新型金属-多层绝缘介质-金属表面等离子波导结构的传输特性

设计了一种新型金属-多层绝缘介质-金属表面等离子波导结构,利用时域有限差分法对其传输特性进行数值分析。研究了有效折射率和传播长度与中间多层绝缘介质厚度之间的关系,并分析了金属层的角度对该波导结构中场分布的影响。结果表明:当光波从波导结构上方垂直入射时,电磁场被限制在多层介质中的高折射率区,实现了场的耦合传输。多层绝缘介质的厚度均为220 nm时,正六边形金属层结构对应的波导结构的传输性能较为理想。该结构能够实现亚波长尺度的光限制,可以应用于光电子集成和传感器领域。     

非线性介质的表面等离子体波导设计和优化

设计了一种基于非线性介质Si-NC/SiO2的混合表面等离子体波导,利用有限元方法定量分析了这种波导所支持基模的能流密度分布、有效折射率、传播长度和有效面积与几何结构参数以及非线性介质的依赖关系.分析结果表明,光场主要被限制在非线性区域,通过调节非线性层的厚度以及非线性比例因子,可以实现模式的有效折射率和传播长度等传输特性参数的调节.固定非线性介质比例因子,有效折射率和传播距离随非线性层厚度增加而增大;固定波导尺寸,有效折射率随比例因子增大而增大,传播距离和有效面积较小.最后,根据分析结果对非线性效应进行优化,优化后波导最优结构尺寸为波导宽度为250nm,非线性材料层厚度为100nm,硅层厚度为150nm.     

涂覆石墨烯的三根电介质纳米线波导的模式特性

采用多极方法,通过改变工作频率、中间纳米线半径、中间纳米线高度、水平方向上纳米线之间的距离以及石墨烯的费米能,对涂覆石墨烯的三根轴心非共面的电介质纳米线波导所支持的5种低阶模的有效折射率实部和传播长度进行分析。当工作频率从30 THz增加到40 THz时,有效折射率实部增大,传播长度减小。当中间纳米线的半径从20 nm增加到55 nm时,有效折射率的实部增大,传播长度变化各不相同。当中间纳米线的高度从0增加到100 nm时,有效折射率的实部减小,除了模式5外,其他模式的传播长度都增大。当水平方向上纳米线之间的距离从160nm增加到200 nm,石墨烯的费米能从0.4 eV增加到0.8eV时,有效折射率的实部减小,传播长度增大。     

一种由椭圆形金属和介质纳米线组成的混合表面等离子体光波导的基模控制特性研究

本文研究了一种由三根并排放置的椭圆形金属-介质-金属纳米线构成的混合表面等离子体光波导所支持的电磁场基模的控制特性,中间是高折射率的介质纳米线,左右是两根对称放置的金属纳米线。研究结果表明,基模电磁场增强效应主要分布在三根纳米线形成的两个间隙区域,且对整个结构的几何参数有一定依赖性。因此,通过改变纳米线的几何尺寸、两根纳米线之间的间距以及介质的电磁参数,可以调整和控制这种波导所支持的基模的有效折射率、模式传输距离、归一化的模式面积和模式束缚因子等物理特性。基于这些有效的模式操控特性,这种混合型的表面等离子体光波导可以应用于高密度光子器件集成、纳米光子学和生物传感器等领域。     

低损耗超小模面积杂化表面等离激元波导

提出了一种在矩形金属沟槽中插入两块相同的矩形硅核的新型杂化波导结构,基于有限元方法,在波长为1550 nm时,系统地研究了两块介质核间的距离、介质核的高度、宽度以及介质核与金属间的距离对有效模面积和传播距离的影响。计算结果表明,通过左右狭缝或者中间狭缝的场增强效应,能得到低损耗超小模面积的杂化模,当介质核与金属间的距离比较大时,相对于中间无狭缝的情况,当缝隙为5 nm时,该结构的有效模面积急剧减小,约减到原来的七分之一,而传播距离略有增长,在50个波长左右,而且中间缝隙越窄(不等于0 nm),模面积越小,传播距离越大,介质核越高,传播距离越远而模面积几乎不变。当介质核与金属间的距离比较小时,中间缝隙越小,介质核的宽度越小,模面积越小。     

蝴蝶形中空表面等离子体波导的传输特性

本文设计了一种蝴蝶形中空表面等离子体波导,并对其传输特性进行了研究.采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率、传播长度和模式面积随几何参数和工作波长的变化关系进行了分析.结果表明:沿纵向的能流主要分布在由四个圆洞所构成的上下两个尖角之间的区域,且越接近尖角,沿纵向的能流越大.对中空圆洞的半径、上下两排圆洞圆心间横向距离和左右两列圆洞圆心间的纵向距离进行调节,模式的有效折射率、传播长度和模式面积也随之变化.在工作波长确定的条件下,相对于b=r/4的情况来说,当b=r/2时,上下两个尖角之间的距离较大,场与金属的相互作用较弱,有效折射率就较大,传播长度也较大.在几何参数确定的条件下,相对于λ=705.0 nm的情形来说,在λ较大时,场的分布范围较大,场与金属表面的接触面积较大,场与金属的相互作用较弱,有效折射率较小,传播距离较长.与由两个和三个空心圆柱构成芯区的表面等离子体波导相比较,蝴蝶形中空表面等离子体波导具有良好的传输特性.如果在波导结构中心填充增益介质,可以克服较大的传播损耗,因此这种蝴蝶形中空表面等离子体波导可以用于光子器件集成领域和传感器领域.     

领结形中空表面等离子体波导的传输特性

设计了一种领结形中空表面等离子体波导.采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率、传播长度和模式面积随几何结构参数和工作波长的依赖关系进行了分析.结果表明,沿纵向的能流主要分布在两个上下突起所形成的中间区域.通过调整几何参数及工作波长,可以调节模式的有效折射率、传播长度和模式面积.在工作波长确定的条件下,有效折射率随突起半径的增大呈减小趋势,而传播长度和模式面积则随着突起半径的增大呈增大趋势,四个角上的圆弧半径对波导的传输特性有微调作用,左右扇形区域的半径对波导的传输特性有较明显 关键词： 集成光学 光波导 表面等离子体波导     

基于方形谐振器的表面等离子体波导传感器

本文利用方形谐振器与两个金属/介质/金属型波导结构耦合设计了一个亚波长的表面等离子体波导传感器,并通过有限元分析研究了此结构的传输特性。研究表明,通过谐振器耦合能有效增强共振波长的表面等离子体波的透射能力,同时减小两侧波导结构与方形谐振器之间的金属势垒层宽度可提高透射率。传感器的共振波长与介质材料的折射率之间存在着线性关系,1阶共振模的灵敏度可达1100nm/RIU。这种传感器可实现器件的小型化,在生物、工业传感领域有着很大的潜力。     

涂覆石墨烯的电介质纳米并行线的传输特性

设计了一种由涂覆了单层石墨烯的双椭圆电介质纳米并行线构成的表面等离子体光波导,采用有限元方法对其传输特性、电磁参数以及结构参数之间的依赖关系进行了研究。结果表明:随着椭圆的中心距离的增大,有效折射率的实部逐渐减小,传播距离先增大后减小,模式面积逐渐增大;椭圆的半短轴对有效折射率、传播距离和模式面积有微调作用;通过优化计算,减小并行线之间的距离,增加并行线的半短轴的长度,可以达到更好的传输效果;工作频率越高,有效折射率的实部越小,传输距离越短,模式面积越大;温度越高,有效折射率的实部越大,传输距离越短,模式面积越小。研究结果为基于石墨烯材料的表面等离子激元光波导的设计、制作和应用提供了理论基础。     

带有T型腔的MIM波导的法诺共振特性研究

设计了一种带有枝节的金属-介质-金属(MIM)波导与T型谐振腔侧耦合的表面等离子体光波导结构。利用有限元法(FEM),数值分析了改变耦合距离、T型腔几何尺寸及其不对称性、枝节高度对法诺(Fano)共振谱线的影响。结合电磁场分布进一步揭示了Fano共振现象产生的物理机理,由此可以动态调节表面等离子体波在结构中传输时产生的Fano共振特性。另外,研究表明在T型腔内填充不同折射率的材料,利用所设计的波导结构可以实现灵敏度高达940nm/RIU的纳米尺度的折射率传感器。最后研究了结构的慢光传输特性,可以在Fano峰值附近实现约0.025ps的光学延迟。这种新型的表面等离子体光波导可能会在光子器件集成、慢光效应及纳米传感领域有着较大的应用前景。     

双椭圆纳米金属棒构成的表面等离子体波导的传输特性分析

设计了一种双椭圆纳米金属棒表面等离子体波导,采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率和传播长度随几何结构参数和工作波长的依赖关系进行了分析.结果表明,沿纵向的能流主要分布在两个椭圆金属棒所形成的中间区域,且越靠近金属棒的弧形边,沿纵向的能流越大.通过调节两个金属棒的中心距离以及它们的两个半轴的大小,可以调节模式的有效折射率和传播长度.在工作波长确定的条件下,相对于a=b的情形来说,在a<b时,场与金属表面接触的面积较大,场 关键词： 集成光学 光波导 表面等离子体波导     

基于耦合介质纳米线的深亚波长局域波导

提出了一种基于耦合介质纳米线的深亚波长局域波导,通过两根紧邻的高折射率介质纳米线的耦合,该波导可以将光场有效束缚在纳米线之间的低折射率纳米缝隙中. 计算模拟的结果表明,该波导的有效模场面积达到Λ²₀/200,比单根纳米线波导小一个数量级,这种深亚波长的模场束缚能力可以与表面等离激元混合波导相比拟. 计算模拟的结果还表明,纳米线可能带有的低折射率氧化膜、低折射率衬底的存在、以及纳米线间尺寸存在的一定差异对于该波导结构的实际应用都不会产生很大 关键词： 介质波导 亚波长局域 表面等离激元波导 纳米线     

内壁涂覆石墨烯的双椭圆中空表面等离子波导

本文设计了一种内壁涂覆单层石墨烯的双椭圆形中空表面等离子波导,采用有限元的方法对其传输特性进行了研究。结果表明,椭圆之间的距离和半短轴的长度增大时,有效折射率的实部减小,传输距离增大,模式面积减小;圆化半径增大时,有效折射率的实部增大,传输距离减小,模式面积增大;工作频率增大时,有效折射率的实部减小,传输距离减小,模式面积减小;温度升高时,有效折射率先增大后减小,传输距离减小,模式面积减小。本文的工作为研究基于石墨烯的波导器件提供了理论依据。     

Characteristics analysis of hybrid plasmonic waveguide for low-loss lightwave guiding

It has been experimentally demonstrated that a low-loss guided hybrid mode is supported if a metal strip is embedded in a low index polymer layer surrounded by two high index slabs. In this paper, further numerical analyses on the guided hybrid modes are reported to fully elucidate the characteristics of the hybrid plasmonic waveguide. For a one-dimensional slab structure with a metal film of infinite width, simulation results exhibit that low-loss guided hybrid modes are associated with surface plasmon modes and dual dielectric slab modes. The optical properties of the guided modes are improved by increasing the field intensity which is confined into lossless dielectric layers by decreasing the metal film thickness and increasing the refractive index and thickness of the high-index slabs. The finite element method is used to investigate the lateral mode confinement of the optical guided modes by the corresponding metal strip. By reducing the metal film width, the guided modes are confined in the plane transverse to the direction of propagation and the characteristics are significantly improved. The hybrid plasmonic waveguide can be exploited for long-range propagation-based application such as optical interconnection.     

Propagation properties of a modified surface plasmonic waveguide with an arc slot

We introduce a modified surface plasmonic waveguide with an arc slot. The dependences of distribution of energy flux density, effective index, propagation length and mode area of the symmetric mode supported by this waveguide on geometrical parameters and working wavelength are analysed by using the finite-difference frequency-domain (FDFD) method. Results show that the energy flux density distributes mainly in four corners which are formed by two arcs, and the closer to the corners it is, the stronger the energy flux density will be. The effective index, the propagation length and the mode area are influenced by geometrical parameters, including the width, the thickness and the arc radius of the surface plasmonic waveguide, as well as the working wavelength. It has been shown that the surface plasmonic waveguide with an arc slot has better propagation properties than the surface plasmonic waveguide with a straight slot. This work may be helpful for applying the slot surface plasmonic waveguide to integrated photonics.     

Mode characteristics of nested eccentric waveguides constructed by two cylindrical nanowires coated with graphene

A kind of nested eccentric waveguide constructed with two cylindrical nanowires coated with graphene was designed. The mode characteristics of this waveguide were studied using the multipole method. It was found that the three lowest modes (mode 0, mode 1 and mode 2) can be combined by the zero-order mode or/and the first-order modes of two single nanowires. Mode 0 has a higher figure of merit and the best performance among these modes within the parameter range of interest. The mode characteristics can be adjusted by changing the parameters of the waveguide. For example, the propagation length will be increased when the operating wavelength, the minimum spacing between the inner and outer cylinders, the inner cylinder radius and the Fermi energy are increased. However, when the outer cylinder radius, the dielectric constants of region I, or the dielectric constants of region III are increased, the opposite effect can be seen. These results are consistent with the results obtained using the finite element method (FEM). The waveguide structure designed in this paper is easy to fabricate and can be applied to the field of micro/nano sensing.     

All-dielectric bowtie waveguide with deep subwavelength mode confinement

Plasmonic waveguides and conventional dielectric waveguides have favorable characteristics in photonic integrated circuits. Typically, plasmonic waveguides can provide subwavelength mode confinement, as shown by their small mode area, whereas conventional dielectric waveguides guide light with low loss, as shown by their long propagation length. However, the simultaneous achievement of subwavelength mode confinement and low-loss propagation remains limited. In this paper, we propose a novel design of an alldielectric bowtie waveguide, which simultaneously exhibits both subwavelength mode confinement and theoretically lossless propagation. Contrary to traditional dielectric waveguides, where the guidance of light is based on total internal reflection, the principle of the all-dielectric bowtie waveguide is based on the combined use of the conservation of the normal component of the electric displacement and the tangential component of the electric field, such that it can achieve a mode area comparable to its plasmonic counterparts. The mode distribution in the all-dielectric bowtie waveguide can be precisely controlled by manipulating the geometric design. Our work shows that it is possible to achieve extreme light confinement by using dielectric instead of lossy metals.     

Enhancing Bremsstrahlung production from ultraintense laser-solid interactions with front surface structures

A new type of a coaxial multi-layer plasmonic waveguide is proposed. The mode propagation properties are analyzed at the communication working wavelength. Theoretical investigations reveal that the enhanced optical confinement can be achieved in the two low-index dielectric media layers. The mode size can be sub- or deep sub-wavelength scale. The mode propagation loss can be well compensated by replacing the high-index dielectric media with gain material to achieve longer propagation length with better mode confinement. The comparisons of the mode properties between the proposed waveguide and waveguides studied in the published literatures are also considered. These investigations potentially lay the groundwork for the further applications of nanowire type multilayer hybrid structures. This structure could also enable various applications such asnanophotonic waveguides, high-quality nanolasers, and optical trapping and biosensors.     

Asymmetric plasmonic-dielectric coupler with short coupling length, high extinction ratio, and low insertion loss

Asymmetric directional coupling between a hybrid plasmonic waveguide with subwavelength field confinement and a conventional dielectric waveguide is investigated. The proposed hybrid coupler features short coupling length, high coupling efficiency, high extinction ratio, and low insertion loss; it can also be integrated into a silicon-based platform. This coupler can be potentially adopted for signal routing between plasmonic waveguides and dielectric waveguides in photonic integrated circuits. Furthermore, it can be exploited to efficiently excite hybrid plasmonic modes with conventional dielectric modes.     

An efficient directional coupling from dielectric waveguide to hybrid long-range plasmonic waveguide on a silicon platform

The silicon-based three-dimensional hybrid long-range plasmonic waveguide not only supports long-range propagation distance (~mm) but also has an ultra-small modal area (~10^?2 μm²) at 1.55 μm. Here, we propose a directional coupler for effective coupling from a dielectric slab-waveguide to the hybrid plasmonic waveguide on a silicon platform. Our simulation results show that the coupler is able to excite hybrid long-range plasmonic mode with short coupling length, low insertion loss, and high extinction ratio. With the arm separation of 0.3 μm, the coupling length can be made 5.2 % of the propagation length of the hybrid plasmonic waveguide, while the insertion loss and extinction ratio are ?0.12 and 22.4 dB, respectively. This coupler offers the potential applications in signal routing between the hybrid long-range plasmonic waveguide and dielectric waveguide in the photonic integrated circuits.