The influence of coupled diffusion of heat and moisture on the state of stress in a plate

The fundamental results of previous reports on the coupling of the processes of diffusion of heat and moisture in solids are reviewed. The influence of the coupling on diffusion into an infinite plate from both its surfaces is discussed with the aim of clarifying what can and cannot be learned from such experiments. The nonuniformity of temperature and moisture content tends to cause nonuniform deformation. The stresses set up are computed for a homogeneous, isotropic plate. These self-equilibrating stresses first increase with time and then die out. For some combinations of material constants, the stresses undergo a reversal. For example, in some cases the surface stresses initially become compressive as moisture begins diffusing into the plate. Subsequently, as the interior of the plate increases in temperature due to the coupling effect, the surface stresses become tensile before eventually subsiding to zeroPublished in Mekhanika Kompozitnykh Materialov, No. 1, pp. 53–61, January–February, 1980.     

Combined bending and axial loading of beams made of materials with low shear strength

The effect of shear stresses on the deflection of glass-reinforced plastic beams in bending with axial loading is investigated in the case of hinged supports. The critical axial compressive load is determined with allowance for shear and the limiting value of the axial tensile load is estimated.Mekhanika Polimerov, Vol. 4, No. 1, pp. 124–130, 1968     

Effect of heat treatment on the distribution of residual stresses and the properties of epoxy polymers

Conclusions The analysis of the experimental data showed that heat treatment results in a reduction in the stressed state of a polymer, which affects the tensile strength of the material to a greater degree than the compressive strength. During heat treatment, significant changes take place in sections of the polymer damaged by the effect of residual compressive stresses and sections in which the residual stresses change sign. The quantitative relations in the change in the tensile strength of the material in these two sections make it possible to explain the mechanism of the effect of heat treatment and to predict its character.Translated from Mekhanika Kompozitnykh Materialov, No. 5, pp. 787–790, September–October, 1986.     

Nonuniform isothermal curing of cylindrical products made of polymeric composites

Conclusion By increasing the curing temperature and reducing the winding rate, it is possible to obtain compressive radial stresses in a cylindrical product during the entire curing stage — which should prevent loss of integrity during the curing operation. When the duration of the curing process is limited, the magnitude of the compressive stresses will depend in an extreme manner on curing temperature. Meanwhile, in the general case, ensuring minimal residual stresses will not ensure the absence of tensile radial stresses during curing.Translated from Mekhanika Kompozitnykh Materialov, No. 5, pp. 873–877, September–October, 1988.     

Effect of internal stresses on the wear resistance of epoxy coatings

The results of wear tests on ED-5 epoxy coatings are used to derive a relation between internal stresses, modulus of elasticity, and wear resistance. During wear the internal tensile stresses diminish, the rate of decrease depending on the initial stress state, the material of the abrading body, and the test conditions. The thickness of the coating affects wear resistance up to a certain value; for ED-5 the limiting thickness is 500 microns.Mekhanika Polimerov, Vol. 1, No. 2, pp. 123–128, 1965     

Results of an experimental investigation of the residual stresses in wound glass-reinforced plastics

The results of an experimental investigation of the residual stresses in wound glass-reinforced plastic rings are presented. The residual stresses were determined by the Davidenkov method. The dependence of the maximum tensile and compressive circumferential stresses on ring thickness and polymerization temperature is investigated. The experimental data are compared with the results of calculations based on the theory proposed in [1, 2].Moscow Power Engineering Institute. Translated from Mekhanika Polimerov, No. 6, pp. 1116–1119, November–December, 1970.     

Effect of the rate of deformation on the mechanical properties of compact bone tissue

Conclusions The results of this study show that the ultimate stress increases with increasing deformation rate from 10^–5 to 1 sec^–1 but the initial elasticity modulus remains virtually constant. A characteristic feature of bone tissue is the significant increase or even maximum in specific deformation energy for destruction in the range of deformation rates corresponding to normal physiological conditions for bone function. The deformation diagrams of human bone tissue for the same values of moisture content and deformation rate in tensile testing do not differ from the analogous curves for the bone tissue of cattle. Quantitatively, the ultimate stress ₁₁ and the initial elasticity modulus E₁ are 5–10% and 15–25% greater, respectively, than for cattle bone tissue, while the ultimate deformation eu is virtually the same. An increase in the moisture content of bone tissue leads to a more pronounced dependence of the mechanical parameters on the deformation rate.Translated from Mekhanika Kompozitnykh Materialov, No. 3, pp. 512–517, May–June, 1982.     

Anisotropy in the destruction of compact bone material

Conclusions 1. The nature of the destruction of compact bone material upon short-term static compressive and tensile stresses, as well as upon impact bending, is a function of the anistropy of the structure on the osteon level.2. The compact bone material of femoral bones of the age range studied is destroyed by shear for the types of stresses indicated.3. The nature of the destruction of samples of compact bone material for the stresses studied may be generalized for tubular bones.Kurgan Scientific-Research Institute of Experimental and Clinical Orthopedics and Traumatology. Translated from Mekhanika Polimerov, No. 2, pp. 319–324, March–April, 1978.     

Construction of the strength surface of structurally inhomogeneous materials in complex states of stress

The article describes a method of constructing strength surfaces based on the approximation of experimental data. The surface is a nonrotational convex shape, symmetrical about the diagonal of the principal stresses. The suggested method is suitable for a broad class of materials with compressive and tensile strength differing from each other, and in some special cases it coincides with the classical conditions of strength. In the example of concrete the article shows that theoretical results are comparable with the experiments.Translated from Teoreticheskaya i Prikladnaya Mekhanika, No. 19, pp. 20–24, 1988.     

Spectroscopic method of measuring the stresses at stress raisers in polymers

A method of measuring the mechanical stresses near stress raisers from the frequency shift of the IR absorption bands is proposed. The stresses at the edge of an ellipse as determined by IR spectroscopy, from the birefringence, and by theoretical calculation are compared. It is shown that the results coincide. The stress near the tip of a crack has been measured by the IR spectroscopy technique. It is shown that these stresses may be ten or more times greater than the external tensile stress.A. F. Ioffe Physicotechnical Institute, Academy of Sciences of the USSR, Leningrad. Translated from Mekhanika Polimerov, No. 1, pp. 167–170, January–February, 1970.     

Changes in the fine structure of polycaprolactam induced by hydrostatic pressure

The effect of high (up to 22,000 atm) hydrostatic pressure on the interplanar spacings and corresponding diffraction maxima in polycaprolactam has been investigated. The observations are interpreted in terms of the compressibility anisotropy relative to the amorphous and crystalline regions of the polymer and possible elastic deformation of the amorphous zones leading to tensile stresses in the crystalline regions that relax as the polymer ages owing to processes associated with changes in the conformations of the macromolecules and the number of crosslinks between segments.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, Vol. 4, No. 4, pp. 579–585, July–August, 1968.     

Winding fiber composites with additional pressure

Possibilities of compacting reinforced plastics by applying additional pressure have been established in which application of additional pressure is rational. The effect of this technological device on the magnitude of the initial stresses which arise in the wound construction in the relative thickness range k=1.01–1.15 has been studied.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, No. 5, pp. 793–796, September–October, 1972.     

Inelastic deformation and fracture of disordered fiber-reinforced composites

Conclusions Simulation of the process of nonlinear deformation and failure in the structure of a unidirectional epoxy glass plastic under transverse loading has indicated that equilibrium regions of failure receiving only hydrostatic compressive loading may form. The development of this region explains the high (up to 40%) nonlinearity of deformation diagrams under transverse biaxial compressive loading. The regions of nonlinear deformation of the epoxy matrix affect less markedly the nonlinearity of the macroscopic s* diagrams. This fact and also the formation and avalanchelike propagation of regions of complete failure explain the linear form of many diagrams corresponding to tensile and shear loading in the transverse plane. The relations of the nonlinear theory of elasticity make it possible to describe with sufficient accuracy the entire set of the calculated diagrams.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 5, pp. 621–628, September–October, 1993.Translated from Mekhanika Kompozitnykh Materialov, Vol. 29, No. 5, pp. 621–628, September–October, 1993.     

An analysis of moisture diffusion according to Fick’s law and the tensile mechanical behavior of a glass-fabric-reinforced composite

The properties of moisture diffusion parameters and their effect on the tensile mechanical behavior of a fabric composite (glass fiber/epoxy resin) in the warp and weft directions were investigated. The water up take by specimens conditioned in a humid environment under different relative humidities (0, 60, and 96% RH) at a constant temperature of 60°C was evaluated by weight gain measurements. The water absorption followed Fick’s diffusion law in the fabric composite. A comparison between the values obtained for the moisture diffusion coefficient and the equilibrium moisture content at the laboratory and those given by Loos and Springer showed that the parameters depended not only on the nature of materials, but also on environmental conditions. The effect of moisture absorption on tensile characteristics of the composite, which was tested in uniaxial tension in the warp and weft directions at constant imposed displacement rates up to failure, showed a significant reduction in the ultimate tensile strength of the specimens conditioned at 96% RH. Russian translation in Mekhanika Kompozitnykh Materialov, Vol. 45, No. 43, pp. 479-488, May-June, 2009.     

Initial stresses in filament-wound reinforced-plastic rings

Methods of experimentally determining the initial stresses in filament-wound GRP rings are examined and the effect of winding tension is investigated. It is shown that by varying the winding tension it is possible to exercise a considerable degree of control over the magnitude and distribution of the initial stresses.Institute of Polymer Mechanics, Academy of Sciences of the Latvian SSR, Riga. Translated from Mekhanika Polimerov, No. 3, pp. 505–511, May–June, 1969.     

Strengthening of glass-fiber-reinforced plastic under biaxial tension

Conclusions 1. The effect of axial tension, applied at the first stage of loading under biaxial tension, on the increase in the hoop strength of an oriented glass-fiber-reinforced plastic was observed. The increase in the hoop strength depends both on the value of the axial tensile load, and on the angle of winding of the fibers.2. The effect observed is in this case apparently independent of the condition of loading of the sample under biaxial tension.Institute of Mechanics, Academy of Sciences of the Armenian SSR, Erevan. Translated from Mekhanika Polimerov, No. 6, pp. 1025–1029, November–December, 1976.     

Study of moisture absorption by an organoplastic

Conclusion A complex experimental study of the state of sorbed moisture in a unidirectionally reinforced organoplastic was conducted. The methods of TG, DSC, DTA, and NMR showed that moisture absorption in OP is reversible up to 8%, the sorbed moisture does not crystallize in the temperature range from –70 to 0 °C, it is finely dispersely distributed and is in the strongly and weakly bound state, and there is almost no free moisture. The results of the sorption experiments conducted on OP and its structural components: microplastic and EDT-10 binder, in a wide range of temperature-humidity conditions and the data from physical studies showed that moisture absorption in the materials basically takes place by diffusion and is satisfactorily described by a phenomenological model based on the Fick equation.A method of accelerated determination of the sorption characteristics of anisotropic composite materials was developed, using the introduced concept of the fictitious diffusion coefficient and the extrapolation method of determining the limiting moisture content. The features of migration of moisture on the interface in a multiphase system were investigated, and the possibility of successive calculation estimation of the sorption characteristics of an organoplastic at different structural levels was demonstrated: components—unidirectionally reinforced composite—model laminated article. The tested phenomenological model of the sorption process and the experimentally obtained values of the characteristics of the material were the basis for a method of calculation determination of the resource of moisture-proofing properties of a model multilayer article of CM in nonstationary external conditions.Translated from Mekhanika Kompozitnykh Materialov, No. 4, pp. 624–632, July–August, 1990.     

Deformation of teflon in linear and plane states of stress

Teflon specimens have been deformed in accordance with various laws of variation of stress and strain with time under plane stress conditions. Fairly simple expressions describing the relation between the stresses and large (up to 60% relative to the initial dimensions) strains are constructed for a broad class of loading regimes.Scientific-Research Institute of Mathematics and Mechanics, A. A. Zhdanov Leningrad State University. Translated from Mekhanika Polimerov, Vol. 4, No. 4, pp. 742–746, July–August.     

Cutting of aramide fiber-reinforced plastics by Co2 laser

Comparative characteristics of aramide fiber reinforced plastics (AFRP) made by laser cutting or machining are presented. It is found that the strength of the specimens cut out by laser is 4–25% higher, while the moisture absorption is at least 2 times lower as compared to those cut out by machining. The deviation of the cutting edge size for AFRP 2 mm thick does not exceed 0.4 mm. Calculated and experimental data are given. The possibilities and conditions of cutting the AFRP up to 6 mm thick are determined.Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 3, pp. 375–384, May–June, 1999.     

Kinetics and consequences of "bleeding" of volatiles from plexiglas

The authors have studied the kinetics of "bleeding" during the heating of oriented and non-oriented plexiglas with accrued operating times of up to 16,000 h. They show that bleeding of the products of degradation of macromolecules from plexiglas is accompanied by a decrease in the volume of the polymer, which causes tensile stresses in the surface layers and may lead to surface cracking."Lenin Komsomol" Riga Red Banner Institute of Civil Aviation Engineers. Translated from Mekhanika Polimerov, No. 2, pp. 346–348, March–April, 1974.