Theoretical and experimental investigations of a diode-pumped high-power continuous-wave 912 nm Nd:GdVO4 laser operation at room temperature

Based on the rate equation of Nd³⁺-doped quasi-three-level lasers, a theoretical model of diode-end-pumped continuous-wave 912 nm Nd:GdVO₄ laser is presented. Lasing threshold and slope efficiency considering reabsorption effect are calculated and analyzed. It is found that the output performance of 912 nm laser operating at room temperature is influenced remarkably by the reabsorption loss and spatial distribution of the pump beam and laser beam. In experiments, the output power and average slope efficiency of 912 nm laser were investigated under different conditions. After optimization at the parameters of laser medium, working temperature and spatial distribution of the pump beam, up to 16.2 W continuous-wave 912 nm laser output was obtained at incident pump power of 67.0 W, with an average slope efficiency of 41.7%, to the best of our knowledge, this is the highest output power of diode-pumped 912 nm Nd:GdVO₄ laser by far.     

Estimation of thermal lensing effect in the high-power end-pumped direct-cut crystal lasers

At this working, analytical (with Gaussian pump beam profile) and numerical FEM (with super-Gaussian pump beam profile) methods were compared for estimation of thermal lensing effect in the diode-end-pumped solid-state laser rods. These results were applied to the design and realization of a direct-cut (i.e., cut in right-angle ) crystal Nd:YVO₄ laser. The results showed that for such crystal (direct-cut), two methods obtained almost the same results, but slightly different from experimental results. However, estimation of thermal lensing effect led to realization of a diode-end-pumped Nd:YVO₄ cw high-power laser with good optical quality.     

Irradiation effects of CO2 laser parameters on surface morphology of fused silica

To understand the surface morphology evolution of fused silica induced by 10.6-μm CO2 laser irradiation at different parameters,this paper reports that optical microscopy,profilometry,and hydrophilicity tests are utilized to characterize the surface structure and roughness of the laser irradiated area. The results show that three typical surface morphologies and two typical hydrophilicity test images are observed at different laser powers and pulse durations. The correlations between surface temperature and surface morphology as well as hydrophilicity behaviours are presented. The different hydrophilicity behaviours are related to surface structures of the laser-induced crater and thermal diffusion area. The thermal diffusion length monotonously increases with increasing laser power and pulse duration. The crater width is almost determined by the laser beam size. The crater depth is more sensitive to the laser power and pulse duration than the crater width.     

激光输出不稳定性对激光与物质热作用的影响

研究了激光与物质相互作用中激光输出不稳定性对材料中温度场颁的影响以及减少这种影响的途径。首次在激光热传导方程中引入噪声项,推导了噪声影响下该激光热传导方程的解。研究发现,温度场的分布受噪声的影响,材料表面温度的涨落较大,而材料的深处涨落较小;温度场的涨落还和激光加热的过程有关,随激光加热时间的增长,温度场的涨落增大。此外,材料的热传导系数、热扩散率和发射率均对温度场的涨落有影响。文中还提出了减小激     

Periodic adjustment of the position of a laser beam spot on a semiconductor saturable absorber mirror in a passively mode-locked solid-state laser

A laser diode end-pumped passively mode-locked Nd:YVO₄ solid-state laser with a semiconductor saturable absorber mirror (SESAM), in which the intracavity laser beam spot on the SESAM can be adjusted periodically, is investigated. Inserting a rectangular prism (RP) into the laser cavity is a promising approach towards the goal of periodically moving the position of the focus spot of the intracavity pulse on the SESAM surface to avoid the long-time irradiation of the laser beam on the same position, thereby solving a series of problems caused by damage to the SESAM and greatly prolonging its usage life. The adjustment of the rectangular prism in the laser cavity does not break the stable continuous wave (CW) mode-locked condition. The laser generates a stable picosecond pulse sequence at 1064 nm with an output power of 3.6 W and a pulse width of 14 ps. The instabilities of the output power and the pulse width are 1.77% and 4.5%, respectively.     

Thermal effects of the diode end-pumped Nd:YVO4 slab

The thermal effects of the diode end-pumped Nd:YVO₄ slab laser crystal are investigated both analytically and numerically. The theoretical model is established with considering the divergence of the pump beam in the slab. A detailed theoretical analysis of the temperature, stress and the focal length of thermal lens are presented. Using 3D finite element analysis, an accurate numerical solution based on the theoretical model is achieved. Our analysis includes the thermal fracture damage of the thermally and optically anisotropic slab and the predicated values are compared with the experimental results.     

Influence of SiO2 additional layers on the laser induced damage threshold of Ta2O5 films

A series of Ta₂O₅ films with different SiO₂ additional layers including overcoat, undercoat and interlayer was prepared by electron beam evaporation under the same deposition process. Absorption of samples was measured using the surface thermal lensing (STL) technique. The electric field distributions of the samples were theoretical predicted using thin film design software (TFCalc). The laser induced damage threshold (LIDT) was assessed using an Nd:YAG laser operating at 1064 nm with a pulse length of 12 ns. It was found that SiO₂ additional layers resulted in a slight increase of the absorption, whereas they exerted little influence on the microdefects. The electric field distribution among the samples was unchanged by adding an SiO₂ overcoat and undercoat, yet was changed by adding an interlayer. SiO₂ undercoat. The interlayer improved the LIDT greatly, whereas the SiO₂ overcoat had little effect on the LIDT.     

电光调QCO2激光器的六温度模型理论与速率方程理论比较分析

分别利用速率方程理论和六温度模型理论对Q开关CO₂激光器动力学过程进行了理论分析比较,实验上测得电光调Q射频波导CO₂激光器脉冲激光建立时间及峰值功率与速率方程理论和六温度模型理论计算结果一致.但速率方程理论计算的激光脉冲宽度较“窄”,并且几乎没有拖尾,而六温度模型理论计算的脉冲激光波形有明显的拖尾,符合实际测量的波形.另外,六温度模型理论可以全面反映激光器工作气体中不同分子能级的能量转移过程,因此六温度模型理论分析更全面 关键词： 2激光器')" href="#">电光调QCO₂激光器 六温度模型理论 速率方程理论     

Semianalytical analysis of thermal effect in LD double-side-pumped rectangular laser crystal

A semianalytical method to analyze the thermal effect in a LD double-side-pumped rectangular laser crystal is put forward. Through the analysis of working characteristics of the laser crystal, a thermal model that matches actual situations of the laser crystal is established. General expressions of temperature field and thermal distortion field in the laser crystal can be obtained by a novel method to solve the heat conduction equation of orthotropic material. This semianalytical method can be used to calculate the temperature field and thermal distortion field in other LD double-side-pumped laser crystals and is applied to Nd:YVO₄ crystal in detail in this paper, and two methods of effectively reducing thermal distortion in the laser crystal are offered. Results show that a maximum temperature rise of 362.2 °C and a maximum thermal distortion of 5.55 μm are obtained in Nd:YVO₄ crystal when the output power of the two laser diodes are both 30 W. When the off-center distance is 0.6 mm, the maximum thermal distortion is reduced by 37.7%; when the thickness of the crystal is reduced from 2.0 mm to 1.4 mm, the maximum thermal distortion is reduced by 31.7%. Results in this paper can offer theoretical base for better solving thermal problems in laser system.     

Thermal affected zone obtained in machining steel XC42 by high-power continuous CO2 laser

A high-power continuous CO₂ laser (4 kW) can provide energy capable of causing melting or even, with a special treatment of the surface, vaporization of an XC42-steel sample. The laser–metal interaction causes an energetic machining mechanism, which takes place according to the assumption that the melting front precedes the laser beam, such that the laser beam interacts with a preheated surface whose temperature is near the melting point. The proposed model, obtained from the energy balance during the interaction time, concerns the case of machining with an inert gas jet and permits the calculation of the characteristic parameters of the groove according to the characteristic laser parameters (absorbed laser energy and impact diameter of the laser beam) and allows the estimation of the quantity of the energy causing the thermal affected zone (TAZ). This energy is equivalent to the heat quantity that must be injected in the heat propagation equation. In the case of a semi-infinite medium with fusion temperature at the surface, the resolution of the heat propagation equation gives access to the width of the TAZ.