介质密度对谐振腔声压的影响

基于热声效应的磁致伸缩换能器热声制冷机,其内部的介质密度对于制冷效率的提高有重要作用。选用改变基础声压来控制谐振腔内介质密度的大小,选取了基础声压0.2—1.0 MPa之间,每0.2 MPa作为间隔,对五种基础声压下1 000—8 000 Hz不同激励下用有限元仿真软件ATILA进行仿真分析,得到趋势是呈现增大的,而且最大值在基础声压和激励频率最大值处,达到了359.97 Pa;在基础压力为0.6 MPa、激励频率为2 000 Hz的条件下谐振腔同时满足驻波形态和高声压。并对整机的模型进行激励频率-辐射板位移输出分析,得到在激励频率为9 000 Hz时,辐射板输出位移最大。随着介质密度的增加,热声制冷机内谐振腔内的驻波形态并没有因此而增加,存在一个同时满足驻波状态和高声压的状态。     

磁致伸缩-压电联合激励凹筒型发射换能器

设计制作了一种新型磁致伸缩-压电联合激励凹筒型发射换能器,采用稀土超磁致伸缩材料Terfenol-D与PZT压电陶瓷作为联合激励元件,模拟计算与实测结果均表明,与采用单一振子激励的凹筒型发射换能器相比,此种新型换能器在保持尺寸小、频率低等优点的同时,显著拓宽了工作频带并提高了辐射声功率.换能器外型尺寸为φ88 mm×316 mm,水中谐振频率1.30 kHz,-3 dB带通Q值1.43,谐振频率下发射电压响应级135.1 dB.     

磁致伸缩-压电联合激励凹简型发射换能器

设计制作了一种新型磁致伸缩-压电联合激励凹简型发射换能器,采用稀土超磁致伸缩材料Terfenol-D与PZT压电陶瓷作为联合激励元件,模拟计算与实测结果均表明,与采用单一振子激励的凹筒型发射换能器相比,此种新型换能器在保持尺寸小、频率低等优点的同时,显著拓宽了工作频带并提高了辐射声功率。换能器外型尺寸为φ88 mm×316 mm,水中谐振频率1．30 kHz,-3 dB带通Q值1．43,谐振频率下发射电压响应级135．1 dB。     

声悬浮实验中谐振腔形状对声压大小的影响研究

研究了不同谐振腔接收器表面的声压大小,发现谐振腔内增减凹球面反射面对声压波形有较大影响.分析了声压波形发生变化的原因,认为增加凹球面反射面时,声压波形变化是由于声波在谐振腔上下两表面存在非垂直反射.     

铁镓驱动弯曲圆盘换能器设计及振动特性研究

为了研究新型磁致伸缩材料——铁镓合金(Galfenol)在换能器中应用,本文设计了一种低频弯曲圆盘换能器。借助有限元软件仿真分析换能器振动模态,对换能器结构参数进行优化设计,并研制了换能器样品。利用激光测振仪测量了换能器空气中模态及不同电流驱动下振动位移,测得振动模态与仿真结果吻合,换能器空气中共振频率为913 Hz,辐射头能够产生的最大振动位移达到93μm,磁致伸缩材料达到饱和应变。结果表明:铁镓材料能够驱动弯曲圆盘换能器大振幅振动;铁镓作为磁致伸缩换能器驱动材料具有较好的应用前景。     

一种辐射声场近似计算方法——单元辐射叠加法

提出一种基于表面振速预报辐射声场的近似方法--单元辐射叠加法.研究表明,声传递向量中的每项元素等于对应单元以单位速度振动、其它单元振速都为零时的辐射声压,即刚性障板上活塞面以单位速度振动时的辐射声压.在此基础上,利用刚性障板上单位速度振动活塞面的辐射声压直接建立表面振速与辐射声压之间的传递关系,根据这个传递关系对表面振速进行加权、求和便得到总的辐射声压.计算时采用规则形状障板面去拟合实际障板面,以规则形状障板上振动活塞面的辐射声压去近似实际障板上振动活塞面的辐射声压.相对于边界元方法,该方法在计算速度与存储空间上具有很大的优势.计算表明该近似方法是合理的、可行的.     

纵振合成超声振动系统的研究

本文研究由磁致伸缩换能器驱动的纵向振动合成超声振动系统。文中介绍了结构设计,研究了声波导横向尺寸、驱动换能器数量及安装位置以及输入电功率对合成振动系统输出端位移振幅的影响,给出实验结果。由4个换能器组成的合成振动系统,当输入电功率为2.2KW时,在直径为20mm的输出端得到近300μm的双振幅。用于冷拔精密高压油管,产品精度达到西德DIN 7300A级国际水平。     

振动声成像系统分辨率研究

本文从振动声成像的基本原理出发，通过引入点扩展函数PSF和定义轴向响应函数ARF，研究了由凹球面聚焦换能器分割而成的一种典型共焦换能器参数对振动声成像系统侧向分辨率和轴向分辨率的影响。计算研究表明：增大凹球面换能器的口径、减小几何焦距和提高中心频率均可以提高系统的侧向分辨率和轴向分辨率；但改变凹球面换能器的分割比例对两种分辨率影响不尽相同。综合考虑超声换能器激励、聚焦性能以及产生的辐射力效果等因素，则换能器应按等辐射面积原则分割为宜。文中还分析了介质的声衰减系数对实际轴向分辨率的影响。     

磁致伸缩超声换能器阻抗匹配网络的设计*

根据磁致伸缩超声换能器的等效电路模型和阻抗匹配理论,该文设计了一种优化的型匹配网络。该网络具有调谐、变阻和滤波的功能,适用于工作在中低频超声频率范围内的磁致伸缩超声换能器系统的阻抗匹配。仿真和实验结果表明:接入该型阻抗匹配网络后,驱动电源与换能器之间实现了最大功率传输,换能器两端电信号的波形质量得到优化,换能器激励电流提升了40%。该研究可为大功率磁致伸缩超声换能器的应用提供技术支持。     

磁致伸缩-压电混合激励Janus换能器结构特征参量与纵振频率之间的关系

为了拓宽Janus换能器的工作频带,使用超磁致伸缩材料Terfenol-D与PZT压电陶瓷作为混合激励元件驱动Janus换能器,研究了其结构特征参量与纵振频率之间的关系.首先归纳了磁致伸缩-压电混合激励Janus换能器的12个结构特征参量.随后通过模态分析,证明换能器具有两种纵振动模态.最终经过有限元仿真计算,总结分析...     

Bistability of a compliant cavity induced by acoustic radiation pressure

We report on the first observation of multiple-order bistability due to acoustic radiation pressure in a compliant acoustic cavity formed between a spherical ultrasonic transducer immersed in water and the free liquid surface located at its focus. The hysteretic behavior of the cavity length, observed both with amplitude ramps and frequency sweeps, is accurately described using a one-dimensional model of a compliant Fabry-Pérot resonator assuming the acoustic radiation pressure to be the only coupling between the cavity and the acoustic field.     

Outer cavity Janus-Helmholtz underwater acoustic transducer

The outer cavity Janus-Helmholtz with sound insulation layer is presented for obtaining the capacity of high-power non-directional transmitting. The radiation efficiency and directivity in the 0 degrees direction can be improved when the radiation mode is changed by laying sound insulation layer. The operating bandwidth can be expanded effectively by the dual mode coupling between the cavity vibration and longitudinal vibration of Janus transducer. A prototype is designed by finite element method. Test results show that the results are in good agreement with the design results. Compared with inner cavity Janus-Helmholtz transducer,acoustic radiation performance of outer cavity Janus-Helmholtz underwater acoustic transducer in the 0 degrees direction has been significantly improved.     

Reduction of radiated exterior noise from the flexible vibrating plate of a rectangular enclosure using multi-channel active control

This study attempted to control the radiated exterior noise from a rectangular enclosure in which an internal plate vibrates by acoustic excitation and noise is thus radiated from that plate. Multi-channel active control was applied to reduce the vibration and external radiation of this enclosed plate. A piezoelectric ceramic was used as a distributed actuator for multiple mode control of the vibration and radiated noise in the acoustically excited plate. To maximize the effective control, an approach was proposed for attachment the piezoelectric actuator in the optimal location. The plate and internal acoustic space in the enclosure are coupled with each other. This will change dominant frequency characteristics of the plate and, thus, those of the externally radiated noise. Active noise control was accomplished using an accelerometer attached to the plate and a microphone placed adjacent to that plate as an error sensor under acoustic excitation of sine wave and white noise. It was found that the control of radiated external radiation noise requires a microphone as an error sensor, a sound pressure sensor due to vibration of the plate, differences in the dominant frequency of externally radiated noise, and complex vibration modes of the plate.     

外液腔式Janus-Helmholtz水声换能器

为获得具有大功率无指向性发射特性的水声换能器,提出了一种外液腔式Janus-Helmholtz结构。通过设置隔声层改变换能器的声辐射模式,从而改善声辐射效率和无指向性方向的声辐射能力,并利用外液腔振动和Janus换能器纵向振动耦合实现宽带发射。基于有限元法设计了一只工作频段为1.1~3.5 kHz的外液腔式Janus-Helmholtz换能器试验样机。样机测试结果显示与设计结果符合得较好,与内液腔式相比,外液腔式Janus-Helmholtz水声换能器在0°方向的声辐射能力得到了显著改善。      

压电瞬态响应在换能器声功率测量中的应用

探索一种简便的聚焦超声功率测量方法,利用压电陶瓷片直接接收超声信号,通过机电类比得到压电瞬态响应由压电片在声波作用力下引起受迫振动产生的电压响应与固有振动产生的高频衰减响应叠加而成,分析输出压电信号与换能器声功率之间的换算关系。对输出压电信号进行二次包络提取,获得表征声功率变化的电压幅度曲线,分别找出不同换能器驱动电压下包络曲线的最大峰值电压,将其平方值与声功率计所测声功率进行线性拟合,并对理论关系式中的比例系数进行标定。实验结果所得线性拟合度较高,且标定后所得声功率与声功率计所测值相对误差低于8.7%,证明了通过压电瞬态响应测量换能器声功率具有可行性。      

压电陶瓷非线性对大功率换能器结构参数匹配 影响的计算分析

在Guyomar非线性模型基础上,通过机电等效法将晶堆前向负载作为等效质量和阻尼加入振动方程的质量项和阻尼项,推导了换能器振速、辐射声压级和谐振频率偏移率等表达式,计算分析了压电陶瓷非线性参数和结构参数对换能器声辐射性能的影响,研究了压电陶瓷的非线性对换能器结构参数匹配的影响。结果表明,换能器节面靠前,前盖板厚度越小,前盖板大径越小,都可以减少压电陶瓷非线性引起的换能器频率偏移。当设计频率确定时,压电陶瓷处于非线性工作域的换能器的结构参数有所减小。换能器加入辐射端匹配后,可以改善压电晶堆前向负载匹配,降低换能器的谐振频率偏移率。换能器激励电流也会出现频率偏移现象。在提高换能器激励电压时,换能器的结构参数应适当减小。得到的结论可为换能器设计提供理论依据和帮助。     

球壳换能器电声效率测量方法及声场特性分析

在高强度聚焦超声治疗系统中,换能器的电声效率是治疗剂量控制中的重要参数,其在焦域附近的声场分布同样重要。该研究以球壳聚焦换能器为研究对象,基于辐射力天平法与平面扫描法进行输出声功率的测量,同时测量其激励电功率后计算得到电声效率,并就其声场特性分布以及存在的非线性传播现象进行了简单阐述。两种测量方法测得的电声效率在声学计量的误差允许范围内,实验结果表明两种方法在测量球壳聚焦换能器输出声功率时具备较好的一致性。     

板厚对无障薄板声辐射特性影响的分析

分析无障薄板的声辐射特性时通常忽略板厚对格林函数的影响而采用双层势计算.本文考虑板厚引起的声辐射阻抗,采用混合势计算结构表面声压与振速,并分析板厚对声辐射参数的影响。根据交界相容性条件,采用边界积分方程分别表示平板上下表面的声压和振速,并合并同类项.进一步将结构的动力方程代入混合势形式的振速方程中,离散声压差值和板的位移为振动模态叠加的形式,获得二重积分形式的声辐射阻抗,从而求解振动模态系数,确定声辐射特性参数.以水下简支矩形板为例计算对比了声辐射参数,并讨论了其对板厚的敏感性。结果表明:板厚引起的声辐射阻抗对声辐射参数的大小影响较小,但随着频率的增加致使共振频率发生较大偏移;在相同阶数的共振频率范围内,板厚度越大,采用双层势计算的误差越大。      

A Helmholtz resonator buried in the ground as a source of seismic waves and low-frequency sound in the atmosphere

The procedure is given for calculating the total power of low-frequency sound and seismic waves produced by a Helmholtz resonator in the form of an air-filled spherical cavity buried in the ground and supplied with a hole through which it is connected with the atmosphere. The sound is generated by air oscillations in the resonator’s neck section that is open to the atmosphere, while the compression and shear elastic waves are generated in the bulk of the ground by cyclic pressure fluctuations that act on the spherical walls of the cavity. Calculations show that the coincidence of the resonance frequencies (within approximately ten to hundred hertz), at which both the sound radiation to the atmosphere and the elastic seismic radiation in the form of longitudinal and transverse bulk waves are maximum, can occur only when the resonator is placed in a loose ground characterized by reduced elastic characteristics. In these conditions, the power of transverse waves exceeds the sound power by a factor of two and the power of longitudinal waves is smaller than the sound power by a factor of several tens.     

Study of ferrobielastic twinning in quartz under conditions of uniaxial pressure by the compound acoustic resonator method

The compound acoustic resonator method is used to study the phenomenon of the ferrobielastic transition in single crystals of quartz subjected to uniaxial pressure. Toward this end, a layered structure consisting of an aluminum film/zinc oxide film/aluminum film sandwich was deposited on one of the surfaces of an X-cut plane-parallel quartz plate. This structure served as an electromechanical transducer in such a way that the entire system acted as a multifrequency acoustic resonator. Uniaxial pressure was applied perpendicular to the direction of propagation of the acoustic waves and caused a growth of the frequencies of the resonance peaks of the structures, indicating a change in the velocity of the acoustic waves. The ferrobielastic phase transition, which arises at some threshold pressure (the ferrobielastic switching effect), is characterized by a discontinuous drop in the frequencies of the resonance peaks. The variation of the resonator frequency both below and above the switching threshold correlates with the variation of the so-called “natural” sound velocity determined by the pressure-dependent elasticity constants of the material. The observed frequency jump of the resonance peaks is due mainly to the relatively abrupt change in the dimensions of the crystal. The results of the acoustic measurements allow reliable recording of the switching effect and a study of its properties. Fiz. Tverd. Tela (St. Petersburg) 39, 290–294 (February 1997)