Frequency and power dependence of ultrasonic degassing

We investigated the time variation of ultrasonic degassing for air-saturated water and degassed water with a sample volume of 100 mL at frequencies of 22, 43, 129, 209, 305, 400, 514, 1018, and 1960 kHz and ultrasonic power of 15 W. Ultrasonic degassing was evaluated by dissolved oxygen concentration. Ultrasonic degassing was also investigated at a frequency of 1018 kHz and ultrasonic powers of 5, 10, 15, and 20 W. The dissolved oxygen concentration varied with the ultrasonic irradiation time and became constant after prolonged ultrasonic irradiation. The constant dissolved oxygen concentration value depended on the frequency and ultrasonic power but not the initial dissolved oxygen concentration. The degassing rate at 101.3 kPa was higher in the frequency range of 200 kHz to 1 MHz. The frequency dependence of the degassing rate was almost the same as that of the sonochemical efficiency obtained by the potassium iodide (KI) method. Ultrasonic degassing in the frequency range of 22–1960 kHz was also investigated under reduced pressure of 5 kPa. Degassing was accelerated when ultrasonic irradiation was applied under reduced pressure. However, under a reduced pressure of 5 kPa, the lower the frequencies, the higher is the degassing rate. The sonochemical reaction rate was examined by the KI method for varying dissolved air concentrations before ultrasonic irradiation. Cavitation did not occur when the initial dissolved oxygen concentration was less than 2 mg·L⁻¹. Therefore, the lower limit of ultrasonic degassing under 101.3 kPa equals 2 mg·L⁻¹ dissolved oxygen concentration. A model equation for the time variation of dissolved oxygen concentration due to ultrasonic irradiation was developed, and the degassing mechanism was discussed.     

The role of ultrasound in hydrogen removal and microstructure refinement by ultrasonic argon degassing process

In this work, the role of ultrasound in hydrogen removal and microstructure refinement by the ultrasonic argon degassing has been fully investigated by the experimental work in water and AZ91-0.4Ca magnesium melt, respectively. Ultrasound is able to break up argon gas into numbers of small bubbles and drive them diving deeply to the bottom of water, which are responsible for the efficient degassing regime of ultrasonic argon process. The argon flowrate plays a dominant role in promoting hydrogen removal effect. Meanwhile, the increasing argon flowrate can suppress the microstructure refinement, due to the subdued ultrasonic cavitation under a large argon flowrate. Mechanical properties of AZ91-0.4Ca alloy can be much promoted by the ultrasonic argon degassing process. Ultrasound is the key to achieve not only efficient degassing regime, but also microstructure refinement as well as mechanical properties promotion.     

氢在HR－1不锈钢中迁移特性的热动力方法研究

本文研究了氢在ＨＲ－１不锈钢中热动力驱动的宏观迁移特性。用不同的方法（电化学方法和１０５ｐａ氢压强下高温气相法）使试样充氢，然后研究加热升温放气规律，得到了在有意义的温度范围内出气峰的位置以及氢在ＨＲ－１材料中扩散、溶解、渗透系数与温度的关系，并与渗透法测得的结果和国外类似实验结果符合得较好。这些数据对估计未来聚变堆中氚的投料量和氚的渗透漏失有实际意义。     

The influence of air content in water on ultrasonic cavitation field

Cavitation is a complex physical phenomenon affected by many factors, one of which is the gas dissolved in the medium. Researchers have given some efforts to the influence of gas content on sonoluminescence or some specific chemical reactions in and around the bubble, but limited work has been reported about the influence on the ultrasonic cavitation field distribution. In this work, the intensity distribution of the ultrasound field in a cleaning tank has been measured with the hydrophone. After analysed and visualised by MATLAB software, it was found that the cavitation intensity distribution in degassed water was much better than that in tap water. And further study proved that degassing process can improve the cavitation effect dramatically both in intensity and scope. Finally, the cavitation fields in mediums with different gas content were measured and the specific influence of air content on cavitation field was discussed.     

Bubble population phenomena in acoustic cavitation

Theoretical treatments of the dynamics of a single bubble in a pressure field have been undertaken for many decades. Although there is still scope for progress, there now exists a solid theoretical basis for the dynamics of a single bubble. This has enabled useful classifications to be established, including the distinction between stable cavitation (where a bubble pulsates for many cycles) and transient cavitation (where the bubble grows extensively over time-scales of the order of the acoustic cycle, and then undergoes an energetic collapse and subsequent rebound and then, potentially, either fragmentation, decaying oscillation or a repeat performance). Departures from sphericity, such as shape and surface oscillations and jetting, have also been characterized. However, in most practical systems involving high-energy cavitation (such as those involving sonochemical, biological and erosive effects), the bubbles do not behave as the isolated entities modelled by this single-bubble theory: the cavitational effect may be dominated by the characteristics of the entire bubble population, which may influence, and be influenced by, the sound field.

The well established concepts that have resulted from the single-bubble theory must be reinterpreted in teh light of the bubble population, an appreciation of population mechanisms being necessary to apply our understanding of single-bubble theory to many practical applications of ‘power’ ultrasound. Even at a most basic level these single-bubble theories describe the response of the bubble to the local sound field at the position of the bubble, and that pressure field will be influenced by the way sound is scattered by neighbouring bubbles. The influence of the bubble population will often go further, a non-uniform sound field creating an inhomogeneous bubble distribution. Such a distribution can scatter, channel and focus ultrasonic beams, can acoustically shield regions of the sample, and elsewhere localize the cavitational activity to discrete ‘hot spots’. As a result, portions of the sample may undergo intense sonochemical activity, degassing, erosion, etc., whilst other areas remain relatively unaffected. Techniques exist to control such situations where they are desirable, and to eliminate this localization where a more uniform treatment of the sample is desired.     

Magma degassing during eruption through water-saturated porous rocks

In the case of extrusive eruption, we consider the problem on magma degassing which rises in a volcano conduit crossing porous water-saturated rocks. We show that the intensity of outflow of volcanic gases into the rocks is comparable to the intensity of their transport with the rising magma. The magma degassing in the rocks substantially affects the eruption dynamics, in particular, the duration of the periods of eruptive activity.     

Comparison of frequency domain and time domain methods for the numerical simulation of contactless ultrasonic cavitation

The use of a top-mounted electromagnetic induction coil has been demonstrated as a contactless alternative to traditional ultrasonic treatment (UST) techniques that use an immersed mechanical sonotrode for the treatment of metals in the liquid state. This method offers similar benefits to existing UST approaches, including degassing, grain refinement, and dispersion of nanoparticles, while also preventing contact contamination due to erosion of the sonotrode. Contactless treatment potentially extends UST to high temperature or reactive melts. Generally, the method relies on acoustic resonance to reach pressure levels suitable for inertial cavitation and as a result the active cavitation volume tends to lie deep in the melt rather than in the small volume surrounding the immersed sonotrode probe. Consequently, (i) with suitable tuning of the coil supply frequency for resonance, the treatment volume can be made arbitrarily large, (ii) the problem of shielding and pressure wave attenuation suffered by the immersed sonotrode is avoided. However, relying on acoustic resonance presents problems: (i) the emergence of bubbles alters the speed of sound, resonance is momentarily lost, and cavitation becomes intermittent, (ii) as sound waves travel through and reflect on all the materials surrounding the melt, the sound characteristics of the crucible and supporting structures need to be carefully considered. The physics of cavitation coupled with this intermittent behaviour poses a challenge to sonotrode modelling orthodoxy, a problem we are trying to address in this publication. Two alternative approaches will be discussed, one of which is in the time domain and one in the frequency domain, which couple the solution of a bubble dynamics solver with that of an acoustics solver, to give an accurate prediction of the acoustic pressure generated by the induction coil. The time domain solver uses a novel algorithm to improve simulation time, by detecting an imminent bubble collapse and prescribing its subsequent behaviour, rather than directly solving a region that would normally require extremely small time steps. This way, it is shown to predict intermittent cavitation. The frequency domain solver for the first time couples the nonlinear Helmholtz model used for studying cavitation, with a background source term for the contribution of Lorentz forces. It predicts comparable RMS pressures to the time domain solver, but not the intermittent behaviour due to the underlying harmonic assumption. As further validation, the frequency domain method is also used to compare the generated acoustic pressure with that of traditional UST using a mechanical sonotrode.     

On removal of impurities from water by acoustic pulses

Water degassing and removal of salts by high-power acoustic pulses are analyzed. A model explaining the mechanisms of these processes is proposed.     

超声清洗装置空化噪声谱分析法空化噪声级测量

空化强度是用以衡量液体介质中空化活动的剧烈程度,同时空化效应在超声清洗中起关键作用,因此,测量超声清洗槽中的空化强度便可了解其中空化活动的情况。当发生空化时,液体介质中会产生成分复杂空化噪声,对空化噪声谱进行分析和计算得到空化噪声级,据此可判断空化强度。实验测得结果表明：超声清洗装置内稳态空化分布广泛、均匀,瞬态空化分布集中;超声清洗槽内稳态空化与瞬态空化都分布均匀。空化噪声级空间平均可以较好地表示超声清洗槽声场环境中的整体空化强度;但对于超声清洗装置声场环境,空化噪声级空间平均可以表示稳态空化强度,而瞬态空化强度的测量需要在发生瞬态空化的区域测量。     

电子敏感CMOS部件除气方法北大核心CSCD

电子轰击有源像素传感器(electron bombarded active pixel sensor,EBAPS)作为真空-固体混合型微光器件,其性能和工作寿命一定程度上取决于器件内部真空度保持情况。分析造成EBAPS器件真空度下降的原因,推断出真空度恶化的严重后果,提出提高和保持EBAPS器件内部真空度的手段,通过搭建超高真空除气系统对EBAPS器件中核心部件电子敏感CMOS部件的放气特性进行了研究,并根据研究结果得到最佳的除气工艺参数,为EBAPS数字化微光器件的制备提供了技术基础。