Microstructure and electromagnetic characteristics of BaTiO3/Ni hybrid particles prepared by electroless plating

To improve the microwave absorption ability, hybrid particles containing both dielectric loss of BaTiO₃ and magnetic loss of Ni were fabricated via electroless Ni plating on BaTiO₃ particles. A continuous Ni coating was successfully covered on the surface of the BaTiO₃. The effect of the Ni content on complex permittivity, complex permeability, and microwave absorption properties of BaTiO₃/Ni hybrid particles was investigated. The real (?′) and imaginary (?″) parts of complex permittivity as well as imaginary part of complex permeability (μ″) were found to increase with an increase in Ni content, while the variation of the real part of complex permeability (μ′) with Ni content was non-linear. The microwave absorption performances could readily be tuned base on the changing Ni content of the hybrid particles. The optimal absorption performances were attained when the content of Ni reached 38.9 wt% in hybrid particles.     

Magnetic and microwave absorbing properties of polyaniline/γ-Fe2O3 nanocomposite

The conducting protonated polyaniline (ES)/γ-Fe₂O₃ nanocomposite with the different γ-Fe₂O₃ content were synthesized by in-situ polymerization. Its morphology, microstructure, DC conductivity and magnetic properties of samples were characterized by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), four-wire-technique, and vibrating sample magnetometer (VSM), respectively. The microwave absorbing properties of the nanocomposite powders dispersing in wax coating with the coating thickness of 2 mm were investigated using a vector network analyzers in the frequency range of 7–18 GHz. The pure ES has shown the absorption band with a maximum absorption at approximately 16 GHz and a width (defined as frequency difference between points where the absorption is more than 8 dB) of 3.24 GHz, when 10% γ-Fe₂O₃ by weight is incorporated , the width is broadened to 4.13 GHz and some other absorption bands appear in the range of 7–13 GHz. The parameter dielectric loss tan δ_e (=ε″/ε′) in the 7–18 GHz is found to decrease with increasing γ-Fe₂O₃ contents with 10%, 20%, 30%, respectively, but magnetic loss tan δ_m (=μ″/μ′) increases with increasing γ-Fe₂O₃ contents. The results show that moderate content of γ-Fe₂O₃ nanoparticles embedded in protonated polyaniline matrix may create advanced microwave absorption properties due to simultaneous adjusting of dielectric loss and magnetic loss.     

Microwave absorption properties of 50% SrFe12O19–50% TiO2 nanocomposites with porosity

SrFe₁₂O₁₉–TiO₂ nanocomposites are usually used for absorbing microwaves in military and civil applications. In this work, microwave absorption properties of porous SrFe₁₂O₁₉ nanocomposites with 50% weight ratio of TiO₂ have been investigated. 50% TiO₂–50% SrFe₁₂O₁₉ nanocomposites were prepared by a controlled hydrolysis of titanium tetraisopropoxide in which SrFe₁₂O₁₉ nanoparticles were synthesized by a sol–gel auto combustion route. The morphology, crystalline structure and crystallite size of SrFe₁₂O₁₉–TiO₂ nanocomposites were characterized by field emission scanning electron microscopy and X-ray powder diffraction. The magnetic measurements were carried out with a vibrating sample magnetometer. The microwave absorption was measured by a Vector Network Analyzer. The microwave absorption results indicated that the reflection losses for specimens with 52%–56% porosity and thicknesses of 1.8, 2.1 and 2.6 mm were not very low but minimum reflection loss for a specimen with 4.2 mm thickness reached upto −33 dB.     

Periodic microwave absorption in superconducting whiskers

The microwave absorption and structural studies of BiSrCaCuO (2212) whiskers have been performed. The low-angle boundaries in the (a, b) and (a, c) planes have been observed. The periodic microwave absorption signal indicated the flux quantization in a system of weak links and superconducting loops formed on the boundaries. Regular character of this signal suggests possible applications in SQUID magnetometry. Lower Josephson critical fieldH _clJ=1.6 Oe and the critical temperatureT _c=89 K have been determined. The Josephson penetration depth was estimated from the Ginzgurg-Landau, and Clem models.     

Microwave studies of Bi(2212) HTSC single crystals at nitrogen temperatures

Absorption of microwave power by single-phase Bi(2212) crystals with a broad (15 K) phase transition has been studied. A temperature-localized drop of microwave power absorption at the beginning of the superconducting transition at 80 K has been established. A possible mechanism of this absorption feature based on the concept of synchronization of Josephson junctions near T _c is discussed.     

A superior microwave absorption material: Ni2+-Zr4+ Co-Doped barium ferrite ceramics with large reflection loss and broad bandwidth

Large reflection loss and wide bandwidth are significant targets, determining the microwave absorption ability. However, it is still a challenge to simultaneously satisfy the two conditions. As a multifunctional material, BaFe₁₂O₁₉ possess excellent electromagnetic properties in the microwave frequency band. Due to the natural resonance phenomenon of the material, BaFe₁₂O₁₉ can produce a large magnetic loss which correlates with Fe³⁺ content, and the microwave absorption characteristics of barium ferrite can be modulated by ion doping. As a typical magnetic metal, Ni coupled with high-valence state Zr⁴⁺ doping helps to produce double resonance peaks. In this work, Ni²⁺-Zr⁴⁺ co-doping M-type barium ferrites (BaFe_12-2xNi_xZr_xO₁₉, BNZFO-x, x = 0–0.8) were prepared conveniently by solid-state reaction method. Several necessary measurements to characterize its microwave absorption property have been operated such as morphology, magnetic performance and electromagnetic parameters. The results show that reflection loss and bandwidth can be simply tuned by tailoring Ni²⁺-Zr⁴⁺ content. The reflection loss peak drifts from 18 GHz to 9.76 GHz, which involves a half of the studied frequency range. The maximum reflection loss achieves −60.6 dB and the corresponding bandwidth over −10 dB is 7.68 GHz for BNZFO-0.6 ceramic with only 2.1 mm thickness. Thus, the doping of Ni²⁺-Zr⁴⁺ ion pairs is beneficial to improve the absorbing properties of the material, and the superior microwave absorption property may originate from its inner double natural resonance in micro-scale. The excellent microwave absorption properties suggest that BNZFO-x is a promising candidate applied for designing electromagnetic shielding devices.     

Effect of Ag substitution on the electromagnetic property and microwave absorption of LaMnO3

La_1−xAg_xMnO₃ perovskites with different doping Ag-content were prepared by the sol–gel method. The electromagnetic characteristics and microwave loss behavior of these ion-doped rare-earth manganites were studied in the 2–18 GHz frequency range. The microstructure and morphology of the samples were characterized by X-ray diffraction (XRD), and scanning electron microscopy (SEM) techniques. The complex permittivity spectra, the complex permeability spectra and microwave reflection loss were measured by a microwave vector network analyzer system. The XRD patterns show that the crystalline perovskite main phase ABO₃ is formed and impurity phases disappear when calcined at 1100 °C, and Ag metal as an impurity phase appears when excessive Ag⁺ is doped. The SEM image indicates that many of the La_0.85Ag_0.15MnO₃ particles are fiber-like or ellipsoidal. Magnetic loss and dielectric loss coexist and cooperate in microwave attenuation by moderate substitution of Ag⁺ for La³⁺. The microwave absorption property of the La_0.85Ag_0.15MnO₃ sample is enhanced with the bandwidth below −10 dB at about 6 GHz and the peak value of reflection loss is near −25.0 dB at the layer thickness of 2 mm.     

Microwave absorption in high-Tc superconductors studied by the EPR method

Dependences of the microwave absorption on temperature, magnetic field and microwave power obtained for the high-T _c superconductors are presented. Shape of the magnetically modulated microwave absorption, low-field phase diagram and overheating of the Josephson junction system induced by microwave irradiation are discussed. The model of the Josephson junction system interacting with microwaves has been used to explain the behavior of the high-T _c superconductors in low magnetic field.     

γ-MnO2/polyaniline composites: Preparation, characterization, and applications in microwave absorption

MnO₂/doped polyaniline (PANI) is prepared by an in situ polymerization method using γ-MnO₂ as the addition agent and hydrochloric acid as the doping agent. Products are characterized by FT-IR, UV-vis, XRD, and TEM. Conductivity, electromagnetic properties, and microwave absorption properties are first discussed on the basis of structural characterization. The as-prepared products of MnO₂/PANI are partially crystalline in nature and spherical in pattern with grain sizes of 50-70 nm. MnO₂ particles are successfully decorated with doped PANI. MnO₂/PANI displays moderate electric conduction, excellent dielectric losses, and microwave absorption capabilities. Compared to pure MnO₂, the dielectric and reflection loss properties of MnO₂/PANI composites exhibit significant improvements, with an effective absorption band at 5 GHz under −10 dB and maximum reflection loss of −21 dB at 13.56 GHz. Pure MnO₂ shows an effective absorption band of 3 GHz under −10 dB and a maximum reflection loss of −14.20 dB at 11.5 GHz. Thus, MnO₂/PANI composites are found to be a promising microwave absorption material.     

Investigation on spectral features of tungsten ions in PbO-Bi2O3-As2O3 glass matrix

Lead bismuth arsenate glasses mixed with different concentrations of WO₃ (ranging from 0 to 6.0 mol%) were synthesized. Differential thermal analysis (DTA), optical absorption, ESR and IR spectral studies have been carried out. The results of DTA have indicated that there is a gradual decrease in the resistance of the glass against devitrification with increase in the concentration of WO₃ upto 4.0 mol%.The optical absorption spectra of these glasses exhibited a relatively broad band peaking at about 880 nm identified due to d_xy→d_x²_−y² transition of W⁵⁺ ions; this band is observed to be more intense in the spectrum of glass containing 4.0 mol% of WO₃. Further, two prominent kinks attributed to ³P₀→¹S₀, ¹D₂ transitions of Bi³⁺ ions have also been located in the absorption spectra. The ESR spectra of these glasses recorded at room temperature exhibited an asymmetric signal at g_⊥∼1.71 and g_ll∼1.61. The intensity of the signal is observed to be maximal for the spectrum of the glass W₄. The quantitative analysis of optical absorption and ESR spectral studies have indicated that there is a maximum reduction of tungsten ions from W⁶⁺ state to W⁵⁺ state in the glass containing 4.0 mol% of WO₃. The IR spectral studies have indicated that there is a increasing degree of disorder in the glass network with increase in the concentration of WO₃ upto 4.0 mol%.     

Microwave characterization of Pb<Subscript>1−x</Subscript>Ca<Subscript>x</Subscript>Fe<Subscript>0.5</Subscript>Nb<Subscript>0.5</Subscript>O<Subscript>3</Subscript> multiferroics at X-band

The microwave characteristics of Pb_1?x Ca _x Fe_0.5Nb_0.5O₃ multiferroics (x = 0.0, 0.4, 0.45, 0.5, 0.55, 0.6), have been investigated as a function of frequency and substitution. The results depict ?13.99 dB reflection loss at 11.65 GHz in composition x = 0.6. Microwave absorption is enhanced with substitution of Ca²⁺ ions and undoped composition 0.0 behaves as electromagnetic shield. The model governing microwave absorption is discussed and different compositions for electromagnetic applications have been suggested.     

Synthesis and nonlinear optical characterization of SnO2 quantum dots

The present paper demonstrates the preparation and characterization of SnO₂ semiconductor quantum dots. Extremely small ∼1.1 and ∼1.4 nm SnO₂ samples were prepared by microwave assisted technique with a frequency of 2450 MHz. Based on XRD analysis, the phase, crystal structure and purity of the SnO₂ samples are determined. UV-vis measurements showed that, for the both size of SnO₂ samples, excitonic peaks are obtained at ∼238 and ∼245 nm corresponding to ∼1.1 nm (sample 1) and ∼1.4 nm (sample 2) sizes, respectively. STM analysis showed that, the quantum dots are spherical shaped and highly monodispersed. At first, the linear absorption coefficients for two different sizes of SnO₂ quantum dots were measured by employing a CW He-Ne laser at 632.8 nm and were obtained about 1.385 and 4.175 cm⁻¹, respectively. Furthermore, the nonlinear refractive index, n₂, and nonlinear absorption coefficient, β, were measured using close and open aperture Z-scan respectively using the same laser. As quantum dots have strong absorption coefficient to obtain purely effective n₂, we divided the closed aperture transmittance by the corresponding open aperture in the same incident beam intensity. The nonlinear refraction indices of these quantum dots were measured in order of 10⁻⁷ (cm²/W) with negative sign and the nonlinear absorption coefficients were obtained for both in order of 10⁻³ (cm/W) with positive sign.     

Microwave absorption in 2HNbSe2 and critical fluctuations above Tc

Large three-dimensional critical fluctuations above T_c have been observed in 2HNbSe₂ compounds by microwave absorption.     

Investigation of the optoelectronic properties of columbite ZnNb2O6 crystal

A high-quality ZnNb₂O₆ single-crystal grown by optical floating zone method has been used as a research prototype to analyze the optoelectronic parameters by measuring the absorption coefficient and transmittance spectra along the b-axis from 200 nm to 1000 nm at room temperature. The optical interband transitions of ZnNb₂O₆ have been determined as a direct transition with a band gap of 3.84 eV. The refractive index, extinction coefficient, and real and imaginary parts of the complex dielectric constants as functions of the wavelength for ZnNb₂O₆ crystal are obtained from the measured absorption coefficients and transmittance spectra. In the Urbach tail of 3.16–3.60 eV, the validity of the Cauchy–Sellmeier equation has also been evaluated. Using the single effective oscillator model, the oscillator energy E_o is found to be 4.77 eV. The dispersion energy E_d is 26.88 eV and ZnNb₂O₆ crystal takes an ionic value.     

Microwave and electrical properties of Co-Ti substituted M-type Ba hexagonal ferrite

The microwave characteristics of Co²⁺ and Ti⁴⁺ ions substituted, BaCo _x Ti _x Fe_(12?2x)O₁₉ (x = 0.1, 0.3, 0.5, 0.7, 0.9) ferrite have been studied as a function of thickness, frequency and substitution. The results depict reflection loss of ? 31.94 dB at 10.47 GHz in x = 0.9. The highest static electrical current is observed at lower substitution. The model accompanying microwave absorption is used to evaluate microwave absorption characteristics. The electromagnetic and static electrical characteristics are improved with the substitution of Co²⁺ and Ti⁴⁺ ions. The compositions for possible electromagnetic applications are also explored.     

Absolute diode-laser frequency calibration using varactor mixing with a stabilized CO2 laser. Ozone spectrum near the 9R6 CO2 frequency

Efficient infrared varactor mixing near 9 μm has been performed between diode-laser and CO₂ laser. Difference frequency up to 17 GHz has been detected using non linear mixing between the two radiations and the first four harmonics of a microwave frequency (f = 4.2 GHz). As a result, the absorption spectrum of ozone near the 9R₆ CO₂ line is frequency scaled over a 1.7 cm^-1 range with microwave accuracy.     

Electromagnetic and microwave absorbing properties of Co2Z-type hexaferrites doped with La

Z-type ferrites doped with La³⁺, Ba_3−xLa_xCo₂Fe₂₄O₄₁ (x=0.00-0.30), were prepared by sol-gel method. The effect of the substitution La³⁺ rare-earth ions for Ba²⁺ ions on the microstructure, complex permeability, permittivity and microwave absorption of the samples was investigated. The results show that the major phase of the ferrites changed to Z-phase when sintering temperature was 1250 °C for 5 h. With the increase of the substitution ratio of La³⁺ ions from 0.0 to 0.3, the lattice parameters a and c increased gradually, which resulted in the change of the particle shape and size. The data of magnetism showed that the addition of La³⁺ ions make the ferrite a better soft magnetic material due to increase of magnetization (σ_s) and decrease of coercivity (H_c). The La³⁺ ions doped in the ferrite not only improved complex permeability and complex permittivity, but also microwave absorbency.     

Specific features of photo and thermoluminescence of Tb ions in BaO-M2O3 (M=Ga, Al, In)-P2O5 glasses

BaO-P₂O₅ glasses mixed with the three metal oxides viz., Al₂O₃, Ga₂O₃ and In₂O₃ doped with Tb₂O₃ were prepared. The glasses were characterized by X-ray diffraction and differential thermal analysis. Optical absorption and photoluminescence spectra and thermoluminescence (TL) of these glasses have been studied. From the measured intensities of various absorption bands of these glasses, the Judd-Ofelt parameters Ω₂, Ω₄ and Ω₆ have been evaluated and compared with those of other reported glass systems. The Judd-Ofelt theory could successfully be applied to characterize the absorption and luminescence spectra of these glasses. From this theory various radiative properties like transition probability A, branching ratio β_r, the radiative lifetime τ_r and the emission cross-section σ^E for various emission levels of these glasses have been determined and reported. An attempt has also been made to throw some light on the relationship between the structural modifications and luminescence efficiencies of all the three glasses. The analysis of TL data indicate high non-radiative losses in In₂O₃ mixed glasses.     

The microwave absorption properties of La0.8Sr0.2Mn1−yFeyO3 nanocrystalline powders in the frequency range 2-18 GHz

La_1−xSr_xMn_1−yFe_yO₃ nanocrystalline powders were prepared by the sol-gel method as a microwave absorption material. The reflectance, the dielectric loss tan δ_e and the magnetic loss tan δ_m of the samples were calculated according to the data of electromagnetism parameters measured by a microwave vector network analyzer in the frequency range 2-18 GHz. The dielectric loss tan δ_e and the magnetic loss tan δ_m had a step-change at a certain frequency so that the superiority of dielectric loss change into the superiority of magnetic loss, which indicated that anti-ferromagnetic clusters in the material change into ferromagnetic clusters by absorbing quantum of microwave electromagnetic field when the frequency of incident microwave reaches a certain value. The effective absorption bandwidth higher than 10 dB reached 6.2 GHz. As a result, the La_0.8Sr_0.2Mn_1−yFe_yO₃ has shown useful applications as a microwave absorption material.     

Infrared and microwave high-resolution spectrum of the ν3 band of ozone

The vibration-rotation band ν₃ of ozone has been recorded with a high-resolution (0.012 cm^?1) spectrometer, and microwave absorption spectra of ozone have been identified in the excited vibrational states (100) and (001). A strong Coriolis interaction has been observed. More than 1200 spectral lines have been identified in the ν₃ band, using a Watson-type Hamiltonian, including all the sextic centrifugal distortion terms. Band constants and an atlas listing line wavenumbers, intensities, and assignments are given, from 1007 to 1072 cm^?1. It is shown that transitions with high values of the quantum numbers K_?1 (≥11) contribute to significant absorption.