18 MeV质子辐照对TiNi形状记忆合金R相变的影响

 研究了用HZ-B串列加速器的18MeV质子辐照对TiNi形状记忆合金R相变的影响，辐照在奥氏体母相状态下进行。示差扫描量热法（DSC）表明，辐照后R相变开始温度T^s_R和逆马氏体相变结束温度T^f_A随辐照注量的增加而降低。当注量为1.53×10¹⁴/cm²时，T^sR和T^f_A分别下降6K和13K，辐照未引起R相变结束温度T^s_R和逆马氏体相变开始温度T^f_A的变化。表明辐照后母相(奥氏体相)稳定。透射电镜（TEM）分析表明辐照后没有引起合金可观察的微观组织变化。辐照对R相变开始温度T^s_{R和逆马氏体相变结束温度Af的影响可能是由于质子辐照后产生了孤立的缺陷团，形成了局部应力场，引起晶格有序度的下降所造成的。}     

60keV质子辐照对TiNi记忆合金薄膜马氏体相变的影响

利用磁控溅射的方法在氧化后的单晶Si基片上制备了TiNi形状记忆合金薄膜，利用示差扫描量热法和原位X射线衍射研究了薄膜的马氏体相变特征。通过60keV质子注入（辐照）薄膜样品研究了H+离子对合金薄膜马氏体相变特征的影响，结果表明氢离子注入后引起了马氏体相变开始Ms和结束点Mf以及逆马氏体相变开始As和结束温度Af的下降，而对R相变开始Rs和结束温度Rf影响不大。掠入射X射线衍射表明H+离子注入后有氢化物形成。H+离子注入形成的氢化物是引起相变点的变化的主要因素。     

60keV质子辐照对TiNi记忆合金薄膜马氏体相变的影响

 利用磁控溅射的方法在氧化后的单晶Si基片上制备了TiNi形状记忆合金薄膜，利用示差扫描量热法和原位X射线衍射研究了薄膜的马氏体相变特征。通过60keV质子注入（辐照）薄膜样品研究了H+离子对合金薄膜马氏体相变特征的影响，结果表明氢离子注入后引起了马氏体相变开始Ms和结束点Mf以及逆马氏体相变开始As和结束温度Af的下降，而对R相变开始Rs和结束温度Rf影响不大。掠入射X射线衍射表明H+离子注入后有氢化物形成。H⁺离子注入形成的氢化物是引起相变点的变化的主要因素。     

冲击诱发NiTi形状记忆合金相变行为研究

NiTi形状记忆合金的高应变动态响应特性在军事、航空等领域具有重要应用.为研究NiTi合金在动态力学诱导下的相变行为,在不同温区不同冲击速率下,通过轻气炮装置对NiTi合金进行了动态加载实验.利用差示扫描量热仪(DSC),综合物性测量系统分析了冲击波残余效应对NiTi合金相变行为的影响.研究发现:受冲击的样品在第一次DSC热循环中观察到了三个马氏体吸热峰,表现为三步逆马氏体相变,而在第二次热循环中其中两个应力诱发马氏体吸热峰因变形恢复消失.形成两个应力诱发马氏体吸热峰的原因可能是晶粒内部与晶界处的相变过程不同步.受冲击后样品DSC放热峰上出现了一小肩峰,表明可能因中间相(R相)的出现而发生了两步相变,结合电阻测量曲线进一步确认R相的存在,且发现奥氏体相向R相转变以及R相向马氏体相转变这两种相变过程在某一温度范围内可同时进行.同时,文中也具体讨论了不同的冲击加载条件对相变过程的影响.     

深冷温区应变强化S30408奥氏体不锈钢马氏体相变研究北大核心

对S30408奥氏体不锈钢进行室温应变强化,在深冷温区(77K^4.2K)进一步时效处理,利用金相显微镜、X射线衍射仪(XRD)和透射电子显微镜(TEM)研究了应变诱发和热诱发马氏体相变的微观特征,探讨了马氏体相变的微观机理。结果表明:马氏体相变的含量、微观形貌、形核特征和位错组态随着预应变量的增加和温度的降低而改变,且应变强化比温度对相变的影响要大。诱发马氏体与母相奥氏体的位相关系符合K-S关系,其相变的微观机理为γ(fcc)→ε(hcp)、γ(fcc)→α'(bcc)、γ(fcc)→ε(hcp)→α'(bcc)、γ(fcc)→形变孪晶→α'(bcc)。     

深冷温区应变强化S30408奥氏体不锈钢马氏体相变研究

对S30408奥氏体不锈钢进行室温应变强化,在深冷温区(77K~4.2K)进一步时效处理,利用金相显微镜、X射线衍射仪(XRD)和透射电子显微镜(TEM)研究了应变诱发和热诱发马氏体相变的微观特征,探讨了马氏体相变的微观机理。结果表明:马氏体相变的含量、微观形貌、形核特征和位错组态随着预应变量的增加和温度的降低而改变,且应变强化比温度对相变的影响要大。诱发马氏体与母相奥氏体的位相关系符合K-S关系,其相变的微观机理为γ(fcc)→ε(hcp)、γ(fcc)→α'(bcc)、γ(fcc)→ε(hcp)→α'(bcc)、γ(fcc)→形变孪晶→α'(bcc)。     

利用内耗研究淬火空位对Cu-11.9Al-2.5Mn(wt%)形状记忆合金逆马氏体相变温度的影响

利用内耗手段研究了淬火空位的演变行为及其对Cu-11.9Al-2.5Mn(wt%)形状记忆合金逆马氏体相变温度的影响.通过对不同冷却方式的样品研究表明，较高的冷却速度可以导致较高的逆马氏体相变峰峰温.而对于水淬样品，相变峰峰温随淬火温度呈非单调变化行为，这可能与有序相及无序相中不同的空位形成能有关.经历热循环以后，逆马氏体相变峰峰温显著降低. 关键词： 形状记忆合金 热处理 马氏体相变 阻尼     

Ti-50.8at%Ni马氏体相变中的电磁特性

研究Ti-50.8at%Ni合金在马氏体-奥氏体相变温度附近的电磁性质.由M-H曲线分析了传导电子的顺磁性以及少量局域电子引起的铁磁性.在M-T曲线中，降温曲线在180K附近有突降，升温曲线在230K附近有突升.在电阻率测量中，降温和升温的ρ-T曲线也有类似的突变.升温过程的质量热容c_p曲线在230K附近出现了由奥氏体相变引起的跳跃.这些实验结果表明，样品的马氏体相变温度约 关键词： TiNi合金 电磁性质 马氏体-奥氏体相变 质量热容     

低温时效处理对铁磁形状记忆合金Mn2NiGa的结构、相变和磁性能的影响

对在较低温度范围的时效处理铁磁形状记忆合金Mn₂NiGa的结构、相变和磁性进行了研究.研究发现,母相基体析出了细小的析出相,引起了晶格扭曲和畸变,导致了系统内产生了很大的内应力.在其浓度超过晶格的容忍度之后,提升了体系的马氏体相变温度,使母相在时效温度下转变成马氏体相,并在其中测量到高达900 Oe的矫顽力.由于这种马氏体相的逆相变温度大幅提高,外推获得其居里温度在530 K附近.细小析出相的粗化使内应力消失,样品又回到母相状态.观察到细小析出相粗化的两个阈值温度,分别为423 K和 关键词： 铁磁形状记忆合金 2NiGa')" href="#">Mn₂NiGa 时效处理 内应力     

Cu含量对Ni_(55)Fe_(18)Ga_(27)合金结构和磁性的影响

系统研究了Cu分别替代Fe和Ni对Ni_(55)Fe_(18)Ga_(27)结构和磁性的影响.结果表明:熔炼Ni_(55)Fe_(18-x)Cu_(x )Ga_(27)(x=1,2,3,4)虽仍为奥氏体相结构,但伴有γ相出现;居里温度随Cu含量增加而降低,这是由于Cu掺杂引起过渡金属近邻原子间相互交换作用减弱所致;交流磁化率随Cu含量增加而降低,原因在于Fe是磁性的主要贡献者,Cu替代Fe会削弱Fe的磁矩,从而导致合金磁性降低.熔炼、退火和甩带Ni_(51)Cu_4Fe_(18)Ga_(27)均存在马氏体相变.熔炼样品马氏体相变温度最高,退火和甩带样品基本相同.这一特点表明热处理方式能够改变原子排列的有序度,因此可以通过改变热处理方式来调控马氏体相变温度.     

Mechanical response of proton beam irradiated nitinol

The present investigation deals with the study of mechanical behavior of proton beam irradiated nitinol at room temperature. The specimens in austenitic phase were irradiated over periods of 15, 30, 45 and 60 min at room temperature using 2 MeV proton beam obtained from Pelletron accelerator. The stress-strain curves of both unirradiated and irradiated specimens were obtained using a universal testing machine at room temperature. The results of the experiment show that an intermediate rhombohedral (R) phase has been introduced between austenite and martensite phase, which resulted in the suppression of direct transformation from austenite to martensite (A-M). Stresses required to start R-phase (σ_RS) and martensitic phase (σ_MS) were observed to decrease with increase in exposure time. The hardness tests of samples before and after irradiation were also carried out using Vickers hardness tester. The comparison reveals that the hardness is higher in irradiated specimens than that of the unirradiated one. The increase in hardness is quite sharp in specimens irradiated for 15 min, which then increases linearly as the exposure time is increased up to 60 min. The generation of R-phase, variations in the transformation stresses σ_RS and σ_MS and increase in hardness of irradiated nitinol may be attributed to lattice disorder and associated changes in crystal structure induced by proton beam irradiation.     

Twin evolution near the phase transformation of In77.5Tl22.5

The evolution of the martensitic twin microstructure in In_77.5Tl_22.5 single crystals was investigated by atomic force microscopy. During the reverse martensitic transformation the twins gradually flatten to disappear completely at the austenite finish temperature. The experimentally determined temperature dependence of the height of the twin profile agrees with the theoretical predictions of Barsch and Krumhansl.     

Effects of Cu on the martensitic transformation and magnetic properties of Mn_(50)Ni_(40)In_(10) alloy

The structures, the martensitic transformations, and the magnetic properties are studied systematically in Mn50Ni40-xCuxIn10, Mn50-xCuxNi40In10, and Mn50Ni40In10-xCux alloys. The partial substitution of Ni by Cu reduces the martensitic transformation temperature, but has little influence on the Curie temperature of austenite. Comparatively, the martensitic transformation temperature increases and the Curie temperature of austenite decreases with the partial replacement of Mn or In by Cu. The magnetization difference between the austenite phase and the martensite phase reaches 70 emu/g in Mn50Ni39Cu1In10; a field-induced martensite-to-austenite transition is observed in this alloy.     

铝对过渡金属离子掺杂的二氧化硅溶胶凝胶玻璃发光性质的影响

用溶胶凝胶法制备了过渡金属离子(Ni2+,Mn2+和Cu2+)单掺、铝共掺的二氧化硅玻璃,测量了荧光光谱、吸收光谱和红外光谱,研究了Al3+对过镀金属离子在二氧化硅玻璃中发光性质的影响。研究结果表明,Al3+对过渡金属离子的发光性质有着显著影响:Ni2+,Mn2+和Cu+的发光强度大幅度提高,Mn2+的发光峰峰位改变。     

Phase transformation studies in unirradiated and proton beam irradiated Ni–Ti alloy between 25 and 100°C

The stress-induced phase transformation characteristics of unirradiated and proton beam irradiated NiTi alloy were investigated at different tests temperatures. The wire-shaped NiTi specimens were irradiated by 2?MeV proton beam for 30?min at room temperature to a flux of 10¹⁹ protons/m² s. Engineering stress–strain (S-S) curves of both unirradiated and irradiated specimens were obtained using a materials testing machine at 25, 50, 75 and 100°C. The results indicate a single-stage phase transformation from austenite to martensite (B2–B19′) in unirraidated specimens at all the test temperatures. In contrast, in the case of the irradiated specimens, a two-stage austenite–rhombohedral–martensite (B2–R–B19′) phase transformation is observed at 25 and 50°C. The B2–R–B19′ phase transformation, however, is found to change into B2–B19′ transformation at 75 and 100°C. The stress required to initiate the B19′ phase transformation (σ_MS) and the plateau range are found to be lower in irradiated specimens compared with those of the unirradiated specimens. The results obtained are discussed on the basis of the formation of Ni₄Ti₃ precipitates in irradiated specimens and their consequences on the phase transformations.     

The effect of Si content on the martensitic transfor-mation temperature of Ni55.5e18Ga26.5-xSix alloys

This paper investigates the effects of substitution of Si for Ga on the martensitic transformation behaviours in Ni-Fe-Ga alloys by using optical metallographic microscope and differential scanning calorimetry (DSC) methods. The structure type of Ni_55.5Fe₁₈Ga_26.5-xSi_x alloys is determined by x-ray diffraction (XRD), and the XRD patterns show the microstructure of Ni-Fe-Ga-Si alloys transformed from body-centred tetragonal martensite (with Si content x = 0) to body-centred cubic austenite (with x = 2) at room temperature. The martensitic transformation temperatures of the Ni_55.5Fe₁₈Ga_26.5-xSi_x alloys decrease almost linearly with increasing Si content in the Si content range of x ≤ 3. Thermal treatment also plays an important role on martensitic transformation temperatures in the Ni-Fe-Ga-Si alloy. The valence electronic concentrations, size factor, L2₁ degree of order and strength of parent phase influence the martensitic transformation temperatures of the Ni-Fe-Ga-Si alloys. An understanding of the relationship between martensitic transformation temperatures and Si content will be significant for designing an appropriate Ni-Fe-Ga-Si alloy for a specific application at a given temperature.