Online deposition of nano‐aerosol for matrix‐assisted laser desorption/ionization mass spectrometry

An online nano‐aerosol sample deposition method for matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry is described in which matrix and analyte particles between 50 and 500 nm are aerodynamically focused onto a tight spot, ca. 200 µm in diameter, on the target plate under vacuum. MALDI analysis of the target is performed without additional sample preparation. The method is evaluated with insulin as the analyte and alpha‐cyano‐4‐hydroxycinnamic acid (CHCA) as the matrix. Two preparation modes are compared with conventional dried‐droplet deposition: mixture deposition where a single layer is deposited consisting of particles that contain both matrix and analyte, and layered deposition where an underlayer of matrix particles and an overlayer of analyte particles are deposited separately. Desalting is performed by adding ammonium sulfate to the solution used to generate the matrix aerosol. With mixture deposition, the optimum matrix‐to‐analyte mole ratio is about 500:1 compared with 5000:1 for the conventional dried‐droplet method. With layered deposition, the thicknesses of the matrix and analyte layers are more important determinants of the analyte signal intensity than the matrix‐to‐analyte mole ratio. Analyte signal intensities are independent of matrix layer thickness above 200 nm, and the optimum analyte signal is obtained with an analyte layer thickness of about 100 nm. Copyright © 2009 John Wiley & Sons, Ltd.     

Ready-made matrix-assisted laser desorption/ionization target plates coated with thin matrix layer for automated sample deposition in high-density array format.

The methodology for ready-made matrix-assisted laser desorption/ionization (MALDI) target plates covered with an optimized thin layer consisting of matrix and nitrocellulose has been developed. Piezoelectric microdispensing enabled sample depositions in a high-density array format of 2000 sample depositions on a conventionally sized target plate (45 x 47 mm). The sample depositions were made reproducibly in a fully automated mode by using an in-house developed computer-controlled piezoelectric flow-through microdispenser. Additionally, the piezoelectric technique facilitated significant analyte enrichment that increased the detection sensitivity. The MS signal was obtained rapidly, generally within ten laser pulses. An airbrush device was used to generate a fine spray of matrix and nitrocellulose dissolved in acetone. The acetone evaporated instantly when reaching the target plate leaving the entire surface with a thin and uniform matrix/nitrocellulose coating consisting of very small crystals of matrix embedded in the nitrocellulose. These crystals acted as a seed-layer on subsequent analyte depositions, rendering homogeneous sample spots when using alpha-cyano-4-hydroxycinnamic acid (CHCA) as matrix. The relative standard deviation of the signal intensity between spots was (20-30)% (n = 30). The detection sensitivity was improved by restricting the sample spot diameter to 300 microm. The spot size was affected by the deposition rate and the evaporation rate of the dispensed sample volume. Mass spectra of a 25-amol peptide mixture deposition were successfully recorded.     

分析保护剂补偿基质效应-气相色谱-质谱法快速测定水果中40种农药残留

建立了水果中40种农药化合物的气相色谱-质谱(GC-MS)多残留检测方法,评价了添加分析保护剂对农药残留分析的补偿基质效应和对定量结果可靠性的影响。采用可以溶于丙酮有机溶剂的聚乙二醇Polyethylene Glycol 400(PEG 400)和橄榄油作为保护剂组合进行定量分析。水果样品采用乙腈提取,微型固相萃取小柱净化,大体积进样,GC-MS选择离子监测(SIM)模式检测。40种农药化合物在1～200 μg/L范围内线性关系良好,线性相关系数在0.99以上,检出限(以信噪比为3计)为0.1～3.0 μg/L。除乐果外,其他化合物的添加回收率为75%～119%,相对标准偏差均小于16.6%。通过对添加分析保护剂的校准曲线与基质匹配校准曲线的定量准确性的比较,发现加入分析保护剂方法可以代替基质匹配校正方法,同时采用大体积进样和微型固相萃取净化相结合的方法,大大减少了样品前处理量。将所建立的分析保护剂方法用于苹果、桃子、橙子、香蕉和葡萄等水果样品的分析,基质补偿效应良好,有效地克服了水溶性分析保护剂对气相色谱分析有影响的缺点。     

Solvent-free matrix dry-coating for MALDI imaging of phospholipids

A fast and simple, solvent-free matrix deposition protocol was developed for positive ionization mode phospholipid analysis in tissues. Finely ground 2,5-dihydroxybenzoic acid was deposited onto sagittal mouse brain sections using a dry-coating technique, in which solid matrix particles were filtered directly onto the tissue through a 20-microm stainless steel sieve. Phospholipid signals were obtained directly off these sections, allowing acquisition of high-resolution MS images. These images were compared to those from serial sections that were spray-coated with a thin-layer chromatography (TLC) reagent sprayer. Signals obtained from the dry matrix deposition method were comparable to those from spray-coated sections, producing identical localization patterns with a simpler and faster sample preparation with virtually no analyte delocalization. This approach was found to yield highly reproducible results, eliminating much of the variance caused by operator differences, and making it an attractive alternative to the currently used matrix application methods.     

Application and evaluation of solvent-free matrix-assisted laser desorption/ionization mass spectrometry for the analysis of derivatized fullerenes

A variety of derivatized fullerenes have been studied by matrix-assisted laser desorption/ionization (MALDI) mass spectrometry. Of particular emphasis has been the evaluation of a recently introduced solvent-free sample/target preparation method. Solvent-free MALDI is particularly valuable in overcoming adverse solvent-related effects, such as insolubility and/or degradation of the sample. The method was applied to fullerene derivatives susceptible to decomposition under insufficiently "soft" MALDI conditions. Analytes included the hydrofullerene: C(60)H(36), fluorofullerenes: C(60)F(x) where x = 18, 36, 46, 48 and C(70)F(x) where x = 54, 56, methano-bridged amphiphilic ligand adducts to C(60) and the [4 + 2] cycloadduct of tetracene to C(60). The new solvent-free sample preparation is established as an exceedingly valuable addition to the repertoire of preparation protocols within MALDI. The MALDI mass spectra were of very high quality throughout, providing a testimony that "soft" MALDI conditions could be achieved. Using the [4 + 2] cycloadduct of tetracene to C(60) as the model analyte for direct comparison with solvent-based MALDI, the solvent-free approach led to less fragmentation and more abundant analyte ions. Applying solvent-free sample preparation, different matrix compounds have been examined for use in the MALDI of derivatized fullerenes, including sulfur, tetracyanoquinodimethane (TCNQ), 9-nitroanthracene (9-NA) and trans-2-[3-(4-tert-butylphenyl)-2-methyl-2- propenylidene]malononitrile (DCTB). DCTB was confirmed as the best performing matrix, reducing unwanted decomposition and suppression effects.     

Electrospray sample deposition for matrix-assisted laser desorption/ionization (MALDI) and atmospheric pressure MALDI mass spectrometry with attomole detection limits

Electrospray sample deposition was explored for matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS). In this method, nanoliter volumes of matrix/analyte mixture were electrosprayed from a high voltage biased (1-2 kV) fused-silica capillary onto a grounded MALDI plate mounted 100-500 microm from the capillary outlet. Electrospray deposition with these conditions produced sample spots 200-300 microm in diameter thus matching the laser spot size. Varying spray voltage and distance resulted in different crystal sizes and volatilization rates for alpha-cyano-4-hydroxycinnamic acid matrix. Best results were obtained when the sample was deposited as wet droplets as opposed to deposition as dried solid. Under 'wet-spray' conditions, 2-4 microm diameter crystals were formed and detection limits for several neuropeptides were 0.7-25 amol. Samples could be pre-concentrated on the plate by spraying continuously and allowing sample to evaporate in a small spot. Sample volumes as large as 580 nL were deposited yielding a detection limit of 35 pM for neurotensin 1-11. Electrospray sample deposition yielded similar results when using atmospheric pressure-MALDI coupled with a quadrupole ion trap mass spectrometer, except that the sensitivity was approximately seven-fold worse.     

Laserspray ionization using an atmospheric solids analysis probe for sample introduction

A newly introduced high sensitivity laserspray (LSI) mass spectrometry (MS) method that uses laser ablation of a matrix/analyte mixture at atmospheric pressure (AP) to obtain multiply charged ions from nonvolatile as well as high-mass compounds is now implemented using a simple probe device. The probe used in the LSI approach was originally designed for sample introduction into an AP ionization source using the atmospheric solids analysis probe (ASAP) method. Multiply charged mass spectra of peptides and proteins in 2,5-dihydroxybenzoic acid matrix were readily obtained on two mass spectrometers from different manufacturers with sample introduction using melting point tubes. Here we demonstrate rapid analysis by placing four peptide and protein samples on a single melting point tube. Mass spectra were obtained at high-resolution and using ion mobility spectrometry/MS.     

Supported liquid extraction in combination with LC‐MS/MS for high‐throughput quantitative analysis of hydrocortisone in mouse serum

A high‐throughput LC–MS/MS bioanalytical method was developed and validated for the determination of hydrocortisone in mouse serum via supported liquid extraction (SLE) in a 96‐well plate format. Although sample extracts from SLE result in similar matrix effects compared with conventional liquid–liquid extraction (LLE), greater analyte extraction recovery and much higher analysis throughput for the quantitative analysis of hydrocortisone in mouse serum were obtained. The current LC‐MS/MS method was validated for a concentration range of 2.00–2000 ng/mL for hydrocortisone using a 0.100 mL volume of mouse serum. The intra‐ and inter‐day precision and accuracy of the quality control samples at low, medium and high concentration levels showed ≤12.9% CV and ?3.4–6.2% bias for the analyte in mouse serum. Copyright © 2009 John Wiley & Sons, Ltd.     

Quantitative MALDI-MS<Superscript><Emphasis Type="Italic">n</Emphasis></Superscript> analysis of cocaine in the autopsied brain of a human cocaine user employing a wide isolation window and internal standards

Detection of drugs in tissue typically requires extensive sample preparation in which the tissue is first homogenized, followed by drug extraction, before the extracts are finally analyzed by LC/MS. Directly analyzing drugs in intact tissue would eliminate any complications introduced by sample pretreatment. A matrix-assisted laser desorption/ionization tandem mass spectrometry (MALDI-MS ⁿ ) method as been developed for the quantification of cocaine present in postmortem brain tissue of a chronic human cocaine user. It is shown that tandem mass spectrometry (MS² and MS³) increase selectivity, which is critical for differentiating analyte ions from background ions such as matrix clusters and endogenous compounds found in brain tissue. It is also shown that the use of internal standards corrects for signal variability during quantitative MALDI, which can be caused by inhomogeneous crystal formation, inconsistent sample preparation, and laser shot-to-shot variability. The MALDI-MS ⁿ method developed allows for a single MS³ experiment that uses a wide isolation window to isolate both analyte and internal standard target ions. This method is shown to provide improved precision [∼10–20 times reduction in percent relative standard deviation (%RSD)] for quantitative analysis compared to using two alternating MS³ experiments that separately isolate the target analyte and internal standard ions.     

The influence of matrix concentration and solvent composition on the results of MALDI MSI,with the aid of wet-interface matrix deposition

Imaging mass spectrometry is a powerful technique for the molecular analysis of tissue sections. As in many analytical methods, sample preparation is one of the main and most important steps to obtain results of good quality. Usually, the matrix concentration and solvent composition in different studies are taken for granted without any further consideration. In our studies, we aimed to find how matrix concentration and a type of solvent influence the signal. Moreover, we also aimed to find the relationship between these parameters, how they influence the spectra, and how they influence obtained ion maps. In our experiments, we used SunCollect®, which is a commercially available wet-interface system for matrix deposition. We decided to choose two matrix concentrations (2,5-dihydroxybenzoic acid [DHB]: 15 and 25 mg/mL; 9-aminoacridine [9AA]: 7 and 5 mg/mL) and two different water solutions of solvents in two different percentages for the matrices (DHB: 50% and 70% of methanol [MeOH] and acetonitrile [ACN]; 9AA 70% and 50% of ethanol [EtOH] and MeOH). In the end, the influence of these parameters on obtained spectra and ion maps was assessed.     

Solvent-free MALDI-MS for the analysis of biological samples via a mini-ball mill approach

An efficient, low sample load mini-ball mill (MBM) sample preparation procedure was developed for solvent-free MALDI analysis of peptides and proteins. Picomole sample amounts can be handled conveniently, with 30 s grinding times being sufficient. Matrix purity and molar analyte/matrix ratios are not as critical as with methods employing solvent. Ammonium salt is employed for protonation of the peptide and suppression of sodiation. This strategy allows for peptide mapping and other biochemical manipulations to be performed prior to MBM sample preparation and mass analysis. The analysis of bovine serum albumin (66 kDa) yielded good results, indicating that higher molecular weight proteins are accessible. A semi-solvent-free strategy by the MBM sample preparation method is also described.     

Development and validation of a qualitative screening method for the detection of exogenous anabolic steroids in urine by liquid chromatography-tandem mass spectrometry

A screening method for the urinary detection of 34 exogenous anabolic steroids has been developed. The method involves an enzymatic hydrolysis, liquid-liquid extraction and detection by liquid chromatography-tandem mass spectrometry. The use of some adducts such as [M+NH₄]⁺, [M+CH₃COO]⁻ and [M+H+MeOH]⁺ was necessary in order to detect some analytes at the required level (lower than 10 ng/ml). Two transitions were selected for each analyte. Different concentration factors have been studied in order to increase the sensitivity. A concentration factor of 50 was selected for the screening method although the high ion suppression observed under these conditions can hamper its application as a quantitative method. The method was validated and limits of detection were obtained by spiking ten different blank urine samples at five different concentration levels. Up to 29 analytes were detected in all spiked urines at the required level. Limits of detection between 1 and 10 ng/ml were obtained for most analytes which fulfil current requirements. The applicability of the method was shown by analysing positive samples.     

Quantitative determination of a nonpeptide antithrombotic in dog plasma by microbore high-performance liquid chromatography-tandem mass spectrometry utilizing pneumatically assisted electrospray ionization

A method has been developed and is described for the quantitative determination of a nonpeptide antithrombotic in dog plasma. The assay employs reversed phase microbore high-performance liquid chromatography in conjunction with tandem mass spectrometry utilizing pneumatically assisted electrospray ionization. The analyte and internal standard are isolated from the plasma matrix by solid-phase extraction. The mass spectrometer is operated in the positive ion multiple reaction monitoring mode and is set to detect the presence of a precursor-product ion pair for both the analyte and internal standard to generate product ion chromatograms for both species. The analyte is quantified by using weighted least-squares regression of the peak height ratio of drug:internal standard. The method provides linear response for plasma concentrations ranging from 5 ng/mL (25 pg on-column) to 2500 ng/mL. Statistical evaluation and examples of authentic sample assays are also presented.     

Matrix removal in state of the art sample preparation methods for serum by charged aerosol detection and metabolomics-based LC-MS

Investigations into sample preparation procedures usually focus on analyte recovery with no information provided about the fate of other components of the sample (matrix). For many analyses, however, and particularly those using liquid chromatography-mass spectrometry (LC-MS), quantitative measurements are greatly influenced by sample matrix. Using the example of the drug amitriptyline and three of its metabolites in serum, we performed a comprehensive investigation of nine commonly used sample clean-up procedures in terms of their suitability for preparing serum samples. We were monitoring the undesired matrix compounds using a combination of charged aerosol detection (CAD), LC-CAD, and a metabolomics-based LC-MS/MS approach. In this way, we compared analyte recovery of protein precipitation-, liquid-liquid-, solid-phase- and hybrid solid-phase extraction methods. Although all methods provided acceptable recoveries, the highest recovery was obtained by protein precipitation with acetonitrile/formic acid (amitriptyline 113%, nortriptyline 92%, 10-hydroxyamitriptyline 89%, and amitriptyline N-oxide 96%). The quantification of matrix removal by LC-CAD showed that the solid phase extraction method (SPE) provided the lowest remaining matrix load (48–123 μg mL⁻¹), which is a 10–40 fold better matrix clean-up than the precipitation- or hybrid solid phase extraction methods. The metabolomics profiles of eleven compound classes, comprising 70 matrix compounds showed the trends of compound class removal for each sample preparation strategy. The collective data set of analyte recovery, matrix removal and matrix compound profile was used to assess the effectiveness of each sample preparation method. The best performance in matrix clean-up and practical handling of small sample volumes was showed by the SPE techniques, particularly HLB SPE. CAD proved to be an effective tool for revealing the considerable differences between the sample preparation methods. This detector can be used to follow matrix compound elution during chromatographic separations, and the facile monitoring of matrix signal can assist in avoiding unfavourable matrix effects on analyte quantification.     

Improving the signal intensity and sensitivity of MALDI mass spectrometry by using nanoliter spots deposited by induction-based fluidics

A new contact-free, small droplet deposition method using an induction-based fluidics (IBF) technique to dispense nanoliter drops is described and evaluated for sample preparation in matrix-assisted laser desorption ionization mass spectrometry (MALDI-MS). The signal intensities available when using nanoliter spots are greater than those obtained with normal, microliter spots when the same amount of analyte is used. When using an ionic-liquid matrix, the improvement in sensitivity is equal to the concentration enhancement that was achieved by using smaller quantities of matrix. When using a conventional solid matrix, however, the increase in signal intensity shows a more complicated relationship to concentration. The approach of nanoliter deposition also supports multiple spotting to increase sample concentration and, thus, sample signal intensity. Nanoliter spotting not only improves the signal intensity and sensitivity achieved by MALDI-MS but also allows a major fraction of trace samples to be saved for other experiments, thus expanding the application of MALDI-MS to biological studies where sample quantity is limited.     

Automated MALDI Matrix Coating System for Multiple Tissue Samples for Imaging Mass Spectrometry

Uniform matrix deposition on tissue samples for matrix-assisted laser desorption/ionization (MALDI) is key for reproducible analyte ion signals. Current methods often result in nonhomogenous matrix deposition, and take time and effort to produce acceptable ion signals. Here we describe a fully-automated method for matrix deposition using an enclosed spray chamber and spray nozzle for matrix solution delivery. A commercial air-atomizing spray nozzle was modified and combined with solenoid controlled valves and a Programmable Logic Controller (PLC) to control and deliver the matrix solution. A spray chamber was employed to contain the nozzle, sample, and atomized matrix solution stream, and to prevent any interference from outside conditions as well as allow complete control of the sample environment. A gravity cup was filled with MALDI matrix solutions, including DHB in chloroform/methanol (50:50) at concentrations up to 60 mg/mL. Various samples (including rat brain tissue sections) were prepared using two deposition methods (spray chamber, inkjet). A linear ion trap equipped with an intermediate-pressure MALDI source was used for analyses. Optical microscopic examination showed a uniform coating of matrix crystals across the sample. Overall, the mass spectral images gathered from tissues coated using the spray chamber system were of better quality and more reproducible than from tissue specimens prepared by the inkjet deposition method.     

Solid-phase microextraction combined with surface-enhanced laser desorption/ionization introduction for ion mobility spectrometry and mass spectrometry using polypyrrole coatings

The successful application of polypyrrole (PPY) solid-phase microextraction (SPME) coatings as both an extraction phase and a surface to enhance laser desorption/ionization (SELDI) of analytes is reported. This SPME/SELDI fiber integrates sample preparation and sample introduction on the tip of a coated optical fiber, as well as acting as the transmission medium for the UV laser light. Using ion mobility spectrometry (IMS) detection, the signal intensity was examined as a function of extraction surface area and concentration of analyte. The linear relationship between concentration and signal intensity shows potential applicability of this detection method for quantitative analysis. Extraction time profiles for the fiber, using tetraoctylammonium bromide as test analyte, illustrated that equilibrium can be reached in less than one minute. To investigate the performance of the PPY coating, the laser desorption profile was studied. The fiber was also tested using a quadrupole time-of-flight (Q-TOF) mass spectrometer with leucine enkephalin as test analyte. Since no matrix was used, mass spectra free from matrix background were obtained. This novel SPME/SELDI fiber is easy to manufacture, and is suitable for studying low-mass analytes because of the intrinsic low background. These findings suggest that other types of conductive polymers could also be used as an extraction phase and surface to enhance laser desorption/ionization in mass spectrometry.     

A solvent‐free matrix application method for matrix‐assisted laser desorption/ionization imaging of small molecules

Matrix application continues to be a critical step in sample preparation for matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry imaging (MSI). Imaging of small molecules such as drugs and metabolites is particularly problematic because the commonly used washing steps to remove salts are usually omitted as they may also remove the analyte, and analyte spreading is more likely with conventional wet matrix application methods. We have developed a method which uses the application of matrix as a dry, finely divided powder, here referred to as dry matrix application, for the imaging of drug compounds. This appears to offer a complementary method to wet matrix application for the MALDI‐MSI of small molecules, with the alternative matrix application techniques producing different ion profiles, and allows the visualization of compounds not observed using wet matrix application methods. We demonstrate its value in imaging clozapine from rat kidney and 4‐bromophenyl‐1,4‐diazabicyclo(3.2.2)nonane‐4‐carboxylic acid from rat brain. In addition, exposure of the dry matrix coated sample to a saturated moist atmosphere appears to enhance the visualization of a different set of molecules. Copyright © 2010 John Wiley & Sons, Ltd.     

Improved silica xerogel film processing for MALDI-TOF–MS quantitative analysis of peptides and small molecules

In this work, sol–gel derived silica films were prepared for direct desorption/ionization of organic compounds in MALDI-TOF–MS analysis with the aim of improving method precision and of reducing interfering signals at low m/z values. Two commonly used MALDI matrices, 2,5-dihydroxybenzoic acid (DHB) and α-cyano-4-hydroxycinnamic acid (CHCA), were incorporated into the sol–gel network in order to absorb laser energy and to induce analyte desorption/ionization with low or absent background signals in the mass spectra. To achieve a reproducible xerogel film formation, experimental parameters for its deposition were optimized. The gel matrices were characterized by Fourier Transform Infrared (FT-IR) spectroscopy, X-ray Diffraction (XRD), and Scanning Electron Microscopy (SEM) analysis. The results proved the embedding of the matrix molecules in a disperse form into the homogeneous sol–gel material. The sol–gel matrix was then tested for the qualitative and quantitative analysis of two reference peptides, such as Bradykinin and P₁₄R. In addition, spectral quality and method performance were assessed for quantitation of melamine, a low-molecular weight compound of food safety concern. In all cases, high quality spectra and excellent mass accuracy (between 3.5 and 13 ppm) were observed. Furthermore, the experimental results evidenced a significant improvement of the measurement repeatability on spot and between spots (relative standard deviation <10%), with respect to the traditional dried-droplet sample deposition method. Good sensitivity and linearity in the concentration range explored were obtained for peptides and melamine, demonstrating the suitability of the sol–gel-based matrix to be used for quantitative analysis.