with the annealing process in the literatures.     

Computer simulation of intrinsic defects in YAlO3 single crystal

Computer simulation techniques were used to investigate intrinsic defects in YAlO₃ single crystal. A set of short-range potential parameters were derived using a relaxed fitting procedure incorporating with the known crystal properties. These parameters were then applied within the framework of the shell model. The simulation results reveal that oxygen Frenkel disorder and the antisite defect of Al ion substituting the Y ion dominate the intrinsic defects in YAlO₃. An analysis of redox reactions corroborate that the oxidation is most likely to occur via forming interstitial oxygen, while the oxidation via filling oxygen vacancies and reduction reaction may predominate at high temperature. The activation energy of oxygen vacancy migration on conduction was also studied.     

Twin-microstructure enhanced magnetoresistance in La0.67Ba0.33MnO3 oxides

The grain growth dependence of microstructure and its effects on magnetic and transport properties are studied in the polycrystalline La_0.67Ba_0.33MnO₃ oxides. It is found that a lateral growth manner along a certain direction and a concentric terrace pattern along three orthogonal axes occur in the samples sintered at 1573 and 1673 K, respectively. Lamella-like twin microstructure forms in the concentric terrace growth pattern and the magnetoresistance properties can be enhanced by the twin microstructure. It suggests that the twin-boundaries in twin-grains may possibly induce spin-dependent scattering of electrons that is field reduced, or spin-polarized tunneling of electrons that is field enhanced, thus strengthening the effect of grain boundaries.     

First-principle study of extrinsic defects in CuScO2 and CuYO2

Using first-principles methods, we studied the extrinsic defects doping in transparent conducting oxides CuMO₂ (MSc, Y). We chose Be, Mg, Ca, Si, Ge, Sn as extrinsic defects to substitute for M and Cu atoms. By systematically calculating the impurity formation energy and transition energy level, we find that BeCu is the most prominent extrinsic donor and CaM is the prominent extrinsic acceptor. In addition, we find that Mg atom substituting for Sc is the most prominent extrinsic acceptor in CuScO₂. Our calculation results are expected to be a guide for preparing n-type and p-type materials through extrinsic doping in CuMO₂ (MSc,Y).