环状输出UR90束旋转非稳腔的实验研究

 提出一种适合于高功率超音速横流氧碘化学激光器的环状输出的UR90束转非稳腔,采用FFT 方法模拟了具有非均匀分布的小信号增益时最低阶模的光场强度分布。利用大口径铜蒸汽激光器, 通过实验研究了在放大倍率为1.21和1.13的情况下,环状输出UR90腔正向模与反向模的基本特性, 得到较好的实验结果。     

分布反馈光纤激光器弯曲特性的实验研究

为了研究分布反馈光纤激光器的弯曲特性,对光纤激光器输出波长和弯曲半径的关系进行了理论分析和实验研究.理论分析表明,光纤激光器输出波长变化量与弯曲半径平方的倒数为线性相关,并且随着弯曲半径的增大布拉格波长向短波长方向移动;实验中通过对3支不同波长的光纤激光器在弯曲半径分别为1O mm、20 mm、90 mm时输出波长的测...     

气体开关抖动对单模块快脉冲直线型变压器驱动源输出特性的影响

分析了快脉冲直线型变压器驱动源(FLTD)气体开关触发击穿延时的分布规律,利用MAT-LAB软件生成随机序列模拟开关击穿延时和抖动,在FLTD简化二阶电路的基础上,利用MATLAB分析了开关抖动对40个支路并联1 MA,100 ns FLTD模块输出电流脉冲前沿和幅值的影响。模拟计算结果表明:开关理想时,即抖动为0,输出电流峰值为996 kA,峰值时间为90 ns,10%~90%脉冲前沿为54 ns;开关自身抖动与开关之间分散性之和为10 ns时,输出电流脉冲前沿增加约14%,电流峰值下降约2%;开关自身抖动与开关之间分散性之和为20 ns时,输出电流脉冲前沿增加约38%,电流峰值下降约5%。     

激光窗口形状对应力和光束位相影响的数值计算

 计算对流冷却下500kW DF激光器CaF₂输出窗口的温升,得到了平板形和球壳形输出窗口的应力分布和光束的位相分布;分析了窗口形状对应力和位相分布的影响。     

X波段极化可重构高功率微波辐射器仿真设计

为了提高高频段高功率微波反射面天线的馈电效率,同时使波束波导馈线更加紧凑,提出一种新型的X波段极化可重构高功率微波辐射器结构。通过波纹喇叭辐射器产生准高斯的HE11模辐射,采用双相位修正镜组成的波束变换系统实现将准高斯波束转换为电场分布更为均匀的平顶波束或其余期望分布的波束,平顶分布的输出波束可使得馈源在相同介质窗尺寸下获得更高的功率容量,同时实现了波束传播方向的90°转弯;此外采用双圆极化栅网的级联组合,实现了对输出波束极化特性的调变。通过全电磁波仿真分析验证了该辐射器的设计思路。     

二极管面阵侧泵浦Nd:YAG双板条激光器

 叙述了二极管面阵侧泵浦双板条耦合单横模 Q 开关激光器的研制。泵浦源为二极管面阵激光器,使用梯形波导板耦合系统,耦合效率达90%,谐振腔为凸凹腔,全反射镜的曲率半径为 3.0m的凹面镜,输出镜为曲率半径3.0m的可变反射率超高斯镜。激光器在 100Hz 重复频率下,输出单脉冲能量18.23mJ,脉宽为15.25ns,光束质量M²<1.5具有平顶分布的超高斯光束。     

氧碘化学激光器束转动90度环形非稳腔空心光束输出研究

 主要描述了氧碘化学激光器束转动90°环形非稳腔（UR90）空心光束输出的腔结构及几何模式特点,实验中获得了在放大率M=1.695,激光平均输出功率4.0kW时,空心光束输出的激光光束质量为3.2倍衍射极限,同时对空心光束输出特性进行了分析。     

径向线型模式变换器

 研究了一种通过改变波导内场分布的旋转对称性,可将高功率微波源输出的TEM模或TM01模转换为TE11模的径向线型模式变换器。介绍了该模式变换器的基本原理,即采用金属插板将同轴波导TEM模变换为4路90°扇形波导TE11模,各路扇形波导间所需的输出相位差通过将扇形波导转换为双层径向线传输来实现。基于这一原理,设计了一个中心频率为1.6 GHz的同轴TEM-TE11模式变换器,并进行了数值模拟计算,结果表明该模式变换器具有较高的功率容量,中心频率处反射系数为0.05,模式转换效率为99%,在1.52~1.68 GHz的频带范围内,模式转换效率大于90%。     

角锥棱镜谐振腔激光模式模拟研究

为了探究角锥棱镜谐振腔激光模式,以角锥-平面镜腔为例,将角锥棱镜等效为衍射光栅,考虑角锥镜棱宽在谐振腔中的衍射效应以及二面角误差引起的附加相位分布对谐振腔激光模式的影响,在光学谐振腔理论的基础上,建立了求解本征模式的理论分析模型.采用快速傅里叶法数值模拟不同腔长、角锥镜棱宽和二面角误差情况下该无源谐振腔激光输出模式分布情况.结果表明,在腔长30 cm、角锥镜棱宽小于75μm、二面角误差在-10′~5′之间时,可实现光斑完整的圆形分布输出模式,且有较好的光束质量;棱宽不小于0.4 mm,二面角误差在-40′~10′之间时,光斑为TEM 03阶横模,光场呈六瓣分布;当角锥镜棱宽为0.4 mm、二面角误差为3′,腔长从30~90 cm范围内增加时,该谐振腔输出的激光模式从TEM 03转换成TEM 10.     

增压输送过程中卧式贮罐液氢温度分层研究

分析了大型卧式液氢贮罐增压输出过程中低温介质传热数学模型,揭示了贮罐内液氢温度分布规律,说明了液氢温度分层形成的原因及过程,给出了输出液氢品质保障方法。研究表明:大型卧式液氢贮罐输出过程中液氢温度分布可用修正后的半无限大平板非稳态导热方程描述;在增压压力一定情况下,热液层厚度随着输送时间的增加而增大,且热液层厚度及其温度分布受卧式贮罐截面形状影响;液氢贮罐输出品质与贮罐内热液层厚度密切相关,可通过计算热液层厚度从而确定贮罐留底余量的方法,保证贮罐输出品质。     

A novel automatic measurement method of laser beam divergence angle based on two linear array charge coupled devices

We propose a scanning imaging measurement method using two linear array charge coupled devices (CCD) to evaluate the transmission performance of the linear laser beam of 90° × 2°. The two linear array CCDs are placed at two positions in the far field separated by a definite angle. The beam divergence angles in the view direction are measured by linear fitting because the beam width conforms to the linear relationship in the far field. This method has the ability for real-time testing and is appropriate for the complicated beam shapes with a wide measurement range.     

High electro-to-optical efficiency 180 W Q-switched 532 nm laser with a pulsewidth of 70 ns

A compact straight cavity with two side-pumped Nd:YAG laser heads and a 90° quartz rotator in between is presented. By intracavity-frequency-doubling with a type II LBO crystal in this cavity, an output power of 180.2 W at 532 nm with a repetition rate of 10 kHz was achieved, corresponding to an electrical-to-optical efficiency of 10.9%. To best of our knowledge, this is the highest electrical-to-optical efficiency of the high power green lasers with above 100 W output power, ever reported. The pulsewidth was 70 ns and the peak power was 257.4 kW. The beam parameter product (beam waist multiplied by half beam divergence angle) was estimated to be 4.2 mm mrad and the power fluctuation over 2.5 hours was calculated to be better than ±1.2%.     

Spatial beam profiles of femtosecond X-ray pulses generated by laser Compton scattering from a low-emittance electron beam

Polarization-dependent spatial beam profiles of femtosecond X-ray pulses generated by a laser Compton scheme were measured. The X-ray pulses were generated by the interaction at an angle of 90° between 100-fs laser light and a 3-ps, 3π-mm mrad electron beam. The polarization of the laser light was linear in two different directions, either parallel or perpendicular to the electron beam axis. The measured profiles showed good agreement with theoretical results. Received: 5 July 2002 / Revised version: 17 October 2002 / Published online: 5 February 2003 RID="*" ID="*"Corresponding author. Fax: +81-424/684477, E-mail: msf_yorozu@shi.co.jp     

LBO晶体和频产生589 nm激光的数值模拟及实验研究

 基于非线性光学理论，分析了1 064 nm和1 319 nm和频产生589 nm激光源的理论基础。针对LBO晶体的I类相位匹配条件及最佳晶体长度的选择进行了计算机数值模拟，给出了最佳晶体长度与总入射功率的关系曲线。当波矢量与光轴夹角为90°，波矢量方位角为3.39°时，计算出相应的有效和频系数为0.952×10^-12 m/V。设计了一种简便高效的实验和频方案，二极管泵浦Nd:YAG激光器经腔镜镀膜及腔内可倾斜标准具调谐，分别输出了波长为1 064 nm和1 319 nm的准连续激光，然后通过脉冲同步调节，实现了589 nm黄光输出，平均功率达到500 mW，光束质量因子M2约2.1，和频效率18%。     

Fluctuation of femtosecond X-ray pulses generated by a laser-Compton scheme

A short-pulse X-ray-generation experiment was performed by Compton scattering through interaction between a 3-ps electron beam and 100-fs laser photons in a 90° scattering configuration. The observed X-ray intensity was typically 3×10⁴ photons/pulse and roughly matched the theoretically expected intensity. The X-ray energy and pulse duration were estimated theoretically to be 2.3 keV and 280 fs from the observed electron- and laser-beam parameters. The fluctuation of the X-ray output was measured as 25% (rms) during a 30-min operation. The fluctuation was expressed as a function of the fluctuation of the timing between the electron and laser beams. The measured fluctuation of the X-rays was approximately consistent with that caused by the fluctuation of the timing between the beams. Received: 19 November 2001 / Revised version: 23 January 2002 / Published online: 14 March 2002     

The continuous energy dependence of pp differential elastic cross sections between 500 and 1200 MeV

Using an internal jet target in the Saturne synchrotron, we have measured the proton-proton differential elastic cross section at 90° c.m. as a continuous function of energy (from 500 to 1200 MeV) during the acceleration of the beam. The energy resolution is about 2 MeV. The results are compared to predictions of phase-shift analyses and discussed in connection with amplitude analyses at 90° c.m. No resonant structure was observed and no evidence for narrow dibaryons was found.     

Periodic arrays of submicron Si and Ni dots on SiO2 fabricated using linearly polarized Nd:YAG pulsed laser

Periodic arrays of submicron Si and Ni dots were fabricated by only irradiating a linearly polarized Nd:YAG pulsed laser beam to Si and Ni thin films deposited on silicon dioxide (SiO₂) film. The interference between an incident beam and a scattered surface wave leads to the spatial periodicity of beam energy density distribution on the surface of the irradiated samples. A thin film was melted using a laser beam, and the molten film was split and condensed owing to its surface tensile according to the periodic energy density distribution. Then, the fine lines (line and space structure) were formed periodically. After the formation of fine lines, the sample was rotated by 90°, and the laser beam was irradiated. The periodic energy density distribution was generated on the fine lines, and the lines were split and condensed. Eventually, the periodically aligned submicron dots were fabricated on the SiO₂ film. PACS 79.20.Ds; 42.62.-b; 81.40.-z     

国产有源光纤成功实现6 kW激光输出

光纤激光是继气体激光、化学激光和固体激光之后的新一代激光技术,是近年来世界各国科学研究的热点领域。制约光纤激光功率提升的主要技术瓶颈是系统集成技术和光纤材料制备技术。目前,我国科研工作者成功掌握了千瓦级光纤激光系统集成技术并实现了产业化,但是所用的光纤激光材料与核心器件还严重依赖进口。相较于比较成熟的系统集成技术,我国光纤激光材料的科学研究和产业化进程相对滞后,尚无法提供成熟稳定的有源光纤产品。 2016年6月,中国工程物理研究院激光聚变研究中心的研究人员经过近三年科研攻关,成功研发了30/900规格（纤芯30 m/包层900 m）镱掺杂铝磷硅（Yb-APS）三元体系激光光纤并实现了6.03 kW最高功率输出,在5 kW功率水平下可长期稳定工作。光纤激光材料综合测试平台采用了传统的1+1型MOPA放大结构（即信号种子源与一级主放）:信号光种子源的功率为40 W,光束质量M2=1.1;第二级MOPA放大级使用的976 nm LD泵浦光总功率9.95 kW,经过CPS功率剥离器激光净化处理后,最终安全地实现了6.03 kW最大功率输出。如图1所示,最高输出功率时斜率效率为61.25%,源于1∶30的芯包比和20 m以上的光纤使用长度;激光输出光谱中心波长1080 nm,3 dB带宽为1.89 nm,受激拉曼抑制比＞15 dB;5 kW稳定工作时,光束质量M2=2.38,未发现光子暗化效应。中物院激光聚变研究中心所研制的镱掺杂铝磷硅三元体系有源光纤(30/900 Yb-APS fiber)成功实现了6.03 kW激光输出,是我国高功率光纤激光材料研究领域的重要进步,为制备低损耗、高掺杂、高吸收、高增益、无光子暗化效应的商业激光光纤产品奠定了坚实的技术基础。     

How to flip the polarization of infrared laser beams

We report on a seven-mirror device usable for flipping the linear polarization of a laser beam by 90°. It works over a broad spectral range in the infrared and can withstand high power. Also, flipping by angles other than 90° is possible at the expense of introducing small elliptical polarization.     

Development of copper bromide laser master oscillator power amplifier system

Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function of operating parameters. The electrical input power was varied from 2.6 to 4.3 kW, the pulse repetition frequency (PRF) was changed from 16 to 19 kHz, and the pressure of the buffer gas (neon) was kept fixed at 20 mbar. When the electrical input power was increased to 4.3 kW from 2.6 kW, the tube-wall temperature also increased to 488°C from 426°C but the ratio of the green to yellow power decreased to 1.53 from 3.73. The ratio of green to yellow power decreased to 1.53 from 1.63 when the PRF of the laser was increased to 19 kHz from 16 kHz. These observations are explained in terms of electron temperature, energy levels of transitions, and voltage and current waveforms across the laser head.