The influence of different doping elements on microstructure, piezoelectric coefficient and resistivity of sputtered ZnO film

ZnO film is attractive for high frequency surface acoustic wave device application when it is coupled with diamond. In order to get good performance and reduce insertion loss of the device, it demands the ZnO film possessing high electrical resistivity and piezoelectric coefficient d₃₃. Doping ZnO film with some elements may be a desirable method. In this paper, the ZnO films undoped and doped with Cu, Ni, Co and Fe, respectively (doping concentration is 2.0 at.%) are prepared by magnetron sputtering. The effect of different dopants on the microstructure, piezoelectric coefficient d₃₃, and electrical resistivity of the film are investigated. The results indicate that Cu dopant can enhance the c-axis orientation and piezoelectric coefficient d₃₃, the Cu and Ni dopant can increase electrical resistivity of the ZnO film up to 10⁹ Ω cm. It is promising to fabricate the ZnO films doped with Cu for SAW device applications.     

Microstructures and optical properties of Cu-doped ZnO films prepared by radio frequency reactive magnetron sputtering

Pure and Cu-doped ZnO (ZnO:Cu) thin films were deposited on glass substrates using radio frequency (RF) reactive magnetron sputtering. The effect of substrate temperature on the crystallization behavior and optical properties of the ZnO:Cu films have been studied. The crystal structures, surface morphology and optical properties of the films were systematically investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and a fluorescence spectrophotometer, respectively. The results indicated that ZnO films showed a stronger preferred orientation toward the c-axis and a more uniform grain size after Cu-doping. As for ZnO:Cu films, the full width at half maxima (FWHM) of (0 0 2) diffraction peaks decreased first and then increased, reaching a minimum of about 0.42° at 350 °C and the compressive stress of ZnO:Cu decreased gradually with the increase of substrate temperature. The photoluminescence (PL) spectra measured at room temperature revealed two blue and two green emissions. Intense blue-green luminescence was obtained from the sample deposited at higher substrate temperature. Finally, we discussed the influence of annealing temperature on the structural and optical properties of ZnO:Cu films. The quality of ZnO:Cu film was markedly improved and the intensity of blue peak (∼485 nm) and green peak (∼527 nm) increased noticeably after annealing. The origin of these emissions was discussed.     

Sol-gel preparation and enhanced photocatalytic performance of Cu-doped ZnO nanoparticles

Cu-doped ZnO nanoparticles were prepared by a sol-gel method for the first time. XRD, XPS, UV-vis and FS techniques were used to characterize the Cu-doped ZnO samples. The photocatalytic activity was tested for methyl orange degradation under UV irradiation. The results show that the crystal sizes of ZnO and 0.5% Cu/ZnO nanoparticles with wurtzite phase are 32.0 and 28.5 nm, indicating that Cu-doping hinder the growth of crystal grains. The doped Cu element existed as Cu²⁺. The optimal Cu doping concentration in ZnO is 0.5%. The optimal calcination condition is at 350 °C for 3 h. The MO degradation rate of 0.5% Cu/ZnO reaches 88.0% when initial concentration of MO is 20 mg/L, exceeding that of undoped ZnO. The enhanced charge carrier separation and increased surface hydroxyl groups due to Cu-doping contributed to the enhanced photocatalytic activity of 0.5% Cu/ZnO.     

Effects of Cu doping on nickel oxide thin film prepared by sol–gel solution process

We prepared nickel oxide (NiO) thin films with p-type Cu dopants (5 at%) using a sol–gel solution process and investigated their structural, optical, and electrical characteristics by X-ray diffraction (XRD), atomic force microscopy (AFM), optical transmittance and current–voltage (I–V) characteristics. The crystallinity of the NiO films improved with the addition of Cu dopants, and the grain size increased from 38 nm (non-doped) to 50 nm (Cu-doped). The transmission of the Cu-doped NiO film decreased slightly in the visible wavelength region, and the absorption edge of the film red-shifted with the addition of the Cu dopant. Therefore, the width of the optical band gap of the Cu-doped NiO film decreased as compared to that of the non-doped NiO film. The resistivity of the Cu-doped NiO film was 23 Ω m, which was significantly less than that of the non-doped NiO film (320 Ω m). Thus, the case of Cu dopants on NiO films could be a plausible method for controlling the properties of the films.     

Effect of growth time on the structure, Raman shift and photoluminescence of Al and Sb codoped ZnO nanorod ordered array thin films

Al and Sb codoped ZnO nanorod ordered array thin films have been deposited on glass substrate with a ZnO seed layer by hydrothermal method at different growth time. The effect of growth time on structure, Raman shift, and photoluminescence (PL) was studied. The thin films at growth time of 5 h consist of nanorods growth vertically oriented with ZnO seed layer, and the nanorods with an average diameter of 27.8 nm and a length of 1.02 μm consist of single crystalline wurtzite ZnO crystal and grow along [0 0 1] direction. Raman scattering analysis demonstrates that the thin films at the growth time of 5 h have great Raman shift of 15 cm⁻¹ to lower wavenumber and have low asymmetrical factor Г_a/Г_b of 1.17. Room temperature photoluminescence reveals that there is more donor-related PL in films with growth time of 5 h.     

Defects enhanced ferromagnetism in Cu-doped ZnO thin films

We present here new evidences of point defects enhanced ferromagnetism in Cu-doped ZnO thin films by different characterization methods. Cu-doped ZnO thin films with Cu concentrations ranging from 0.05 to 5 at.% were prepared by an inductively coupled plasma enhanced physical vapor deposition system. Room-temperature ferromagnetism is observed in all the films. The saturation magnetization shows an increasing trend with the increase of Cu concentration except a slight decrease for the 1 at.% Cu-doping. Further study performed by Raman spectra, X-ray absorption spectra and extended X-ray absorption fine structure indicate the existence of Cu²⁺ ions and point defects in all the films. The local structural characterization and magnetic properties reveal that the sample with larger saturation magnetization has a higher concentration of point defects.     

Effects of the oxygen partial pressure and annealing atmospheres on the microstructures and optical properties of Cu-doped ZnO films

Cu-doped zinc oxide (ZnO:Cu) films were deposited on p-Si (1 0 0) substrates at 200 °C under various oxygen partial pressures by using radio frequency reactive magnetron sputtering. The properties of the films were characterized by the X-ray diffraction spectroscopy (XRD), energy dispersive spectrometer, X-ray photoelectron spectroscopy (XPS) and fluorescence spectrophotometer with the emphasis on the evolution of microstructures, element composition, valence state of Cu, optical properties. The results indicated that the properties of ZnO:Cu films were significantly affected by oxygen partial pressures. XRD measurements revealed that the sample prepared at the ratio of O₂:Ar of 15:10 sccm had the best crystal quality among all ZnO:Cu films. XPS analysis results suggested that the valence of Cu in the ZnO films was a mixed state of +1 and +2, and the integrated intensity ratio of Cu²⁺ to Cu⁺ increased with the increment of oxygen partial pressure. The photoluminescence measurements at room temperature revealed a violet, two blue and a green emission. We considered that the origin of green emission came from various oxygen defects when the ZnO:Cu films grew in oxygen poor and enriched environment. Furthermore, the influence of annealing atmosphere on the microstructures and optical properties of ZnO:Cu films were discussed.     

Structure, morphology and properties of Fe-doped ZnO films prepared by facing-target magnetron sputtering system

We have prepared a series of ZnO films with various concentrations of Fe dopant by using facing-target magnetron sputtering system and investigated their structure, morphology, optical properties and magnetic properties by means of the X-ray diffraction, Raman spectrometer, X-ray photoelectron spectroscopy, scanning electron microscope, UV-vis spectrophotometer, spectrofluorophotometer and vibrated sample magnetometer, respectively. The results showed Fe was in 2+ valence state in film. With increasing the concentration of Fe dopant the crystal quality deteriorated gradually and an increasing compressive stress occurred in ZnO films. All the grains grew with a columnar form along the [0 0 2] direction and the average size of grains decreased monotonically as the concentration of Fe dopant increased. The calculated results indicated that the band gap of films decreased with the increment of the concentration of Fe dopant, which resulted in the red-shift of violet emission peak. Moreover, the intensity of violet emission peak increased with the increment of Fe concentration because of the interface trap existing in depletion regions located at the ZnO grains boundaries. When the concentration of Fe dopant was smaller than 0.028, the films exhibited paramagnetic properties while the films displayed weak ferromagnetic properties when the concentration of Fe dopant increased to 0.041.     

Fabrication of Sb-doped p-type ZnO thin films by pulsed laser deposition

p-Type ZnO thin films have been realized via monodoping antimony (Sb) acceptor by using pulsed laser deposition. The obtained films with the best electrical properties show a hole concentration in the order of 10¹⁸ cm⁻³ and resistivity in the range of 2-4 Ω cm. X-ray diffraction measurements revealed that all the films possessed a good crystallinity with (0 0 2)-preferred orientation. Guided by X-ray photoemission spectroscopy analysis and a model for large-sized-mismatched group-V dopant in ZnO, an Sb_Zn-2V_Zn complex is believed to be the most possible acceptor in the Sb-doped p-type ZnO thin films.     

Optical and electrical characteristics of Al-doped ZnO thin films prepared by aqueous phase deposition

Transparent conducting Al-doped ZnO (AZO) thin films have been deposited by sol-gel route. Starting from an aqueous solution of zinc acetate by adding aluminum chloride as dopant, a c-axis oriented polycrystalline ZnO thin film 100 nm in thickness could be spin-coated on glass substrates via a two-step annealing process under reducing atmosphere. The effects of thermal annealing and dopant concentration on the structural, electrical and optical properties of AZO thin films were investigated. The post-treated AZO films exhibited a homogenous dense microstructure with grain sizes less than 10 nm as characterized by SEM photographs. The annealing atmosphere has prominent impact on the crystallinity of the films which will in turn influence the electrical conductivity. By varying the doping concentrations, the optical and electrical properties could be further adjusted. An optimal doping concentration of Al/Zn = 2.25 at.% was obtained with minimum resistivity of 9.90 × 10⁻³ Ω-cm whereas the carrier concentration and mobility was 1.25 × 10²⁰ cm⁻³ and 5.04 cm² V⁻¹ s⁻¹, respectively. In this case, the optical transmittance in the visible region is over 90%.     

Electrical and optical properties of ZnO films prepared by sputtering of ZnO targets containing AlN

ZnO films prepared from the ZnO target containing 2% AlN are transparent irrespective of radio frequency (RF) power. The obtained ZnO films have the carrier density of 3.8 × 10²⁰ cm⁻³ or less and the low mobility of 5.3-7.8 cm²/(V s). In the case of 5% AlN target, ZnO films prepared at 40, 60 and 80 W are transparent, whereas ZnO films prepared at 100 and 120 W are colored. As RF power increases from 40 to 120 W, the carrier density increases straightforwardly up to 5.5 × 10²⁰ cm⁻³ at 100 W and is oppositely reduced to 3.2 × 10²⁰ cm⁻³ at 120 W. In the case of 10% AlN target, ZnO films prepared at 60 W or more are colored, and have the carrier density of 4 × 10²⁰ cm⁻³ or less. The N-concentration in these colored films is estimated to be 1% or less. The Al-concentration in the ZnO films prepared from the 5 and 10% AlN targets is higher than 2%. The carrier density of the ZnO films containing Al and N atoms is nearly equal to that of ZnO films doped with Al atoms alone. There is no evidence in supporting the enhancement of the carrier density via the formation of N-Al_xZn_4−x clusters (4 ≥ x ≥ 2).     

Epitaxial growth of Sc-doped ZnO films on Si by sol-gel route

The epitaxial growth of doped ZnO films is of great technological importance. Present paper reports a detailed investigation of Sc-doped ZnO films grown on (1 0 0) silicon p-type substrates. The films were deposited by sol-gel technique using zinc acetate dihydrate as precursor, 2-methoxyethanol as solvent and monoethanolamine (MEA) as a stabilizer. Scandium was introduced as dopant in the solution by taking 0.5 wt%¹ of scandium nitrate hexahydrate. The effect of annealing on structural and photoluminescence properties of nano-textured Sc-doped films was investigated in the temperature range of 300-550 °C. Structural investigations were carried out using X-ray diffraction, scanning electron microscopy and atomic force microscopy. X-ray diffraction study revealed that highly c-axis oriented films with full-width half maximum of 0.21° are obtained at an annealing temperature of 400 °C. The SEM images of ZnO:Sc films have revealed that coalescence of ZnO grains occurs due to annealing. Ostwald ripening was found to be the dominant mass transport mechanism in the coalescence process. A surface roughness of 4.7 nm and packing density of 0.93 were observed for the films annealed at 400 °C. Room temperature photoluminescence (PL) measurements of ZnO:Sc films annealed at 400 °C showed ultraviolet peak at about (382 nm) with FWHM of 141 meV, which are comparable to those found in high-quality ZnO films. The films annealed below or above 400 °C exhibited green emission as well. The presence of green emission has been correlated with the structural changes due to annealing. Reflection high energy electron diffraction pattern confirmed the nearly epitaxial growth of the films.     

Observation of ferromagnetism at room temperature for Cr ions implanted ZnO thin films

Single crystalline ZnO films were grown on c-plane GaN/sapphire (0 0 0 1) substrates by molecular beam epitaxy. Cr⁺ ions were implanted into the ZnO films with three different doses, i.e., 1 × 10¹⁴, 5 × 10¹⁵, and 3 × 10¹⁶ cm⁻². The implantation energy was 150 keV. Thermal treatment was carried out at 800 °C for 30 s in a rapid thermal annealing oven in flowing nitrogen. X-ray diffraction (XRD), atomic force microscopy, Raman measurements, transmission electron microscopy and superconducting quantum interference device were used to characterize the ZnO films. The results showed that thermal annealing relaxed the stress in the Cr⁺ ions implanted samples and the implantation-induced damage was partly recovered by means of the proper annealing treatment. Transmission electron microscopy measurements indicated that the first five monolayers of ZnO rotated an angle off the [0 0 0 1]-axis of the GaN in the interfacial layer. The magnetic-field dependence of magnetization of annealed ZnO:Cr showed ferromagnetic behavior at room temperature.     

Effect of different dopant elements (Al,Mg and Ni) on microstructural,optical and electrochemical properties of ZnO thin films deposited by spray pyrolysis (SP)

In the present work we studied the influence of the dopant elements and concentration on the microstructural and electrochemical properties of ZnO thin films deposited by spray pyrolysis. Transparent conductive thin films of zinc oxide (ZnO) were prepared by the spray pyrolysis process using an aqueous solution of zinc acetate dehydrate [Zn(CH₃COO)₂·2H₂O] on soda glass substrate heated at 400 ± 5 °C. AlCl₃, MgCl₂ and NiCl₂ were used as dopant. The effect of doping percentage (2–4%) has been investigated. Afterwards the samples were thermally annealed in an ambient air during one hour at 500 °C. X-ray diffraction showed that films have a wurtzite structure with a preferential orientation along the (0 0 2) direction for doped ZnO. The lattice parameters a and c are estimated to be 3.24 and 5.20 ?, respectively. Transmission allowed to estimate the band gaps of ZnO layers. The electrochemical studies revealed that the corrosion resistance of the films depended on the concentration of dopants.     

Effects of rf power on surface-morphological, structural and electrical properties of aluminium-doped zinc oxide films by magnetron sputtering

Aluminium-doped zinc oxide (ZnO:Al) films were prepared by magnetron sputtering at different radio-frequency powers (P_rf) of 50, 100, 150 and 200 W. The properties of the films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), Raman microscopy, and spectrophotometry with the emphasis on the evolution of compositional, surface-morphological, optical, electrical and microstructural properties. XPS spectra showed that within the detection limit the films are chemically identical to near-stoichiometric ZnO. AFM revealed that root-mean-square roughness of the films has almost linear increase with increasing P_rf. Optical band gap E_gopt of the films increases from 3.31 to 3.51 eV when P_rf increases from 50 to 200 W. A widening E_gopt of the ZnO:Al films compared to the band gap (∼3.29 eV) of undoped ZnO films is attributed to a net result of the competition between the Burstein-Moss effect and many-body effects. An electron concentration in the films was calculated in the range of 3.73 × 10¹⁹ to 2.12 × 10²⁰ cm⁻³. Raman spectroscopy analysis indicated that well-identified peaks appear at around 439 cm⁻¹ for all samples, corresponding to the band characteristics of the wurtzite phase. Raman peaks in the range 573-579 cm⁻¹ are also observed, corresponding to the A₁ (LO) mode of ZnO.     

Effect of Co-doping content on hydrothermal derived ZnO array films

Cobalt doped ZnO films are synthesised using a hydrothermal process. The effect of Co²⁺ concentration on morphology, phase composition, crystallisation and spectroscopic characteristics of ZnO films is investigated. The results indicate that both the structure and morphology of the ZnO films evolve with the concentration of cobalt ions incorporated into the lattice. In the presence of a small amount of Co²⁺ ions, films are formed that comprise hexagonal ZnO nanorods, oriented with the c-axis perpendicular to the substrate. With increasing amount of Co²⁺, cracks in the ZnO nanorods can be observed and growth in the [0 0 1] direction is significantly inhibited. When the Co²⁺ concentration exceeds 0.010 M, ZnO rods with the typical hexagonal structure are no longer observed and instead, ZnO films comprising close-packed grains with an irregular polygonal structure are formed. The epitaxial growth of ZnO films is nearly completely inhibited when the concentration of Co²⁺ is increased above 0.050 M. This behaviour can be explained by the selective adsorption of the organic substances in the solution onto the (0 0 1) ZnO crystal face, thus inhibiting growth in the [0 0 1] direction and disrupting the crystallisation of ZnO films. Increasing the Co content deteriorates the crystallisation of ZnO rods and increases tensile stresses present in the ZnO films.     

Zn-interstitial-enhanced ferromagnetism in Cu-doped ZnO films

Copper-doped ZnO (ZnO:Cu) films exhibiting room-temperature (RT) ferromagnetism were prepared by filtered cathodic vacuum arc (FCVA) technique. The ZnO:Cu films deposited at RT showed the strongest magnetic moment of 0.40 μ_B/Cu as compared with the samples prepared at elevated temperatures. The observed strong ferromagnetism in the RT-deposited ZnO:Cu films could be partly associated with Zn-interstitial defects. The degradation of magnetic moment in the ZnO:Cu prepared at high temperatures and annealed at elevated temperatures might be attributed to the out-diffusion of Zn interstitials to the ZnO lattice.     

Magnetic and structural study of Cu-doped TiO2 thin films

Transparent pure and Cu-doped (2.5, 5 and 10 at.%) anatase TiO₂ thin films were grown by pulsed laser deposition technique on LaAlO₃ substrates. The samples were structurally characterized by X-ray absorption spectroscopy and X-ray diffraction. The magnetic properties were measured using a SQUID. All films have a FM-like behaviour. In the case of the Cu-doped samples, the magnetic cycles are almost independent of the Cu concentration. Cu atoms are forming CuO and/or substituting Ti in TiO₂. The thermal treatment in air promotes the CuO segregation. Since CuO is antiferromagnetic, the magnetic signals present in the films could be assigned to Cu substitutionally replacing cations in TiO₂.     

Effects of growth temperature on Li-N dual-doped p-type ZnO thin films prepared by pulsed laser deposition

Li-N dual-doped p-type ZnO (ZnO:(Li,N)) thin films have been prepared by pulsed laser deposition. The introduction of Li and N was confirmed by secondary ion mass spectrometry measurements. The structural, electrical, and optical properties as a function of growth temperature were investigated in detail. The lowest room-temperature resistivity of 3.99 Ω cm was achieved at the optimal temperature of 450 °C, with a Hall mobility of 0.17 cm²/V s and hole concentration of 9.12 × 10¹⁸ cm⁻³. The ZnO:(Li,N) films exhibited good crystal quality with a complete c-axis orientation, a high transmittance (about 90%) in the visible region, and a predominant UV emission at room temperature. The two-layer-structure p-ZnO:(Li,N)/n-ZnO homojunctions were fabricated on a sapphire substrate. The current-voltage characteristics exhibited the rectifying behavior of a typical p-n junction.     

Cathodoluminescent and nonlinear optical properties of undoped and erbium doped nanostructured ZnO films deposited by spray pyrolysis

We have deposited zinc oxide (ZnO) and erbium doped zinc oxide (ZnO:Er) thin films on heated glass substrates using spray pyrolysis technique. The effect of erbium dopant on structural, morphological, luminescent and nonlinear optical properties was studied. The deposited films have been analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), ex situ compositional analysis (ESCA), profilometry, cathodoluminescence (CL) and third harmonic generation (THG) measurements. All films were polycrystalline, having a preferential growth orientation along the ZnO (0 0 2) plane, with a corresponding average crystallite size of less than 41 nm. Addition of erbium can effectively control the film surface morphology and its cathodoluminescent properties. The films containing low erbium concentration show a uniform surface covered with hexagonal shaped grains and a strong UV light emission intensity as well as TH response. In contrast, when the erbium doping ratio exceeds 3%, a porous surface with columnar textural growth becomes more pronounced, and a substantial reduction of the cathodoluminescent and TH response. A strong TH signal was obtained for the film with good crystalline quality at the concentration of 2%. Third order nonlinear optical susceptibility (χ^〈3〉) values of the studied materials were in the remarkable range of 10⁻¹² esu.