A four-wavelength depolarization backscattering LIDAR for polar stratospheric cloud monitoring

A four wavelength backscattering depolarization LIDAR designed for polar stratospheric cloud and stratospheric aerosol measurement is described. The system uses the following wavelengths: 355 nm, 532 nm, 750 nm, and 850 nm. These wavelengths, obtained by means of the third- and second-harmonic of a Nd: YAG laser and by means of a tunable Ti: Sapphire laser, are chosen in a way to better characterize the particel size of such stratospheric aerosols. They are not emitted simultaneously as the LIDAR system is designed with only two detection channels permitting to detect, in the analog and in the photon counting mode, both the direct and the depolarized backscattered signal. The system has been operational in northern Finland since the end of November 1991.     

Interaction of laser radiation with TNT with respect to the laser neutralisation of AP mines

According to UN estimations there are between 80 and 115 million activated landmines worldwide. These mines, or other unexploded ordnance (UXO), can be triggered accidentally and kill or injure more than 2000 civilians per month. The most common explosive in these mines is trinitrotoluene (TNT). In this paper, the potential of some of the most promising lasers for mine neutralisation is investigated, namely an ArF laser, a KrF excimer laser and a Nd:YAG solid-state laser. We have studied the interaction between laser beams emitting at λ=193 nm, 248 nm and 1060 nm and a bare solid sample of TNT of approximately 15 mg. Using pulsed excimer radiation at λ=193 nm, with an energy density up to 1 J/mm², ablation of the TNT without any deflagration has been achieved. At λ=248 nm, using the KrF excimer laser with a pulse duration of 30 ns and a repetition rate of 5 Hz, the TNT sample started melting and burning after an irradiation of 10 s. Preliminary results with the Nd:YAG solid-state laser operating in cw emission have shown that the irradiated sample exhibits the desired burning behaviour even after the exposure is stopped. Received: 14 December 2000 / Accepted: 18 December 2000 / Published online: 20 June 2001     

Tunable ultraviolet optical parametric oscillator for differential absorption lidar measurements of tropospheric ozone

A pulsed optical parametric oscillator (OPO) with intracavity sum frequency mixing was developed generating energies of up to 16 mJ in the 281–293 nm wavelength range. Both OPO process and sum frequency mixing are pumped by the harmonics of a single, medium-sized Nd:YAG laser. The system is characterized by a high overall efficiency (∼4% conversion from 1064 nm to the UV), a very compact set-up and stable and reliable operation. This system was successfully employed to measure tropospheric ozone using the differential absorption lidar (DIAL) technique and shows much promise as a lidar transmitter in airborne case studies as well as in unattended lidar systems for long-term monitoring. An unattended ozone profiling system could already be successfully realized. Received: 1 April 2002 / Revised version: 30 May 2002 / Published online: 2 September 2002 RID="*" ID="*"Corresponding author. Fax: +49-8153/28-1271, E-mail: Andreas.Fix@dlr.de     

Study of atmospheric water in gaseous and. liquid state by using combined elastic–Raman. depolarization lidar

A combined elastic–Raman lidar system based on a tripled Nd:YAG laser is used for the separate detection of elastic backscatter and Raman signals from atmospheric nitrogen, water vapor and liquid water and for their depolarization measurement. Vertical profiles of water-vapor and liquid-water content measured under clear-sky conditions behave differently: inside the boundary layer the ratio of liquid-water to water-vapor Raman backscatters rises with altitude. The depolarization measurements bring additional information about atmospheric scattering. The observed depolarization ratio of the water-vapor Raman signal is about 14%, while for liquid water this ratio varies in the 30–75% range, which exceeds the depolarization of bulk water and is attributed to the water-aerosol effects. Raman contours of water vapor and liquid water are partially overlapped, and bleed-through of liquid-water Raman backscatter leads to enhancement of depolarization of the water-vapor Raman signal. This parameter may be used as a convenient indicator of liquid-water interference in water-vapor measurements. Received: 12 December 2000 / Revised version: 27 September 2001 / Published online: 7 November 2001     

A new differential absorption lidar for NO_2 measurements using Raman-shifted technique

Based on Raman-shifted wavelengths of D2 and CH4 pumped by third harmonic of Nd:YAG laser, a differential absorption lidar was presented in this paper and had been constructed for probing environmental NO2 concentration. NO2 experimental measurements were carried out at Anhui Institute of Optics and Fine Mechanics in Hefei. Some NO2 measurement results were given and discussed.     

Optical and nonlinear optical characteristics of the Ge and GaAs nanoparticle suspensions prepared by laser ablation

The laser ablation of Ge and GaAs targets placed in water and ethanol was carried out using the fundamental radiation of nanosecond Nd:YLF laser. The results of preparation and the optical and nonlinear optical characterization of the Ge and GaAs nanoparticle suspensions are presented. The considerable shift of the band gap energy of the nanoparticles compared to the bulk semiconductors was observed. The distribution of nanoparticle sizes was estimated in the range of 1.5-10 nm on the basis of the TEM and spectral measurements. The nonlinear refractive indices and nonlinear absorption coefficients of Ge and GaAs nanoparticles were defined by the z-scan technique using second harmonic radiation of picosecond Nd:YAG laser (λ = 532 nm).     

Raman lidar for the study of liquid water and water vapor in the troposphere

A Raman lidar system based on a tripled Nd:YAG laser is used for profiling of water vapor and liquid water in the troposphere. The Raman signals from water in the gas and liquid state are separated by interference filters and their relative intensities are studied for different atmospheric conditions. For clean weather or immediately after the rain the Raman signal from liquid water inside PBL is about one order of magnitude lower than the signal from water vapor. But during cloud measurements both Raman signals become comparable and the results of water vapor measurements must be corrected for the interference of liquid water Raman scattering. The obtained results are used for the estimation of liquid water content in the atmosphere. Received: 4 October 1999 / Revised version: 18 February 2000 / Published online: 11 May 2000     

Finite element simulation of pulsed laser ablation of titanium carbide

In the present paper, a 2D finite element model based on the heat-conduction equation and on the Hertz-Knudsen equation for vaporization was developed and used to simulate the ablation of TiC by Nd:YAG and KrF pulsed laser radiation. The calculations were performed for fluences of 8 and 10 J/cm², which according to experimental results obtained previously, correspond to large increases of the ablation rate. The calculated maximum surface temperature of the target for both lasers is higher than the estimated value of TiC critical temperature, corroborating the hypothesis that the increase of the ablation rate is explained by the explosive boiling mechanism.     

基于Nd∶YAG/Cr∶YAG复合晶体的全固态紫外激光器

被动调Q产生1064 nm脉冲激光在腔外聚焦后入射到KTP中,产生532 nm的倍频光,再通过LBO和频产生355 nm激光。当抽运功率为3.4 W时,基频光调Q输出平均功率为350 mW,峰值功率达3.5 kW。腔外二倍频532 nm绿光输出平均功率为110 mW,用Ⅰ类相位匹配LBO晶体和频获得36 mW的355 nm的紫外激光输出,三倍频效率(1064~355 nm)达到10.2%。由于Cr∶YAG晶体达到饱和吸收后,会呈现出各向异性的特征,对基频光的偏振状态有很大影响。实验中必须合理放置复合晶体,使基频光的偏振状态为近似线偏振以提高转换效率。     

Demonstration of room-temperature laser action at 2.5 mum from Cr(2+):Cd(0.85)Mn(0.15)Te

Room-temperature laser action from Cr(2+)-doped Cd(0.85)Mn(0.15)Te has been demonstrated for what is believed to be the first time. We achieved pulsed laser operation centered at ~2.5mu m by pumping into the mid-infrared absorption band of Cr(2+) ions by use of the 1.907- mum output of a H(2) Raman-shifted Nd:YAG laser. The output of the free-running Cr(2+):Cd(0.85)Mn(0.15)Te laser had a width of ~50 nm (FWHM), and the slope efficiency was calculated to be 5.5% under nonoptimum conditions.     

BBO晶体的五倍频

本文报道了用BBO晶体对Nd:YAG激光器输出的1064nm光的五倍频,获得了213nm的紫外输出,266nm转换至213nm的转换效率达48%.并用数值积分的方法从理论上分析了1064nm与266nm的混频过程,得出的结论与实验结果相符.     

Short-pulse high-intensity excimer lasers — A powerful tool for the generation of coherent VUV and XUV radiation

Different approaches for the generation of coherent VUV and XUV radiation with a 400 fs KrF excimer-laser system are studied. In nonlinear optical experiments it is shown that four-wave difference-frequency mixing in Xe, using a near two-photon resonance with the KrF laser radiation, is well suited for the generation of tunable VUV radiation in the range 130–200 nm. Conversion efficiencies of 2% and output energies up to 260 J have been demonstrated. Further prospects to achieve J energies are discussed. Using this VUV source and the KrF laser, powerful XUV radiation can be generated by different low-order frequency mixing processes. In first experiments on this subject, direct frequency tripling of the KrF laser pulse has resulted in 14 J XUV radiation at 83 nm.For the realization of soft-X-ray lasers, specific advantages of short-pulse KrF drivers are discussed. Novel scenarios based on a hybrid KrF/Ti: sapphire laser system and multiphoton resonant excitation are considered.Prof. F. P. Schäfer on the occasion of his 65th birthday.     

Comparative study between IR and UV laser radiation applied to the removal of graffitis on urban buildings

The present article focuses on a comparison between cleaning process of graffitis on urban buildings by using laser radiation at 308 nm (XeCl excimer laser) and 1064 nm (Nd:YAG laser). Laser-induced breakdown spectroscopy (LIBS) elemental analysis was applied as real-time diagnostic technique, safeguarding against possible damage of the substrate during ablation rate studies. The morphological analysis of the etched surfaces by optical microscopy and environmental scanning electron microscopy reveals remarkable features of interest to understand the wavelength dependence of the ablation efficiency. The ablation threshold fluences of different paints sprayed on several substrates were determined applying a photoacoustic technique. To remove graffitis from urban buildings the laser radiation at 1064 nm was observed to be the most efficient wavelength, supporting the best result.     

Development of an optical parametric generator with pulsed dye amplification for high-resolution laser spectroscopy

An injection-seeded optical parametric generator (OPG), coupled with three pulsed dye amplification (PDA) stages, was shown to produce tunable, narrow linewidth laser radiation. The OPG was composed of a pair of beta barium borate (β-BBO) crystals and pumped by the third harmonic (355 nm) output of a seeded Nd:YAG laser. The OPG was injection-seeded at the idler wavelength (824 nm) using an external cavity diode laser (ECDL) with a mode-hop-free tuning range of 20 GHz. Using the PDA stages, the OPG output signal (624 nm) was amplified to 19 mJ/pulse, while maintaining a spectral linewidth of approximately 160 MHz at full-width-half-maximum (FWHM) which was within a factor of 2 of the Fourier limit. A system of lenses and apertures was used to minimize amplified spontaneous emission (ASE) in the PDA stages. Using the OPG/PDA system, two-photon laser-induced fluorescence measurements of atomic oxygen were performed by sum-frequency-mixing the 624-nm beam with the third harmonic output of the seeded Nd:YAG laser to generate approximately 1 mJ/pulse of ultraviolet radiation near 226 nm. Voigt line shapes were found to be in good agreement with oxygen atom spectra in atmospheric-pressure, laminar, counter-flow flames; the magnitude of Doppler and collisional broadening was approximately the same. The measured O-atom concentration profile was found to compare well with that calculated using an opposed-flow flame code.     

Blue luminescent silicon nanocrystals prepared by short pulsed laser ablation in liquid media

The pulsed laser processing in liquid media is an attractive alternative to produce room temperature luminescent silicon nanocrystals (Si-ncs). We report on a blue luminescent Si-ncs preparation by using nanosecond pulsed laser (Nd:YAG, KrF excimer) processing in transparent polymer and water. The Si-ncs fabrication is assured by ablation of crystalline silicon target immersed in liquids. During the processing and following aging in liquids, oxide based liquid media, induce shell formation around fresh nanocrystals that provides a natural and stable form of surface passivation. The stable room temperature blue-photoluminescent Si-ncs are prepared with maxima located around ∼440 nm with corresponding optical band gap around ∼2.8 eV (∼430 nm). Due to the reduction of surface defects, the Si-ncs preparation in water, leads to a narrowing of full-width-half-maxima of the photoluminescence spectra.     

Laser photolysis as applied to the determination of the two-photon absorption cross section of <Emphasis Type="Italic">trans</Emphasis>-stilbene

The two-photon absorption (TPA) cross section of an ethanol solution of trans-stilbene exposed to radiation of the second harmonic of a Nd:YAG laser (532 nm) of nanosecond duration has been determined using the method based on the measurement of the photodecomposition of trans-stilbene molecules, characterized by a low photostability. The measured TPA cross section of trans-stilbene in ethanol amounts to 25 ± 5 GM, and the photodecomposition quantum yield determined upon excitation by radiation of the fourth harmonic of the Nd:YAG laser (266 nm) is found to be γ = 0.10 ± 0.01. The obtained value of the TPA cross section has been compared with the experimental and theoretical data of other authors. The method of photodecomposition can be successfully used for the experimental determination of the TPA cross section of compounds unstable under the photoexcitation such as photochromic molecules, biological objects, and radical photoinitiators.     

Soot sublimation studies in a premixed flat flame using laser-induced incandescence (LII) and elastic light scattering (ELS)

Laser-induced incandescence (LII) as a diagnostic technique is based on rapid heating of soot particles to temperatures of several thousand Kelvin and subsequent detection of the thermal radiation from the laser-heated particles. At such high temperatures, soot sublimation effects must be considered when estimating uncertainties in LII measurements. In this work we have investigated the use of various laser fluences in LII using a Nd:YAG laser at 1,064 nm. Using another Nd:YAG laser at 532 nm, the elastic light scattering (ELS) signal from soot particles heated by the 1,064-nm laser was monitored. This approach makes it possible to determine at which fluence of the LII laser soot sublimation starts to become visible as a decrease in the ELS signal. By performing the measurements at various heights in a premixed sooting flat ethylene/air flame, the fluence threshold above which the ELS signal decreased was found to be higher at the lower flame heights corresponding to younger, smaller and less aggregated particles. The results from this work indicate that the different fluence thresholds for sublimation may be explained by a lower absorption function E(m) for the younger soot particles.     

Optical properties and highly efficient laser oscillation of Nd:YAG ceramics

Optical absorption, emission spectra have been measured for polycrystalline Nd-doped Y₃Al₅O₁₂ ceramics. Fluorescence lifetimes of 257.6 μs, 237.6 μs, 184.2 μs and 95.6 μs have been obtained for 0.6%, 1%, 2% and 4% neodymium-doped YAG ceramics, respectively. For the first time, highly efficient laser oscillation at 1064 nm has been obtained with this kind of ceramics. Slope efficiency of 53% has been achieved on a uncoated 4.8-mm thick 1% Nd:YAG ceramics sample. Optical to optical conversion efficiency is 47.6%. Laser oscillation has also been obtained with a 2% Nd:YAG ceramics. The optical properties and laser output results have been compared with that of Nd:YAG single crystal grown by the Czochralski method. Almost identical results have been achieved including laser experiments results. But fabrication of Nd:YAG ceramics is much easier compared to the single-crystal growth method. And also large size (now of about 400 mm diameter×5 mm is available) and high-concentration (>1%) Nd:YAG ceramics can be fabricated. The results show that this kind of Nd:YAG ceramics is a very good alternative to Nd:YAG single crystal. Received: 20 April 2000 / Published online: 16 August 2000     

Ti:sapphire laser intracavity difference-frequency generation of 30 mW cw radiation around 4.5 μm

A cw mid-IR coherent source based on difference-frequency generation is designed and characterized. For mid-IR generation, a periodically poled MgO:LiNbO(3) crystal is placed inside a compact Ti:sapphire laser cavity. This provides high-power pump radiation for the nonlinear process. Optical injection by an external-cavity diode laser ensures single-frequency operation of the Ti:sapphire laser, while signal radiation is provided by a fiber-amplified Nd:YAG laser. Mid-IR radiation can be generated with 3850-4540 nm tuning range, narrow linewidth, Cs-standard traceability, and TEM(00) spatial mode. 30 mW power is obtained at 4510 nm.