高温环境下柴油喷雾的燃烧特性

在高增压柴油机及陶瓷隔热柴油机的研制中，往往因柴油机燃烧室内压缩终了的温度参数较高（一般＞９００Ｋ），燃烧过程恶化，而导致达不到预期的功率、燃油经济性与排放指标。本文概括了我们在定容燃烧装置中模拟高强化柴油机燃烧室内的高温高压条件下，对柴油喷雾燃烧过程的研究结果。利用计算机对高速摄影图象处理并结合热力学分析计算，定量地考察了温度条件对着火，火焰发展和空气卷吸过程的影响，根据实验结果总结了柴油喷雾在高温条件下燃烧过程恶化的重要原因。     

生物柴油-生物油乳化油的燃烧排放特性

在一台未作改动的直喷式柴油机上研究了生物油质量分数分别为10%和20%的生物柴油生物油乳化油的燃烧与排放特性。结果表明:与生物柴油相比,燃用乳化油时燃烧始点推迟,预混燃烧放热峰值升高,扩散燃烧放热峰值、最高燃烧压力和燃烧温度降低,燃烧持续期缩短,且随着生物油含量增加以上趋势更明显。燃用含10%生物油的乳化油时燃油经济性较生物柴油略低,与0号柴油相当,而燃用含20%生物油的乳化油时燃油经济性则低于生物柴油和0号柴油。乳化油的NO_x排放明显低于生物柴油,而碳烟排放高于生物柴油,但低于0号柴油。     

DMM燃料柴油机可控预混合燃烧的研究

本文介绍了在压燃式发动机上进行的预混合燃烧研究。在柴油机的进气道入口处安装了一个电控燃料喷射系统,喷入具有低十六烷值、低沸点的甲缩醛(DMM)燃料,在压缩冲程中形成均匀的混合气,并在上止点附近喷入少量柴油来点燃混合气。本文研究了预混合燃料比、发动机负荷、进气中CO2浓度和喷孔直径对发动机燃烧和排放的影响。试验结果表明,进气道喷射DMM的预混合燃烧能同时大幅降低NOx和碳烟排放,为降低柴油机有害排放提供了一种新途径。     

生物柴油发动机非常规排放的FTIR检测

采用傅里叶变换红外光谱FTIR,研究了汽车发动机燃用生物柴油的非常规排放物。所用燃料分别为纯柴油、纯生物柴油、生物柴油掺混比为20%的B20混合燃料。结果表明,该机燃用纯柴油和B20燃油的甲醛排放差别不大,纯生物柴油的甲醛排放则明显高于柴油。燃用B20燃油的乙醛排放略低于纯柴油;纯生物柴油的乙醛排放在中低负荷低于纯柴油,在高负荷时高于柴油及B20燃油。燃用B20燃油和纯生物柴油的丙酮排放要高于柴油,但排放量均较低。随着生物柴油掺混比例的增加,发动机甲苯和二氧化硫均呈逐渐下降趋势,纯生物柴油的二氧化硫排放大幅降低。燃用生物柴油后,发动机的二氧化碳排放有所降低,表明了生物柴油有利于温室气体的控制。     

燃用天然气合成油增压柴油机特性研究

在一台增压中冷柴油机上分别燃用常规柴油与代用燃料天然气合成油(GTL),供油提前角分别设为上止点前9°和12°CA,对比研究了燃用这两种燃料的柴油机动力性、经济性、燃烧和排放特性.与柴油相比,燃用GTL的柴油机有效功率和转矩不变,有效燃油油耗率降低,有效热效率相当;GTL的最高燃烧压力和放热率峰值均略低,GTL的着火时刻、缸压和放热率峰值出现时刻均略晚,燃烧持续期略长;与柴油相比,在试验工况下GTL平均降低了16.6%HC、14.5%CO、15.7%碳烟和15.1%NOx排放.试验结果显示GTL是一种有潜力的低排放代用燃料.     

用速度浓度同步测量系统研究瞬态气体撞壁射流混合过程

用速度浓度同步测量系统研究瞬态气体撞壁射流混合过程谢辉，苏万华，史绍熙，林荣文（天津大学内燃机燃烧学国家重点实验室天津３０００７２）关键词撞壁射流，射流混合，速度浓度同步测量１引言对于中小型直喷式柴油机，燃油喷雾与壁面撞击不可避免，研究喷雾和壁面的相...     

喷雾夹角对柴油机性能影响的数值模拟

为研究喷雾夹角对柴油机性能的影响,应用STAR-CD程序对不同喷雾夹角的燃烧过程进行三维数值模拟.计算结果表明喷雾夹角决定了油束在燃烧室的空间分布和燃油与壁面的碰撞参数,进而影响到燃油的雾化与燃烧.当碰撞距离增加,燃油雾化时间增加.当撞壁入射角度减小,燃油壁面涂布能力增强,促进燃油蒸发雾化.当油束将燃烧室有效容积等分时,油气混合均匀,具有良好的燃烧效果.     

发动机燃用生物柴油的核态颗粒排放

以一台电控高压共轨柴油机为样机,使用排气颗粒数量及粒径分析仪EEPS,研究了发动机燃用生物柴油的核态颗粒排放特性。所用燃油为纯柴油、生物柴油掺混配比分别为5%、10%和20%的B5、B10和B20燃料。结果表明:发动机排气颗粒数量随粒径变化呈现明显的单峰或双峰对数分布形态,核态颗粒的峰值粒径在6 nm至10 nm之间。生物柴油配比上升,增加了该机核态颗粒的峰值数量浓度,颗粒总数量浓度大都呈持续上升趋势,其中核态颗粒数量增加占有主导因素;在低负荷燃用低配比生物柴油燃料时,B10燃油的颗粒总数量浓度最低。     

煤基复合燃料柴油机不同海拔燃烧与排放特性

基于柴油机高海拔燃烧与排放特性模拟试验台,开展了煤基复合燃料(33%煤基含氧燃料,67%-35#柴油)柴油机不同海拔燃烧与排放特性研究。结果表明,随着海拔升高,煤基复合燃料柴油机最高燃烧压力降低,放热率峰值下降,滞燃期延长,PM2.5排放增加,海拔2500 m标定工况PM2.5排放比平原增加28.9%。与燃用柴油相比,相同海拔下,煤基复合燃料柴油机滞燃期延长,燃烧持续期缩短,PM2.5排放减少,且海拔越高PM2.5排放降低幅度越大。煤基复合燃料柴油机高海拔燃烧过程数值模拟结果表明,海拔5500 m煤基复合燃料soot排放明显降低。     

DMM及纳米颗粒添加剂对农用柴油机燃烧与排放性能的影响

本文通过在柴油中添加小比例二甲氧基甲烷(DMM)以及纳米氧化铝(Al2O3)颗粒研究一台小型农用柴油机的燃烧与排放特性。研究表明,随着柴油中DMM添加比例的增大,发动机燃烧特性参数如缸内压力、燃烧放热率及制动热效率得到明显地提升,着火延迟期以及CA50逐渐减小;排放方面HC和NOx增加,而CO和碳烟得到有效地抑制。燃油中同时添加DMM和纳米Al2O3颗粒后,发动机燃烧及排放方面得到了不同程度地优化。因此,将DMM与纳米颗粒的有机结合可为代用燃料在农用发动机中的推广应用提供新的思路。     

油束撞击形成混合气及其燃烧过程的机理研究

本文介绍了用多次喷雾叠加摄影与激光粒子分析技术对燃油喷雾撞击前后的粒径、贯穿度以及喷雾锥角等因素变化所进行的观察和测量以及介绍了利用双像高速摄影技术对燃油束撞击雾化形成的混合气以及燃烧过程特点的研究。结果表明,燃油经撞击后可显著地增大油束扩散角、不同程度地影响了燃油束的贯穿度,但对燃油束撞击前后滴径变化的影响不大。混合气形成及其燃烧过程的高速摄影研究结果表明,燃油束撞击雾化对加快燃油与空气的混合并促进其火焰扩展起到重要作用。另外撞击反弹方向和喷油压力等也是影响混合气形成和燃烧的重要因素。     

Flow-field measurements of liquid and gaseous phases in the ultra-dense region of diesel sprays

The velocities of both the liquid and the gaseous phases in a diesel spray are determined for the first time simultaneously via laser flow tagging (LFT). The experimental setup and uncertainties introduced by seeding particles in the gas phase are greatly reduced by using phosphorescent tracer molecules, i.e. acetone and biacetyl, for the gaseous phase. In addition, simultaneous droplet velocimetry is achieved by doping the liquid fuel with a lanthanide–chelate complex.The relative velocity of gas and liquid phases can be determined from the data on the spray axis close to the nozzle for the first time. This is an important quantity for modeling droplet break-up and evaporation in ultra-dense sprays.PACS 42.62.-b; 47.61.Jd     

Modelling biodiesel–diesel spray combustion using multicomponent vaporization coupled with detailed fuel chemistry and soot models

A multicomponent vaporization model is integrated with detailed fuel chemistry and soot models for simulating biodiesel–diesel spray combustion. Biodiesel, a fuel mixture comprised of fatty-acid methyl esters, is an attractive alternative to diesel fuel for use in compression-ignition engines. Accurately modelling of the spray, vaporization, and combustion of the fuel mixture is critical to predicting engine performance using biodiesel. In this study, a discrete-component vaporization model was developed to simulate the vaporization of biodiesel drops. The model can predict differences in the vaporization rates of different fuel components. The model was validated by use of experimental data of the measured biodiesel drop size history and spray penetration data obtained from a constant-volume chamber. Gas phase chemical reactions were simulated using a detailed reaction mechanism that also includes PAH reactions leading to the production of soot precursors. A phenomenological multi-step soot model was utilized to predict soot emissions from biodiesel–diesel combustion. The soot model considered various steps of soot formation and destruction, such as soot inception, surface growth, coagulation, and PAH condensation, as well as oxidation by oxygen and hydroxyl-containing molecules. The overall numerical model was validated with experimental data on flame structure and soot distributions obtained from a constant-volume chamber. The model was also applied to predict combustion, soot and NOx emissions from a diesel engine using different biodiesel–diesel blends. The engine simulation results were further analysed to determine the soot emissions characteristics by use of biodiesel–diesel fuels.     

Flame structure and stabilization of lean-premixed sprays in a counterflow with low-volatility fuel

An experimental study was performed on the combustion of lean-premixed spays in a counterflow. n-Decane was used as a liquid fuel with low volatility. The flame structure and stabilization were discussed based on the flame-spread mechanism of a droplet array with a low-volatility fuel. The spray flame consisted of a blue region and a yellow luminous region. The flame spread among droplets and group-flame formation through the droplet interaction were observed on the premixed spray side, while envelope flames were also observed on the opposing airflow side. The blue-flame region consisted of premixed flames propagating in the mixture layer around each droplet, the envelope diffusion flames around each droplet, the lower parts of the group diffusion flame surrounding each droplet cluster, and the envelope flame around droplets passing through the group flame. The flame was stabilized within a specific range of the mean droplet diameter via a balance between the droplet velocity and the flame-spread rate of the premixed spray.     

柴油混合闪蒸喷雾的探索研究

基于同时降低柴油机中的NOx和微粒的想法，作者提出混合闪蒸喷雾的设想，井建立了混合闪蒸试验台，以证实这种设想在喷雾阶段是否能实现．试验证实了混合闪蒸雾化改善柴油雾化的机理．文中分析了水油比、水的温度、压力对雾束形状、油滴平均直径的影响，对混合闪蒸用于实际柴油机的潜力做了估计．     

超声速气流中液体横向射流雾化过程数值模拟

为了更加深入了解超燃冲压发动机燃烧室中的燃料雾化机理,对来流Mach数为1.94的超声速气流中液体横向射流的雾化过程进行了数值模拟研究.计算采用Euler-Lagrange方法,液滴二次破碎模型采用K-H/R-T模型.计算结果表明:考虑液滴二次破碎时,采用雾化锥模型获得的射流穿透深度以及液滴速度分布与实验结果符合得很好;初始液滴直径对射流穿透深度和液滴分布的影响很小;随着初始雾化锥角的增加,相同横截面上的射流穿透深度逐渐减小.当不考虑液滴二次破碎时,液滴穿透深度及分布与所选的初始液滴直径有很大关系.      

Absorption of external thermal radiation in asymmetrically illuminated droplets

A theoretical model of thermal radiation absorption in semi-transparent droplets at the surface and inside a fuel spray is presented. Asymmetry of droplet illumination is taken into account. Results of Mie calculations of thermal radiation absorption inside large spherical droplets illuminated from a hemisphere are presented. Simple approximations for the angular and radial dependencies of the absorbed radiation power are suggested. These approximations are generalisations of the approximations suggested earlier by the authors for the case of symmetric illumination of droplets. They predict the results close to those which follow from the Mie calculations. Results of approximate calculations for a typical diesel fuel droplet at the periphery of the spray are presented. As in the case of symmetrical droplet illumination, an increased absorption of thermal radiation in the central area of the droplet is predicted. Also, at the illuminated side of the droplet, the absorption of radiation in a thin layer near the surface of the droplet is predicted, as in the case of symmetrical droplet illumination. Absorption of radiation in the central area of the droplet is related to the contribution of radiation in the spectral ranges of semi-transparency. The maximum of radiation absorption near the droplet surface is linked to the contribution of radiation in the vicinity of the diesel fuel absorption peak .     

Physical and chemical characteristics of ultrasonically-prepared water-in-diesel fuel: Effects of ultrasonic horn position and water content

An ultrasonic technique was applied to preparation of two-phase water-in-oil (W/O) emulsified fuel of water/diesel oil/surfactant. In this study, an ultrasonic apparatus with a 28 kHz rod horn was used. The influence of the horn tip position during ultrasonic treatment, sonication time and water content (5 or 10 vol%) on the emulsion stability, viscosity, water droplet size and water surface area of emulsion fuels prepared by ultrasonication was investigated. The emulsion stability of ultrasonically-prepared fuel significantly depended on the horn tip position during ultrasonic irradiation. It was found that the change in the stability with the horn tip position was partly related to that in the ultrasonic power estimated by calorimetry. Emulsion stability, viscosity and sum of water droplets surface area increased and water droplet size decreased with an increase in sonication time, and they approached each limiting value in the longer time. The maximum values of the viscosity and water surface area increased with water content, while the limiting values of the emulsion stability and water droplet size were almost independent of water content. During ultrasonication of water/diesel oil mixture, the hydrogen and methane were identified and the cracking of hydrocarbon components in the diesel oil occurred. The combustion characteristics of ultrasonically-prepared emulsion fuel were studied and compared with those of diesel oil. The soot and NOx emissions during combustion of the emulsified fuel with higher water contents were significantly reduced compared with those during combustion of diesel oil.