有损压缩JPEG在载频条纹图分析中的应用研究

探讨了基于JPEG的有损压缩方法在载频条纹图分析中的应用前景。简介了当今流行的JPEG有损压缩技术和傅里叶变换轮廓术。使用专业软件对傅里叶变换轮廓术中拍摄的载频条纹图进行各种压缩比的压缩,解压后再解调出相位,与未经压缩的原图解调出的相位进行比较。将其相位误差与相位移法解调出的相位误差进行了对比,指出相对于相位移法而言,傅里叶变换轮廓术具有滤波的作用,对其拍摄的载频条纹图,应用JPEG压缩算法是可能的,解调出来的相位误差更小。     

一种基于希尔伯特变换实施相移的相位解调算法

相移法因其精度高、运算简单,所以被广泛应用于形貌检测中的相位解调。该方法的弱点是:不仅要采集多幅相移图像,而且不能克服相移器的移相误差。将小波分析与希尔伯特变换结合起来,采用小波分析去除直流背景成分,利用希尔伯特变换方法实现90°相移;利用相移法解调形貌相位,由于是采用软件来实现相移的,因此只需采集一幅变形栅线图。对该方法与传统相移技术进行了模拟比较实验,结果表明,该方法具有较高的精度。     

端元提取技术在高光谱图像压缩中的应用

高光谱图像海量数据如何实现大比例有效压缩是限制其应用的主要问题之一,而现有有损压缩方法存在大压缩比与光谱特性信息准确保留的矛盾,即使现有最优有损压缩方法也不能够得到令人满意的结果。文章基于混合像元分解的思想提出基于端元提取技术的数据有损压缩方法来解决该矛盾,首先用顶点成分分析(VCA)方法提取场景中地物的端元光谱,根据各端元与观测像元之间的光谱间余弦角相似性度量方法估计各端元的丰度,接着对端元光谱及丰度数据进行无损压缩,最后利用JPEG2000有损压缩方法对高光谱图像的所有单波段图像进行空间维大比例有损压缩。AVIRIS高光谱图像的仿真结果表明,压缩比得到大幅度提高,光谱信息得到有效恢复。在实现压缩比为50∶1时,大部分像元的光谱角误差在2%左右。     

投影条纹相移法中图像饱和误差抑制算法研究

针对投影条纹相移法三维形貌测量中的图像饱和误差进行了深入研究,分析了基于条纹相移技术的图像饱和误差抑制算法的适用范围,推导了基于六步相移的饱和误差抑制算法公式.理论分析表明,相移条纹图的帧数越多,饱和误差抑制算法的适用范围越广.并通过数值模拟和实验进行了验证,基于六步相移的饱和误差抑制算法可以更加有效地抑制图像饱和引起的相位误差.     

投影条纹相移法中图像饱和误差抑制算法研究

针对投影条纹相移法三维形貌测量中的图像饱和误差进行了深入研究,分析了基于条纹相移技术的图像饱和误差抑制算法的适用范围,推导了基于六步相移的饱和误差抑制算法公式.理论分析表明,相移条纹图的帧数越多,饱和误差抑制算法的适用范围越广.并通过数值模拟和实验进行了验证,基于六步相移的饱和误差抑制算法可以更加有效地抑制图像饱和引起的相位误差.     

基于条纹级次编码与调制的结构光相位展开算法

利用相位级次的编码和调制方法将相位级次信息叠加到相移图像中,提出了一种直接利用相移图像进行相位解包裹的方法。在投影端,提出了一种邻接不重复德布鲁因序列,并用该序列对相位级次进行编码,然后将该周期级次编码序列调制、叠加到多步相移图像中。相应地,在解码阶段,从拍摄到的相移图像中同时解调、分解出包裹相位和周期级次编码序列,通过序列的匹配还原真实周期级次信息,并最终准确地解包裹出绝对相位。以四步相移法为例,本文方法相比传统的时间相位解包裹算法,投影图片从10张(64个相位周期)缩减到了4张,提高了测量效率。     

JPEG图像压缩对测量类图像的影响

在JPEG图像压缩的量化过程中,丢弃了部分高频信息,使图像的清晰度下降。通过对频谱的对照分析和对实际图像进行实验后表明,JPEG图像压缩对测量和处理结果的影响与原图像的特点、取样方式、滤波过程和压缩算法有关。经摄像机和图像卡获得的图像,其压缩比可达到10;经扫描仪获得的图像,其压缩比可达到6;经数码相机获得的图像,其压缩比可达到6～8;对特定的医学图像、晶相图像等来说,利用图像的特征构造最优匹配的JPEG压缩量化表,其压缩比可达到10。采用合适的压缩比和改进的压缩方法,图像的细节损失可以控制在较小的范围内,基本上不影响检测类图像的边界提取、分割、尺寸测量时的处理结果。     

相移阴影莫尔条纹正交化解调技术

提出一种基于克莱姆正则化分析法的三帧自标定相移阴影莫尔三维轮廓技术.该技术首先采用移动光栅的方法获得相移条纹图,然后通过不同帧相移条纹图相减去除条纹图背景,进而结合克莱姆正交化法和最小二乘法,发展了一种相位解调方法,提取了测量相位.以五步Harlharan算法为参考,用不同算法对同一物体表面进行测量.结果表明,相对于典型的三步相移法和主量分析方法,提出的方法测量得到的相位误差最小(0.5rad),且简化了测量过程.     

基于概率密度函数的彩色相位测量轮廓术校正

在彩色相位测量轮廓术中,光电器件多个光通道之间的颜色串扰、强度响应不均等因素的影响,使得所获取的相移条纹图像失真,因此采用传统的相位技术求解相位会产生极大的相位误差。从彩色条纹图像的数学模型出发,分析了彩色成像器件所获取的红绿蓝三通道条纹图像特性,提出一种两步校正方法：第一步是基于三通道均值及标准差实现对各颜色通道图像强度的归一化处理;第二步是使用概率密度函数曲线搜索失真后的实际相移量,抑制相移量不准确对测量结果的影响。所提方法不需要对系统的耦合系数和相移偏移量进行预校正,可实现简便、快速的相位误差补偿。模拟及实验结果验证了该方法的有效性。     

阴影叠栅相移非线性误差补偿算法研究

相移阴影叠栅干涉场的相位(高度)存在非线性关系,而传统的相移阴影叠栅技术往往忽略了相位与高度的非线性关系,从而在测量系统中引入测量误差。对此提出了一种基于迭代相位解调自调算法相移阴影叠栅技术,该方法利用最小二乘技术获得相移量估算值,利用该估算值通过迭代算法消除相移阴影叠栅的全场相位误差,从而得到正确的相位分布。模拟计算表明该方法可以有效解决相移不均产生的相位测量误差问题,且可实现光栅移动量的精确估算,其误差不超过3.4%。对比实验进一步说明了所提出方法的正确性和优越性。     

Rapid phase extraction method based on the difference image between interferograms with unknown phase-shifting amount

In phase-shifting interferometry, based on the difference image between interferograms with unknown phase-shifting amount, a rapid phase extraction method is proposed. In this method, first, by means of the simple subtraction operation between interferograms captured in one phase-shifting period, a sequence of difference images are generated easily; second, to decrease the random phase-shifting errors induced during the phase-shifting procedure, the summation operation is performed for these difference images; third, based on one time phase recovery operation and one time phase-unwrapping operation, the measured phase with high precision can be obtained rapidly. Moreover, in the proposed method, by means of a simple phase summation operation for all pixel-phases in one interferogram, the corresponding phase-shifting amount of interferogram can be determined conveniently.     

A composite-structured-light 3D measurement method based on fringe parameter calibration

This paper proposes a novel method for reducing measurement error caused by spectrum overlapping in composite-structured-light 3D measurement systems. For a composite-structured-light 3D measurement system, spectrum overlapping causes parameters of each deformed phase-shifting fringe to change, and therefore leads to phase measurement errors. The proposed fringe parameter calibration method is based on the fact that variations in each deformed fringe's parameters are independent of height and reflectivity of the measured object. Three frames of composite grating are projected on the reference plane, and each carrier channel includes the information of three phase-shifting sinusoidal gratings used in Phase Measuring Profilometry (PMP). With the parameter calculation formulas of PMP, the parameters of fringes demodulated from the same carrier channel can be calculated, and therefore parameter relation coefficients between fringes demodulated from different carrier channels may be obtained. When an object is measured, these relation coefficients can be used to calibrate the parameters of the deformed phase-shifting fringes. A new 3D measurement mathematical model is established to reconstruct the shape of the object. Experimental data proved that the proposed method can effectively restrain the effect of spectrum overlapping and improve measurement accuracy by more than three times.     

A demodulation method for the circular carrier interferogram using phase stitching

The four phases stitching algorithm is proposed to demodulate the circular carrier interferogram, which can eliminate the sign ambiguity and avoid serious local errors in the Fourier transform method. A pair of orthogonal low-pass filters is used to obtain four demodulated phases with local errors concentrated in different areas, then their reliable parts are chosen and combined to get the phase without sign ambiguity by a stitching strategy, which makes a significant error suppression. Furthermore, due to the stitching strategy the sign flip location just needs to be detected approximately, therefore the detection can be done using an automatic procedure. The algorithm is validated by the numerical simulations, where the calculation precisions are better than λ/50 with suitable carrier. Besides, an actual interferogram is analyzed and the result is in good accordance with the Zygo phase-shifting interferometer.     

基于背景光调制的复合光傅里叶变换轮廓术

提出一种基于背景光调制的用于傅里叶变换轮廓术测量范围的复合光栅,该光栅通过调制一正弦条纹和不含任何相位信息的背景光来抑制零频,较基于相移技术的复合光栅有更大的优势:背景光只含直流分量,使得复合光栅的频谱更加简单,有利于滤出载波信息,提高测量精度;对从复合光栅中解调出来的背景光只涉及平均值校准,校准过程更为简单;解调出的背景光与物体表面的反射率成正比,具有潜在的应用价值。采用Matlab程序对该复合光栅进行了数值模拟,并对该光栅实用性进行了实验研究,结果证实了该光栅用于抑制零频、扩大傅里叶变换轮廓术测量范围的有效性,且提高了测量精度。     

Shifted-phase calibration for a 3-D shape measurement system based on orthogonal composite grating projection

This paper proposes a novel method for reducing measurement error caused by spectrum overlapping in orthogonal-composite-grating-based 3-D measurement method. For 3-D measurement systems based on orthogonal composite grating projection, spectrum overlapping causes phase of each deformed phase-shifting fringe changed differently, which violates the principle that the shifted phases between adjacent deformed fringes must be equivalent to 2π/3, and therefore results in phase measurement error. The proposed shifted-phase calibration method is based on that phase variation of each deformed fringe is independent of height and reflectivity of the measured object. Three composite gratings are projected on the reference plane, and each carrier channel includes three phase-shifting gratings needed in phase measuring profilometry (PMP). Because the adjacent phase-shifting fringes demodulated from the same carrier channel have the phase difference of 2π/3, we can respectively calculate the reference plane's phases of three carrier channels by the phase algorithm of PMP method, and the shifted phases between them are obtained. When an object is measured, the shifted phases between deformed phase-shifting fringes can be calibrated. A new 3-D measurement mathematical model is set to reconstruct object. Our experiments prove that the proposed method can effectively restrain the effect of spectrum overlapping and improve measurement accuracy almost one times.     

Optical image encryption using chaos-based compressed sensing and phase-shifting interference in fractional wavelet domain

In this paper, a novel optical image encryption system combining compressed sensing with phase-shifting interference in fractional wavelet domain is proposed. To improve the encryption efficiency, the volume data of original image are decreased by compressed sensing. Then the compacted image is encoded through double random phase encoding in asymmetric fractional wavelet domain. In the encryption system, three pseudo-random sequences, generated by three-dimensional chaos map, are used as the measurement matrix of compressed sensing and two random-phase masks in the asymmetric fractional wavelet transform. It not only simplifies the keys to storage and transmission, but also enhances our cryptosystem nonlinearity to resist some common attacks. Further, holograms make our cryptosystem be immune to noises and occlusion attacks, which are obtained by two-step-only quadrature phase-shifting interference. And the compression and encryption can be achieved in the final result simultaneously. Numerical experiments have verified the security and validity of the proposed algorithm.     

Image encryption based on gyrator transform and two-step phase-shifting interferometry

A novel optical image encryption method is proposed, based on gyrator transform and phase-shifting interferometry. The input two-dimensional image to be encrypted is gyrator transformed two times, and two random phase masks are placed at the input plane and the output plane of the first gyrator transform. Two-step phase-shifting interferometry is used to record the digital holograms of the input image encrypted by use of double-random phase encoding technique in gyrator transform domain. The rotation angles of gyrator transform, the random phase mask in the gyrator plane and the arbitrary phase shift used for recording form the keys for decryption of the input image. Numerical simulations are presented to verify its validity and efficiency.     

菲索干涉仪中精确移相的实现

为了实现移相式菲索干涉仪对光学元件面形的高精度测量,建立了干涉仪同步采集移相系统,并对精确移相方法进行了研究。介绍了移相系统的构成和工作原理,计算了测量过程中移相器的速度。针对PZT移相器在移相过程中会引入离焦误差,并存在加速段和减速段的问题,详细设计了移相器的行进过程。最后,对移相器的性能进行了标定。在改造后的干涉仪上开展了重复性验证实验,结果表明：干涉仪可以获得λ/11 340的RMS测量重复性。对改造后干涉仪与Zygo公司生产的Verifire XP/D干涉仪的测量精度做了比对实验,结果显示：相同元件下两者测量结果的面形RMS之差约为0.9 nm,表明提出的移相系统及移相方法在重复性和准确度方面都能满足纳米级面形测量的要求,为研制高精度移相干涉仪奠定了基础。     

Conversion from phase map to coordinate: Comparison among spatial carrier, Fourier transform, and phase shifting methods

For full-field phase measurement methods, many algorithms have been developed to extract a phase map from fringe image(s). Both phase wrapping and unwrapping algorithms have been extensively investigated by many researchers, but few papers can be found on how to calculate the coordinates of surface points from a phase map. This paper focuses on algorithms that show how a phase map can be used to calculate coordinates. Details are given for single image methods such as Fourier transform, spatial carrier methods, and multiple image methods like traditional phase-shifting methods. Algorithms that can be used to convert a phase map to coordinates and some issues related to these conversion algorithms are discussed. An artifact is measured using these phase measurement methods. The results show that using the correct algorithm to convert a phase map to coordinates is a key to obtaining accurate measurement results.