1 Gbit/s transmission over step-index plastic optical fiber using an optical receiver with an integrated equalizer

A single chip optical receiver with an integrated large-diameter photodiode, transimpedance amplifier, two stages active equalizer, post amplifier and 50 Ω driver is used for gigabit transmission over PMMA step plastic optical fiber (SI-POF). The large-diameter photodiode with an antireflection coating optimized for red light. The integrated equalizer enables the presented optical receiver to reach 1 Gbit/s over 50 m SI-POF at bit error ratio of 10^− 6. An error free (< 10^− 9) 1 Gbit/s data rate over 40 m standard PMMA step-index plastic optical fiber is also achieved.     

Giga-bit optical receiver for plastic optical fibre

An optical receiver with high sensitivity and linearity specially designed for Giga-bit communications over small-bandwidth high-attenuation multimode plastic optical fiber is presented. An automatic gain control transimpedance amplifier and linear post amplifiers are used to maintain a good performance with multilevel modulation. Using multilevel signaling and large-diameter integrated photodiodes make the presented optical receiver suitable for large core plastic optical fiber. For a wavelength of 675 nm, a sensitivity of −26.3 dB m (BER = 10⁻⁹) at 500 Mb/s is presented by a binary signal. A data rate of 1 Gb/s and a sensitivity of −19.8 dB m (BER = 10⁻⁹) are achieved with four-level pulse amplitude modulation.     

An optical receiver for eight-level data communication over step index plastic optical fiber

An optical receiver with automatic-gain-control transimpedance amplifier, linear post amplifier and linear line driver suitable for multilevel signals is presented. A large-diameter photodiode (400 μm) with an antireflection coating optimized for red light was integrated. These features enable the presented optical receiver to be a promising plastic optical fiber receiver. An error free (<10⁻⁸) 400 Mbit/s data rate over 50 m PMMA-step index plastic optical fiber (1 mm diameter) is achieved with eight-level pulse amplitude modulation (8-PAM).     

An 8 × 10 Gbps parallel single-chip light-to-logic converter

An 8 × 10 Gbps direct light-to-logic converter for hybrid mounted Ge photodiodes is presented. The receiver is realized in standard 0.35 μm SiGe BiCMOS technology and the Ge photodetector is directly mounted on the top of the CMOS wafer. Each of the 8 channels includes a transimpedance amplifier, limiting amplifier stages and a 50 Ω CML output driver. The overall transimpedance is 275 kΩ and at a data rate of 10 Gpbs a sensitivity of − 23.1 dBm (BER = 10⁻⁹) is reached.     

Polarization maintaining holey fibers for residual dispersion compensation over S + C + L wavelength bands

We report on a highly birefringent holey fiber for broadband dispersion compensation covering the S, C, and L telecommunication bands i.e. wavelength ranging from 1460 to 1625 nm. The finite element method with circular perfectly matched layer boundary condition is used to investigate the guiding properties. Numerical analysis demonstrates that it is possible to obtain negative dispersion coefficient of about −470 to −850 ps/nm/km over S to L-bands and a relative dispersion slope perfectly matched with single mode fiber (SMF) of about 0.0036 nm⁻¹ at 1550 nm. At the same time birefringence of the order 2.53 × 10⁻² is realized at 1550 nm wavelength. Owing to superior optical properties of the proposed holey fiber, this can be a promising candidate for broadband dispersion compensation and sensing applications.     

64 GHz optical millimeter-wave generation by octupling 8 GHz local oscillator via a nested LiNbO3 modulator

A novel scheme to generate a 64 GHz optical millimeter (mm)-wave via a nested LiNbO₃ Mach-Zehnder modulator with an 8 GHz local oscillator is proposed and simulated. Since the frequency response of the modulator and the local oscillator frequency are greatly reduced, the bandwidth requirements of the optical and electrical components in the transmitter are significantly decreased. The simulation results show that the generated optical mm-wave signal maintains good performance even after being transmitted over 20 km standard single-mode fiber.     

High-resolution spectroscopy using interleaved 100 GHz optical frequency comb scanned by phase modulator

A high-resolution spectroscopy technique is proposed with an optical phase modulator combined with an interleaved optical frequency comb. The optical phase modulator and a frequency-locked laser light guarantee a spectral resolution less than 1 MHz on an absolute frequency axis. A wide measurement frequency range was realized using a 25 GHz optical frequency comb lying over a 4 THz frequency region. An extraction of single tooth intensity from the comb was realized by a heterodyne technique with a frequency-tunable laser used as a local oscillator. Also, the 25 GHz optical frequency comb was interleaved to generate four 100-GHz combs for removing the crosstalk from the 25 GHz neighboring sidebands in the teeth. This proposed spectroscopy technique was experimentally demonstrated with a resonator of less than 1 MHz linewidth and a H¹³C¹⁴N gas cell. Thus, a measurement frequency range higher than 4 THz (1530 nm-1560 nm) was confirmed with an effective spectral resolution 100 kHz order. In addition, the characteristics of the proposed system were compared with those of the previous system with a single-sideband (SSB) optical modulator.     

Practical optical frequency measurement system around 1.5 μm based on an acetylene-stabilized laser-locked optical frequency comb

We have developed a practical and precise frequency measurement system at 1.5 μm telecommunication band. An electro-optic-modulator based optical frequency comb is phase-locked to a dither-free acetylene-stabilized laser to realize an optical frequency comb with frequency uncertainty of 10 kHz (5 × 10⁻¹¹) and the linewidth of 15 kHz. The present frequency comb can be also used as an optical frequency reference grid defined by ITU-T (International Telecommunication Union, Telecommunication Standardization Sector). Using the present frequency measurement system, we have demonstrated the first optical frequency measurement of ¹²C¹⁶O overtone absorption lines around 1.56 μm with the uncertainty of lower than 900 kHz.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Optimizing 10 Gbps optical communication system with duty cycle selection of return to zero pulse

We have investigated the return-to-zero (RZ) pulse duty cycle for single-channel Standard Single mode fiber (SSMF), Non Zero Dispersion shifted fibers (normal NZDSF and anomalous NZDSF fiber) for 10 Gbps optical fiber communication system. We give a comprehensive look on the behavior of variable duty cycle optical RZ pulse indicating that lowest bit error rate for duty cycle 0.8 among the duty cycle values 0.2, 0.4, 0.6 and 0.8 investigated for the case of SSMF. The single repeaterless mode fiber length is increased from existing 55 km at duty cycle 0.2 to fiber length 85 km by keeping duty cycle at 0.8. The result is also emphasized through the 10 dB Q value improvement and corresponding improvement in average eye opening diagram. The normal NZDSF show similar improvement but at greater fiber length, it offers BER 10⁻⁹ at length 110 km with duty cycle 0.2. NZDSF operating length can further be increased to length 160 km by keeping duty cycle 0.8. The corresponding 8 dB Q value improvement and Average eye opening improvement also supports the result through its graphical variation. Thirdly Anomalous NZDSF for same optical communication system showed that 0.2 duty cycle value give operational length of 130 km which could be extended to 160 km if 0.8 duty cycle is kept. The corresponding 8 dB Q value improvement, average eye-opening improvement endorsed the fact in the graphs.     

Ultra-fast 160:10 Gbit/s time demultiplexing by four wave mixing in 1 m-long B2O3-based fiber

One meter-long spool of bismuth oxide-based fiber, with nonlinear coefficient of 1250 W⁻¹ km⁻¹, is used to realize an optical 160-to-10 Gbit/s demultiplexer based on four wave mixing. Bit-Error-Rate measurements demonstrate a demultiplexing penalty lower than 2 dB confirming the suitability of bismuth oxide-based fiber for 160 Gbit/s all-optical processing.     

Enhanced performance for 10 Gb/s long reach RSOA based WDM-PON by using power pre-emphasized OFDM signal

An extended reach 10 Gb/s wavelength division multiplexing passive optical networks (WDM-PONs) system based on reflective semiconductor optical amplifier (RSOA) is proposed by using power pre-emphasized orthogonal frequency division multiplexing (OFDM) signal. Experimental results show that the proposed technique can effectively enhance the system performance against the limited bandwidth and chirp induced fading effect from direct modulation of RSOA. The receiver sensitivity is improved by 5 dB at the limit of BER for forward error correction (FEC) code over the 60 km and 85 km fiber transmission without any dispersion compensation module.     

100 Gb/s RZ-OOK transmission through 212 km deployed SSMF using monolithically integrated ETDM receiver module

100 Gb/s on-off keying (OOK) transmission over 212 km installed standard single-mode fibers using an Indium Phosphide (InP)-based electrical clock-data-recovery (CDR) and demultiplexer module was demonstrated. 5.5 × 10^− 11 bit error rate (BER) performance was achieved and 1.1-dB optical signal-to-noise ratio (OSNR) penalty was required at 10^− 9 BER after transmission.     

Performance enhanced down-stream signalling for next generation long-reach 10 Gbit/s passive optical networks

In this paper, we have analyzed the signal processing methods both in digital and optical domain to enhance the transmission performance of downstream signalling in long reach passive optical networks (LR-PONs). The impact of non-linear (NL) equalization through signal processing, i.e. Volterra Equalization (VE), Digital Backpropagation (BP) and Optical Phase Conjugation with Non-linearity Module (OPC-NM) is investigated, in 10 Gbit/s (XG) DP-QPSK long-reach wavelength division multiplexed (WDM) PONs without midspan repeaters over 120 km standard single mode fibre (SMF) link for down-stream signals. Due to the compensation of optical Kerr effects, the sensitivity penalty is reduced to 2 dB by BP algorithm, 1.5 dB by VE algorithm and 2.69 dB by OPC-NM. Moreover, with the implementation of NL equalization technique we are able to get the transmission distance of 126.6 km SMF for the 1:1024 split-ratio at 5 GHz channel spacing in the non-linear region. Furthermore, the concept of super passive optical network (S-PON) is also evaluated, which involves a repeater stage consisting of optical amplifiers, to study the feasibility for receiver side signal processing and simplification.     

Photonic generation of 60 GHz-band vector signals for RoF systems based on optical vector signal down-conversion

A novel photonic method of 60 GHz-band vector signal generation for RoF systems based on optical vector signal down-conversion is proposed and experimentally demonstrated in this paper. In the proposed method, the target vector signals are first generated in the optical domain with the help of mature commercial optical devices and then directly distributed to the base stations (BSs) through the fiber link. The generated vector signals can be automatically down-converted to the 60 GHz band in the BSs after O/E conversion, and then directly transmitted to the users without any further processing. With the proposed method, higher spectrum efficiency and system capacity will be obtained compared with the traditional OOK RoF systems while almost no extra system complexity and cost is brought in. According to the characteristics of different types of vector signals, two particular modulation schemes are provided, which are then verified by corresponding simulations and experiments. In the experimental 60 GHz RoF system, the 622 MSym/s 60 GHz-band 8-QAM and 4-QAM signals generated with two different schemes respectively are successfully transmitted over 50 km SMF and 5 m wireless channel without any compensation, and the power penalty are both about 1.7 dB at the BER of 10^− 9.     

Scanning tunneling microscopy luminescence from nanoscale surface of GaAs(1 1 0)

Scanning tunneling microscopy luminescence (STML) was induced from the nanometer scale surfaces of cleaved n-type and p-type GaAs(1 1 0) wafers by using of an ITO-coated optical fiber probe in an ultrahigh-vacuum chamber. The STML from n-type GaAs(1 1 0) surface was induced under negative sample bias when the applied bias exceeds a threshold voltage around −1.5 V. Whereas the STML from p-type GaAs(1 1 0) surface was induced under positive sample bias when the applied bias exceeds a threshold voltage around +1.5 V. The excitation energies at the threshold voltages are consistent with the band gap of GaAs (1.42 eV) at 295 K. The typical quantum efficiencies for n-type and p-type GaAs are about 3 × 10⁻⁵ and 2 × 10⁻⁴ photons/electron, respectively. The observed STML from are attributed to a radiative recombination of electron-hole pairs generated by a hole injection for n-type GaAs under negative sample bias and an electron injection for p-type GaAs under positive sample bias, respectively.     

10 Gb/s TDM passive optical networks using four wavelengths multiplexed channels

We propose a new architecture for 10 Gb/s upstream traffic in TDM-PON using externally injection-locked Fabry-Perot laser diodes (FP-LDs) in each optical network unit (ONU). Four directly modulated 2.5 Gb/s FP-LDs were injection-locked by continuous wave (CW) carriers distributed from the optical line terminal (OLT). Hence, a total of 10 Gb/s upstream traffic can be achieved. Experimental results show negligible power penalty at a transmission of 25 km standard single mode fiber (SMF) without dispersion compensation. The performance of the injection-locked FP-LD is also studied.     

High resolution analysis of the rotational levels of the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states of SO2

A high resolution (0.0018 cm⁻¹) Fourier transform instrument has been used to record the spectrum of an enriched ³⁴S (95.3%) sample of sulfur dioxide. A thorough analysis of the ν₂, 2ν₂ − ν₂, ν₁, ν₁ + ν₂ − ν₂, ν₃, ν₂ + ν₃ − ν₂, ν₁ + ν₂ and ν₂ + ν₃ bands has been carried out leading to a large set of assigned lines. From these lines ground state combination differences were obtained and fit together with the existing microwave, millimeter, and terahertz rotational lines. An improved set of ground state rotational constants were obtained. Next, the upper state rotational levels were fit. For the (0 1 0), (1 1 0) and (0 1 1) states, a simple Watson-type Hamiltonian sufficed. However, it was necessary to include explicitly interacting terms in the Hamiltonian matrix in order to fit the rotational levels of the (0 2 0), (1 0 0) and (1 0 1) states to within their experimental accuracy. More explicitly, it was necessary to use a ΔK = 2 term to model the Fermi interaction between the (0 2 0) and (1 0 0) levels and a ΔK = 3 term to model the Coriolis interaction between the (1 0 0) and (0 0 1) levels. Precise Hamiltonian constants were derived for the (0 0 0), (0 1 0), (1 0 0), (0 0 1), (0 2 0), (1 1 0) and (0 1 1) vibrational states.     

Study of all-fiber flat-top passband interleaver based on 2 × 2 and 3 × 3 fiber couplers

An all-fiber interleaver of cascaded Mach-Zehnder interferometer (CMZI) using a 2 × 2 and three 3 × 3 fiber couplers with almost rectangular wavelength response is developed by using a new configuration. Based on the digital approximation method of Fourier series, the relationships among the coupling ratios of the couplers, the length difference of interference arms and the intensity transmission spectrum are analyzed. The results indicate that a uniform flat-top spectral response can be obtained by the configuration when the length difference of interference arms and the coupling coefficient of the couplers, with some certain values, are given. The passband and stopband of optical interleaver are improved remarkably. Compared with conventional CMZI using 2 × 2 fiber couplers, the most advantage of the present method is that the coupling ratio of couplers can be controlled accurately because the interference effect of the monitor light can be sheered away in the course of fabricating couplers. A novel structure of filter is fabricated by using the fused biconical taper technics in experiment. The experiment results are in good agreement with the analytical ones.     

Reduction in timing jitter by chirp selection for externally modulated return to zero optical soliton pulse at 10 Gb/s

We investigate the chirp selection of externally modulated RZ soliton pulse at 10 Gb/s for fiber optical communication systems for the reduction in timing jitter. We have chosen single arm Mach-Zehnder amplitude modulator with sin² electrical shaped input-output (P-V) characteristic and its chirp range has been varied in the range of −5 to 5. The timing jitter, Q factor and bit error rate (BER) generated for the chirp range has been studied for various fiber lengths and post compensation has been demonstrated to reduce the timing jitter. The number of fixed output amplifiers after every 60 km span is varied from 2 to 10 and corresponding accumulated ASE noise has been studied to manage timing jitter and BER in permissible range, i.e. 5 ps and 10⁻⁹, respectively. It is observed that when two fiber spans are taken then the compensating fiber length for the system is less than 20 km for each case of the chirp considered. For 10 fiber spans, the compensating fiber length increases in the range 60-90 km depending upon the value of chirp taken. Finally it is shown that the chirp value of external modulator should be set to either 0 or −1 for externally modulated RZ soliton pulse in 10 Gb/s optical communication system which makes the system more insensitive to the timing jitter and the selection of dispersion compensating fiber length.