2,3-Dihydroxypyridine Loaded Amberlite XAD-2 (AXAD-2-DHP): Preparation, Sorption–Desorption Equilibria with Metal Ions, and Applications in Quantitative Metal Ion Enrichment from Water, Milk and Vitamin Samples

2,3-Dihydroxypyridine loaded (via –N=N–linker) Amberlite XAD-2 (AXAD-2-DHP) was prepared and characterized by elemental analyses, TGA and FT-IR spectra. It (1g packed in a column of 1cm diameter; surface area 135.5m²g^–1) was found to be an effective solid phase sorbent for enriching Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺ at pH 3.5 to 7.0 using flow rates between 1.0–5.0mLmin^–1. For desorption (recovery 97.0–99.8%) of the metal ions, 8 to 10mL of 2.0molL^–1 HCl or 1.5molL^–1 HNO₃ at a flow rate of between 2.0 and 4.0mLmin^–1 were found most suitable. The t_1/2 (time for 50% sorption) is between 2 and 10min when a 50mL solution (containing a total amount of metal of 2mg) was equilibrated with 0.5g of resin. Sorption of all metal ions except Pb²⁺ follows the Langmuir model, whereas for Pb the data fits with the Freundlich model. The sorption capacity is between 60.7 (for Cd) and 406.7 (for Cu) µmolg^–1. The resin can withstand an acid concentration of 6molL^–1 and can be reused for thirty cycles of sorption–desorption. The preconcentration factor varies between 100 and 300. For Cd, Ni and Cu the sorption capacity of 2,3-dihydroxypyridine loaded cellulose is lower than that of the present resin. The tolerance limits of electrolytes, humic acid, complexing agents, Ca²⁺ and Mg²⁺ in the enrichment of all metal ions are reported. The limits of detection are 3.88, 5.37, 8.72, 13.88, 4.71, 1.24, 0.59 and 0.30µgL^–1 for Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺, respectively. The calibration curves for flame AAS determination were linear in the ranges 0.018–1.0, 0.067–5.0, 0.2–5.0, 0.9–20, 0.028–2.0, 0.077–5.0, 0.19–10 and 0.1–3.5µgmL^–1, respectively. All the eight metal ions in river and synthetic water samples, Co in vitamin tablets and Zn in milk samples have been quantitatively enriched with Amberlite XAD-2-DHP and determined by flame atomic absorption spectrometry.     

Polarographic Determination of Lovastatin in the Presence of H2O2 in Pharmaceuticals, Human Urine and Serum

The polarographic reduction and catalytic behavior of lovastatin are studied by polarography and cyclic voltammetry. The reduction wave of lovastatin appears at ca. –1.49V (vs. SCE) in 0.16molL^–1 Na₂B₄O₇–KH₂PO₄ (pH=7.4) supporting electrolyte containing 20% ethanol. It is ascribed to a 2e^–, 2H⁺ addition to the carbonyl group on lactone ring. If H₂O₂ is present, the reduction wave is catalyzed to produce a polarographic catalytic wave. Based on the catalytic wave, a novel method for the determination of lovastatin is proposed. A rectilinear calibration curve of the catalytic wave was obtained for lovastatin concentration in the range 1.5×10^–8 to 1.0×10^–6molL^–1. The peak current of the catalytic wave is ca. 12 times higher than that of the corresponding reduction wave. The detection limit is 8.0×10^–9molL^–1. The proposed method is simpler, faster and more sensitive than the known methods for lovastatin analysis, and can be applied to the direct determination of lovastatin in pharmaceuticals, urine and serum without preliminary separation.     

ET-AAS in the Analysis of high-purity mercury

ET-AAS is investigated for the analysis of high purity mercury. Two possibilities are proposed: ET-AAS determination of trace analytes in the presence of high mercury concentrations or after matrix separation by reduction. The ET-AAS analysis of high-purity mercury under optimal instrumental parameters permits fast and reproducible determination of 0.03 gg^–1 Al, Cd and Mn; 0.05 gg^–1 Cu, Co, Cr, Fe, Ni and Pb and 0.2 gg^–1 V. Preliminary mercury matrix reductive separation with ascorbic acid allows determination of 0.005 gg^–1 Cd, 0.02 gg^–1 Cu, Cr and Mn, 0.03 g g^–1 Co, Ni and Pb, 0.05 g g^–1 Al and Fe and 0.1 gg^–1 V, but the reproducibility is lower. The main advantage of the second procedure is that it avoids laboratory and instrument pollution with toxic mercury.     

Diacetylenic Derivatives of Fe2(CO)6(μ-EE′): Spectroscopic Investigations of Fe2(CO)6{μ-EC(H) = C(C≡ CMe)E′} (E = E′, E ≠ E′; E, E′ = S, Se, Te)

The diacetylenic adducts, Fe₂(CO)₆{-EC(H) = C(C CMe)E} (E = E, E E; E, E = S, Se, Te) (1–8) have been obtained from the room temperature stirring of Fe₂(CO)₆(-EE) with HC CC CMe in methanol solvent containing sodium acetate. Compounds 1–8 have been characterized by IR and multinuclear NMR (¹H, ¹³C, ⁷⁷Se, and ^l25Te) spectroscopy. Trends in the chemical shifts of ⁷⁷Se and ¹²⁵Te NMR spectra of Fe₂(CO)₆{-EC(H) = C(C CMe)E} with a variation of EE are discussed.     

Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Studies on the Complexes of N,N′-Bis[o-(diphenylphosphino)benzylidene]ethylenediamine with Transition Metal Ions

The thermodynamic parameters for the interaction of Cu²⁺, Ni²⁺, Co²⁺, Cd²⁺, andAg⁺ with the new title ligand have been determined by titration calorimetry in 50% THF–methanol (V/V) at 25 °C.Ag⁺ exhibited remarkably higher complexation selectivity.Ag⁺ and several transition metal ions have been transportedusing this ligand as carrier in a bulk liquid membrane. CompetitiveAg⁺–M²⁺ transport studies have also beencarried out for the same system. In this membrane transport study, high transport of Ag⁺ was observed in both single and competitiveAg⁺–M²⁺ transport studies. The complexformation of N,N-bis[o-(diphenylphosphino)benzylidene]ethylenediamine (P₂N₂) with silver,[Ag(P₂N₂)] (NO₃), (1) is reported. Complex 1 has been characterized by X-ray crystallography. 1 ismonoclinic, space group P2_1/n (No. 14), with cell dimensionsa = 13.398(4) , b=12.577(5) , c = 21.521(4) , =100.14(2) , V = 3570(2) ³ and Z = 4.     

Instrumental neutron activation analysis of carbon containing micro-spheres from Jungfrau-Joch glacier ice

From about 700 kg old, high altitude glacier ice (age 400 y) more than 170 glassy spherical objects with a mean diameter of 100 m were isolated. Neutron activation analysis of individual transparent objects (each 10^–6 g) showed the presence of K, Sc, Cr, Fe, La, Eu, Au, etc., in varying concentrations. A detection limit of 10^–14 g/g was achieved by means of an anticompton circuit. A systematic study by mass spectrometry of positive and negative ions using a LASER microprobe disclosed that the main constituents of some of these smooth glacier spheres consisted of elemental carbon. The chemical composition of some spherules admits the possibility of extraterrestrial origin, e.g. ablation material from meteorites with high carbon contents, which entered the earth's atmosphere.     

Genetic Algorithm Applied to the Selection of Conditions for the Simultaneous Quantification of Three-Food Colorants Using a Hand Scanner

A low-cost and reliable method employing a hand scanner for simultaneous colorimetric quantification of food colorant mixtures including amaranth, brilliant blue, and tartrazine is presented. Compared to a spectrophotometer, a hand scanner is inexpensive, available in most work offices, and easier to operate by non-skilled users. The appropriate instrumental conditions for measuring were selected using a genetic algorithm (GA) coupled with partial least square (PLS) regression. Using the conditions selected by GA, PLS and multiple linear regression (MLR) were compared, and similar results for the two methods were obtained. Under the selected conditions for each of the colorants, artificial neural network (ANN) including three layers of nodes and a Levenberg-Marquardt learning rule was employed, which improved the results. The concentration ranges for the three colorants in the multivariate calibration models were 0.00–5.31mmolL^–1 for amaranth, 0.00–1.85mmolL^–1 for brilliant blue, and 0.00–21.57mmolL^–1 for tartrazine. The minimum estimated relative standard error percentages (RSE%) for prediction of analytes in synthetic samples, using ANN with optimized parameters, were 16.8% for amaranth, 4.8% for brilliant blue, and 5.6% for tartrazine. A number of commercial food products were analyzed satisfactorily with the proposed method.     

Kinetic Spectrophotometric Determination of Total Iron in Natural Water by Flow Injection Analysis Using On-Line Preconcentration

A new flow injection catalytic spectrophotometric method for on-line preconcentration and determination of total iron in natural water is described. The method is based on a combination of iron-catalyzed oxidation of diaminoditolyl by potassium bromate and the use of on-line preconcentration of iron onto 8-hydroxy-quinoline immobilized on silica gel. The corresponding calibration graph is linear over the range of 2.0–110ngmL^–1 for Fe(III) using a time-based technique for 5min preconcentration. The relative standard deviation of 11 measurements of 60ngmL^–1 Fe(III) was 0.67%. The method was applied to the determination of iron in natural water. The results obtained by the proposed method were compared with those obtained by ICP-AES. The t-test showed no significant differences between the two methods at a confidence level of 95%.     

Electrochemical Behavior of Epinephrine at a Penicillamine Self-Assembled Gold Electrode,and its Analytical Application

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The self-assembled electrode shows obvious electrocatalytic activity for the oxidation of epinephrine (EP). In phosphate buffer (pH 7.73), a sensitive oxidation peak was observed at 0.190V with the PCA modified Au electrode. The peak current is proportional to the concentration of EP in the range of 2.0×10^–56.0×10^–4molL^–1 and 5.0×10^–6 2.0×10^–4molL^–1 for cyclic voltammetry (CV) and differential pulse voltammetry (DPV) with the detection limits of 1.8×10^–7 and 1.3×10^–7molL^–1, respectively. The possible reaction mechanism is also discussed. The PCA self-assembled monolayer modified gold electrode is highly stable and can be applied to the determination of EP in practical injection samples. Application is simple, rapid and produces accurate results.     

Simultaneous Determination of Pioglitazone and Glimepiride by High-Performance Liquid Chromatography

A rapid and accurate HPLC method has been developed for simultaneous determination of pioglitazone and glimepiride. Chromatographic separation of the two pharmaceuticals was performed on a Cosmosil C₁₈ column (150 mm × 4.6 mm, 5 m) with a 45:35:20 (v/v) mixture of 0.01 m triammonium citrate (pH adjusted to 6.95 with orthophosphoric acid), acetonitrile, and methanol as mobile phase, at a flow rate of 1.0 mL min^–1, and detection at 228 nm. Separation was complete in less than 10 min. The method was validated for linearity, accuracy, precision, limit of quantitation, and robustness [1, 2]. Linearity, accuracy, and precision were found to be acceptable over the ranges 2.50–30.00 g mL^–1 for pioglitazone and 0.10–10.00 g mL^–1 for glimepiride.     

Gamma radiolysis of Methyl Red solution and reaction induced by γ-irradiated NaCl in Methyl Red

The -radiolysis of Methyl Red solution in HCl medium at pH=2 has been studied along with energy transfer reaction brought about byF and hole centers of -irradiated NaCl. The G-values for degradation of the azo dye indicator by radiolysis and -irradiated salt were determined as 9·10^–1 and 4.8·10^–3, respectively. The kinetic rate constants (k) of degradation are evaluated as 2·10^–5 rad^–1 in the case of direct radiolysis, while for the irradiated salt it is 2·10^–7 rad^–1. The extent of degradation by direct -radiolysis is 100–200 times greater as compared to that by the -irradiated salt. The same mechanism is proposed for radiolysis as well as the reaction induced by -irradiated sodium chloride.     

1H-NMR-spektroskopische Analyse von 2-Chlor-1.3.2-dioxarsolan

The¹H-NMR-spectral data of 2-chloro-1.3.2-dioxarsolane are presented and discussed. The protons of the methylene groups form in concentrated solutions by rapide chlorine exchange anAAAA spin system. In dilute solutions the protons form anAABB spin system, which is changed to anAAAA system by addition of chlorine ions.The vicinal H–C–C–H-coupling constants indicate a twist-envelope conformation.

---

---

Mit 1 Abbildung     

Electrochemical Determination of Ascorbic Acid at γ-MnO<Subscript>2</Subscript> Modified Carbon Black Microelectrodes

A carbon black microelectrode modified by -MnO₂ has been prepared. The electrocatalytical oxidation of ascorbic acid (AA) at this microelectrode was investigated. The 2nd-order linear scan voltammograms of AA are recorded from –0.5 to 0.5V (vs. SCE). The relationship between the oxidation peak current of AA and its concentration in the range of 1.0×10^–64.0×10^–3molL^–1 is linear. The detection limit (3) was found to be 6.0×10^–7molL^–1. Also, the determination of AA in samples is evaluated, and the results are satisfactory.     

Transformed steroids. 161. Reactivity of 17-spirooxetane-20-ketosteroids towards opening of the four-membered ring

Conclusions Replacement of the 20-oxo group in 17,21-epoxypregn-5-en-3-ol-20-one by the hydrazono-group affects the cleavage of the oxetane ring by thiocyanic acid, reaction occurring preferentially by introduction of^–NCS at C¹⁷ with consequent expansion of the four-membered ring to a six-membered ring with the formation of the [17; 21]-1,3-tetrahydrooxazine-2-thione.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 6, pp. 1393–1396, June, 1987.     

Triterpene glycosides of Astragalus and their genins XXXIX. Cycloaraloside D from Astragalus amarus

The structure of a triterpene glycoside of the cycloartane series — cycloaraloside D, isolated from the roots ofAstragalus amarus Pall. (Leguminosae) — has been established on the basis of chemical transformations and spectral characteristics. Cycloaraloside D is 20R, 24S-epoxycycloartane-3, 6, 16, 25-tetraol 3-0-[0--L-rhamnopyranosyl-(1 2)--D-glucopyranoside].Institute of Chemistry of Plant Substances, Academy of Sciences of the Uzbek SSR, Tashkent. Translated from Khimiya Prirodnykh Soedinenii, No. 4, pp. 526–528, July–August, 1991.     

Electrochemical Properties and Analytical Applications of Keggin-type Phosphomolybdic Anions in Electrostatically Linked 2-Aminoethanethiol Self-Assembled Monolayers

A composite film containing a heteropolyanion was prepared on a 2-aminoethanethiol (AT) self-assembled monolayer film-modified gold electrode by attaching the Keggin-type phosphomolybdic anion. The surface structures and electrochemical properties of the composite films were characterized by using ATR-FTIR, AC impedance, cyclic voltammetry and chronocoulometry. FTIR studies indicated that there was some electrostatic interaction between Pmo₁₂O₄₂^7– and surface NH₃⁺. Three reversible redox couples were observed in 1.0molL^–1 H₂SO₄ in the potential range of 0–0.7V for the composite film modified electrode, which were attributed to two-electron and two-proton electrochemical processes of PMo₁₂O₄₂^7–. The diffusion coefficient is determined to be 2.04×10^–7cm²s^–1. The composite film shows good catalytic activities for the reduction of nitrite (NO₂^–) in acidic solution and the catalytic mechanisms are described. The modified electrode provides a linear response for NO₂^– in the concentration range of 1.0×10^–4 to 1.0×10^–7molL^–1 by differential pulse adsorptive stripping voltammetry with a correlation coefficient of 0.9965. The detection limit (three times the signal blank/slope) was 2.0×10^–8molL^–1. The modified electrode was used for the determination of NO₂^– in wastewater.     

An investigation of the aggregation and water-air interfacial behaviour of a cationic tentacle molecule

The aggregation and air-water interface properties of a three-legged tentacle molecule tris (11-pyridinium undec-1-yl)benzene-1, 3, 5-tricarboxylate tribromide have been investigated by measurement of the molar conductance, , and equilibrium surface tensin,, over a wide range of bulk concentration (8×10^–6 – 0.3 M). In contrast to the single chain analogue, dodecyl pyridinium bromide, DDPB, the tentacle species shows no evidence for a conventional micellar transition in solutions up to 100 fold more concentrated than the critical micelle concentration of DDPB, though aggregation of small numbers of molecules cannot be excluded. The conductance behaviour suggests the occurrence of ion-pair (or higher) equilibria, which are likely to complicate the interpretation of the data. Also, in contrast to a previous tentacle molecule described in the literature, the present species is significantly surface active, and in the high concentration limit reduces to <30 mNm^–1, significantly lower than the values obtained for simple ionic amphiphiles. In this region the tentacle species seems to stand like a tripod at the water-air interface with both its hydrocarbon legs and its aromatic body lifted clear of the water surface. At much lower concentrations two small plateau regions in are apparent ( 60 and 52 mNm^–1). Here, the tentacle molecule occupies a much larger surface area, and seems to adopt a crab-like crouch with its aromatic body and polar ester substituents lowered into the water surface.     

Low-temperaturic template synthesis of macrocyclic cobalt(III) chelates with (N,N,S,S)-donor atomic ligands in the cobalt(II)–dithiooxamide-formaldehyde and cobalt(II)–dithiooxamide-glyoxal systems in the Co2[Fe(CN)6]-gelatin-immobilized matrices

The complexing processes in the triple cobalt(II)–dithiooxamide-formaldehyde and cobalt(II)–dithiooxamide-glyoxal systems taking place in the cobalt(II)hexacyanoferrate(II) gelatin-immobilized matrix in contact with aqueous alkaline solutions (pH ca. 12) containing (dithiooxamide+formaldehyde) and (dithiooxamide+glyoxal), have been studied. Template synthesis leading to macrocyclic coordination compounds with tetradentate N,N,S,S-donor ligands-(2,8-dithio-3,7-diaza-5-oxanonan-dithioamide-1,9) and (2,7-dithio-3,6-diazaoctadien-3,5-dithioamide-1,8) with Co^II–Co^III redox-process occurs under these specific conditions where dithiooxamide, formaldehyde and glyoxal are the ligand synthons.     

Formation of N-butane in the pyrolysis of ethylene [1]

Yields of n-C₄H₁₀ have been measured from the flow pyrolysis of C₂H₄ at 897 (±7) K. From 77 to 720 Torr the order of n-C₄H₁₀ formation was found to be 2.0±0.3 The rate constant for the reaction, was estimated to be 2.4(±0.6)×10^–4l mol^–1s^–1.

---

-C₄H₁₀ C₂H₄ 897 (±7) . -C₄H₁₀ 77 720 2.0±0.3. 2C₂H₄C₂H₃+C₂H₅ 2,4 (±0,6)×10^{–4 –1–1}.