Layer-by-layer assembled multilayer TiO(x) for efficient electron acceptor in polymer hybrid solar cells

We demonstrate that TiO(x) nanocomposite films fabricated using electrostatic layer-by-layer (LbL) assembly improve the power conversion efficiency of photovoltaic cells compared to conventional TiO(x) films fabricated via the sol-gel process. For this study, titanium precursor/poly(allylamine hydrochloride) (PAH) multilayer films were first deposited onto indium tin oxide-coated glass to produce TiO(x) nanocomposites (TiO(x)NC). The specific effect of the LbL processed TiO(x) on photovoltaic performance was investigated using the planar bilayer TiO(x)NC and highly regioregular poly(3-hexylthiophene) (P3HT) solar cells, and the P3HT/LbL TiO(x)NC solar cells showed a dramatic increase in power efficiency, particularly in terms of the short current density and fill factor. The improved efficiency of this device is mainly due to the difference in the chemical composition of the LbL TiO(x)NC films, including the much higher Ti(3+)/Ti(4+) ratio and the highly reactive facets of crystals as demonstrated by XPS and XRD measurement, thus enhancing the electron transfer between electron donors and acceptors. In addition, the grazing incidence wide-angle X-ray scattering (GIWAXS) study revealed the presence of more highly oriented P3HT stacks parallel to the substrate on the LbL TiO(x)NC film compared to those on the sol-gel TiO(x) films, possibly influencing the hole mobility of P3HT and the energy transfer near and at the interface between the P3HT and TiO(x) layers. The results of this study demonstrate that this approach is a promising one for the design of hybrid solar cells with improved efficiency.     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

In situ current voltage measurements for optimization of a novel fullerene acceptor in bulk heterojunction photovoltaics

The evaluation of the power conversion efficiency (PCE) of new materials for organic bulk heterojunction (BHJ) photovoltaics is difficult due to the large number of processing parameters possible. An efficient procedure to determine the optimum conditions for thermal treatment of polymer‐based bulk heterojunction photovoltaic devices using in situ current‐voltage measurements is presented. The performance of a new fullerene derivative, 1,9‐dihydro‐64,65‐dihexyloxy‐1,9‐(methano[1,2] benzomethano)fullerene[60], in BHJ photovolatics with poly(3‐hexylthiophene) (P3HT) was evaluated using this methodology. The device characteristics of BHJs obtained from the in situ method were found to be in good agreement with those from BHJs annealed using a conventional process. This fullerene has similar performance to 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐methano fullerene in BHJs with P3HT after thermal annealing. For devices with thickness of 70 nm, the short circuit current was 6.24 mA/cm² with a fill factor of 0.53 and open circuit voltage of 0.65 V. The changes in the current‐voltage measurements during thermal annealing suggest that the ordering process in P3HT dominates the improvement in power conversion efficiency. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

聚3-己基噻吩：非富勒烯太阳能电池中的量子效率损失和电压损失

From the industrial perspective, poly(3-hexylthiophene) (P3HT) is one of the most attractive donor materials in organic photovoltaics. The large bandgap in P3HT makes it particularly promising for efficient indoor light harvesting, a unique advantage of organic photovoltaic (PV) devices, and this has started to gain considerable attention in the field of PV technology. In addition, the up-scalability and long material stability associated with the simple chemical structure make P3HT one of the most promising materials for the mass production of organic solar cells. However, the solar cells based on P3HT has a low power conversion efficiency (PCE), which is less than 11%, mainly due to significant voltage losses. In this study, we identified the origin of the high quantum efficiency and voltage losses in the P3HT: non-fullerene based solar cells, and we proposed a strategy to reduce the losses. More specifically, we observed that: 1) the non-radiative decay rate of the charge transfer (CT) states formed at the donor–acceptor interfaces was much higher for the P3HT: non-fullerene solar cells than that for the P3HT: fullerene solar cells, which was the main reason for the more severely limited photovoltage; 2) the origin of the high non-radiative decay rate in the P3HT: non-fullerene solar cell could be ascribed to the short packing distance between the P3HT and non-fullerene acceptor molecules at the donor–acceptor interfaces (DA distance), which is a rarely studied interfacial structural property, highly important in determining the decay rate of CT states; 3) the lower voltage loss in the state-of-the-art P3HT solar cell based on the 2, 2'-((12, 13-bis(2-butyldecyl)-3, 9-diundecyl-12, 13-dihydro-[1, 2, 5]-thiadiazolo[3, 4-e]thieno[2', 3': 4', 5']thieno[2', 3': 4, 5]p-yrolo[3, 2-g]thieno[2', 3': 4, 5]thieno[3, 2-b]indole-2, 10-diyl)bis(methanelylidene))bis(5, 6-dichloro-1H-indene-1, 3(2H)-dion-e) (ZY-4Cl) acceptor could be associated with the better alignment of the energy levels of the active materials and the longer DA distance, compared to those based on the commonly used acceptors. However, the DA distance was still very short, limiting the device voltage. Thus, improving the performance of the P3HT based solar cells requires a further increase in the DA distance. Our findings are expected to pave the way for breaking the performance bottleneck of the P3HT based solar cells.     

Quantitative nanoorganized structural evolution for a high efficiency bulk heterojunction polymer solar cell

We have developed an improved small-angle X-ray scattering (SAXS) model and analysis methodology to quantitatively evaluate the nanostructures of a blend system. This method has been applied to resolve the various structures of self-organized poly(3-hexylthiophene)/C61-butyric acid methyl ester (P3HT/PCBM) thin active layer in a solar cell from the studies of both grazing-incidence small-angle X-ray scattering (GISAXS) and grazing-incidence X-ray diffraction (GIXRD). Tuning the various length scales of PCBM-related structures by a different annealing process can provide a flexible approach and better understanding to enhance the power conversion of the P3HT/PCBM solar cell. The quantitative structural characterization by this method includes (1) the mean size, volume fraction, and size distribution of aggregated PCBM clusters, (2) the specific interface area between PCBM and P3HT, (3) the local cluster agglomeration, and (4) the correlation length of the PCBM molecular network within the P3HT phase. The above terms are correlated well with the device performance. The various structural evolutions and transformations (growth and dissolution) between PCBM and P3HT with the variation of annealing history are demonstrated here. This work established a useful SAXS approach to present insight into the modeling of the morphology of P3HT/PCBM film. In situ GISAXS measurements were also conducted to provide informative details of thermal behavior and temporal evolution of PCBM-related structures during phase separation. The results of this investigation significantly extend the current knowledge of the relationship of bulk heterojunction morphology to device performance.     

Toward the Realization of A Practical Diketopyrrolopyrrole‐Based Small Molecule for Improved Efficiency in Ternary BHJ Solar Cells

An easily accessible DPP‐based small molecule ( DMPA‐DTDPP ) has been synthesized by a simple and efficient route. The resulting molecule, when incorporated into a P3HT:PCBM‐based BHJ solar cell, is found to significantly improve the efficiency. The utility of DMPA‐DTDPP as an additive yields an increase in the short circuit current density (J_sc) because DMPA‐DTDPP serves as an energy funnel for P3HT excitons at the P3HT:PCBM interfaces, resulting in an improved overall power conversion efficiency, compared to the P3HT:PCBM control device. Considering the trouble‐free and cost effective synthesis of DMPA‐DTDPP , it may prove very useful in high‐performance solar cells.     

聚3-己基噻吩：非富勒烯太阳能电池中的量子效率损失和电压损失

聚3-己基噻吩(P3HT)以其合成工艺简单、成本低廉的优势,成为有机光伏领域中最具吸引力的电子给体材料之一。然而,目前P3HT: 非富勒烯太阳能电池的光伏性能仍然较差。在本工作中,我们证明了与P3HT: 富勒烯太阳能电池相比,较快的电荷转移态的非辐射衰减速率(K_nr)是导致P3HT: 非富勒烯太阳能电池中较低的量子效率和较高的电压损失的原因。然后,我们研究了基于非富勒烯受体ZY-4Cl的太阳能电池的工作机理。研究结果表明与P3HT: 非富勒烯体系相比,P3HT: ZY-4Cl中K_nr的降低改善了器件的量子效率,同时降低了电压损失。K_nr降低的原因可以部分归因于电荷转移态能量的增加。此外,给体分子和受体分子之间的距离(DA间距)的增大也是K_nr减少的重要原因。因此,我们得出结论：为了提高P3HT太阳能电池的性能,需进一步降低器件的K_nr,这可通过增加活性层中的DA间距来实现。     

Direct electrochemical nanopatterning of polycarbazole monomer and precursor polymer films: ambient formation of thermally stable conducting nanopatterns

The direct nanopatterning of polycarbazole on ultrathin films of a "precursor polymer" and monomer under ambient conditions is reported. In contrast to previous reports on electrochemical dip-pen nanolithography using monomer ink or electrolyte-saturated films in electrostatic nanolithography, these features were directly patterned on spin-cast films of carbazole monomer and poly(vinylcarbazole) (PVK) under room temperature and humidity conditions. Using a voltage-biased atomic force microscope (AFM) tip, electric-field-induced polymerization and cross-linking occurred with nanopatterning in these films. Different parameters, including writing speed and bias voltages, were studied to demonstrate line width and patterning geometry control. The conducting property (current-voltage (I-V) curves) of these nanopatterns was also investigated using a conducting-AFM (C-AFM) setup, and the thermal stability of the patterns was evaluated by annealing the polymer/monomer film above the glass transition (T(g)) temperature of the precursor polymer. To the best of our knowledge, this is the first report in which thermally stable conducting nanopatterns were drawn directly on monomer or polymer film substrates using an electrochemical nanolithography technique under ambient conditions.     

光敏层厚度与退火温度调控对聚3-己基噻吩光电探测器性能的影响

以聚3-己基噻吩(P3HT)为给体材料,富勒烯衍生物(PC61BM)为受体材料,制备了一系列结构为ITO/PEDOT:PSS/P3HT:PC61BM/C60/Al的体异质结光电探测器.研究了120、160、180与200 nm不同光敏层厚度,100、120、130、140与150℃不同退火温度等条件对器件性能的影响,并采用原子力显微镜(AFM)对光敏层形貌进行了分析.研究发现,基于180 nm厚光敏层、150℃退火处理的器件,在-2 V的偏压下550 nm处有最大响应度,为268 mA/W,并且在470~610 nm范围内响应度都超过了200 mA/W;基于180 nm厚光敏层、120℃退火处理的器件有最大线性动态范围,为95 dB.研究表明,适当厚度的光敏层有利于提高光吸收效率与器件的光伏性能;退火处理,可以使光敏层形成均匀的互穿网络结构,进而减小空穴与电子的复合概率,提高器件的光伏性能.     

喷涂法制备大面积倒置聚合物光伏器件

采用喷涂工艺制备了结构为ITO/ZnO/P3HT∶PCBM/V2O5/Ag(P3HT:聚噻吩;PCBM:6,6-苯基-C61-丁酸甲酯)的大面积倒置光伏器件,有效面积为1.0×1.1 cm2。 光谱测试结果表明,退火处理后,P3HT∶PCBM薄膜吸收显著增强,并且产生一定程度的红移。 采用ZnO和V2O5代替LiF和PEDOT∶PSS(聚(3,4-乙撑二氧噻吩)∶聚苯乙烯磺酸盐)作为器件修饰层,避免了PEDOT∶PSS对ITO的腐蚀和LiF潮解,采用Ag代替Al作为金属背电极避免了Al被氧化。 经过后退火处理器件的效率从1.1%提升至1.65%。 器件的稳定性相对于传统结构有了大幅提升,8周后器件效率只衰减10%。     

用CdSe/ZnS量子点提高体异质结有机太阳电池的效率

通过掺杂吸收光谱在可见光波段的量子点可提高聚合物对可见光的吸收,因此掺杂CdSe/ZnS核-壳结构量子点(CQDs)能提高聚(3-己基噻吩):[6,6]-苯基-C61-丁酸甲酯(P3HT:PCBM)体异质结太阳电池的能量转换效率.本文研究了CdSe/ZnS量子点在P3HT:PCBM中的不同掺杂比例及其表面配体对太阳电池光伏性能的影响,优化器件ITO(氧化铟锡)/PEDOT:PSS(聚(3,4-乙撑二氧噻吩:聚苯乙烯磺酸)/P3HT:PCBM:(CdSe/ZnS)/Al的能量转换效率达到了3.99%,与相同条件下没有掺杂量子点的参考器件ITO/PEDOT:PSS/P3HT:PCBM/Al相比,其能量转换效率提高了45.1%.     

Vertical phase separation of conjugated polymer and fullerene bulk heterojunction films induced by high pressure carbon dioxide treatment at ambient temperature

The morphology of bulk-heterojunctions (BHJ) is critically important for conjugated polymer and fullerene blend solar cells. To alter the morphology, high pressure (gas phase) carbon dioxide (CO(2)) treatment is applied to poly(3-hexyl thiophene) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) blend films under ambient temperature. This process can achieve vertically phase separated morphology such that PCBM distributes toward the film surface, which is suggested by secondary ion mass spectroscopy (SIMS), contact angle, X-ray photoelectron spectroscopy (XPS) and cross-sectional scanning electron microscope (SEM) studies. While pristine P3HT films do not show a significant change upon CO(2) treatment, pristine PCBM films are plasticized in high pressure CO(2). Thus, PCBM is selectively plasticized by CO(2) in the blend film and is drawn towards the surface due to depressed surface energy, although P3HT tends to distribute around the surface without CO(2). This stratification process can enhance solar cell performance. 55% improvement is achieved in the power conversion efficiency of the CO(2) treated device compared to the untreated one, indicating that CO(2) treatment can be a good candidate for optimizing the morphology and enhancing the performance of BHJ polymer solar cells.     

碘化铅作为空穴传输层在P3HT:PC61BM聚合物太阳能电池中的增强效果

开发了一类新型阳极界面缓冲材料PbI₂,制备了结构为ITO/PbI₂/P3HT:PC₆₁BM/Al(氧化铟锡导电玻璃/碘化铅/聚三已基噻吩:富勒烯衍生物/铝)的器件,制备工艺包括旋涂和蒸镀,考察了PbI₂在聚合物太阳能电池原型器件ITO/P3HT:PC₆₁BM/Al中的效果。不同碘化铅浓度,退火温度,退火时间,对PbI₂薄膜的质量都会有影响。很显然,高质量的PbI₂薄膜将会带来好的光电转化效率。PbI₂薄膜的透光性,结晶性,以及表面形貌可以用来描述所成薄膜的质量好坏。对能带来最好性能的碘化铅薄膜进行了紫外-可见光谱,X射线粉末衍射(XRD),原子力显微镜(AFM),扫描电子显微镜(SEM)等表征。实验发现,太阳能电池器件的效率对PbI₂浓度比较敏感,最优化的条件为,旋涂浓度为3 mg·mL^-1,100 ℃退火30 min,其电池的开路电压(V_oc)达到0.45 V,短路电流密度(J_sc)为7.9 mA·cm^-2,填充因子(FF)为0.46,与没有界面缓冲材料的器件相比,光电转换效率(PCE)由0.85%提高到1.64%。     

Comparing spiro-OMeTAD and P3HT hole conductors in efficient solid state dye-sensitized solar cells

Two hole conductor materials, spiro-OMeTAD and P3HT, were compared in solid-state dye-sensitized solar cells. Two organic dyes containing one anchor unit (D35) or two anchor units (M3) were used in the comparison. Absorbed photon to current conversion efficiency close to unity was obtained for the devices with spiro-OMeTAD. Energy conversion efficiencies of 4.7% and 4.9% were measured for the devices with spiro-OMeTAD and the dyes D35 and M3, respectively. For the devices using the P3HT hole conductor the results were rather different comparing the two dye molecules, with energy conversion efficiencies of 3.2% and 0.5% for D35 and M3, respectively. Photo-induced absorption measurements suggest that the regeneration of the dyes, and the polymer infiltration, is not complete using P3HT, while spiro-OMeTAD regenerates the dyes efficiently. However, the TiO(2)/D35/P3HT system shows rather high energy conversion efficiency and electrochemical oxidation of the dyes on TiO(2) indicates that D35 have a more efficient dye to dye hole conduction than M3, which thereby might explain the higher performance. The dye hole conduction may therefore be of significant importance for optimizing the energy conversion in such hybrid TiO(2)/dye/polymer systems.     

Correlating interface heterostructure, charge recombination, and device efficiency of poly(3-hexyl thiophene)/TiO2 nanorod solar cell

The charge recombination rate in poly(3-hexyl thiophene)/TiO(2) nanorod solar cells is demonstrated to correlate to the morphology of the bulk heterojunction (BHJ) and the interfacial properties between poly(3-hexyl thiophene) (P3HT) and TiO(2). The recombination resistance is obtained in P3HT/TiO(2) nanorod devices by impedance spectroscopy. Surface morphology and phase separation of the bulk heterojunction are characterized by atomic force microscopy (AFM). The surface charge of bulk heterojunction is investigated by Kelvin probe force microscopy (KPFM). Lower charge recombination rate and lifetime have been observed for the charge carriers in appropriate heterostructures of hybrid P3HT/TiO(2) nanorod processed via high boiling point solvent and made of high molecular weight P3HT. Additionally, through surface modification on TiO(2) nan,orod, decreased recombination rate and longer charge carrier lifetime are obtained owing to creation of a barrier between the donor phases (P3HT) and the acceptor phases (TiO(2)). The effect of the film morphology of hybrid and interfacial properties on charge carrier recombination finally leads to different outcome of photovoltaic I-V characteristics. The BHJ fabricated from dye-modified TiO(2) blended with P3HT exhibits 2.6 times increase in power conversion efficiency due to the decrease of recombination rate by almost 2 orders of magnitude as compared with the BHJ made with unmodified TiO(2). In addition, the interface heterostructure, charge lifetime, and device efficiency of P3HT/TiO(2) nanorod solar cells are correlated.     

Gold nanoparticle patterning of silicon wafers using chemical e-beam lithography

This paper demonstrates a novel facile method for fabrication of patterned arrays of gold nanoparticles on Si/SiO2 by combining electron beam lithography and self-assembly techniques. Our strategy is to use direct-write electron beam patterning to convert nitro functionality in self-assembled monolayers of 3-(4-nitrophenoxy)-propyltrimethoxysilane to amino functionality, forming chemically well-defined surface architectures on the 100 nm scale. These nanopatterns are employed to guide the assembly of citrate-passivated gold nanoparticles according to their different affinities for amino and nitro groups. This kind of nanoparticle assembly offers an attractive new option for nanoparticle patterning a silicon surface, as relevant, for example, to biosensors, electronics, and optical devices.     

Improved efficiency of photovoltaics based on CdSe nanorods and poly(3-hexylthiophene) nanofibers

We present photovoltaic devices based on a blend of the conjugated polymer poly(3-hexylthiophene) (P3HT) with cadmium selenide nanorods, where the solvent for film deposition has been carefully chosen to optimize the film morphology. Using 1,2,4-trichlorobenzene (TCB), which has a high boiling point, as solvent for P3HT it is possible to obtain a fibrilar morphology, providing extended pathways for hole transport. Blend devices fabricated using this solvent gave solar power conversion efficiencies of 2.6%. This indicates that efficient transport of electrons and holes is achieved in these films, allowing them to operate effectively at solar illumination intensities.     

P3HT修饰一维有序壳核式CdS/ZnO纳米棒阵列复合膜的光电化学性能

采用电化学方法在铟锡氧化物(ITO)导电玻璃上制备了高度有序的ZnO纳米棒阵列, 在ZnO纳米棒阵列上先后电化学沉积CdS纳米晶膜及聚3-己基噻吩(P3HT)薄膜得到P3HT修饰的一维有序壳核式CdS/ZnO纳米阵列结构, 并通过扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、能量散射X射线(EDX)等表征手段证实了该结构的形成. 以此纳米结构薄膜为光阳极组装新型半导体敏化太阳电池, 研究了CdS纳米晶膜的厚度和P3HT薄膜的沉积对电池光伏性能的影响, 初步探讨了电荷在电池结构中的传输机理, 结果表明, CdS纳米晶膜和P3HT薄膜的沉积有效地拓宽了光阳极的光吸收范围, 实验中电池的光电转换效率最高达到1.08%.     

New strategy for enhancing performance of P3HT-based organic field-effect transistor via regulating the precipitated speed of solute in volatile solvents

In this work, a new strategy is proposed to improve the performance of poly (3-hexylthiophene-2,5-diyl) (P3HT) based organic field-effect transistor (OFET). The high orientation of P3HT chain is obtained via utilizing precipitation characteristics of P3HT in volatile CH₂Cl₂ with the temperature decrease of solution in the hot spin-coating process. Meanwhile, a small amount of 1,2-dichlorobenzene (ODCB) with high boiling point is introduced into CH₂Cl₂ to make the inner part of the film stay in liquid state for a long time, and prolong the self-organization time of P3HT chain. Compared with control device prepared in pure CH₂Cl₂, the mobility of optimized device obtained by using blended solvent increases about 20-fold, the on/off ratio enhances about three orders of magnitude, and the operation time window of spin-coating up to 30 min (control device < 30 s). With this new strategy, the film quality can be easily controlled, which provides a new method for preparation of high-performance polymer optoelectronic devices.     

Directed electron transfer in Langmuir-Schäfer layers of porphyrin-fullerene and phthalocyanine-fullerene dyads in inverted organic solar cells

In this study double linked porphyrin-fullerene and phthalocyanine-fullerene dyads and a single linked phthalocyanine-fullerene dyad were studied as components in inverted organic solar cells (OSCs) equipped with the well known P3HT:PCBM bulk heterojunction as the photoactive layer. The dyad monolayers were deposited onto a surface of P3HT:PCBM by using the Langmuir-Sch?fer method, therefore forming oriented monolayers in which the electron donor (D) and the acceptor (A) exist as a close proximity pair in a 1:1 molar ratio. As a result of this structure short circuit current density (J(sc)), open circuit voltage (V(oc)), and power conversion efficiency (η) increased, while the fill factor (FF) remained the same. The devices which contained dyads with double linkage produced higher efficiencies than the one with a single linked dyad. This result can be explained in terms of molecular orientation. It was also verified that the prepared OSC devices have promising long term air stability.