Effect of surface species on Cu-TiO2 photocatalytic activity

The Cu-TiO₂ nanoparticles with different Cu dopant content were prepared by sol-gel method. The structure of the as-prepared catalysts and the surface species of Cu-TiO₂ were determined using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and diffuse reflection spectroscopy (DRS). The relationship between the photocatalytic activity and the surface species of Cu-TiO₂ was revealed via the measurement of surface photovoltage spectroscopy (SPS) as well as the degradation of the rhodamine B (RhB). The experimental results suggest that the Cu-TiO₂ photocatalysts with appropriate content of Cu (about 0.06 mol%) possess abundant electronic trap, which effectively inhibits the recombination of photoinduced charge carriers, improving the photocatalytic activity of TiO₂. While at high Cu dopant region (>0.06 mol%), the excessive oxygen vacancies and Cu species can become the recombination centers of photoinduced electrons and holes. Meanwhile, at heavy Cu doping concentration, excessive P-type Cu₂O can cover the surface of TiO₂, which leads to decrease in the photocatalytic activity of photocatalyst. The photocatalytic experimental results are in good agreement with the conclusions of SPS measurements, indicating that there is a close relationship between the photocatalytic activity and the intensity of SPS spectra.     

Preparation of nanocrystalline Sn-TiO2−X via a rapid and simple stannous chemical reducing route

The Sn-TiO_2−X nanoparticles have been prepared via a rapid and simple stannous chemical reducing method. The as-prepared Sn-TiO_2−X nanoparticles were investigated by means of surface photovoltage spectroscopy (SPS), XPS, and DRS technology as well as photocatalytic degradation of RhB were studied under illumination. The experiment results revealed that the reduction of the TiO₂ particles raised their Fermi level, which can enhance the driven force of photoinduced electrons transferring from TiO₂ to adsorbed O₂ and SnO₂ on the surface of TiO₂. On the other hand, the amount of oxygen vacancies of the Sn-TiO_2−X increased after the stannous chemical reduction. The oxygen vacancies can also effectively inhibit the recombination of photoinduced electrons and holes pairs. These factors are favorable to the photocatalytic reaction.     

The preparation and characterization of nanoparticle TiO2/Ti films and their photocatalytic activity

Nanoparticle TiO₂/Ti films were prepared by a sol–gel process using Ti(OBu)₄ as raw material, the as-prepared film samples were also characterized by TG-DTA, XRD, TEM, SEM, XPS, DRS, PL, SPS and EFISPS testing techniques. TiO₂ nanoparticles experienced two processes of phase transition, i.e. amorphous to anatase and anatase to rutile at the calcining temperature range from 450 to 700 °C. TiO₂ nanoparticles calcined at 600 °C had similar composition, structure, morphology and particle size with the internationally commercial P-25 TiO₂ particles. Thus, the conclusion that 600 °C might be the most appropriate calcining temperature during the preparation process of nanoparticle TiO₂/Ti film photocatalysts could be made by considering the main factors such as the properties of TiO₂ nanoparticles, the adhesion of nanoparticle TiO₂ film to Ti substrate, the effects of calcining temperature on Ti substrate and the surface characteristics and morphology of nanoparticle TiO₂/Ti film for the practice view. The Ti element mainly existed on the nanoparticle TiO₂/Ti(3) film calcined at 600 °C as the chemical state of Ti⁴⁺, while O element mainly existed as three kinds of chemical states, i.e. crystal lattice oxygen, hydroxyl oxygen and adsorbed oxygen with increasing band energy. Its photoluminescence (PL) spectra with a peak at about 380 nm could be observed using 260 nm excitation, possibly resulting from the electron transition from the bottom of conduction band to the top of valence band. The PL peak position was nearly the same as the onset of its diffuse reflection spectra (DRS) and surface photovoltage spectroscopy (SPS), demonstrating that the effects of the quantum size on optical property were greater than that of the Coulomb and surface polarization. The PL spectra with two peaks related to the anatase and rutile, respectively, could be observed using the excited wavelength of 310 nm. Weak PL spectra could be observed using the excited wavelength of 450 nm, resulting from surface states. In addition, during the experimental process of the photocatalytic degradation phenol, the photocatalytic activity of nanoparticle TiO₂/Ti film with three layers calcined at 600 °C was the highest.     

Effect of surface ethoxy groups on photoactivity of TiO2 nanocrystals

TiO₂ nanocrystals modified by ethoxy groups were prepared by a facile nonhydrolytic solvothermal method and characterized by XRD, TEM, TG-DTA and XPS, which showed an enhanced visible-light photocatalytic activity on the degradation of Rhodamine B compared with TiO₂ modified by benzyloxy groups and the “naked” TiO₂. The adsorption and degradation pathway of Rhodamine B on TiO₂ modified by ethoxy groups were also investigated. The zeta-potential (ζ) results showed that the TiO₂ modified by ethoxy groups had high negative surface charge, which incited the positive -N(Et)₂ group of RhB absorbing on the TiO₂ surface and preferably led the N-dealkylation pathway under visible light irradiation.     

Graphene oxide based Pt-TiO2 photocatalyst: ultrasound assisted synthesis, characterization and catalytic efficiency

An ultrasound-assisted method was used for synthesizing nanosized Pt-graphene oxide (GO)-TiO₂ photocatalyst. The Pt-GO-TiO₂ nanoparticles were characterized by diffused reflectance spectroscopy, X-ray diffraction, N₂ BET adsorption-desorption measurements, atomic force microscopy and transmission electron microscopy. The photocatalytic and sonophotocatalytic degradation of a commonly used anionic surfactant, dodecylbenzenesulfonate (DBS), in aqueous solution was carried out using Pt-GO-TiO₂ nanoparticles in order to evaluate the photocatalytic efficiency. For comparison purpose, sonolytic degradation of DBS was carried out. The Pt-GO-TiO₂ catalyst degraded DBS at a higher rate than P-25 (TiO₂), prepared TiO₂ or GO-TiO₂ photocatalysts. The mineralization of DBS was enhanced by a factor of 3 using Pt-GO-TiO₂ compared to the P-25 (TiO₂). In the presence of GO, an enhanced rate of DBS oxidation was observed and, when doped with platinum, mineralization of DBS was further enhanced. The Pt-GO-TiO₂ catalyst also showed a considerable amount of degradation of DBS under visible light irradiation. The initial solution pH had an effect on the rate of photocatalytic oxidation of DBS, whereas no such effect of initial pH was observed in the sonochemical or sonophotocatalytic oxidation of DBS. The intermediate products formed during the degradation of DBS were monitored using electrospray mass spectrometry. The ability of GO to serve as a solid support to anchor platinum particles on GO-TiO₂ is useful in developing new photocatalysts.     

Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Properties of carbon and iron modified TiO2 photocatalyst synthesized at low temperature and photodegradation of acid orange 7 under visible light

The nanoparticles of TiO₂ modified with carbon and iron were synthesized by sol-gel followed solvothermal method at low temperature. Its chemical composition and optical absorption were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence emission spectroscopy (PL), UV-vis absorption spectroscopy, and electron paramagnetic resonance (EPR). It was found that carbon and iron modification causes the absorption edge of TiO₂ to shift the visible light region. Fe(III) cation could be doped into the matrix of TiO₂, by which could hinder the recombination rate of excited electrons/holes. Superior photocatalytic activity of TiO₂ modified with carbon and iron was observed for the decomposition of acid orange 7 (AO7) under visible light irradiation. The synergistic effects of carbon and iron in modified TiO₂ nanoparticles were responsible for improving visible light photocatalytic activity.     

DBS包覆TiO2纳米粒子的表面光伏及光致发光性能

采用溶胶-水热法合成了十二烷基苯磺酸钠(DBS)包覆的TiO2纳米粒子,并利用X射线衍射仪、透射电镜、表面光电压谱(SPS)和光致发光光谱(PL)等对样品进行表征.重点探讨了DBS包覆的适宜条件及DBS包覆对TiO2光伏和发光等性质的影响.结果表明,进釜前pH值在4.5~5.5,DBS用量为TiO2质量的1.0%~3.0%时,能够获得理想包覆.在水热过程中,DBS的引入对锐钛矿型TiO2微晶的生长有抑制作用.由于DBS的包覆,使TiO2的SPS和PL信号强度显著下降,这可能与磺酸基的吸电子性以及表面缺陷等的减少有关.     

Photocatalytic properties of porous C-doped TiO2 and Ag/C-doped TiO2 nanomaterials by eggshell membrane templating

Porous organic carbon-doped titania (C-TiO₂) nanomaterials and their composites with Ag nanoparticles (Ag/C-TiO₂) were synthesized by an eggshell membrane templating method, and their structural and photocatalytic properties were systematically characterized. These nanomaterials, exhibiting a macroscopic morphology of a thin film, are composed of interwoven tubes, and the tube wall consists of nanocrystals. The doped organic carbon was composed of the active carbon and carbonate species, which could form a layer around the surface of TiO₂ nanoparticles, while the silver was incorporated into Ag/C-TiO₂ composites as separated Ag nanoparticles. The degradation of methylene blue under visible light irradiation was employed to evaluate the photocatalytic activity of these as-prepared TiO₂-based materials. Both C-TiO₂ and Ag/C-TiO₂ nanomaterials showed higher photocatalytic activity than pure TiO₂ material–commercial Degussa P25. These results can be accounted for the coupling effect of the incorporation of carbon species and Ag nanoparticles.     

Graphene-based hollow TiO2 composites with enhanced photocatalytic activity for removal of pollutants

Catalytically active graphene-based hollow TiO₂ composites(TiO₂/RGO) were successfully synthesized via the solvothermal method. Hollow TiO₂ microspheres are uniformly dispersed on RGO. X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV–vis diffuse reflectance spectroscopy (DRS) and photoluminescence (PL) were used for the characterization of prepared photocatalysts. The mass of GO was optimized in the photocatalytic removal of rhodamine B (RhB) as a model dye pollutants. The results showed that graphene-based hollow TiO₂ composites exhibit a significantly enhanced photocatalytic activity in degradation of RhB under either UV or visible light irradiation. The formation of the graphene-based hollow TiO₂ composites and the photocatalytic mechanisms under UV and visible light were also discussed.