Ag负载WO3/TiO2光催化剂的合成及其催化性能

以钛酸丁酯、无水乙醇、钨酸铵为原料,采用溶胶-凝胶法合成了WO3/TiO2复合光催化剂;采用光还原技术制备了Ag负载WO3/TiO2光催化剂,借助X射线粉末衍射(XRD)和UV-Vis光谱等技术对样品的组成和光吸收性能进行了表征,并以罗丹明B为模型污染物考察样品的光催化活性。XRD分析表明,所得粉体均为锐钛矿型纳米TiO2,且与WO3复合后,纳米TiO2特征衍射峰宽化,强度降低;UV-Vis光谱分析表明,载银使得催化剂在400—700nm的可见光区域对光响应,且在紫外光区吸收显著增强,对光具有更高的利用率;以罗丹明B为降解物的光催化实验表明,WO3复合对纳米TiO2光催化活性有显著的影响,而载Ag后其光催化活性进一步提高,将该光催化剂用于炼油厂废水的处理,效果较好。     

纳米金红石TiO2光催化剂的水解合成及其性能

采用水解法在323K制备了比表面积较大的纳米金红石TiO2光催化剂,并通过X射线衍射(XRD)、BET比表面积测试法、紫外-可见吸收光谱(UV-Vis)、红外光谱(IR)和光电化学(PEC)测量对纳米光催化剂进行了表征。以甲基橙为光催化反应的模型化合物,在比表面积相近的条件下,对纳米金红石和锐钛矿TiO2光催化剂的光催化活性进行了评价。光催化实验结果表明:比表面积为～95m2.g-1时,比表面积相近的金红石和锐钛矿的紫外光催化活性相当,但金红石的可见光催化活性明显高于锐钛矿的可见光催化活性。光电化学实验表明:在紫外光照射下催化剂的光电流密度从弱到强的顺序与其紫外光催化活性从低到高的次序一致。     

超声喷雾热解法制备氮掺杂纳米TiO_2薄膜及其光催化特性研究

利用超声喷雾热解法在玻璃衬底上制备了不同沉积温度下的氮掺杂纳米TiO2薄膜,并525℃的退火处理.通过SEM,XRD和UV-Vis透过光谱等表征手段研究了TiO2薄膜表面形貌、结构特性和光催化特性,并探讨了掺杂作用机理.SEM结果表明,在400℃温度下掺N(原子数分数4%)的TiO2薄膜表面比较均匀,致密性好;XRD分析得出,该薄膜是多晶锐钛矿结构;UV-Vis透过光谱分析得出,该薄膜在可见光区的平均透过率为82%,吸收边红移77 nm,计算得知其禁带宽度变小.在紫外光的照射下,氮掺TiO2薄膜对亚甲基蓝溶液具有良好的光催化降解作用,降解率可达46.6%.     

Eu和N共掺TiO_2的结构及光催化性能研究

本文基于第一性原理的平面波超软赝势计算TiO2和Eu-N-TiO2的几何结构、重叠布局数、Mulliken电荷、能带结构、态密度、电荷分布和光吸收.研究发现Eu和N共掺后有额外电子进入价带,使费米面上移且态密度变平缓,有利于载流子的产生和运输.共掺后产生了离子性更强的化学键,能吸收波长较长的光,并且禁带宽度降低,发生红移,提高了TiO2的光催化活性.同时采用了溶胶-凝胶法制备TiO2和Eu-N-TiO2复合纳米材料,对其进行XRD、UV-vis和SEM表征,并通过光降解甲基橙评估其光催化活性.研究发现Eu和N共掺能抑制TiO2从锐钛矿相向金红石相转变和晶粒长大,有利于提高TiO2的光催化活性.此外,Eu-N-TiO2在250nm后的紫外光和可见光下的光催化活性都比TiO2高,经过2个小时照射,在紫外光和可见光下对甲基橙的光降解率分别达到98.54%和69.59%.     

AgNbO_3/石墨烯复合材料的合成及其可见光催化甲基橙降解活性（英文）

采用固相法合成AgNbO_3/石墨烯复合纳米材料,利用透射电子显微镜(TEM)及紫外-可见漫反射光谱(UV-Vis)对样品的形貌及光学性质进行了表征。研究发现,AgNbO_3与石墨烯复合后,带隙能明显降低,吸收光波长范围增大。以甲基橙溶液的降解为光催化模型反应评价了AgNbO_3/石墨烯复合纳米材料的可见光催化性能。结果表明:与纯AgNbO_3相比,AgNbO_3/石墨烯复合纳米材料对甲基橙的可见光催化性能明显增强。实验条件下,经300℃煅烧的AgNbO_3/石墨烯(2∶1)复合纳米材料表现出最优的催化性能,它对甲基橙的可见光催化脱色速率系数约为纯AgNbO_3的10倍。光催化降解机理研究表明,促使甲基橙降解脱色的主要活性物种为·O_2~-和h+。     

La-Ce-TiO_2纳米光催化剂的溶胶-微波法合成、谱学表征及其活性研究

以钛酸四丁酯为原料,采用溶胶-微波法(Sol-Microwave Method)合成了镧和铈共掺型纳米TiO2粉体(La-Ce-TiO2),借助XRD、XPS和UV-Vis等测试手段对其进行了表征,并以甲基橙为模型污染物考察了掺杂量对样品光催化活性的影响规律.XRD分析表明,所得粉体均为锐钛矿相纳米TiO2,且稀土元素镧和铈掺杂后纳米TiO2特征衍射峰宽化,强度降低;XPS分析表明,镧和铈掺杂后样品表面存在大量的氧缺位;UV-Vis吸收光谱表明,所得粉体在400 nm以下均有连续宽化的吸收带,且La和Ce掺杂后样品对光的吸收显著增强,这足由于La(Ⅲ)-O荷移跃迁以及Ce(Ⅳ)f→d跃迁和Ce(Ⅳ)-O荷移跃迁所致;光催化实验表明,La和Ce共掺杂能显著提高纳米TiO2的光催化活性,其中当La(Ⅲ)和Ce(Ⅳ)掺杂量分别为2%和0.04%时,纳米TiO2光催化剂具有较高的催化活性,自然光照射下光催化氧化处理卷烟厂蒸叶车间废水,效果较好,废水COD去除率达到86.11%.     

AgNbO3/石墨烯复合材料的合成及其可见光催化甲基橙降解活性

采用固相法合成AgNbO₃/石墨烯复合纳米材料,利用透射电子显微镜(TEM)及紫外-可见漫反射光谱(UV-Vis)对样品的形貌及光学性质进行了表征。研究发现,AgNbO₃与石墨烯复合后,带隙能明显降低,吸收光波长范围增大。以甲基橙溶液的降解为光催化模型反应评价了AgNbO₃/石墨烯复合纳米材料的可见光催化性能。结果表明:与纯AgNbO₃相比,AgNbO₃/石墨烯复合纳米材料对甲基橙的可见光催化性能明显增强。实验条件下,经300 ℃煅烧的AgNbO₃/石墨烯(2:1)复合纳米材料表现出最优的催化性能,它对甲基橙的可见光催化脱色速率系数约为纯AgNbO₃的10倍。光催化降解机理研究表明,促使甲基橙降解脱色的主要活性物种为·O₂^- 和 h⁺。     

Ti(SO_4)_2水解-水热法制备锐钛型纳米TiO_2及其光催化性能

以Ti(SO4)2水溶液为原料,在水热条件下直接水解合成了锐钛型纳米TiO2颗粒。利用透射电镜(TEM)、X射线衍射(XRD)、BET低温吸附和紫外-可见光谱(UV-Vis)等方法对产物进行了表征,并研究了样品光催化降解甲基橙(MO)的性能。结果表明所制得纳米TiO2颗粒为锐钛矿型,晶型良好,平均粒径为24 nm,BET比表面积约为56.20 m2.g-1。光催化活性与商品纳米TiO2(P25)相近,具有良好的工业应用前景。     

铁氮共掺杂纳米TiO_2复合膜的制备、光谱分析及光催化活性研究

用溶胶-凝胶法制备铁、氮共掺杂纳米TiO2凝胶,浸渍-提拉法将其镀膜于载玻片表面,经干燥、煅烧,制得Fe-TiO2-xNr复合膜;用XRD,SEM,XPS及UV-Vis对镀膜样品进行了表征.XRD分析表明,Fe-TiO2-xNr膜为锐钛矿结构,少数氮原子替代了TiO2晶格中的氧;SEM照片说明,构成膜的粒子分散均匀,形貌一致,粒径约19 nm:UV-Vis漫反射光谱显示,Fe3+掺杂可使复合膜对可见光的响应红移至740nm处;XPS图谱证明,铁、氮的掺入降低了Ti(2p3/2)电子结合能,从而拓宽了TiO2在可见光区的吸收范围.以光催化降解苏丹红I为模型反应,比较了不同掺杂样品的光催化活性,结果表明,当掺杂的Fe3+相对于Ti4-1的原子比达到0.4%时,复合膜表现出最佳催化性能,4 h后对苏丹红I的降解率达到97%.方法制备的氮和适量铁共掺杂Fe-TiO2-xNr复合膜能协同提高TiO2对可见光的响应能力及光催化活性,在污水处理领域具有潜在的应用价值.     

Photocatalytic Activity of N-doped TiO2 Photocatalysts Prepared from the Molecular Precursor (NH4)2TiO(C2O4)2

用不同温度控制分解草酸氧钛铵制备N掺杂TiO₂光催化剂．利用XRD、IR、热分析、N₂吸-脱附等温线、XPS、紫外可见漫反射光谱和SEM表征了N-TiO₂光催化剂的结构．400～600 oC焙烧的N-TiO₂光催化剂为纯锐钛矿相,而700 oC焙烧的N-TiO₂光催化剂为锐钛矿和金红石混合相．N掺杂在TiO₂的间隙位使锐钛矿相TiO₂带隙变窄．在光降解甲基橙的反应中,600和400 oC焙烧的N-TiO₂催化剂分别在紫外光和全波长光照射下有最好活性;700 oC焙烧的N-TiO₂催化剂无论在紫外光和全波长光下都表现出最好的比活性,即最高的光量子效率,这可以归因于700 oC焙烧的N-TiO₂光催化剂良好的结晶程度和锐钛矿-金红石异相结的存在．     

Determination of photocatalytic activity in amorphous and crystalline titanium oxide films prepared using plasma-enhanced chemical vapor deposition

Hydro-oxygenated amorphous titanium oxide (a-TiO_x:OH) films were prepared by plasma-enhanced chemical vapor deposition (PECVD) using precursors of titanium tetraisopropoxide (TTIP) and oxygen. The influences of chemical states and crystal quality on the photocatalytic activity were systematically investigated in the as-deposited and post-annealed films. The degree of the photocatalytic activity was deeply correlated with the porosity related to the hydroxyl (OH) groups in the as-deposited amorphous film. The crystallized anatase structures was observed from the 200 °C-deposited a-TiO_x:OH film after a post-annealing treatment at 400 °C. The photocatalytic activity related to the film with anatase structure was markedly superior to that of an amorphous film with porous structures. The larger the crystal size of the anatase structure, the higher the photocatalytic activity obtained. At elevated annealed temperatures, the inferior anatase structure due to the crystalline transformation led to a low photocatalytic activity. It was concluded that the photocatalytic activity of an amorphous TiO_x film prepared using PECVD was determined by the porosity originating from the functional OH groups in the film, whereas the crystalline quality of anatase phase in the annealed poly-TiO_x film was crucial to the photocatalytic activity.     

Low-temperature hydrothermal synthesis of highly photoactive mesoporous spherical TiO2 nanocrystalline

TiO₂ microspheres with mesoporous textural microstructures and high photocatalytic activity were prepared by hydrothermal treatment of mixed solution of titanium sulfate and urea with designed time. The prepared samples were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and N₂ adsorption-desorption measurements. The photocatalytic activity was evaluated via the photocatalytic oxidation of acetone in air at room temperature. The results show that the hydrothermal time significantly influences on the morphology, microstructure and photocatalytic activity of the as-prepared samples. With increasing hydrothermal time, specific surface areas and pore volumes decrease, contrarily, the crystallite size and relative anatase crystallinity increase. The photocatalytic efficiency of the as-prepared samples is obviously higher than that of commercial Degussa P25 (P25) powders. Especially, the as-prepared TiO₂ powders by hydrothermal treatment for 7 h shows the highest photocatalytic activity, which exceeds that of P25 by a factor of more than 2 times.     

Synthesis and characterization of nanocrystalline titanium nitride powder from rutile and anatase as precursors

In this research nanosized titanium nitride powder was synthesized through reaction of titanium oxide with ammonia gas. The reaction was carried out at a very slow heating rate. Two different TiO₂ starting powders contained rutile and anatase phase and differed in initial particle size and surface area. The crystallite size of TiN powders synthesized at 1000 °C was obtained about 40 nm for anatase sample. Surface area and particle size were found to be 19 m²/g, 70 nm for rutile sample and 31 m²/g, 39 nm for anatase sample, respectively. The rutile sample showed an increasing trend in surface area during conversion to the nitride, whilst the anatase sample followed an adverse trend. TiN powder synthesized from anatase had the highest surface area and smallest particle size due to the specification of initial precursor.     

Effect of Particle Size and Phase Composition of Titanium Dioxide Nanoparticles on the Photocatalytic Properties

Titanium dioxide (TiO₂) nanoparticles were prepared by the oxidation of titanium tetrachloride (TiCl₄) in a diffusion flame reactor. The average diameter of particles was 15–30 nm and mass fraction of anatase ranged from 40% to 80%. Effects of particle size and phase composition of those TiO₂ nanoparticles on photocatalytic properties such as decomposition of methylene blue, bacteria and ammonia gas were investigated. The degree of decomposition of methylene blue by the TiO₂ nanoparticles under the illumination of the black light was directly proportional to the anatase mass fraction, but inversely to the particle size. The decomposition of bacteria and ammonia gas by the TiO₂ nanoparticles under the illumination of the fluorescent light showed the same trend as in the case of the methylene blue.     

Synthesis and characterization of nitrogen-doped TiO2 coatings on reduced graphene oxide for enhancing the visible light photocatalytic activity

Nitrogen-doped TiO₂ coatings on reduced graphene oxide were prepared via a sonochemical synthesis and hydrothermal process. The nanocomposites showed improved photocatalytic activity due to their large specific surface areas (185–447 m²/g), the presence of TiO₂ in the anatase phase, and a quenched photoluminescence peak. In particular, GN3-TiO₂ (nitrogen-doped TiO₂ coatings on rGO with 3 ml of titanium (IV) isopropoxide) exhibited the best photocatalytic efficiency and degradation rate among the materials prepared. With nitrogen-doped on the reduced graphene oxide surface, the photocatalytic activity is enhanced approximately 17.8 times compared to that of the pristine TiO₂. The dramatic enhancement of activity is attributed to the nitrogen contents and rGO effectively promoting charge-separation efficiency and providing abundant catalytically active sites to enhance the reactivity. The composites also showed improved pollutant adsorption capacity, electron–hole pair lifetime, light absorption capability, and absorbance of visible light.     

Low-temperature preparation of F-doped TiO2 film and its photocatalytic activity under solar light

A novel and simple method for preparing F-doped anatase TiO₂ (defined as FTO) film with high photocatalytic activity was developed using titanium-n-butoxide and NH₄F as TiO₂ and fluorine precursors under mild condition, i.e. low temperature (lower than 373 K) and ambient pressure. The prepared samples were characterized by XRD, SEM, X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectrum (DRS), photoluminescence spectrum (PL) and TG-DSC analysis. The photocatalytic activity was evaluated by decomposing X-3B under artificial solar light. The results showed that the crystallinity of TiO₂ was improved by F-doping. F⁻ ions can prevent the grain growth, and the transformation of anatase to rutile phase was also inhibited. The doped fluorine atoms existed in two chemical forms, and the ones incorporated into TiO₂ lattice might take a positive role in photocatalysis. Compared with surface fluorination samples, FTO film exhibited better photocatalytic activity. The high photocatalytic activity of FTO may due to extrinsic absorption through the creation of oxygen vacancies rather than the excitation of the intrinsic absorption band of bulk TiO₂. Furthermore, the FTO can be recycled with little photocatalytic activity depression. Without any further treatment besides rinsing, after 6 recycle utilization, the photocatalytic activity of FTO film was still higher than 79%.     

Photocatalytic thin films containing TiO2:N nanopowders obtained by the layer-by-layer self-assembling method

In this work, TiO₂-N powders were synthesized by high-energy ball milling, using commercial titanium dioxide (TiO₂) in the anatase phase and urea to introduce nitrogen into TiO₂ in order to enhance their photocatalytic properties in the visible spectral region. Several samples were prepared by milling a mixture of TiO₂-urea during 2, 4, 8, 12 and 24 h and characterized by spectroscopic and analytical techniques. X-ray diffraction (XRD) results showed the coexistence of anatase and high-pressure srilankite TiO₂ crystalline phases in the samples. Scanning electron microscopy (SEM) revealed that the grain size of the powder samples decreases to 200 nm at 24 h milling time. UV-Vis diffuse reflectance spectroscopic data showed a clear red-shift in the onset of light absorption from 387 to 469 nm as consequence of nitrogen doping in the samples. The photocatalytic activity of the TiO₂-N samples was evaluated by methylene blue degradation under visible light irradiation. It was found that TiO₂-N samples had higher photocatalytic activity than undoped TiO₂ samples, which could be assigned to the effect of introducing N atoms and XPS results confirm it. Using polyethylenimine (PEI), transparent thin films of TiO₂-N nanoparticles were prepared by layer-by-layer self assembly method. UV-visible spectrophotometry was employed in a quantitative manner to monitor the adsorbed mass of TiO₂ and PEI after each dip cycle. The adsorption of both TiO₂ and PEI showed a saturation dip time of 15 min.     

Preparation, characterization and photocatalytic activity of polycrystalline Bi2O3/SrTiO3 composite powders

Bi₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidation of methanol. These powders were characterized by UV-Visible diffuse reflectance spectra, SEM and X-ray diffraction (XRD). The results revealed that all the Bi₂O₃/SrTiO₃ composite powders exhibited higher photocatalytic activity than pure SrTiO₃, Bi₂O₃ and TiO₂ (P25) under visible light irradiation (λ>440 nm). The effects of the Bi₂O₃ contents on the photocatalytic activities of the composite powders were examined, the photocatalytic activities increased with the content of Bi₂O₃ increasing to a maximum of 83% and then decreased under visible light irradiation. The effects of the calcination temperatures on the photocatalytic activities of the composite powders were also investigated.     

掺Fe3+A-TiO2粉末的制备及其可见光催化降解碱性品红

以硫酸钛为原料用水热法制备了掺Fe3+TiO2粉末,用SEM测定了样品的形貌和晶型,研究了以自制的掺Fe3+ A-TiO2对碱性品红溶液的光催化降解作用.结果表明:所制备的TiO2为锐铁矿型TiO2(A-TiO2).可见光照射下,用自制的掺Fe3+A-TiO2降解碱性品红溶液的最佳条件是:2mg·L-1的碱性品红溶液中...     

二氧化钛薄膜的结构和光催化活性关系

用化学气相沉积法合成了具有不同晶体结构的二氧化钛薄膜，研究了二氧化钛薄膜的结构和光催化活性的关系．用XRD、AFM研究了薄膜的晶体组成和形貌，用亚硝酸根研究了薄膜的光催化活性．结果表明在制备温度低于573 K或高于773 K时，薄膜的结构分别为锐钛矿型或金红石型．而在上述温度之间生成的薄膜具有混合的晶型结构，特别是在623 K附近，制备的薄膜具有最高的光催化活性．进一步研究表明，当金红石与锐钛矿微晶体的比例在0.5?0.7时，催化剂薄膜具有高活性．