Improving the electrical catalytic activity of Pt/TiO<Subscript>2</Subscript> nanocomposites by a combination of electrospinning and microwave irradiation

One of the greatest challenges in preparing TiO₂-based oxygen electrodes for PEM fuel cells is increasing the electrical catalytic activity of Pt nanoparticle/TiO₂ composites by improving the dispersion of Pt. This article describes a new way for improving the dispersion of Pt nanoparticles by depositing them on TiO₂ fibers and using microwave irradiation. The Pt nanoparticles used in this experiment is about 5 nm in diameter and the diameter of TiO₂ fibers could be controlled ranging from 30 to 60 nm and Pt nanoparticles still keep their size when the deposition amount is increased on the surface of TiO₂ fibers. The Pt nanoparticles were highly dispersed without agglomeration even at a weight percentage of composites as high as 40%. The position of Pt nanoparticles located in the fiber and the composition of Pt/TiO₂, which had great influence on the electric conductivity and electrical catalytic activity of the composite, could be easily controlled.     

Electrodeposition of platinum on tourmaline and application as an electrocatalyst for oxidation of methanol

A composite electrode of Pt nanoparticles coupled with tourmaline is prepared on glassy carbon (GC) disk electrode via electrodeposition. The nanocomposite of Pt/tourmaline is characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, X-ray powder diffraction, and transmission electron microscopy examinations linked with energy dispersive X-ray analysis. The electrocatalytic performance of the composite electrode (Pt/tourmaline/GC) is investigated in electrocatalysis oxidation of methanol at room temperature by cyclic voltammetry and chronoamperometry. It is indicated that Pt nanoparticles with size of ∼5 nm are uniformly assembled along the tourmaline particles and Pt exists in metallic and oxidated states confirmed by XPS. The results of electro-oxidation of methanol show that Pt/tourmaline catalyst is catalytically more active and stable than platinum-modified GC electrode, and the onset potential of Pt/tourmaline shifts 0.15 V to the negative side, and also the current density is significantly enhanced.     

Preferential Alignment of Hydroxyapatite Crystallites in Nanocomposites with Chemically Disintegrated Silk Fibroin

Hydroxyapatite (HAp) nanocrystals were prepared at room temperature by a coprecipitation method from Ca(OH)₂ and H₃PO₄, in the presence of chemically disintegrated silk fibroin (SF). Adsorbed amounts of cations on SF and crystallinity of HAp in the composite were increased by the chemical disintegration of SF higher order structure. Preferential alignment of c-axis of HAp crystallites along the longitudinal direction of ca. 150nm SF fibril was observed. These changes due to disintegration of SF were discussed in terms of the chemical interaction between HAp and SF. The resulted composite with preferential alignment of HAp nanocrystals is a good candidate as a starting material for bone substitutes.     

Synthesis,characterization, and electrochemical performance of nitrogen-modified Pt–Fe alloy nanoparticles supported on ordered mesoporous carbons

A method has been demonstrated to synthesize nitrogen-modified Pt–Fe alloyed nanoparticles (9.2–11.3 nm) supported on ordered mesoporous carbon (Pt _x Fe_100?x N/OMC), which is fabricated by a conventional wet chemical synthesis of Pt–Fe alloyed nanoparticles and followed by carbonization of the nanoparticles with tetraethylenepentamine as nitrogen chelating agent. Among these electrocatalysts, the Pt₃₀Fe₇₀N/OMC has highly catalytic activity for the oxygen reduction reaction (ORR) with significantly enhanced methanol tolerance as well. Combining the results from X-ray diffraction and X-ray absorption spectroscopy, it can be observed that Pt metal in the Pt₃₀Fe₇₀N/OMC is present in the outer shell of Pt–Fe alloys with face-centered cubic crystalline structure. By X-ray photoelectron spectroscopy, the nitrogen-modified Pt surface of Pt₃₀Fe₇₀N/OMC exhibits significant selectivity toward the ORR in the presence of methanol. This enhancement of methanol tolerance could be attributed to the inhibition of methanol adsorption resulting from the modification of the Pt surface with nitrogen.     

Binary-surfactant (Brij 35 + Tween 20) assisted preparation of highly dispersed Pt nanoparticles on carbon

Pt nanoparticles supported on Vulcan XC-72R, synthesized by a surfactant-stabilized colloidal method, exhibited excellent properties as anode catalyst for low-temperature fuel cell. The Pt/C catalyst prepared with binary-surfactant (Brij 35 + Tween 20) at 10 times CMC had an average particle size of 2.8 nm with quite a narrow distribution between 2 and 4 nm. Our preparation method resulted in complete reduction of Pt and full loading of Pt nanoparticles on the carbon. The home-made Pt/C catalyst showed higher EAS and better catalytic activity than a commercial Pt/C catalyst. The method used in this study provided an easy and reproducible procedure for the preparation of Pt nanoparticles supported on carbon.     

Synthesis of nanostructured lean-NO x catalysts by direct laser deposition of monometallic Pt-, Rh- and bimetallic PtRh-nanoparticles on SiO2 support

Monometallic Pt and Rh and bimetallic PtRh catalysts with a highly dispersed noble metal weight loading of ca. 1 wt% were produced via the direct deposition of nanoparticles on different SiO₂ supports by means of pulsed ultra-violet (248 nm) excimer laser ablation of Pt, Rh bulk metal and PtRh alloy targets. Backscattered electron microscopy (BSE), energy dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM) were employed to characterize the deposited nanoparticles, which were found to exhibit narrow size distribution centred around 2.5 nm. The catalytic activities for lean NO _x reduction of the monometallic and bimetallic catalyst samples were investigated in a flow reactor setup in the temperature range 100–400°C using a test gas mixture representative of oxygen rich diesel engine exhaust gas. For comparison a Rh/SiO₂ reference catalyst prepared by a conventional impregnation method was also tested. Further experiments were performed in which PtRh nanoparticles were deposited on a Rh/SiO₂ reference catalyst sample to study the possibility for controlled modification of its activity. The catalytic activity measurements revealed that among the samples solely prepared by laser deposition the PtRh–SiO₂ nanoparticle catalyst showed the highest activity for NO _x reduction at low temperatures 100–300°C. In addition, it could be demonstrated that the initially low NO _x reduction activity and the N₂ selectivity of the Rh/SiO₂ reference catalyst sample for temperatures below 250°C can be enhanced by post laser deposition of PtRh nanoparticles.     

Nanoparticles of Iron Nitride Encapsulated in Nitrogen-Doped Carbon Bulk Derived from Polyaniline/Fe2O3 Blends and Its Electrochemical Performance

Iron nitride nanoparticles encapsulated in nitrogen-doped carbon bulk is fabricated by a simple costep nitridation of Fe₂O₃ and carbonization of polyaniline. The microstructure and elemental composition of the materials are analyzed by transmission electron microscope, scanning electron microscope, X-ray diffraction, and X-ray photoelectron spectroscopy. The pore size distribution and specific surface area of the materials are identified using nitrogen adsorption and desorption method. The results illustrate that iron nitride nanoparticles with 5–20 nm in size are uniformly dispersed in the carbon bulk. The presence of carbon bulk effectively prevents the agglomeration of iron nitride nanoparticles, making the electrochemical performance of iron nitride nanoparticles/carbon nitride composite nanomaterials superior to that of pure iron nitride nanomaterials. At a current density of 0.5 A g⁻¹, the specific capacitance (257.5 F g⁻¹) of the iron nitride nanoparticles/nitrogen-doped carbon bulk is much higher than that (119.5 F g⁻¹) of pure iron nitride.     

Thermal stability of Pt nanoclusters interacting to carbon sublattice

The catalytic activity of Pt clusters is dependent not only on the nanoparticle size and its composition, but also on its internal structure. To determine the real structure of the nanoparticles used in catalysis, the boundaries of the thermal structure stability of Pt clusters to 8.0 nm in diameter interacting with carbon substrates of two types: a fixed α-graphite plane and a mobile substrate with the diamond structure. The effect of a substrate on the processes melting of Pt nanoclusters is estimated. The role of the cooling rate in the formation of the internal structure of Pt clusters during crystallization is studied. The regularities obtained in the case of “free” Pt clusters and Pt clusters on a substrate are compared. It is concluded that platinum nanoparticles with diameter D ≤ 4.0 nm disposed on a carbon substrate conserve the initial fcc structure during cooling.

     

Hierarchical Carbon‐Encapsulated Iron Nanoparticles as a Magnetically Separable Adsorbent for Removing Thiophene in Liquid Fuel

Hierarchical carbon‐encapsulated iron nanoparticles (Fe@Cs) with typical core/shell structure are successfully synthesized from starch and iron nitrate by an easy‐to‐handle process at different carbonization temperatures (600–1000 °C). The nanoparticles are characterized by transmission electron microscopy (TEM), X‐ray diffraction (XRD), nitrogen adsorption, and Fourier transform infrared spectroscopy (FTIR). The results show that the carbonization temperature has an important effect on the morphology, the core shape, the diameters, and the porous structure as well as performance of Fe@Cs. Fe@C samples carbonized at 900 °C (Fe@C‐900) show the relatively perfect quasi‐spherical bcc‐Fe core/carbon shell porous structure and their diameters are in a narrow range of 20–50 nm. The adsorption capabilities of Fe@C samples obtained at different carbonization temperatures for removal of thiophene from model oils are evaluated and compared in a batch‐type adsorption system. It has been found that among all of the samples measured, Fe@C‐900 shows the highest adsorption capability with an increase of 54% for thiophene in comparison with that of the commercial activated carbon. The feasibility of the as‐prepared Fe@C‐900 as a magnetically separable adsorbent is also demonstrated.     

Enhanced interfacial adhesion between PMMA and carbon fiber by graphene oxide coating

The purpose of this study is to increase the interfacial properties in PMMA/carbon fiber (PMMA/CF) composites Graphene oxide (GO) and brached polyethyleneimine were coated onto the surface of carbon fiber by layer-by-layer assembly in this work. Compared with the origin PMMA/CF composite, the composites reinforced by PMMA/CF–GO showed significant enhancement in interFacial shear strength (IFSS). The improved fiber–matrix adhesion was proved by fracture morphology observation of scanning electron microscopy and almost unaffected mechanical properties of the fiber itself during the coating process. The optimal assembly time was found to be 10 for enhancing the overall composite mechanical performance.     

Synthesis,characterization and mechanical properties of nylon–silver composite nanofibers prepared by electrospinning

Silver (Ag) nanoparticles (∼3 nm) were synthesized using silver nitrate as the starting precursor, ethylene glycol as solvent and poly (N-vinylpyrrolidone) (PVP) introduced as a capping agent. These nano-Ag particles were reinforced in nylon matrix by electrospinning of nylon-6/Ag solution in 2,2,2-trifluoroethanol and composite nanofibrous membranes were synthesized. The effects of solution concentration and relative humidity (RH) on the resultant fibrous membranes were studied. Scanning electron microscopy and Transmission electron microscopy was used to study the size and morphology of the fibers. It was observed that concentration and RH could be used to modulate the fiber diameter. Tensile test was used to evaluate the mechanical property of these electrospun composite membranes. The composite membranes showed higher strength (approx. 2–3 times increase in strength) compare to as synthesized nylon fibers.     

High-affinity integration of hydroxyapatite nanoparticles with chemically modified silk fibroin

Hydroxyapatite (HA)-based nanocomposites were prepared by a co-precipitation method with silk fibroin (SF) serving as organic matrix. Silk fibroin was chemically modified with an alkali solution or an enzyme attempting to improve the interface between the mineral and the organic matrix. The influences of the alkali and enzyme pretreatments on microstructure and physicochemical properties of HA–SF composite were examined and compared. The results reveal that both the two kinds of pretreatments facilitate the formation of highly ordered three-dimensional porous network throughout the composites, increase the microhardness of the composite, and promote the preferential growth of HA crystallites along c-axis. Among all the as-prepared samples, the composite containing the enzyme pretreated SF shows desirable hierarchical microstructure with higher degree of organization and more uniform pore size distribution. Due to the enzyme pretreatment, HA crystallites undergo obvious changes in morphology from rod-like to␣whisker-like and in crystal growth towards more apparent epitaxy along c-axis. The alkali pretreatment induces the stronger chemical interactions between HA and SF and thus to strengthen the inorganic–organic interfacial adhesion. The newly developed HA–SF composites are expected to be attractive biomedical materials for bone repair and remodeling.     

Interfacial interaction in carbon fiber/thermoplastic composites

This work was undertaken in order to increase the understanding of the mechanism responsible for fiber/matrix interaction in carbon fiber/thermoplastic composite. From results of previous study on carbon fiber/PEEK composite, which suggested that the formation of the fiber/ matrix interaction was primarily related to a chemisorption mechanism, a study was done of the conditions required to obtain efficient fiber/matrix interaction in PA-12 and PP/carbon fiber composites. The interest in studying carbon fiber composite based on PP and PA-12 was that these two matrices are very different in terms of reactivity, polyamide having many more reactive groups than polypropylene. As expected, due to the non-reactive chemical structure of the polypropylene, fiber/matrix interaction in carbon fiber/PP composite occurred only when the matrix was thermally degraded, i.e. when the composite was molded at high temperature or under long residence time at the melt temperature. For the carbon fiber/PA-12 composite, strong fiber/matrix interaction occurred readily at relatively low molding temperature, i.e. well before thermal degradation of the matrix. It was also found that the short beam shear strength in these composites seems to evolve with molding temperature, and a maximum interfacial strength was observed at a molding temperature corresponding to the thermal degradation of the matrix. This indicates that although matrix degradation often results in strong reduction in the composite performance, some matrix degradation can be beneficial in terms of interfacial mechanical properties. Finally, this work demonstrated that while the formation of fiber/matrix interaction seems to be primarily related to a chemisorption mechanism, the contribution of interphase crystallinity to the interfacial strength is not negligible. In fact, interfacial crystallinity was found to be essential to ensure optimum interfacial strength.     

Preparation of cholesterol oxidase nanoparticles and their application in amperometric determination of cholesterol

Highly dispersed platinum nanoparticles were deposited on gram quantities of non-functionalized multiwalled carbon nanotubes (MWCNTs) by atomic layer deposition (ALD) in a fluidized bed reactor at 300 °C. (Methylcyclopentadienyl) trimethylplatinum and oxygen were used as precursors. The results of TEM analysis showed that ~1.3 nm Pt nanoparticles were highly dispersed on non-functionalized MWCNTs. The porous structures of MWCNTs did not change with the deposition of Pt nanoparticles. For comparison, the commercial 3 wt% Pt/C catalyst was also characterized. The ALD-prepared Pt/MWCNT was used for the hydrogenation of xylose to xylitol. The ALD-prepared Pt/MWCNT showed the best catalytic performance with 100 % conversion of xylose and 99.3 % selectivity to xylitol, compared to commercially available Pt/C, Ru/C, and Raney Ni catalysts. The stability of ALD produced Pt/MWCNT catalyst was higher than that of the commercial Pt/C, due to the presence of surface defects on the MWCNTs and the strong metal–support interaction for the ALD-prepared Pt/MWCNT catalyst.     

Stabilization of Pt nanoparticles by single stranded DNA and the binary assembly of Au and Pt nanoparticles without hybridization

The non-specific interaction between single stranded DNA (ssDNA) and 12 nm Pt nanoparticles is investigated in this work. The data show a strong and non-specific interaction between the two which can be exploited for the stabilization of Pt nanoparticles in aqueous solutions. Based on the experimental findings, a non-hybridization based protocol to assemble 17 nm Au and Pt nanoparticles (12 nm cubic and 3.6 nm spherical) by single-stranded DNA was developed. Transmission electron microscopy (TEM) and UV–visible spectroscopy confirmed that Au and Pt nanoparticles could be assembled by the non-specific interaction in an orderly manner. The experimental results also caution against the potential pitfalls in using DNA melting point analysis to infer metal nanoparticle assembly by DNA hybridization.     

Sonoelectrochemical one-pot synthesis of Pt – Carbon black nanocomposite PEMFC electrocatalyst

Simultaneous electrocatalytic Pt-nanoparticle synthesis and decoration of Vulcan XC-72 carbon black substrate was achieved in a novel one-step-process, combining galvanostatic pulsed electrodeposition and pulsed ultrasonication with high power, low-frequency (20 kHz) ultrasound. Aqueous chloroplatinic acid precursor baths, as well as carbon black suspensions in the former, were examined and decoration was proven by a combination of characterization methods, namely: dynamic light scattering, transmission electron microscopy, scanning electron microscopy with EDX-analysis and cyclic voltammetry. In particular, PVP was shown to have a beneficial stabilizing effect against free nanoparticle aggregation, ensuring narrow size distributions of the nanoparticles synthesized, but is also postulated to prevent the establishment of a strong metal-substrate interaction. Current pulse amplitude was identified as the most critical nanoparticle size-determining parameters, while only small size particles, under 10 nm, appeared to be attached to carbon black.     

Cytotoxic evaluation of N-isopropylacrylamide monomers and temperature-sensitive poly(N-isopropylacrylamide) nanoparticles

The objective of this research project is to investigate the biocompatibility of N-isopropylacrylamide (NIPAAm) monomers and poly(N-isopropylacrylamide) (PNIPAAm) nanoparticles in vitro. PNIPAAm nanoparticles of different sizes were synthesized and characterized by transmission electron microscopy and dynamic light scattering. Cytotoxicity studies using MTS assays were conducted on fibroblasts, smooth muscle cells, and endothelial cells. In addition, the concentration of NIPAAm monomers remaining on PNIPAAm nanoparticles was determined using bromination and spectrophotometry. The cytotoxicity results did not show a significant difference in cell survival when cells were exposed to different particle sizes (100, 300, and 500 nm). Dose studies showed that all three cell types exposed to 100 nm PNIPAAm nanoparticles at concentrations less than or equal to 5 mg/mL were compatible, while cells exposed to NIPAAm monomers exhibited toxicity even at very low concentrations. We also found that 1 mg/mL concentration of 100 nm PNIPAAm nanoparticles was cytocompatible for 4 days, whereas NIPAAm monomers were cytotoxic after 24 h of exposure. Photomicrographs showed altered morphology in cells exposed to NIPAAm monomers, while cells exposed to PNIPAAm nanoparticles maintained their normal morphology. Finally, a very low concentration of NIPAAm monomers remained on the PNIPAAm nanoparticles after synthesis and dialysis. Our results demonstrate that NIPAAm monomers are cytotoxic, whereas PNIPAAm nanoparticles are compatible at 5 mg/mL concentration or below for fibrobasts, smooth muscle cells, and endothelial cells.     

Metal nanostructures with complex surface morphology: The case of supported lumpy Pd and Pt nanoparticles produced by laser processing of metal films

In this work we report on the formation of lumpy Pd and Pt nanoparticles on fluorine-doped tin oxide/glass (FTO/glass) substrate by a laser-based approach. In general, complex-surface morphology metal nanoparticles can be used in several technological applications exploiting the peculiarities of their physical properties as modulated by nanoscale morphology. For example plasmonic metal nanoparticles presenting a lumpy morphology (i.e. larger particles coated on the surface by smaller particles) can be used in plasmonic solar cell devices providing broadband scattering enhancement over the smooth nanoparticles leading, so, to the increase of the device efficiency. However, the use of plasmonic lumpy nanoparticles remains largely unexplored due to the lack of simply, versatile, low-cost and high-throughput methods for the controllable production of such nanostructures.Starting from these considerations, we report on the observation that nanoscale-thick Pd and Pt films (17.6 and 27.9 nm, 12.1 and 19.5 nm, respectively) deposited on FTO/glass surface irradiated by nanosecond pulsed laser at fluences E in the 0.5–1.5 J/cm² range, produce Pd and Pt lumpy nanoparticles on the FTO surface. In addition, using scanning electron microscopy analyses, we report on the observation that starting from each metal film of fixed thickness h, the fraction F of lumpy nanoparticles increases with the laser fluence E and saturates at the higher fluences. For each fixed fluence, F was found higher starting from the Pt films (at each starting film thickness h) with respect to the Pd films. For each fixed metal and fluence, F was found to be higher decreasing the starting thickness of the deposited film. To explain the formation of the lumpy Pd and Pt nanoparticles and the behavior of F as a function of E and h both for Pd and Pt, the thermodynamic behavior of the Pd and Pt films and nanoparticles due to the interaction with the nanosecond laser is discussed. In particular, the photothermal vaporization and Coulomb explosion processes of the Pd and Pt nanoparticles are invoked as possible mechanisms for the lumpy nanoparticles formation.     

Starch vermicelli template for synthesis of magnetic iron oxide nanoclusters

A novel method for fabricating magnetic iron oxide nanoparticles was achieved by using transparent vermicelli template as a new stabilizing material. The morphology of the as-prepared magnetic iron oxide deposited on the surface of vermicelli was observed as nanoclusters. The magnetization of the magnetic iron oxide nanoparticles at room temperature was decreased after carbonization at 200 °C. Therefore the thermal decomposition of iron oxide nanoparticles stabilized by starch vermicelli template yielded iron oxide/carbon nanocomposites with the soft magnetic behavior which are useful for biomedical applications.     

Photo-chemical synthesis and deposition of noble metal nanoparticles

Highly dispersed nanoparticles of transition and noble metals are utilized for hydrocarbon reactions and rearrangements important to the chemical industry. The need to obtain 1 to 3 nm particles with narrow size distributions has prompted the development of alternative processing methods. In this paper, a novel, dry method to synthesize nanoparticles from a frozen salt solution is reported. Pd nanoparticles were synthesized by photo-chemical decomposition of palladium acetate (PdAc) within a host matrix of chloroform using an excimer laser operating at 248 nm. Frozen composite targets were ablated at fluences ranging from 0.25 J/cm² to 0.75 J/cm² at a processing pressure of 10 mTorr. The ejected nanoparticles were deposited on continuous carbon coated and lacey carbon transmission electron microscopy (TEM) grids at ambient temperature. Characterization was performed by transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDXS). High-resolution TEM analysis showed definitive evidence that the size distributions of the nanoparticles were narrow, exhibiting mean diameters ranging from 2.15 nm to 2.62 nm. PACS 81.15.Fg; 68.37.Lp; 81.07.Wx; 81.07.Bc; 81.10.Dn