GaN基白光LED的结温测量

用正向电压法、管脚法和蓝白比法等三种方法测量GaN基白光LED的结温,获得了较为准确的结温,误差可以控制在4℃以内.正向电压法在恒定电流的条件下,得到了正向电压与结温的线性关系;蓝白比法在不同环境温度和不同注入电流两种情况下,都得到了蓝白比与结温较好的线性关系.提出了蓝白比法可能的物理机制,提高环境温度和增大注入电流都会使结温升高,蓝光峰值波长也会改变,这两个因素都会影响荧光粉的激发和发光效率.降低结温需要考虑的主要因素有白光LED的接触电阻、串联电阻和外量子效率,封装材料的热导率,反射杯和管脚的设计,以及空气散热部分的散热面积等.     

LED结温与光谱特性关系的测量

采用恒定驱动电流改变环境温度和恒定环境温度改变驱动电流两种方法分别对直径5 mm封装的AlGaInP型红光和黄光LED,InGaN型绿光和蓝光LED,以及InGaN蓝光+荧光粉的白光LED的结温与其光谱特性进行了测量,得到了不同条件下LED结温与光谱特性的关系.结果表明;AlGaInP LED的峰值波长与结温有良好线性关系,InGaN LED的峰值波长则与结温没有明显对应关系;但白光LED发射光谱的白、蓝功率比与结温有良好线性关系;对AlGaInP LED及蓝光激发的白光LED,通过光谱特性测量可快速、准确地确定光源系统中各LED的结温继而预测光源系统的有效寿命.     

LED结温与光谱特性关系的测量

采用恒定驱动电流改变环境温度和恒定环境温度改变驱动电流两种方法分别对直径5 mm封装的AlGaInP型红光和黄光LED,InGaN型绿光和蓝光LED,以及InGaN蓝光+荧光粉的白光LED的结温与其光谱特性进行了测量,得到了不同条件下LED结温与光谱特性的关系.结果表明;AlGaInP LED的峰值波长与结温有良好线性关系,InGaN LED的峰值波长则与结温没有明显对应关系;但白光LED发射光谱的白、蓝功率比与结温有良好线性关系;对AlGaInP LED及蓝光激发的白光LED,通过光谱特性测量可快速、准确地确定光源系统中各LED的结温继而预测光源系统的有效寿命.     

基于特征光谱参量表征发光二极管结温的方法

针对采用蓝光激发荧光粉产生白光的YAG型白光LED,通过分析其光谱波谷特性,采用常规可见光光谱仪和温控系统设计了一套基于光谱特征参量的LED结温测试系统.测量方法分为定标函数的测定和任意状态下的测量两部分.首先采用光谱仪测量在给定的多个不同结温和正常驱动电流下的相对发光光谱数据,再分析其光谱波谷处的相对光谱强度.从实用性和降低成本的角度考虑,采用正常工作电流驱动,但以正常工作电流驱动下的LED在光谱仪的固定反应时间内其自加热效应不可忽略.因此采用选定基准状态法,将各温度下的相对发光光谱强度与基准状态下的逐点作差得到相应的发光光谱强度差,同时为了减少温控系统引入的温度偏差,同样将各温度与基准温度作差得到相应的结温差.实验表明高低色温大功率LED的结温差和发光光谱强度差经过一定的函数拟合形成的定标函数其线性度都较高,R2达到0.99以上;利用定标函数,可以测量出在任意状态下的LED结温.最后将采用本方法得出的高低色温LED在不同条件下的结温数据与通过Mentor Graphics公司的T3Ster仪器的测量结果进行了比较,最大偏离度为2.82%,在可接受的误差范围内,表明此方法完全具备可行性,具有一定的实用价值.     

Si衬底GaN基LED的结温特性

结温是发光二极管的重要参数之一,它对器件的内量子效率、输出功率、可靠性及LED的其他一些性能有很大的影响。首次报道Si衬底GaN基LED的结温特性。利用正向压降法测量Si衬底上GaN基LED的结温,通过与蓝宝石衬底上GaNLED的结温比较,发现Si衬底GaNLED有更低的结温,原因归结为Si有更好的导热性。同时也表明:用Si作GaNLED的衬底在大功率LED方面具有更大的应用潜力。     

基于相对光谱强度的非接触式LED结温测量法

基于一体化封装高导热铝板,利用蓝光芯片及常用YAG荧光粉,制备了大功率白光LED,并研究了其在不同结温下的光谱变化规律。发现白光LED辐射光谱在波长485 nm处辐射强度具有极小值,并且此波长的辐射强度与LED结温存在良好的线性关系,以此为依据给出了该波长辐射强度与结温的关系公式,测量了LED结温,并与正向压降法及光谱法的测量结果进行对比。实验结果显示：所提出的结温测量方法与正向压降法测量结果差距不超过2 ℃,该方法保持了正向压降法的结温测量较为准确的优点,克服了光谱法的光谱漂移过小,对测试结果带来较大误差的缺点,同样也具有光谱法的实用性强、高效直观、非接触测量、不破坏灯具结构的优点。     

大功率GaN基发光二极管等效串联电阻的功率耗散及其对发光效率的影响

由于自加热效应的存在，大功率GaN基发光二极管(LED)的芯片温度有可能高出环境温度很多，实验中，芯片温度超出环境高达147 K.从实验测量的大功率LED电流电压特性曲线中，将p-n结和等效串联电阻上的电压降落分离出来，得到了大功率LED等效串联电阻随芯片温度的变化情况.在输入电功率自加热效应的影响下，大功率GaN基LED等效串联电阻呈现出剧烈的变化，其阻值由低输入功率时的1.2 Ω降低到0.9 Ω,然后再升高到1.9 Ω，等效串联电阻的功率耗散在输入功率中所占的比例也随着输入功率的增加迅速增加，最高时接     

结温对高压白光LED光谱特性的影响

高压LED因其自身突出的特点在照明领域有着潜在的应用优势,但作为一种新型功率LED,其光电热特性仍需深入研究。该实验对6和9V GaN基高压LED芯片进行了相同结构和工艺条件的封装,对封装样品进行了10~70℃的变温度光谱测试,并进行了从控温平台温度到器件结温的转换。为保证器件的电流密度相同,6和9V样品光谱测试的工作电流分别设定为150和100mA。结果显示,结温升高会导致蓝光峰值波长红移、波长半高宽增大、光效下降和显色指数上升等现象。在相同平台温度和注入功率下,9V样品的结温低于6V样品;随着温度的升高,9V样品波长半高宽的增加量比6V样品少1.3nm,光效下降量少1.13lm·W~(-1),显色指数上升量少0.28。以上表明,与低压LED相比,高压LED有着更低的工作结温和更小的温度影响。原因在于,相同环境温度下高压LED具有更好的电流扩展性和更少的发热量。此特性在高压LED的研究、发展与应用等方面具有参考价值。此外,峰值波长仍与结温有着较好的线性度,在光谱设备精度较高的情况下可继续作为结温的敏感参数。     

InGaN基白光LED光谱特征和结温相关性研究

 以InGaN蓝光+荧光粉的白光LED为研究对象,在恒定环境温度下改变驱动电流,利用光谱仪测得不同LED结温下的光谱曲线。通过分析实验数据,得出光谱特征与该型LED结温的关系。结果表明：InGaN基白光LED蓝光和荧光的峰值波长与结温没有明显的线性关系;蓝光的光谱线宽以及荧光和蓝光峰值强度的比值与结温具有良好的线性关系。     

大功率GaN基发光二极管等效串联电阻的功率耗散及其对发光效率的影响

由于自加热效应的存在,大功率GaN基发光二极管(LED)的芯片温度有可能高出环境温度很多,实验中,芯片温度超出环境高达147 K.从实验测量的大功率LED电流电压特性曲线中,将p-n结和等效串联电阻上的电压降落分离出来,得到了大功率LED等效串联电阻随芯片温度的变化情况.在输入电功率自加热效应的影响下,大功率GaN基LED等效串联电阻呈现出剧烈的变化,其阻值由低输入功率时的1.2 Ω降低到0.9 Ω,然后再升高到1.9 Ω,等效串联电阻的功率耗散在输入功率中所占的比例也随着输入功率的增加迅速增加,最高时接 关键词： 自加热 等效串联电阻 发光二极管 流明效率     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.