Efficient and stable single-dopant white OLEDs based on 9,10-bis (2-naphthyl) anthracene

Efficient white organic light-emitting diodes (WOLEDs) are fabricated with a thin layer of 9,10-bis (2-naphthyl) anthracene (ADN) doped with Rubrene as the source of white emission. A device with the structure of ITO/NPB (70 nm)/ADN: 0.5% Rubrene (30 nm)/Alq₃ (50 nm)/MgAg shows a maximum current efficiency of 3.7 cd/A, with the CIE coordinates of x=0.33, y=0.43. The EL spectrum of the devices and the CIE coordinates remains almost the same when the voltage is increased from 10 to 15 V and the current efficiency remains quite stable with the current density increased from 20 to 250 mA/cm².     

White organic electroluminescence from fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc doped with phosphorescent material

Efficient white electroluminescence has been obtained by using an electroluminescent layer comprising of a blue fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(hpb)₂] doped with red phosphorescent bis (2-(2′-benzothienyl) pyridinato-N,C^3′)iridium(acetylacetonate) [Ir(btp)₂acac] molecules. The color coordinates of the white emission spectrum was controlled by optimizing the concentration of red dopant in the blue fluorescent emissive layer. Organic light-emitting diodes were fabricated in the configuration ITO/α-NPD/Zn(hpb)₂:0.01 wt%Ir(btp)₂acac/BCP/Alq₃/LiF/Al. The J-V-L characteristic of the device shows a turn on voltage of 5 V. The electroluminescence (EL) spectra of the device cover a wide range of visible region of the electromagnetic spectrum with three peaks around 450, 485 and 610 nm. A maximum white luminance of 3500 cd/m² with CIE coordinates of (x, y=0.34, 0.27) at 15 V has been achieved. The maximum current efficiency and power efficiency of the device was 5.2 cd/A and 1.43 lm/W respectively at 11.5 V.     

Highly efficient greenish blue-emitting organic diodes based on pyrene derivatives

We report the synthesis of pyrene derivatives as the light emissive layer for highly efficient organic electroluminescence (EL) diodes. Multilayer devices were fabricated with pyrene derivatives (ITO/NPB (50 nm)/blue material (30 nm)/BCP (10 nm)/Alq₃ (30 nm)/LiF (1 nm)/Al). By using 1,1′-dipyrene (DP) and 1,4-dipyrenyl benzene (DPB), the devices produced the blue EL emissions with 1931 Commission International de L’Eclairage coordinates of (x=0.21, y=0.35) and (x=0.19, y=0.25), respectively. The device with DPB shows a maximum brightness of 42,445 cd/m² at 400 mA/cm² and the luminance efficiency of 8.57 cd/A and 5.18 lm/W at 20 mA/cm².     

Characterization of two-emitter WOLED with no additional blocking layer

In this paper, white organic light emitting diodes (WOLEDs) utilizing two primary-color emitters with no additional blocking layer are fabricated. With a structure of ITO/2TNATA (20 nm)/NPB (20 nm)/NPB: rubrene (2%) (10 nm)/ADN (30 nm)/Alq₃ (20 nm)/LiF (1 nm)/Al (100 nm), a white light with CIE coordinates of (0.344, 0.372) is generated at a current density of 30 mA/cm² and the electroluminescence (EL) spectra consist of two broad bands around 456 nm (ADN) and 556 nm (NPB:rubrene). The device shows the low turn-on voltage and bright white emission with a power efficiency of 2.3 lm/W at a luminance of 100 cd/m². Through control of the location of the recombination zone and energy transfer, a stable white light emission is achieved. The maximum color shift is less than 0.02 units on the 1931 CIE x,y chromaticity diagram. Given the spectral power distribution of WOLED, the parameters of a light source (chromaticity coordinate, CCT, CRI, and the luminous efficacy) can be calculated. A MATLAB program for this purpose is developed in this paper. Based on this, the design of WOLED for an illumination and display system using a white emitter with color filter arrays is discussed.     

White organic light emitting diodes based on DCM dye sandwiched in 2-methyl-8-hydroxyquinolinolatolithium

Stable white electroluminescence (EL) has been achieved from organic LED, in which an ultrathin 4-(dicyanomethylene)-2-methyl-6-(p-dimethyl-aminostyryl)-4H-pyran (DCM) dye layer has been inserted in between two 2-methyl-8-hydroxyquinolinolatolithium [LiMeq] emitter layer and by optimizing the position of the DCM dye layer from the α-NPD/LiMeq interface. Electroluminescence spectra, current-voltage-luminescence (I-V-L) characteristics of the devices have been studied by changing the position of the dye layer. As the distance of DCM layer from α-NPD/LiMeq interface is increased, the intensity of host emission enhances rapidly. Introduction of thin layer of DCM in emissive layer increases the turn on voltage. The best Commission International de L’ Eclairage (CIE) coordinates i.e. (0.32, 0.33) were obtained with device structure ITO/α-NPD(30 nm) /LiMeq(10 nm)/DCM(1 nm)/LiMeq(25 nm)/BCP(6 nm)/Alq₃(28 nm)/LiF(1 nm)/Al(100 nm). The EL spectrum covers the whole visible spectra range 400-700 nm. The color rendering index (CRI) for our best white light (Device 4) is 47.4. The device shows very good color stability in terms of CIE coordinates with voltages. The maximum luminescence 1240 cd/m⁻² has been achieved at 19 V.     

Efficient white organic light-emitting devices using 4,7-diphenyl-1,10-phenanthroline as block layer

A white light-emitting device has been fabricated with a structure of ITO/m-MTDATA (45 nm)/NPB (10 nm)/DPVBi (8 nm)/DPVBi:DCJTB 0.5% (15 nm)/BPhen (x nm)/Alq₃ [(55−x) nm]/LiF (1 nm)/Al, with x=0, 4, and 7. BPhen was used as the hole-blocking layer. This results in a mixture of lights from DPVBi molecules (blue-light) and DCJTB (yellow-light) molecules, producing white light emission. The chromaticity can be readily adjusted by only varying the thickness of the BPhen layer. The CIE coordinates of the device are largely insensitive to the driving voltages. When the thickness of BPhen is 7 nm, the device exhibits peak efficiency of 6.87 cd/A (3.59 lm/W) at the applied voltage of 6 V, the maximum external quantum efficiency η_ext=2.07% corresponding to 6.18 cd/A, and the maximum brightness is 18494 cd/m² at 15 V.     

Effects of hole injection layer thickness on the luminescent properties of white organic light-emitting diodes

This work investigates how the thickness of the hole injection layer (HIL) influences the luminescent characteristics of white organic light-emitting diodes (WOLED). Experimental results indicate that inserting a thin HIL (<200 Å) into a WOLED without an HIL reduces the brightness and clearly changes the chromaticity because the surface of the 4,4′,4″-tris{N,-(3-methylphenyl)-N-phenylamino}-triphenylamine) (m-MTDATA) film is extremely rough. In contrast, a dense film structure and the fine surface morphology of m-MTDATA of moderate thickness (350-650 Å) provides a uniform conducting path on which holes cross the indium tin oxide (ITO)/HIL interface, improving luminescent performance, associated with the relatively stable purity of the color of the emission, with Commission Internationale 1′Eclairage (CIE) coordinates of (x = 0.40, y = 0.40). However, inserting a thick HIL (>650 Å) reduces the luminescent performance and causes red-shift, because the holes and electrons in the effective emissive confinement region become less optimally balanced. Moreover, optimizing the device structure enables a bright WOLED with CIE coordinates of (x = 0.34, y = 0.33) to reach a luminance of 7685 cd/m² at a current density of 100 mA/cm², with a maximum luminous efficiency of 1.72 lm/W at 5.5 V.     

Efficient bright white organic light-emitting diode based on non-doped ultrathin 5,6,11,12-tetraphenylnaphthacene layer

High-performance undoped white organic light-emitting diode (OLED) has been fabricated using an ultrathin yellow-emitting layer of 5,6,11,12-tetraphenylnaphthacene (rubrene) inserted at two sides of interface between two N,N′-bis-(1-naphthyl)-N,N′- biphenyl-1,1′-biphenyl-4,4′- diamine (NPB) layers as a hole transporting and blue emissive layer, respectively. The results showed that a maximum luminance of the device reached to as high as 21,500 cd/m² at 15 V. The power efficiencies of 2.5 and 1.6 lm/W at a luminance of 1000 and 10000 cd/m², respectively, were obtained. The peaks of electroluminescent (EL) spectra locate at 429 and 560 nm corresponding to the Commissions Internationale De L’Eclairage (CIE) coordinates of (0.32, 0.33), which is independent of bias voltage. The performance enhancement of the device may result from direct charge carrier trapping in rubrene. Energy transfer mechanism was also found in the EL process.     

High efficiency small molecule white organic light-emitting devices with a multilayer structure

In this paper, a new white organic light-emitting device (WOLED) with multilayer structure has been fabricated. The structure of devices is ITO/N, N-bis-(1-naphthyl)-N, N^′-diphenyl-1, 1′-biphenyl-4, 4′-diamine (NPB) (40 nm)/NPB: QAD (1%): DCJTB (1%) (10 nm) /DPVBi (10 nm) /2, 9-dimethyl, 4, 7-diphenyl, 1, 10-phenanthroline (BCP) (d nm)/tris-(8-hydroxyquinoline) aluminium (Alq₃)(50-d nm)/LiF (1 nm)/Al (200 nm). In our devices, a red dye 4-(dicyanomethylene)-2-t-butyl-6 (1, 1, 7, 7-tetramethyl julolidyl-9-enyl)-4H-pyran (DCJTB) and a green dye quinacridone (QAD) were co-doped into NPB. The device with 8 nm BCP shows maximum luminance of 12 852 cd/m² at 20 V. The current efficiency and power efficiency reach 9.37 cd/A at 9 V and 3.60 lm/W at 8 V, respectively. The thickness of the blocking layer permit the tuning of the device spectrum to achieve a balanced white emission with Commission International de’Eclairage (CIE) chromaticity coordinates of (0.33,0.33). The CIE coordinates of device change from (0.3278, 0.3043) at 5 V to (0.3251, 0.2967) at 20 V that are well in the white region, which is largely insensitive to the applied bias.     

铱金属配合物磷光材料掺杂聚合物体系的电致发光特性

通过对一种新型贵金属铱的配合物磷光材料(pbi)₂Ir(acac)与咔唑共聚物进行物理掺杂, 制备了结构为indium-tin oxide(ITO)/poly(N-vinylcarbazole)(PVK): (pbi)₂Ir(acac)(x)/2,9-dimethyl-4,7-diphenyl-1,10-phenan throline(BCP)(20nm)/8-Hydroxyquinoline aluminum(Alq₃)(10nm)/Mg:Ag的聚合物电致磷光器件,研究了磷光聚合物掺杂体系在低掺杂浓度时(0.1%和0.5%(质量百分数,全文同))的光致发光(PL)和电致发光(EL)特性. 结果表明, 该掺杂体系的PL光谱和EL光谱中均同时存在主体材料PVK与磷光客体(pbi)₂Ir(acac)的发光光谱, 但主客体的发射强度不同,推测该掺杂体系在电致发光条件下, 同时存在主体材料到客体的不完全的能量传递和载流子直接俘获过程. 磷光掺杂浓度为0.1%的器件在19V电压下实现了白光发射, 色坐标为(0.32, 0.38), 掺杂浓度为0.5%的器件在20.6V电压下的最大发光亮度为11827 cd·m^-2, 而在13.4V电压下的最大流明效率为4.13 cd·A^-1. 关键词： 有机电致发光器件 铱配合物磷光 聚合物掺杂     

Low temperature deposition of SrS:Cu,F ACTFEL device by electron beam evaporation

Photoluminescence (PL) and electroluminescence (EL) of SrS:Cu,F alternating current thin film electroluminescent (ACTFEL) device prepared by electron beam/thermal multi-source evaporation are presented. The active layer was grown at 380 °C and neither post-deposition annealing nor sulphur co-evaporation was performed. Two bands at 380 and 435 nm were present in the PL spectrum, which are suggested to be due to donor acceptor recombination. EL spectrum consisted of an additional band at 535 nm, which is attributed to Cu⁺ intracenter emission. The device exhibited yellowish white EL emission with chromaticity coordinates x=0.25, y=0.27 and low threshold voltage.     

Ultraviolet electroluminescence from ZnO-based light-emitting diode with p-ZnO:N/n-GaN:Si heterojunction structure

A p-ZnO:N/n-GaN:Si structure heterojunction light-emitting diode (LED) is fabricated on c-plane sapphire by full metal organic chemical vapor deposition (MOCVD) technique. The p-type layer with hole concentration of 8.94×10¹⁶ cm⁻³ is composed of nitrogen-doped ZnO using NH₃ as the doping source with subsequent annealing in N₂O plasma ambient. Silicon-doped GaN film with electron concentration of 1.15×10¹⁸ cm⁻³ is used as the n-type layer. Desirable rectifying behavior is observed from the current-voltage (I-V) curve of the device. The forward turn on voltage is about 4 V and the reverse breakdown voltage is more than 7 V. A distinct ultraviolet (UV) electroluminescence (EL) with a dominant emission peak centered at 390 nm is detected at room temperature from the heterojunction structure under forward bias conditions. The origins of the EL emissions are discussed in comparison with the photoluminescence (PL) spectra.     

A terbium (III) complex with triphenylamine-functionalized ligand for organic electroluminescent device

A novel ligand, 4-diphenylamino-benzoic acid (HDPAB), and the corresponding Tb (III) complex, Tb (DPAB)₃ which can be dissolved easily in organic solvents were synthesized and characterized. Organic electroluminescent (EL) device with a structure of indium tin oxide (ITO)/poly(N-vinylcarbazole) (PVK): Tb (DPAB)₃ (50 wt%, 80 nm)/1,3,5-tris-(N-phenylbenzimidazol-2-yl)benzene (TPBI) (30 nm)/tri(8-hydroxyquinoline)aluminum (AlQ) (20 nm)/LiF (1 nm)/Al (150 nm) in which Tb (DPAB)₃ acted as an emitter were fabricated. The maximum luminance of 230 cd m⁻² at 20 V and the maximum efficiency of 0.62 cd A⁻¹ were obtained due to the introduction of hole-transporting group, representing the best result to date among Tb (III) carboxylate complexes based EL devices. These results indicate that modifications of rare earth complexes are a promising way to improve the properties of EL devices.     

Effect of SiO2/Si3N4 dielectric distributed Bragg reflectors (DDBRs) for Alq3/NPB thin-film resonant cavity organic light emitting diodes

In this article, we report on the effect of SiO₂/Si₃N₄ dielectric distributed Bragg reflectors (DDBRs) for Alq₃/NPB thin-film resonant cavity organic light emitting diode (RCOLED) in increasing the light output intensity and reducing the linewidth of spontaneous emission spectrum. The optimum DDBR number is found as 3 pairs. The device performance will be bad by further increasing or decreasing the number of DDBR. As compared to the conventional Alq₃/NPB thin-film organic light emitting diode (OLED), the Alq₃/NPB thin-film RCOLED with 3-pair DDBRs has the superior electrical and optical characteristics including a forward voltage of 6 V, a current efficiency of 3.4 cd/A, a luminance of 2715 cd/m² under the injection current density of 1000 A/m², and a full width at half maximum (FWHM) of 12 nm for emission spectrum over the 5-9 V bias range. These results represent that the Alq₃/NPB thin-film OLED with DDBRs shows a potential as the light source for plastic optical fiber (POF) communication system.     

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile

A new compound with intramolecular charge transfer (ICT) property—5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both “positive” and “negative” solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N′-diphenyl-N,N′-bis-(3-methylphenyl) (1,1′-diphenyl)4,4′-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m² at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m² at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m² at 4.5 V, a maximum brightness of 12600 cd/m² at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A.     

Electronic and interface state density distribution properties of Ag/p-Si Schottky diode

Electronic and interface state distribution properties of Ag/p-Si Schottky diode have been investigated. The diode indicates non-ideal current-voltage behavior with an ideality factor greater than unity. The capacitance-voltage (C-V) characteristic is linear in reverse bias indicating rectification behavior and charge density within depletion layer is uniform. From I-V and C-V characteristics, junction parameters such as diode ideality factor and barrier height were found as 1.66 and ?_B(I-V) = 0.84 eV (?_B(C-V) = 0.90 eV), respectively. The interface state density N_ss and relaxation time τ of the Schottky diode were determined by means of Schottky capacitance spectroscopy method. The results show the presence of thin interfacial layer between the metal and semiconductor.     

Enhanced luminescence of Ca3B2O6:Dy phosphors by Na-codoping for LED applications

The Ca_2.95−yDy_0.05B₂O₆:yNa⁺ (0≤y≤0.20) phosphors were synthesized at 1100 °C in air by the solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE), photoluminescence (PL) spectra and thermoluminescence (TL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid-state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions on 350 nm excitation was observed at 480 nm (blue) due to the ⁴F_9/2→⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2→⁶H_13/2 transitions and 660 nm (red) due to weak ⁴F_9/2→⁶H_11/2 emissions. The PL results from the investigated Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors show that Dy³⁺ emissions increase with the increase of the Na⁺ codoping ions. The integral intensity of yellow to blue (Y/B) can be tuned by controlling Na⁺ content. By the simulation of white light, the optimal CIE value (0.328, 0.334) can be achieved when the content of Na⁺-codoping ions is y=0.2. The results imply that the Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors could be potentially used as white LEDs.     

Bright electrophosphorescent devices based on sterically hindered spacer-containing Cu(I) complex

A Cu(I) complex, [Cu(Dppp)(DPEphos)]BF₄ (Dppp=2,3-diphenyl-pyrazino[2,3-f][1,10]phenanthroline, DPEphos=Bis[2-(diphenylphosphino)phenyl]ether), is synthesized and used as the dopant in bright electrophosphorescent devices with the general structure ITO/m-MTDATA (30 nm)/NPB (20 nm)/CBP: ×wt% [Cu(Dppp)(DPEphos)]BF₄ (30 nm)/Bphen (20 nm)/Alq₃ (20 nm)/LiF (0.8 nm)/ Al (200 nm). These devices exhibit a maximum brightness of 4483 cd/m² and a peak efficiency of 3.4 cd/A. Compared with previously reported similar devices based on Cu(I) complexes, the brightness of the devices presented in this article is the best. Meanwhile, 2% [Cu(Dppp)(DPEphos)]BF₄-based devices exhibit white light-emitting properties with CIE coordinates of (0.32. 0.35) at 10 V.     

Synthesis and electroluminescent properties of a carbozole-functionalized europium(III) complex

A novel europium(III) complex, tris(dibenzoylmethanate){1-[9-hexyl-9H-carbazole]-2-(2-pyridyl)-benzimidazole}europium(III) [Eu(DBM)₃(CAR-PyBM)] functionalized by a carbozole fragment, was synthesized and used as emitting material in organic electroluminescent (EL) devices. Compared with the device based on an unfunctional Eu(III) complex, [Eu(DBM)₃HPyBM] (HPyBM=2-(2-pyridyl)benzimidazole), the EL performances of the device using [Eu(DBM)₃(CAR-PyBM)] as an emitter was significantly enhanced due to the improvement of hole-transporting ability. The maximum efficiency and luminance of red emission achieved from the device with the configuration of ITO/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′diamine (TPD, 50 nm)/ [Eu(DBM)₃(CAR-PyBM)] (30 nm)/1,3,5-tirs-(N-phenylbenzimidazol-2-yl)benzene (TPBI, 20 nm)/LiF (1.5 nm)/Al were 4.2 cd/A and 200 cd/m², respectively.     

New double graded structure for enhanced performance in white organic light emitting diode

This study presents a new design that uses a combination of a graded hole transport layer (GH) structure and a gradually doped emissive layer (GE) structure as a double graded (DG) structure to improve the electrical and optical performance of white organic light-emitting diodes (WOLEDs). The proposed structure is ITO/m-MTDATA (15 nm)/NPB (15 nm)/NPB: 25% BAlq (15 nm)/NPB: 50% BAlq (15 nm)/BAlq: 0.5% Rubrene (10 nm)/BAlq: 1% Rubrene (10 nm)/BAlq: 1.5% Rubrene (10 nm)/Alq₃ (20 nm)/LiF (0.5 nm)/Al (200 nm). (m-MTDATA: 4,4′,4″ -tris(3-methylphenylphenylamino)triphenylamine; NPB: N,N′-diphenyl-N,N′-bis(1-naphthyl-phenyl)-(1,1′-biphenyl)-4,4′-diamine; BAlq: aluminum (III) bis(2-methyl-8-quinolinato) 4-phenylphenolate; Rubrene: 5,6,11,12-tetraphenylnaphthacene; Alq₃: tris-(8-hydroxyquinoline) aluminum). By using this structure, the best performance of the WOLED is obtained at a luminous efficiency at 11.8 cd/A and the turn-on voltage of 100 cd/m² at 4.6 V. The DG structure can eliminate the discrete interface, and degrade surplus holes, the electron-hole pairs are efficiently injected and balanced recombination in the emissive layer, thus the spectra are unchanged under various drive currents and quenching effects can be significantly suppressed. Those advantages can enhance efficiency and are immune to drive current density variations.