Determination of fission product ruthenium by isotope dilution mass spectrometry

Isotope dilution mass spectrometry using enriched isotope⁹⁶Ru as a spike was applied to the determination of ruthenium as a fission product. Ruthenium in the solution was oxidized to RuO₄ by Ce/IV/ and separated from coexisting metal elements by distillation. Silica-gel technique was employed to enhance ion current of ruthenium in the mass spectrometric measurement. The lower detection limit was 0.005 g ml^–1 and the relative standard deviations /n=3/ for 1.2 and 0.05 g ml^–1 of ruthenium were 0.2 and 0.5%, respectively.     

Fourth-derivative spectrophotometric determination of neodymium in mixed rare earths with methyl thymol blue and cetylpyridinium chloride

A sensitive and selective method is described for the determination of neodymium in mixed rare earths using fourth-derivative spectrophotometry. The method is based on the absorption spectra of 4f electron transitions of the complex of neodymium with methyl thymol blue and cetylpyridinium chloride. The influence of various instrumental parameters and reaction conditions for maximum colour development are investigated. The calibration curve is linear over the range 0–3.5 g ml^–1 neodymium. The relative standard deviation for determination of 1.4 g ml^–1 neodymium (n = 7) is 1.6%. The detection limit (signal-to-noise ratio = 3) is 0.2 g ml^–1.     

Differential pulse voltammetric methods for the simultaneous estimation of uranium-iron and uranium-cadmium mixtures in solution

Differential pulse voltammetric methods have been developed for the simultaneous estimation of the constituents of uranium-iron and uranium-cadmium mixtures in solution. A mixture of 1M H₃PO₄–1M KH₂PO₄ (with a pH1.5), was found to be the most ideal supporting electrolyte for both methods, among many that were evaluated for their suitability. In uranium-iron mixtures the calibration for iron was found to be linear up to 150 g ml^–1 (r²=0.9986), while that of uranium up to 500 g ml^–1 (r²=0.999). Iron at 6.7 g ml^–1 level could be determined in the presence of 800 fold uranium (wt/wt) without significant interference. Uranium at 21 g ml^–1 level could be analyzed with 5-fold iron (wt/wt). This upper limit of iron was due to the precipitation of iron as phosphate. In the case of uranium — cadmium mixtures, cadmium calibration for cadmium was found to be linear up to 1300 g ml^–1 (r²=0.9993). Concentration levels of 4.6 g ml^–1 Cd could be determined at a 500-fold excess (wt/wt) of uranium. Uranium calibration was linear up to 500 g ml^–1 (r²=0.999) and 21 g ml^–1 uranium could tolerate up to a 1000-fold excess of cadmium (wt/wt). Both procedures could tolerate 10 g ml^–1 levels of metal ions, such as chromium, copper, manganese, molybdenum and vanadium.     

Simultaneous determination of aluminium and iron in glasses,phosphate rocks and cement using first- and second-derivative spectrophotometry

First- and second-derivative spectrophoto-metric methods for the simultaneous determination of aluminium and iron in their mixtures are described. The methods are based on the colored complexes formed by aluminium and iron with hematoxylin in the presence of cetyltrimethylammonium bromide as a surfactant. The zero-crossing method has been utilized to measure the first- and second-derivative value of the derivative spectrum. Aluminium (0.05–1 gml^-1) could be determined in the presence of iron (0.09–1.6 gml^-1) and vice versa. The detection limits of aluminium and iron are 0.01 and 0.09 gml^-1, respectively in the first-derivative mode and 0.014 and 0.1 gml^-1 in the second-derivative mode. The proposed method has been applied to the simultaneous determination of aluminium and iron in glasses, phosphate rocks, cement and magnesite alloy.     

Spectrophotometric and derivative spectrophotometric determination of palladium(II) using pyridopyridazine dithione in the presence of non-ionic surfactant

Pyridopyridazine dithione (PPD) was synthesized as a new sensitive and selective reagent for spectrophotometric and derivative spectrophotometric determination of palladium(II). In aqueous and micellar medium, PPD forms 1:4 complexes having molar absorptivities of 4.68 × 10⁴ and 5.74 × 10⁴lmol^–1 cm^–1 at 570 and 615 nm, respectively. Beer's law was obeyed up to 2.2 and 2.5 g ml^–1 with detection limits of 0.2 and 0.1g ml^–1. The relative standard deviations for 1.23g ml^–1 were 2.6 and 1.3%, in the absence and presence of Triton X-100. In fourth-derivative mode, the regression equation, linear range, detection limit and RSD for 0.075 g ml^–1 wereD ₄ = 4.3C + 1.5 × 10^–3, 0.013 – 0.23 g ml^–1, 3.7 ng ml–1 and 0.78%, respectively. The ionization constants of the reagent and stability constants of the complexes were evaluated. The method is free from interference by most common metal ions and anions. The method was applied for determination of palladium in activated charcoal.     

Estimation of inorganic phosphate in aqueous solutions of DNA: A modification of the Berenblum-Chain method

Some modifications of the stannous chloride reduction method for the estimation of inorganic phosphate reported by Berenblum-Chain are suggested. By this method, it is possible to measure 25 g l^–1 of phosphorus /P/ as inorganic phosphate in the presence of macromolecules like deoxyribonucleic acid /100 g ml^–1/, as compared to 200 g l^–1 of P by the original method. If a larger sample volume /30 ml/ is used, even 5 g l^–1 of P can be measured.     

Flow-injection extraction-spectrophotometric determination of permanganate with the triphenylsulphonium cation

Summary Permanganate can be determined spectrophotometrically at 548 nm after flow-injection extraction into chloroform of the ion-associate triphenylsulphonium permanganate. The carrier stream was a pH 6 buffer containing 10% (w/v) ammonium fluoride and the reagent stream was 0.10% (w/v) triphenylsulphonium chloride. The injection rate was 20 h^–1. The calibration graph is linear up to 40 g ml^–1 and the detection limit is 1.10 g ml^–1 Mn(VII), based on injection volumes of 250 l. The system has been applied to the determination of manganese in steels and a cupro-nickel alloy.     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

Extractive spectrophotometric determination of dioxouranium(VI) with the sodium salt of hexamethyleneiminecarbodithioate

The optimum conditions for the extractive spectrophotometric determination of dioxouranium(VI) with hexamethyleneiminecarbodithioate(HMICdt) have been established. Dioxouranium(VI) reacts with this ligand at pH 4.5 to form a yellowish-orange uncharged 12 metal-ligand complex which can be extracted by chloroform. The calibration graph was linear in the range of 1–20 g ml^–1 of dioxouranium(VI) at 335 nm. The molar absorptivity of the extracted species is 5.952×10³ l mol^–1 cm^–1 with Sandell's sensitivity of 0.04 g cm^–2. The average of 10 determinations of dioxouranium was 49.75 g for the samples containing 50 g of U(VI) and the variation from the mean at 95% confidence limit was 49.75±0.5955.     

Spectrophotometric determination of vanadium(IV) in the presence of vanadium(V) using Br-PADAP

In the present paper, a simple and sensitive method is proposed for vanadium(IV) determination in the presence of vanadium(V). This is based on the oxidation of vanadium(IV) present in the sample to vanadium(V) by addition of iron(III) cation, followed by a complexation reaction of iron(II) with the spectrophotometric reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP). The iron(II) reacts with Br-PADAP immediately, forming a stable complex with a large molar absorptivity. The vanadium(IV) determination is possible, with a calibration sensitivity of 0.549 g ml^–1, for an analytical curve of 18.8 ng ml^–1 to 2.40 g ml^–1, molar absorptivity of 2.80 × 10⁴ 1 mole^–1 cm^–1 and a detection limit of 5.5 ng ml^–1. Selectivity was increased with the use of EDTA as a masking agent. The proposed method was applied for the vanadium(IV) determination in the presence of several amounts of vanadium(V). The results revealed that 200 g of vanadium(V) do not interfere with determination of 5.00 g of vanadium(IV). The precision and the accuracy obtained were satisfactory (R. S. D.<2%).     

Photometrische Bestimmung von Bor in hochreinen Chemikalien

Zusammenfassung Bor reagiert in Form des Tetrafluoroboratkomplexes mit dem basischen Farbstoff Methylenblau unter Bildung eines mit 1,2-Dichlorethan extrahierbaren Ionenassoziatkomplexes. Die optimalen Bedingungen für die photometrische Bestimmung von Mikromengen Bor werden ermittelt und das vorgestellte Verfahren hinsichtlich Empfindlichkeit, Genauigkeit und kleinster bestimmbarer Menge charakterisiert.Die Borbestimmung ist im Bereich von 0,25–2,5 g Bor mit einer relativen Standardabweichung von 3,8% für 1,0 g Bor möglich. Der molare Extinktionskoeffizient beträgt ₆₆₅=8,2·10⁴1·mol^–1·cm^–1, die Nachweisgrenze nach Kaiser 0,125 g Bor.Das Verfahren wurde zur Bestimmung von 10^–6 bis 10^–5% Bor in folgenden hochreinen Chemikalien eingesetzt: Methanol, Ethanol, Isopropanol, Aceton, Mineralsäuren, Essigsäure, Ammoniak und Wasserstoffperoxid.

---

Photometric determination of boron in high-purity chemicals

Summary Boron reacts with fluoride to form borofluoride which itself reacts with the basic dye methylene blue forming a complex which can be extracted into 1,2-dichloroethane. Optimum conditions were established for the determination of microamounts of boron by an extraction-photometric method. The procedure presented has been characterized with regard to sensitivity, precision and detection limit.Boron can be determined within a range from 0.25 to 2.5 g with a relative standard deviation s _rel=3.8% for 1 g B. The absorptivity is ₆₆₅=8.2·10⁴1·mol^–1·cm^–1, the detection limit according to Kaiser was found to be 0.125 g B.The procedure was used to analyse high-purity chemicals (10^–6–10^–5% B) such as organic solvents, mineral acids, acetic acid, ammonia, hydrogen peroxide etc.

     

ET-AAS in the Analysis of high-purity mercury

ET-AAS is investigated for the analysis of high purity mercury. Two possibilities are proposed: ET-AAS determination of trace analytes in the presence of high mercury concentrations or after matrix separation by reduction. The ET-AAS analysis of high-purity mercury under optimal instrumental parameters permits fast and reproducible determination of 0.03 gg^–1 Al, Cd and Mn; 0.05 gg^–1 Cu, Co, Cr, Fe, Ni and Pb and 0.2 gg^–1 V. Preliminary mercury matrix reductive separation with ascorbic acid allows determination of 0.005 gg^–1 Cd, 0.02 gg^–1 Cu, Cr and Mn, 0.03 g g^–1 Co, Ni and Pb, 0.05 g g^–1 Al and Fe and 0.1 gg^–1 V, but the reproducibility is lower. The main advantage of the second procedure is that it avoids laboratory and instrument pollution with toxic mercury.     

Determination of pyrimethanil and kresoxim-methyl in soils by headspace solid-phase microextraction and gas chromatography-mass spectrometry

A method using headspace solid-phase microextraction (HS-SPME) then gas chromatography–mass spectrometry with selected ion monitoring (GC–MS, SIM) has been developed for determination of trace amounts of the fungicides pyrimethanil and kresoxim-methyl in soil and humic materials. Both fungicides were extracted on to a fused-silica fibre coated with 85 m polyacrylate (PA). Response-surface methodology was used to optimise the experimental conditions. For soil samples the linear dynamic range of application was 0.004–1.000 g g^–1 for pyrimethanil and 0.013–1.000 g g^–1 for kresoxim-methyl. The detection limits were 0.001 g g^–1 and 0.004 g g^–1 for pyrimethanil and kresoxim-methyl, respectively. HP-SPME–GC–MS analysis was highly reproducible—relative standard deviations (RSD) were between 6.7 and 12.2%. The method was validated by analysis of spiked matrix samples and used to investigate the presence of pyrimethanil and kresoxim-methyl above the detection limits in soil and humic materials.     

Spectrofluorimetric flow-injection determination of cerium in carbon and low alloy steels

Cerium can be determined spectrofluorimetrically (_em 350 nm, _ex 260 nm) based on the relatively intense native fluorescence of the cerium(III) aquo-ion. The main potential interference in the analysis of steel from iron(III), cerium(IV) and chromium(VI) are removed by use of a carrier solution containing 2.5% w/v hydroxylammonium chloride. The slight residual interference from iron(II) can be corrected by a matrix matching factor linearly related to the amount of iron present. The calibration graphs are linear over the range 0–7 g ml^–1 based on 250 l injection volumes. The sampling rate was 30 h^–1. The relative standard deviation was 2.0% (n=5) at 3 g ml^–1 cerium. The system has been applied to the determination of cerium in carbon or low alloy steels.     

Chemical composition of T-21 silica tubing and implications for neutron activation analysis

T-21 silica, a commonly used encapsulation material in neutron activation analysis of small samples, was analyzed by INAA to determine trace levels of the following impurities: Na, Sc, Cr, Fe, Co, Ni, Zn, Br, Sb, La, Ce, Sm, Tb, Hf and Au. In the unprocessed form supplied by the manufacturer, pieces of T-21 weighing 50 mg contain 6·10^–2 g Na; 9·10^–3 g Fe; 3·10^–7–7·10^–6 g light REE, Sc and Hf and 4·10^–8 g Tb and Au. In a series of glass-blowing steps, in which unfiltered gases were used for fuel, and cleaning steps, in which reagent grade aqua regia was used, irradiation vials were produced which contain higher average levels of Sc, La, Sm, Tb and Hf, by factors ranging from 1.3 for Sm to 11.5 for La, and lower average levels of Co, Na and Fe, by factors of 1.4, 2.0 and 4.0, respectively, than the unprocessed material. These contamination levels lead to blank corrections of 21% for La, 2.6% for Ce and 3.0% for Hf in 40 g samples of refractory inclusions from carbonaceous chondrites, if counted in their irradiation vials.     

Fällungsanalyse im Mikrogrammbereich: Eine neue Methode

Zusammenfassung Eine neue Methode zur Durchführung gravimetrischer Bestimmungen im Mikrogrammbereich wurde beschrieben; diese beruht im wesentlichen darauf, daß der Niederschlag nicht mehr zusammen mit dem Filter, sondern nach Überführen mit einem geeigneten Lösungsmittel in einem separaten Wägegefäß gewogen wird.Die dazu nötigen Geräte und deren Herstellung wurden beschrieben. Nach dieser Methode wurden folgende Bestimmungen mit zufriedenstellender Richtigkeit durchgeführt: 2,5–25g Al, 5–50g Cu und 5–50g Zn mit Oxin, 2,5–25g Fe(III) und 2,5–25g Ti(IV) mit N-Benzoyl-phenylhydroxylamin, 5–50g Ni und 5–50g Cu mit Salicylaldoxim, 2,5–50g Co(II) und 2,5–50g Fe(III) mit -Nitroso--naphthol sowie 5–50g Chlorid als Silberchlorid.

---

Precipitation analysis in the microgram-scale: A new method

Summary A new method for gravimetric determinations in the microgram-scale is described. This method is based on the fact that the precipitate is not weighed together with the filter but is transferred to a separate weighingvessel using a suitable solvent. The necessary simple devices and their use are described. The following determinations were carried out with satisfying accuracy: 2,5–25g Al, 5–50g Cu and 5–50g Zn with Oxine, 2,5–25g Fe and 2,5–25g Ti withN-benzoylphenylhydroxylamine, 5–50g Ni and 5–50g Cu with salicylaldoxime, 2,52–50g Co and 2,5–50g Fe with -nitroso--naphthol and 5–50g chloride as silver chloride.

     

Zur Bestimmung N-substituierter Aniline mit Natriumchlorit

Zusammenfassung Es wird eine photometrische Bestimmungsmethode beschrieben für Anilin (40–720 g/ml), Monoäthylanilin (90–1650 g/ml) und Diäthylanilin (100–1600 g/ml) mit Natriumchlorit in äthanolisch-wäßrigen Lösungen, sowie für Diäthylanilin (85–1140 g/ml) und Dimethylanilin (30–330 g/ml) neben den primären und sekundären Aminen in essigsaurer Lösung mit demselben Reagens. Das Verfahren liefert gute Ergebnisse.

---

Summary A photometric procedure is described for the determination of aniline (40–720 g/ml), monoethylaniline (90–1650 g/ml), and diethylaniline (100–1600 g/ml) with sodium chlorite in aqueous ethanolic solutions and of diethylaniline (85–1140 g/ml) and dimethylamline (30 to 330 g/ml) in presence of the primary and secondary amines in acetic acid solution using the same reagent. Good results have been obtained,

     

Nuclear interferences of uranium and thorium in a reactor neutron activation analysis determination of cerium using the radionuclides141Ce and143Ce

The interference contributions of uranium and thorium to the determination of cerium based on radionuclides¹⁴¹Ce and¹⁴³Ce produced by irradiation in a reactor core was determined. The values of the interference contributions for¹⁴¹Ce were 0.28±0.01 g Ce/g U and /2.01±0.05/x10^–3 g Ce/g Th, and for¹⁴³Ce 1.33±0.03 g Ce/g U and /9.0±0.2/x10^–3 g Ce/g Th.     

Extractive spectrophotometric determination of niobium(V) using 3-hydroxyflavone

A simple, rapid method for the spectrophotometric determination of niobium in trace amounts is presented, employing 3-hydroxyflavone as a ligand for the complexation of the metal ion and extracting the coloured complex into chloroform from 4M HClO₄ solution. Beer's law is obeyed in the range 0.0 to 3.2 g ml^–1 Nb(V), with a lower working limit of 0.1 g ml^–1 Nb(V). Molar absorptivity and Sandell's sensitivity of the complex at 395 nm are 4.088 × 10⁴l mol^–1 cm^–1 and 0.002g Nb(V) cm^–2, respectively. The stoichiometry of the complex is established as 12 by Job's and mole ratio methods. The method is free from the interference of a large number of analytically important elements. The proposed system handles satisfactorily the analysis of several samples of varying complexity. The results are highly reproducible with a relative standard deviation of 0.34% for 20 g of Nb.