High pressure studies of the erbium-hydrogen system

High-pressure X-ray diffraction investigations up to 25 GPa using diamond anvil cell techniques (DAC) have been carried out on erbium and a series of erbium hydrides. The equations of state have been evaluated for ErH_1.95, ErH_2.091 (in the β-phase) and for γ-ErH₃. For comparison, the compressibility of pure erbium metal has also been determined in the same pressure range. A rapid drop of lattice volume at a pressure of about 14.5 GPa has been observed for ErH_2.091 accompanied by a color change of reflected light. This phenomenon was not observed in ErH_1.95 where the molar volume varied smoothly up to the highest pressure. A pressure-induced transformation from hexagonal to cubic phase has been detected for erbium trihydride. For pure erbium metal, a transition from hexagonal to samarium structure has been revealed, confirming previously reported behavior.     

Electrostatic spray deposited zinc oxide films for gas sensor applications

In this work, thin films of zinc oxide (ZnO) for gas-sensor applications were deposited on platinum coated alumina substrate, using electrostatic spray deposition (ESD) technique. As precursor solution zinc acetate in ethanol was used. Scanning electron microscopy (SEM) evaluation showed a porous and homogeneous film morphology and the energy dispersive X-ray analysis (EDX) confirmed the composition of the films with no presence of other impurities. The microstructure studied with X-ray diffraction (XRD) and Raman spectroscopy indicated that the ZnO oxide films are crystallized in a hexagonal wurtzite phase. The films showed good sensitivity to 1 ppm nitrogen dioxide (NO₂) at 300 °C while a much lower sensitivity to 12 ppm hydrogen sulphide (H₂S).     

Pressure-induced structural phase transition in rare-earth trihydrides. Part I. (GdH3, HoH3, LuH3)

High-pressure X-ray diffraction studies of gadolinum, holmium and lutetium trihydrides have been carried out in a diamond anvil cell up to 30 GPa at room temperature. A reversible structural phase transformation from the hexagonal to cubic phase has been observed for all the hydrides investigated. These results confirm our first discovery of the hexagonal to cubic phase transition in erbium trihydride published recently [T. Palasyuk, M. Tkacz, Solid State Commun. 130 (2004) 219. [1]]. The lattice parameters of the new cubic phases and the volume changes at transition points were determined for SmH₃, GdH₃, and HoH₃. The parameters of the equation of state for all the hexagonal and cubic phases of the investigated compounds have been determined.     

Cathodoluminescent and nonlinear optical properties of undoped and erbium doped nanostructured ZnO films deposited by spray pyrolysis

We have deposited zinc oxide (ZnO) and erbium doped zinc oxide (ZnO:Er) thin films on heated glass substrates using spray pyrolysis technique. The effect of erbium dopant on structural, morphological, luminescent and nonlinear optical properties was studied. The deposited films have been analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), ex situ compositional analysis (ESCA), profilometry, cathodoluminescence (CL) and third harmonic generation (THG) measurements. All films were polycrystalline, having a preferential growth orientation along the ZnO (0 0 2) plane, with a corresponding average crystallite size of less than 41 nm. Addition of erbium can effectively control the film surface morphology and its cathodoluminescent properties. The films containing low erbium concentration show a uniform surface covered with hexagonal shaped grains and a strong UV light emission intensity as well as TH response. In contrast, when the erbium doping ratio exceeds 3%, a porous surface with columnar textural growth becomes more pronounced, and a substantial reduction of the cathodoluminescent and TH response. A strong TH signal was obtained for the film with good crystalline quality at the concentration of 2%. Third order nonlinear optical susceptibility (χ^〈3〉) values of the studied materials were in the remarkable range of 10⁻¹² esu.     

Green photoluminescence from highly oriented ZnO thin film for photovoltaic application

We report here the fabrication of ZnO nanoparticles embedded on glass substrate by sol–gel and spin coating technique. Transmission electron microscope images revealed that the thin film is composed of ZnO nanoparticles. X-ray diffraction data confirms that the fabricated ZnO nanoparticles have hexagonal unit cell structure. The ZnO nanocrystals of the thin film are oriented along the c-axis of the hexagonal unit cell. UV–vis absorption spectroscopy shows that the absorption occurring at 373 nm in the ZnO thin film. The band gap was calculated from the absorption data and found to be 3.76 eV. This band gap enhancement occurs due to size effect in the nanoscale regime. Room temperature photoluminescence spectrum shows strong green emission at 530 nm owing to the singly ionized oxygen vacancy. This green emission was further investigated by annealing the thin film at different temperature. This singular green emission will be very useful in optoelectronic and nanophotonic devices.     

Surface properties of cubic boron nitride thin films

Studying the surface properties of cubic boron nitride (c-BN) thin films is very important to making it clear that its formation mechanism and application. In this paper, c-BN thin films were deposited on Si substrates by radio frequency sputter. The influence of working gas pressure on the formation of cBN thin film was studied. The surface of c-BN films was analyzed by X-ray photoelectron spectroscopy (XPS), and the results showed that the surface of c-BN thin films contained C and O elements besides B and N. Value of N/B of c-BN thin films that contained cubic phase of boron nitride was very close to 1. The calculation based on XPS showed that the thickness of hexagonal boron nitride (h-BN) on the surface of c-BN films is approximately 0.8 nm.     

Surface chemical states of barium zirconate titanate thin films prepared by chemical solution deposition

Ba(Zr_0.05Ti_0.95)O₃ (BZT) thin films grown on Pt/Ti/SiO₂/Si(1 0 0) substrates were prepared by chemical solution deposition. The structural and surface morphology of BZT thin films has been studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). The results showed that the random oriented BZT thin film grown on Pt/Ti/SiO₂/Si(1 0 0) substrate with a perovskite phase. The SEM surface image showed that the BZT thin film was crack-free. And the average grain size and thickness of the BZT film are 35 and 400 nm, respectively. Furthermore, the chemical states and chemical composition of the films were determined by X-ray photoelectron spectroscopy (XPS) near the surface. The XPS results show that Ba, Ti, and Zr exist mainly in the forms of BZT perovskite structure.     

Influence of air annealing on the structural, morphological, optical and electrical properties of chemically deposited ZnSe thin films

Zinc selenide nanocrystalline thin films are grown onto amorphous glass substrate from an aqueous alkaline medium, using chemical bath deposition (CBD) method. The ZnSe thin films are annealed in air for 4 h at various temperatures and characterized by structural, morphological, optical and electrical properties. The as-deposited ZnSe film grew with nanocrystalline cubic phase alongwith some amorphous phase present in it. After annealing metastable nanocrystalline cubic phase was transformed into stable polycrystalline hexagonal phase with partial conversion of ZnSe into ZnO. The optical band gap, E_g, of as-deposited film is 2.85 eV and electrical resistivity of the order of 10⁶-10⁷ Ω cm. Depending upon annealing temperature, decrease up to 0.15 eV and 10² Ω cm were observed in the optical band gap, E_g, and electrical resistivity, respectively.     

Co growth on Si(0 0 1) and Si(1 1 1) surfaces: Interfacial interaction and growth dynamics

In situ X-ray photoelectron spectroscopy (XPS) and ex situ atomic force microscopy (AFM) were used to study the growth of thin cobalt films at room temperature (RT) on both clean and H-terminated Si(0 0 1) and Si(1 1 1) surfaces. The growth proceeds by first forming an initial CoSi₂-like phase at the growth front of the Si substrate. With increasing Co coverage the interfacial layer composition becomes richer in Co and eventually a metallic Co film is formed on top. Hydrogen termination of the Si surface did not suppress the reaction of Co and Si. A pseudo-layer-by-layer growth mode is proposed to describe the growth of Co on H-terminated Si surfaces, while closed-packed small island growth occurs on clean Si surfaces. The difference in growth mode can be attributed to the increase in the surface mobility of Co adatoms in the presence of hydrogen.     

Effects of annealing in nitrogen atmosphere and HCl-etching on the photoluminescence spectra of spray-deposited CdS:In thin films

The aim of this work is to find the effect of processing on the photoluminescence (PL) of spray-deposited CdS:In thin films. So the PL spectra of the as-deposited, annealed and HCl-etched CdS:In thin films prepared by the spray pyrolysis (SP) technique were recorded at T = 23 K. The yellow and red bands were observed in the spectrum of the as-deposited film beside bands with weaker intensity in the infrared region. The PL signal was weakened by annealing in nitrogen atmosphere at T = 400 °C and HCl-etching. A deconvolution peak fit was established to find the effects of these treatments on the different bands. The spectrum of the as-deposited film was deconvoluted to 12 peaks, which were reduced to 6 peaks after both treatments. It was found that both treatments have approximately the same effects on the PL spectra; that is they removed most of the peaks and shoulders in the red and infrared regions and attenuated most of the peaks in the yellow region. Some peaks were blue-shifted after annealing which was explained by the growth of nanocrystallites due to the thermal stress that results from the different expansion coefficients of the film and the substrate. These changes were accompanied by a phase change from the mixed (cubic and hexagonal) phase to the hexagonal phase as shown in the X-ray diffractograms.     

Synthesis, characterization of chemically deposited indium selenide thin films at room temperature

Polycrystalline In₂Se₃ semiconducting thin films were prepared by using relatively simple chemical bath deposition method at room temperature by the reaction between indium chloride, tartaric acid, hydrazine hydrate and sodium selenosulphate in an aqueous alkaline medium. Various preparative conditions of thin film deposition are outlined. The as grown films were found to be transparent, uniform, well adherent and red in color. The films were characterized using X-ray diffraction (XRD), scanning electron microscopy, atomic absorption spectroscopy and energy dispersive atomic X-ray diffraction (EDAX). The XRD analysis of the film showed the presence of polycrystalline nature with hexagonal crystal structure. SEM study revels that the grains are homogenous, without cracks or pinholes and well covers the glass substrate. The optical absorption and electrical conductivity was measured. The direct optical band gap value for the films was found to be of the order of 2.35 eV at room temperature and have specific electrical conductivity of the order of 10⁻² (Ω cm)⁻¹ showing n-type conduction mechanism. The utility of the adapted technique is discussed from the view-point of applications considering the optoelectric and structural data.     

Preparation and characterization of Mg-doped ZnO thin films by sol-gel method

Undoped and Mg-doped ZnO thin films were deposited on Si(1 0 0) and quartz substrates by the sol-gel method. The thin films were annealed at 873 K for 60 min. Microstructure, surface topography and optical properties of the thin films have been measured by X-ray diffraction (XRD), atomic force microscope (AFM), UV-vis spectrophotometer, and fluorophotometer (FL), respectively. The XRD results show that the polycrystalline with hexagonal wurtzite structure are observed for the ZnO thin film with Mg:Zn = 0.0, 0.02, and 0.04, while a secondary phase of MgO is evolved for the thin film with Mg:Zn = 0.08. The ZnO:Mg-2% thin film exhibits high c-axis preferred orientation. AFM studies reveal that rms roughness of the thin films changes from 7.89 nm to 16.9 nm with increasing Mg concentrations. PL spectra show that the UV-violet emission band around 386-402 nm and the blue emission peak about 460 nm are observed. The optical band gap calculated from absorption spectra and the resistivity of the ZnO thin films increase with increasing Mg concentration. In addition, the effects of Mg concentrations on microstructure, surface topography, PL spectra and electrical properties are discussed.     

Phase transformation in BN films by nitrogen-protected annealing at atmospheric pressure

Two groups of RF-sputtered BN films (pure hexagonal phase and approximately 27.5% cubic content, respectively) were annealed at 600 to 1000 °C under nitrogen at atmospheric pressure after deposition. FTIR spectroscopy indicates a reversible transformation from hexagonal phase to cubic phase, and again hexagonal phase. The most effective temperature for h-BN converting to cubic zincblende (c-BN) is 900 °C. Further, the indirectly stepwise transformation from hexagonal (h-BN) to explosive BN (E-BN) and then to c-BN employing metastable E-BN as an intermedium was observed. In addition, we tentatively put forward that the existence of defective h-BN and the N defects plays a key role on h-BN to c-BN transformation.     

Growth and oxidation of a Ni3Al alloy on Ni(1 0 0)

The growth and oxidation of a thin film of Ni₃Al grown on Ni(1 0 0) were studied using Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and high resolution electron energy loss spectroscopy (EELS). At 300 K, a 12 Å thick layer of aluminium was deposited on a Ni(1 0 0) surface and subsequently annealed to 1150 K resulting in a thin film of Ni₃Al which grows with the (1 0 0) plane parallel to the (1 0 0) surface of the substrate. Oxidation at 300 K of Ni₃Al/Ni(1 0 0) until saturation leads to the growth of an aluminium oxide layer consisting of different alumina phases. By annealing up to 1000 K, a well ordered film of the Al₂O₃ film is formed which exhibits in the EEL spectra Fuchs-Kliewer phonons at 420, 640 and 880 cm⁻¹. The LEED pattern of the oxide shows a twelvefold ring structure. This LEED pattern is explained by two domains with hexagonal structure which are rotated by 90° with respect to each other. The lattice constant of the hexagonal structure amounts to ∼2.87 Å. The EELS data and the LEED pattern suggest that the γ^′-Al₂O₃ phase is formed which grows with the (1 1 1) plane parallel to the Ni(1 0 0) surface.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Effect of temperature on pulsed laser deposition of HgCdTe films

HgCdTe thin films have been deposited on Si(1 1 1) substrates at different substrate temperatures by pulsed laser deposition (PLD). An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as laser source. The influences of the substrate temperature on the crystalline quality, surface morphology and composition of HgCdTe thin films were characterized by X-ray diffraction (XRD), selected area electron diffraction (SAED), atomic force microscopy (AFM) and energy dispersive X-ray spectroscopy (EDS). The results show that in our experimental conditions, the HgCdTe thin films deposited at 200 °C have the best quality. When the substrate temperature is over 250 °C, the HgCdTe film becomes thermodynamically unstable and the quality of the film is degraded.     

Thickness influence on surface morphology and ozone sensing properties of nanostructured ZnO transparent thin films grown by PLD

Transparent zinc oxide (ZnO) thin films with a thickness from 10 to 200 nm were prepared by the PLD technique onto silicon and Corning glass substrates at 350 °C, using an Excimer Laser XeCl (308 nm). Surface investigations carried out by atomic force microscopy (AFM) and X-ray diffraction (XRD) revealed a strong influence of thickness on film surface topography. Film roughness (RMS), grain shape and dimensions correlate with film thickness. For the 200 nm thick film, the RMS shows a maximum (13.9 nm) due to the presence of hexagonal shaped nanorods on the surface. XRD measurements proved that the films grown by PLD are c-axis textured. It was demonstrated that the gas sensing characteristics of ZnO films are strongly influenced and may be enhanced significantly by the control of film deposition parameters and surface characteristics, i.e. thickness and RMS, grain shape and dimension.     

Nanoporous nickel oxide thin films and its improved electrochromic performance: Effect of thickness

Electrochromic properties of chemically bath deposited nanoporous NiO thin films were investigated as a function of film thickness using Ni sulphate precursor, aqueous ammonia and potassium persulphate as complexing and oxidizing agents respectively. The films were characterized for their structural, morphological, optical and electrochromic properties using X-ray diffraction, scanning electron microscopy, FT-IR spectroscopy, cyclic voltammetry, chronoamperometry and optical transmittance studies. X-ray diffraction patterns show that the films are polycrystalline, consisting of NiO cubic phase. Infrared spectroscopy results show the presence of free hydroxyl ion and water in NiO thin films. SEM micrographs revealed nanoporous nature composed of interconnected nanoporous network, forming well defined 3D nano envelopes. The optical band gap energy was found to be decreased from 3.22 to 2.80 eV with increasing film thickness. The electrochromic properties of all the films were investigated in aqueous (KOH) and non aqueous (LiClO₄-PC) electrolyte by means of cyclic voltammetry (CV), chronocoulometry (CC) and optical studies. The transmittance modulations or optical density differences during the coloring/bleaching process were found to be increased with the film thickness. This increment in optical differences led to an increase in coloration efficiency (CE) to about 95 cm²/C, which is two times more than that observed in KOH and response time of 2.9 s for bleaching (reduction) and 3.5 s for coloration (oxidation) observed for the film deposited at 60 min with excellent electrochemical stability up to 3000 c/b cycles in LiClO₄-PC electrolyte.     

A novel sputtering oxidation coupling (SOC) method to fabricate VO2 thin film

VO₂ thin film synthesized by a novel sputtering oxidation coupling (SOC) method has been successfully fabricated. The experimental results show that the optimum oxidation time is 285 s and the thin film exhibits a good metal-insulator transition (MIT) approximately at 340 K. The corresponding structures and surface compositions of the films have been characterized by X-ray diffractometer and X-ray photoelectron spectroscopy separately.     

STUDY OF MICROSTRUCTURE AND ELECTROLUMINESCENCE OF ZINC SULFIDE THIN FILM

The electroluminscent zinc sulfide thin film doped with erbium, fabri cated by thermal evaporation with two boats, are examined. The surface and internal electronic states of ZnS thin film are measured by means of X-ray diffracti on and X-ray photoemission spectroscopy. The information on the relations between electroluminescent characteristics and internal electronic states of the film is obtained. And the effects of the microstructure of thin film doped with rare earth erbium on electroluminescence are discussed as well.