<Emphasis Type="Italic">Q</Emphasis>-Switched Yb-Doped Fiber Ring Laser with a Saturable Absorber Based on a Graphene Polyvinyl Alcohol Film

We propose, design, and demonstrate a Q-switched ytterbium-doped fiber laser (YDFL) employing a thin graphene polyvinyl alcohol (PVA) film as a passive saturable absorber (SA). The graphene is synthesized by electrochemical exfoliation of graphite at room temperature in 1% sodium dodecyl sulfate (SDS) aqueous solution. Graphene flakes obtained from the process are mixed with PVA solution as the host polymer to produce a thin film, which acts as a passive Q-switcher in the YDFL ring cavity. The laser generates a stable pulse operating at a wavelength of 1,076.4 nm with a threshold pump power of 73.7 mW. At a maximum 980 nm pump power of 113.6 mW, the YDFL generates an optical pulse train with a repetition rate of 25.53 kHz and a pulse width of 10 μs. The maximum pulse energy of 50.9 nJ is obtained at a pump power of 109.9 mW. A higher-performance Q-switched YDFL is expected to be achieved with optimization of the graphene saturable absorber and the laser cavity.     

A tunable multi-wavelength Brillouin–erbium fiber laser with fourfold Brillouin frequency spacing

We have experimentally demonstrated a tunable multi-wavelength Brillouin–erbium fiber laser with over 40 GHz spacing utilizing two cascaded double Brillouin-frequency-spacing cavities. In this laser configuration, two segments of 25 km-long single-mode fibers are used as Brillouin gain medium in each ring cavity, and a segment of 8 m-long erbium-doped fiber with 980 nm pump is employed to amplify Brillouin pump (BP). At BP wavelength of 1550 nm, BP power of 8.3 dBm (6.8 mW) and the maximum 980 nm pump power of 27.78 dBm (600 mW), seven output channels with fourfold Brillouin-frequency spacing, and the tuning range of 15 nm from 1545 to 1560 nm are achieved. The proposed multi-wavelength Brillouin–erbium fiber laser has wide applications, such as in microwave signal generation and optical communications.     

Generation of multi-wavelength square pulses in the dissipative soliton resonance regime by a Yb-doped fiber laser

Multi-wavelength square pulses are generated in the dissipative soliton resonance(DSR) regime by a Yb-doped fiber laser(YDFL) with a long cavity configuration. The spectral filter effect provided by a passive fiber with low-stress birefringence facilitates the establishment of multi-wavelength operation. Through appropriate control of the cavity parameters,a multi-wavelength DSR pulse can be generated in single-and dual-waveband regions. When the multi-wavelength DSR works in the 1038 nm waveband, the pulse duration can broaden from 2 ns to 37.7 ns. The maximum intra-cavity pulse energy is 152.7 nJ. When the DSR works in the 1038 nm and 1080 nm wavebands, the pulse duration can be tuned from2.3 ns to 10.5 ns with rising pump power. The emergence of the 1080 nm waveband is attributed to the stimulated Raman scattering(SRS) effect. Our work might help a deeper insight to be gained into DSR pulses in all-normal-dispersion YDFLs.     

Second Stokes 1129 nm generation in gray-trace resistance KTP intracavity driven by a diode-pumped Q-switched Nd:YVO4 laser

A gray-trace resistance KTP (GTR-KTP) second Stokes Raman laser intracavity driven by a diode-pumped acousto-optic Q-switched Nd:YVO₄ laser was first demonstrated in this paper. With an incident pump power of 9.5 W, the intracavity GTR-KTP Raman laser, operating at the repetition rate of 20 kHz, produced the maximum average output power of 860 mW at 1129 nm. The minimum pulse width obtained in this GTR-KTP Raman laser was 10.8 ns. When the GTR-KTP was substituted with a common KTP, a lower average output power of 720 mW and longer pulse width of 15.9 ns were obtained in the common KTP Raman laser under the same pump condition and cavity setup as the GTR-KTP Raman laser. Experimental results indicated that the decreased absorption at the fundamental and Stokes wave in GTR-KTP was beneficial to improve the stimulated Raman scattering performance.     

Room temperature,multi-wavelength operation in Er:YAG

Room temperature, multi-wavelength operation in 0.3% doped Er:YAG laser with double etalons pumped by a MgO:PPLN laser locked at 1532 nm was reported. Lasing occurred predominantly at 1645.1 nm and 1617.2 nm. 350 mW of 1645.1 nm, 160 mW of 1617.2 nm output were achieved under total incident pump power of 7 W.     

Influences of ASE on the performances of Q-switched ytterbium-doped fiber lasers

The output characteristics of actively Q-switched ytterbium-doped fiber lasers (YDFL) are investigated in this paper. Our experimental results show that, the combined effect between the short switching time and the gain transient property of doped fiber causes the initial amplified spontaneous emission (ASE) power fluctuation, forming the multi-peak structure in the output pulse for either ring or linear cavity Q-switched YDFL. The pulse buildup time decreases with the rising of the pump. Moreover, since the broad-band ASE generated in the YDF is very high, it may saturate the doped fiber once the switch has been opened, making it difficult to achieve Q-switched laser oscillation for both fiber lasers. By using ASE filter to suppress the initial ASE, the gain supplied by the YDF can be greatly enhanced, which can not only decrease the threshold, but also greatly decrease the duration, and enhance the peak power of the Q-switched laser pulse as well. By using such an ASE filter, the Q-switched laser pulse with the peak power of 40.7 W and the duration of 30 ns has been achieved for the linear cavity YDFL pumped with 160 mW.     

Graphene passively Q-switched Ho:YAG ceramic laser

We report on the first graphene passively Q-switched Ho:YAG ceramic laser with central wavelength of 2,097 nm. Stable pulses of 28–64 kHz repetition rate and 2.6–9 μs pulse widths were generated under 1,907 nm thulium fiber laser pumping. Maximum average power of 264 mW with 9.3 μJ pulse energy was obtained under 3.27 W of pump power.     

Passively Q-switched Tm,Ho:LuLiF4 laser with near constant pulse energy and duration

A compact diode-pumped passively Q-switched Tm,Ho:LuLiF₄ laser with a Cr:ZnS saturable absorber is demonstrated for the first time. The maximum average output power of 74 mW is achieved at the absorbed pump power of 1.5 W, and the threshold power is only 0.68 W. The laser operates at the wavelength of 2,055 nm and produces pulses with near constant duration of 1.2 μs and pulse energy of 13 μJ at the pulse repetition frequency from 1 to 5.2 kHz. The stable long-pulse laser can be used in laser lidar systems for accurate wind velocity measurements.     

Idler-resonant optical parametric oscillator based on KTiOAsO4

An idler-resonant KTiOAsO₄ (KTA) optical parametric oscillator is demonstrated within a diode-end-pumped acousto-optically Q-switched Nd:YAG laser. With an X-cut KTA crystal, idler wave at 3467 nm and signal wave at 1535 nm are generated. Under an incident diode pump power of 15.4 W, the idler output power of 105 mW and signal power of 720 mW are obtained at a pulse repetition rate of 40 kHz. The pulse widths of the idler and signal waves are 7.2 and 3.1 ns, respectively. The beam quality factors (M²) of the idler wave are within 1.2 in both horizontal and vertical directions.     

光纤激光泵浦MgO:PPLN高功率中波红外光参量振荡器

为实现高效率、高功率中波红外激光输出,研制基于MgO:PPLN晶体的中波红外光参量振荡器（OPO）,泵浦源为基于主振荡功率放大（MOPA）结构的线偏振掺Yb光纤激光器（YDFL）。实验结果表明:YDFL可实现最高79.1 W的1064.1 nm脉冲线偏振激光输出;在YDFL泵浦下,通过优化输出镜曲率半径和泵浦光束腰直径,该OPO实现最高9.15 W的3.754 μm脉冲激光输出,光光转换效率为11.57%,重复频率为300 kHz,脉冲宽度约为110 ns。     

Simultaneous intracavity optical parametric oscillation and stimulated Raman scattering pumped by a doubly passively Q-switched Nd:GGG laser

By using a doubly passively Q-switched Nd:Gd₃Ga₅O₁₂(Nd:GGG) laser with Cr⁴⁺:YAG and GaAs as saturable absorbers as pump laser, simultaneous intracavity optical parametric oscillation and stimulated Raman scattering based on a single X-cut KTiOPO₄ (KTP) crystal have been realized. Under an incident diode pump power of 10.5 W, the output powers at the signal wave near 1,569 nm and the first Stokes emission near 1,094 nm were 218 and 72 mW, corresponding to the optical-to-optical conversion efficiencies of 2.08 and 0.69 %, respectively. The measured shortest pulse duration at the signal wave near 1,569 nm was 580 ps, generating a pulse peak power of 43.7 kW, while the minimum pulse duration at the first Stokes emission near 1,094 nm was 1.61 ns. By adjusting the tilt angle of the KTP crystal, up to the third Stokes scattering was also obtained.     

Comparisons of multi-wavelength oscillations using Sagnac loop mirror and Mach-Zehnder interferometer for ytterbium doped fiber lasers

A multiwavelength Ytterbium-doped fiber ring laser operating at 1030 nm region is demonstrated using a Sagnac loop mirror and a Mach-Zehnder interferometer. We report the Performance comparisons of multi-wavelength oscillations in Yb³⁺ doped fiber lasers (YDFL) with typical commercial ytterbium doped silica fibers. By adjusting the polarization controller (PC), a widely tunable laser range of 22 nm from 1030 nm to 1050 nm is obtained. The Mach-Zehnder interferometer (MZI) design has exhibited simplicity in the operation for controlling the smallest wavelength spacing compared to Sagnac loop mirror method. In our observations, the smallest achieved stable wavelength spacing in Sagnac loop mirror setup and MZI setup were 2.1 nm and 0.7 nm, respectively. In case of nine-wavelength operation with a MZI setup, the stability, Full Width at Half Maximum (FWHM) and side mode suppression ratio (SMSR) of laser lines are not affected by increasing pump power, While for above four wavelength operation, the laser stability with Sagnac loop mirror becomes worse specially for higher input pump power and the power fluctuation among the wave-lengths would be also slightly larger.     

Graphene-based passively Q-switched Nd:KLu(WO4)2 eye-safe laser operating at 1,425 nm

With graphene as saturable absorber, an Nd:KLu(WO₄)₂ eye-safe laser operating at 1,425 nm is demonstrated. To the best of our knowledge, this is the first demonstration that an Nd:KLu(WO₄)₂ laser operates at the eye-safe 1.4-μm region. A maximum total average output power of 170 mW is obtained under the pump power of 9.6 W, corresponding to an optical–optical efficiency of 1.77 %. The minimum pulse width and the highest pulse repetition rate are 153 ns and 97 kHz, respectively. Also the characteristics of the graphene used as saturable absorber for a 1.4-μm laser were studied for the first time.     

Tunable passively Q-switched ytterbium-doped fiber laser using MoWS2/rGO nanocomposite saturable absorber

We demonstrated a tunable Q-switched ytterbium-doped fiber laser (YDFL) using MoWS₂/rGO nanocomposite as passive saturable absorber. Further, the Mo_1?xW_xS₂/rGO nanosheets, with x proportion of 0.2, are synthesized using hydrothermal exfoliation technique. The proposed nanocomposite-PVA based thin film is fabricated by mixing the MoWS₂/rGO nanosheets with polyvinyl alcohol (PVA). The fabricated thin film is sandwiched between two fiber ferrules to realize the proposed saturable absorber (SA). Further, the proposed MoWS₂/rGO-PVA based thin film SA exhibits a fast relaxation time and a high damage threshold which are suitable to realize a Q-switched pulsed laser with a tunable wavelength range of 10?nm that extends from 1028?nm to 1038?nm. For the highest pump power of 267.4?mW, the generated Q-switched pulses exhibit a narrow pulse width of 1.22 μs, the pulse repetition rate of 90.4?kHz, the highest pulse energy of 2.13?nJ and its corresponding average power of 0.193?mW. To the best of author’s knowledge, this is the first realization of a tunable Q-switching fiber laser in a 1?μm wavelength using MoWS₂/rGO nanocomposite saturable absorber.     

7-GHz high-repetition-rate mode-locked pulse generation using short-cavity phosphate glass fiber laser

A compact short-cavity high-repetition-frequency mode-locked fiber laser configured with Er³⁺/Yb³⁺ highly co-doped phosphate glass fiber and a graphene optical deposited film as saturable absorber is proposed and analyzed experimentally. The laser operates in stable mode-locked regime with fundamental repetition rate of 7.02 GHz. The output power is measured to be 1.2 mW with pump power around 80 mW, and the optical spectrum is centered about 1533.768 nm with mode spacing of 0.056 nm. As the pump power increases, the laser operates in multi-wavelength mode-locking emission state with the same longitude mode spacing. Moreover, the measure results show that different wavelength emission operates in different polarization states.     

Generation of multi-wavelength erbium-doped fiber laser by using MoSe_2 thin film as nonlinear medium and stabilizer

We experimentally demonstrate the application of MoSe2 thin film as a nonlinear medium and stabilizer to generate a multi-wavelength erbium-doped fiber laser. The cooperation of a photonic crystal fiber and a polari?zation-dependent isolator induces unstable multi-wavelength oscillations based on the nonlinear polarization rotation effect. A MoSe2 thin film is further incorporated into the cavity to achieve a stable multi-wavelength.The laser generates 7 lasings with a constant spacing of 0.47 nm at a pump power of 250 mW. The multi?wavelength erbium-doped fiber laser is stable with power fluctuations of less than 5 dB over 30 min.     

一种新型自激发布里渊掺铒光纤激光器

利用级联的受激布里渊效应,自激发布里渊掺铒光纤激光器可以实现常温下的多波长激光输出。通过在自激发掺铒光纤激光器中引入一个高双折射萨尼亚克(Sagnac)环形滤波器,调节萨尼亚克环形滤波器的偏振控制器(PC),实现了可调谐多波长输出,同时在实验中观测到双布里渊多波长带的现象。研究了这种光纤激光器中萨尼亚克环形滤波器的带宽和980 nm抽运光功率对输出波长数的影响,在萨尼亚克环形滤波器的带宽为83.3 nm以及980 nm抽运光功率为260 mW时,得到了52个间隔为0.088 nm的多波长激光输出。     

Tunable Q-switched ytterbium-doped fibre laser by using zinc oxide as saturable absorber

This paper demonstrates the use of a zinc oxide (ZnO) thin film in a 1-μm ring laser cavity as a saturable absorber to successfully generate Q-switching pulses. The tunability of the laser pulses is achieved by integrating a tunable bandpass filter (TBPF) in an ytterbium-doped laser cavity that results in 9.4 nm of tuning range, which wavelength is from 1040.70 nm to 1050.1 nm. The peak energy in the pulse which is 1.47 nJ was measured together with a minimum pulse width of 2.4 μs. In addition, the repetition rate increases from 25.77 to 45.94 kHz as the pump power level being increased from 103.1 to 175.1 mW. The results obtained in this experiment demonstrated consistent results and stable throughout the experiment. Therefore, ZnO thin film is considered as a good candidate in 1-μm pulsed laser applications.     

Theoretical and experimental investigations of nanosecond 177.3 nm deep-ultraviolet light by second harmonic generation in KBBF

We have presented theoretical and experimental investigations of nanosecond (ns) deep-ultraviolet (DUV) 177.3 nm radiation by means of second harmonic generation (SHG) from a frequency-tripled Nd:YAG laser (355 nm, 49 ns and 10 kHz) in KBe₂BO₃F₂ (KBBF) nonlinear crystal for the first time. A DUV KBBF-SHG numerical model, accounting for linear absorption, pump depletion, beam spatial birefringent walk-off and diffraction, is performed in the Gaussian approximation of spatial and temporal profiles. In the experiment, a maximum average output power of 14.1 mW at 177.3 nm was obtained. The dependence of 177.3 nm output power on the 355 nm pump power was simulated. The calculated results are in good agreement with the measured data. We used the model further to investigate the optical conversion efficiency, pulse width, beam spatial intensity profile and beam quality factor of the generated 177.3 nm light, in particular the effect of beam birefringent walk-off.     

Performance of 2 μm Tm:YAP pulse laser based on a carbon nanotube absorber

We demonstrated the first use of carbon nanotube as a saturable absorber in the Q-switched and Q-switched mode-locking of a diode pumped Tm:YAP operating at 2 μm. At the incident pump power of 8.64 W, the minimum Q-switched pulse width of 255.1 ns, and the maximum peak power 53.1 W can be obtained with the corresponding repetition rate of 21.76 kHz. The performance of a diode-pumped passively Q-switched mode-locked Tm:YAP laser with high repetition rate formed with a folded cavity. As high as 780 mW average output power was produced in QML laser. The repetition rate of the mode-locked pulse inside the Q-switched envelope was 244.1 MHz. The dependence of the operational parameters on the pump power was also investigated experimentally.