Luminescence studies on SrMgAl10O17:Eu, Dy phosphor crystals

Using urea as fuel, SrMgAl₁₀O₁₇:Eu, Dy phosphor was prepared by a combustion method. Its luminescence properties under ultraviolet (UV) excitation were investigated. Pure SrMgAl₁₀O₁₇ phase was formed by urea-nitrate solution combustion synthesis at 550 °C. The results indicated that the emission spectra of SrMgAl₁₀O₁₇:Eu, Dy has one main peak at 460 nm and one shoulder peak near 516 nm, which are ascribed to two different types of luminescent Eu²⁺ centers existing in the SrMgAl₁₀O₁₇ matrix crystal. The blue luminescence emission of SrMgAl₁₀O₁₇:Eu phosphors was improved under UV excitation by codoping Dy³⁺ ions. The SrMgAl₁₀O₁₇:Eu phosphors showed green afterglow (λ=516 nm) when Dy³⁺ ions were doped. Dy³⁺ ions not only successfully play the role of sensitizer for energy transfer in the system, but also act as trap levels and capture the free holes in the spinel blocks.     

Sr2CeO4:Eu and Sr2CeO4:5 mol% Eu, 3 mol% Dy microphosphors: Wet chemistry synthesis from hybrid precursor and photoluminescence properties

In this article, Sr₂CeO₄:x mol% Eu³⁺ and Sr₂CeO₄:5 mol%Eu³⁺, 3 mol% Dy³⁺ phosphors were synthesized from assembling hybrid precursors by wet chemical method. As-prepared samples present uniform grain-like morphology and the particle size is about 0.2 μm. The luminescence spectra of Sr₂CeO₄:x mol% Eu³⁺ have been measured to examine the influence of the intensity of red emission lines for Eu³⁺ on the concentration of Eu³⁺, showing that the intensity of the red emission increases with an increase of the concentration from 1 to 5 mol%. Additionally, from the emission spectra of Sr₂CeO₄:5 mol%Eu³⁺, 3 mol% Dy³⁺ phosphors, the characteristic lines of Dy³⁺ have also been observed. This result indicates that there also exists an energy transfer process between Sr₂CeO₄ and Dy³⁺.     

Comparative investigation on spectroscopic properties of Er between Ce-doped and B2O3-added bismuth glasses

The comparative investigation on the spectroscopic properties of Er³⁺ in low phonon energy Bi₂O₃-GeO₂-Ga₂O₃-Na₂O glasses codoped with Ce³⁺ ion and added with B₂O₃ component, respectively, is presented. With increasing Ce₂O₃ content from 0 to 0.8 mol% or B₂O₃ content from 0 to 15 mol%, the lifetime of Er³⁺:⁴I_11/2 level decreases dramatically from 607 to 283 μs or to 197 μs, and the upconversion fluorescence is quenched in both glass samples. The nonradiative energy transfer from Er³⁺:⁴I_11/2→Ce³⁺:²F_5/2 or the enhanced multiphonon relaxation process together with the energy transfer between Er³⁺ and OH⁻ groups are, respectively, responsible for the results. Meanwhile, the lifetime of ⁴I_13/2 level remains almost unchanged in Er³⁺/Ce³⁺-codoped glasses whereas it decreases rapidly in B₂O₃-added cases. As a result, Er³⁺/Ce³⁺ codoping improves the 1.5 μm fluorescence emission intensity, however, B₂O₃ addition has a negative effect on it. The research results indicate that the Er³⁺/Ce³⁺-codoped bismuth glasses will be preferable for obtaining efficient 980 nm pumped EDFA.     

Photoluminescence and thermoluminescence characterization of Eu- and Dy -activated Ca3(PO4)2 phosphor

Rare-earth-doped polycrystalline Ca₃(PO₄)₂:Eu, Ca₃(PO₄)₂:Dy and Ca₃(PO₄)₂:Eu,Dy phosphors prepared by a modified solid-state synthesis has been studied for its X-ray diffraction, thermoluminescence (TL) and photoluminescence (PL) characteristics. The PL emission spectra of the phosphor suggest the presence of Eu³⁺ ion in Ca₃(PO₄)₂:Eu and Dy³⁺ ion in Ca₃(PO₄)₂:Dy lattice sites. The TL glow curve of the Ca₃(PO₄)₂:Eu compounds has a simple structure with a prominent peak at 228 °C, while Ca₃(PO₄)₂:Dy peaking at 146 and 230 °C. TL sensitivity of phosphors are compared with CaSO₄: Dy and found 1.52 and 1.20 times less in Ca₃(PO₄)₂:Eu and Ca₃(PO₄)₂:Dy phosphors, respectively. The Ca₃(PO₄)₂:Eu,Dy phosphors shows switching behavior under two different excitation wavelengths and enhancement in PL intensity of Dy³⁺ ions were reported. The paper discusses the photoluminescence and thermoluminescence behavior of Eu³⁺ and Dy³⁺ ion in Ca₃(PO₄)₂ hosts, it may be applicable to solid-state lighting as well as thermoluminescence dosimetry applications.     

Luminescence investigations on sulfate apatite Na6(SO4)2FCl:RE (RE=Dy, Ce or Eu) phosphors

A new phosphor in the Cl-F system doped with Dy, Ce and Eu has been reported. Characterization of this phosphor using XRD, PL and TL techniques is described. Polycrystalline Na₆(SO₄)₂FCl:Dy; Na₆(SO₄)₂FCl:Ce and Na₆(SO₄)₂FCl:Eu phosphors prepared by a solid state diffusion method have been studied for their X-ray diffraction, photoluminescence (PL) and thermoluminescence (TL)characteristics. The PL excitation and emission spectra of phosphors were obtained. Dy³⁺ emission in the host at 475 and 570 nm is observed due to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transition, respectively, whereas the PL emission spectra of Na₆(SO₄)₂FCl:Ce phosphor shows the Ce³⁺ emission at 322 nm due to 5d→4f transition of Ce³⁺ ion. In Na₆(SO₄)₂FCl:Eu lattice, Eu²⁺ as well as Eu³⁺ emissions are observed. The emission of europium ion in this compound exhibits the blue as well as red emission. The TL glow curves of the same compounds have the simple structure with a prominent peak at 150, 175 and 200 °C. TL response, fading, reusability and trapping parameters of the phosphors are also studied. The TL glow curves of γ-irradiated Na₆(SO₄)₂FCl sample show one glow peak indicating that only one set of traps is being activated within the particular temperature range each with its own value of activation energy (E) and frequency factor (s). The trapping parameters associated with the prominent glow peak are calculated using Chen’s half width method. The release of hole/electron from defect centers at the characteristic trap site initiates the luminescence process in these materials. The intensity of the TL glow peaks increases with increase of the added γ-ray dose to the samples.     

A novel blue-emitting long-lasting proyphosphate phosphor Sr2P2O7:Eu,Y

By introducing the Y³⁺ into Sr₂P₂O₇:Eu²⁺, we successfully prepared a kind of new phosphor with blue long-lasting phosphorescence by the high-temperature solid-state reaction method. In this paper, the properties of Sr₂P₂O₇:Eu²⁺,Y³⁺ were investigated utilizing XRD, photoluminescence, luminescence decay, long-lasting phosphorescence and thermoluminescence (TL) spectra. The phosphor emitted blue light that was related to the 4f⁶5d¹-⁸S_7/2 transition of Eu²⁺. The bright blue phosphorescence could be observed by naked eyes even 8 h after the excitation source was removed. Two TL peaks at 317 and 378 K related to two types of defects appeared in the TL spectrum. By analyzing the TL curve the depths of traps were calculated to be 0.61 and 0.66 eV. Also, the mechanism of LLP was discussed in this report.     

Combustion synthesis and photoluminescence of Eu, Dy-doped La2Zr2O7 nanocrystals

A facile and energy saving sol-gel combustion method has been used to prepare La₂Zr₂O₇ nanocrystallines. The pyrochlore La₂Zr₂O₇ nanocrystals have been obtained at a relatively low temperature with the grain size ranging from 45 to 70 nm. Eu³⁺ and Dy³⁺ have been introduced into the La₂Zr₂O₇ crystal structure, respectively, and the intense photoluminescence was observed. The relative intensity of electric dipole transition and magnetic dipole transition is considered for luminescence emission both of Eu³⁺ and Dy³⁺. The dependence of luminescence intensity on dopant concentration and the effect of Dy³⁺ co-doping on Eu³⁺ luminescence are also discussed.     

Synthesis and luminescence properties of needle-like SrAl2O4:Eu, Dy phosphor via a hydrothermal co-precipitation method

Needle-like SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had been prepared by calcining the precursors obtained from hydrothermal process at the temperature of 1100 °C in a weak reductive atmosphere of active carbon. The crystal structure, morphology and optical properties of the composites were characterized. X-ray diffraction (XRD) patterns illustrated that the single-phase SrAl₂O₄ was formed at 1100 °C, which is much lower than that prepared by the traditional method. The transmission electron microscope (TEM) observation revealed the precursors and the resulted SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had well-dispersed distribution and needle-like morphology with an average diameter about 150 nm at the center and the length up to 1 μm. After irradiation by ultraviolet radiation with 350 nm for 5 min, the phosphors emit green color long-lasting phosphorescence corresponding to the typical emission of Eu²⁺ ion, both the PL spectra and luminance decay revealed that the phosphors had efficient luminescent and long lasting properties.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Enhanced luminescence of Ca3B2O6:Dy phosphors by Na-codoping for LED applications

The Ca_2.95−yDy_0.05B₂O₆:yNa⁺ (0≤y≤0.20) phosphors were synthesized at 1100 °C in air by the solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE), photoluminescence (PL) spectra and thermoluminescence (TL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid-state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions on 350 nm excitation was observed at 480 nm (blue) due to the ⁴F_9/2→⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2→⁶H_13/2 transitions and 660 nm (red) due to weak ⁴F_9/2→⁶H_11/2 emissions. The PL results from the investigated Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors show that Dy³⁺ emissions increase with the increase of the Na⁺ codoping ions. The integral intensity of yellow to blue (Y/B) can be tuned by controlling Na⁺ content. By the simulation of white light, the optimal CIE value (0.328, 0.334) can be achieved when the content of Na⁺-codoping ions is y=0.2. The results imply that the Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors could be potentially used as white LEDs.     

Thermoluminescence studies on Cu-doped Li2B4O7 single crystals

Lithium tetraborate (Li₂B₄O₇) is a tissue equivalent material and single crystals of this material doped with Cu are promising for dosimetric applications. In the present study highly transparent single crystals of lithium tetraborate (Li₂B₄O₇) doped with Cu (0.5 wt%) have been grown using the Czochralski technique. The Li₂B₄O₇:Cu crystals were studied using photoluminescence, X-ray diffraction (XRD), UV-vis transmission, time resolved fluorescence and thermoluminescence (TL) techniques. The TL readout of Li₂B₄O₇:Cu crystals showed two well-defined glow peaks at 402 K (peak-1) and 513 K (peak-2) for a 4 K/s heating rate. While the low temperature TL peak-1 fades completely within 24 h at room temperatures, the main dosimetric peak-2 remains the same. The TL sensitivity of the grown single crystal is found to be 3.3 times that of a conventional TL phosphor, TLD-100. The Li₂B₄O₇:Cu crystals showed a linear TL dose-response in the range from 1 mGy to 1 kGy. The TL analysis using a variable dose method revealed first order kinetics for both the peaks. Trap depth and frequency factor for peak-1 were found to be 0.81 eV and 5.2×10⁹ s⁻¹, whereas for peak-2 the values were 1.7 eV and 1.7×10¹⁶ s⁻¹, respectively.     

Effect of Bi2O3 on EPR, optical transmission and DC conductivity of vanadyl doped alkali bismuth borate glasses

Glasses with composition xBi₂O₃·(30−x)M₂O·70B₂O₃ (M=Li, Na) containing 2 mol% V₂O₅ have been prepared over the range 0≤x≤15 (x is in mol%). The electron paramagnetic resonance spectra of VO²⁺ of these glasses have been recorded in the X-band (≈9.3 GHz) at room temperature (RT≈300 K). Spin Hamiltonian parameters, g_∥, g_⊥, A_∥, A_⊥, dipolar hyperfine coupling parameter, P, and Fermi contact interaction parameter, K, have been calculated. The molecular orbital coefficients, α² and γ², have been calculated by recording the optical transmission spectra. In xBi₂O₃·(30−x)Li₂O·70B₂O₃ glasses there is decrease in the tetragonality of the V⁴⁺O₆ complex for x up to 6 mol% whereas for x≥6 mol%, tetragonality increases. In xBi₂O₃·(30−x)Na₂O·70B₂O₃ glasses there is increase in the tetragonality of the V⁴⁺O₆ complex with increasing x. The 3d_xy orbit expands with increase in Bi₂O₃:M₂O ratio. Values of the theoretical optical basicity, Λ_th, have also been reported. The DC conductivity increases with increase in temperature. The order of conductivity is 10⁻⁵ ohm⁻¹ m⁻¹ at low temperature and 10⁻³ ohm⁻¹ m⁻¹ at high temperature. The DC conductivity decreases and the activation energy increases with increase in Bi₂O₃:M₂O ratio.     

Photoluminescence and phosphorescence properties of MAl2O4:Eu, Dy (M=Ca, Ba, Sr) phosphors prepared at an initiating combustion temperature of 500 °C

Eu²⁺ and Dy³⁺ co-doped calcium aluminate, barium aluminate and strontium aluminate phosphors were synthesized at an initiating combustion temperature of 500 °C using urea as an organic fuel. The crystallinity of the phosphors was investigated by using X-ray diffraction (XRD) and the morphology was determined by a scanning electron microscope (SEM). The low temperature monoclinic structure for both CaAl₂O₄ and SrAl₂O₄ and the hexagonal structure of BaAl₂O₄ were observed. The effect of the host materials on the photoluminescence (PL) and phosphorescence properties were investigated by using a He-Cd Laser and a Cary Eclipse fluorescence spectrophotometer, respectively. The broad band emission spectra observed at 449 nm for CaAl₂O₄:Eu²⁺, Dy³⁺, 450 nm (with a shoulder-peak at 500 nm) for BaAl₂O₄:Eu²⁺, Dy³⁺ and 528 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ are attributed to the 4f⁶5d¹ to 4f⁷ transition in the Eu²⁺ ion in the different hosts.     

Thermoluminescence of B2O3-Li2O glass system doped with MgO

Lithium borate (LiB) glasses in the system (100−x)B₂O₃-xLi₂O with x=20, 30, 40, 50, 60 and 70 mol% were prepared. The glasses were doped with different concentrations of the order of 10⁻¹, 10⁻², 10⁻³, 10⁻⁴ and 10⁻⁵ of MgO and their thermoluminescent (TL) response was investigated. The irradiations were performed using γ rays from a ⁶⁰Co source in the dose range from 0.1 to 25 kGy. The material displayed good sensitivity for γ-rays and intensity of TL signals is dependent on γ-ray dose and Li₂O content. For each dose level and investigated temperature range (50-350 °C), exactly single isolated glow peak appears in the temperature range of 165-205 °C depending on both Li₂O concentrations and time of exposure. The shape of the glow peak has altered significantly with increase in the gamma ray dose or Li₂O concentrations. The glass composition with x=50 mol% doped with 10⁻³ mol% of MgO presented the best TL response. The results of the present study indicated that the recorded single and isolated high temperature peak is a good candidate for TL dosimetric investigations. This indicates that 50 B₂O₃-50Li₂O-doped with 10⁻³ mol% of MgO is possibly used as materials for radiation dosimetry in the dose range of 0.1-20 kGy.     

A simple photochemical method to synthesize Ga2O3-Dy-M thin films and their evaluation as optical materials (where M=Cr or Co)

We report the photochemical method to synthesize Ga₂O₃-Dy³⁺-Co³⁺ and Ga₂O₃-Dy³⁺-Cr³⁺ thin films. X-ray photoelectron spectroscopy, X-ray diffraction and photoluminescence were used to characterize the products. These analyses revealed that as-deposited and annealed films are amorphous. The optical characterization of the films showed that these are highly transparent in the visible spectrum but decrease significantly with doped and co-doped films. Under the excitation of UV light (254 nm) the doped films (Ga₂O₃-Dy³⁺) show the characteristic emissions of Dy³⁺ at 500, 575, 594, 605 and 652 nm corresponding to ⁴F_9/2→⁶H_J ( J=15/2, 13/2 and 11/2) transitions but the emissions decrease with the co-doped films (Ga₂O₃-Dy³⁺-M³⁺, where M=Cr or Co); a possible emission mechanism and energy transfer have been proposed.     

Effect of Dy substitution on structural,magnetic and optical properties of BiFeO3 ceramics

Bi_1−xDy_xFeO₃ (x=0.0, 0.03, 0.05, 0.07, 0.10 and 0.12) ceramics were synthesized by solid state reaction method. Effects of Dy substitution on structural distortion, magnetic and optical properties of BiFeO₃ were examined by X-ray diffraction, Raman and UV–Visible spectroscopy. The samples were found to crystallize in rhombohedral structure of BiFeO₃ with R3c space group. The reduction in lattice parameters and unit cell volume indicate the distortion in FeO₆ octahedra of the rhombohedral structure without any signature of phase transformation up to x=0.12. The predictable weak ferromagnetic hysteresis loops can be observed in the Dy doped samples with maximum remnant magnetization of 0.2103 emu/g for x=0.12. The weak ferromagnetism is ascribed to the suppressed spiral spin structure and magnetically active characteristic of Dy³⁺ ions together with ferromagnetic coupling between Dy³⁺ and Fe³⁺ ions. With optical band gap in visible region, Dy doped BiFeO₃ ceramics are potential material for optoelectronic device and solar cell applications.     

Synthesis and photoluminescence properties of NaPbB5O9:Dy phosphor materials for white light applications

Given the recent increased interest in phosphor materials and their applications, we analyzed a new NaPbB₅O₉:Dy³⁺ phosphor material with different concentrations of Dy³⁺. In particular, we investigated the crystal structure, morphology, and luminescence properties of these materials. X-ray diffraction analyses confirmed the formation of NaPbB₅O₉:Dy³⁺ phosphor powder. The functional groups present in the phosphor materials were examined by Fourier transform infrared spectroscopy. Scanning electron microscope images showed that the size of the grains was in the micrometer range. Photoluminescence spectra were recorded at different excitation wavelengths for the phosphor materials and we analyzed the variation in the intensity of the emission bands with different concentrations of Dy³⁺ ions. The color co-ordinates were calculated and used to characterize the color of the phosphor. We found that the emission colors of the Dy³⁺-doped NaPbB₅O₉ powders depended on the Dy³⁺ ion doping concentration and the excitation wavelength.     

Comparative structural and photoluminescent study of Eu-doped La2O3 and La(OH)3 nanocrystalline powders

Eu³⁺-doped La₂O₃ nanocrystalline powder was prepared by polymer complex solution method and further used for preparation of Eu³⁺-doped La(OH)₃. Structural and optical characterization was carried out by powder X-ray diffraction and photoluminescent spectroscopy. XRD measurements confirmed the formation of hexagonal La₂O₃ and its recrystallization into La(OH)₃ in a humid atmosphere. Excitation spectra show redshift of host lattice and charge transfer emission bands in La(OH)₃ while bands that correspond to Eu³⁺f–f transitions are placed at same wavelengths in both samples. Photoluminescence spectra recorded over the temperature range from 10 K to 300 K show that intensities of emission lines in Eu³⁺-doped La₂O₃ do not depend on temperature as much as in La(OH)₃ sample. Observed dominant ⁵D₀→⁷F₂ and markedly visible ⁵D₀→⁷F₀ emissions in doped La₂O₃ indicate that Eu³⁺ ion is located in a structural site without an inversion center. On the other hand, in Eu³⁺-doped La(OH)₃⁵D₀→⁷F₀ transition is barely visible while ⁵D₀→⁷F₂ is not prominent, and with temperature drop three ⁵D₀→⁷F_J (J=1, 2, 4) transitions become almost of the same intensity. In both La₂O₃ and La(OH)₃ structures Eu³⁺ ion replaces La³⁺ in non-centrosymmetric C_3v and C_3h crystallographic sites, respectively, and difference in symmetry of the crystal field around europium ion is explained by comparing shape and volume of these sites. Decay times of the ⁵D₀- level recorded over the temperature range 10−300 K revealed that emission lifetime values in La₂O₃ (~0.7 ms) are almost two times higher than in La(OH)₃ (~0.4 ms), and unlike in La₂O₃, lifetime in La(OH)₃ is temperature dependent.     

Photoluminescence of Y2O3:Eu thin film phosphors by sol-gel deposition and rapid thermal annealing

Y₂O₃:Eu³⁺ phosphor films have been developed by using the sol-gel process. Comprehensive characterization methods such as Photoluminescent (PL) spectroscopy, X-ray diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy were used to characterize the Y₂O₃:Eu³⁺ phosphor films. In this experiment, the XRD profiles show that the Y₂O₃:Eu³⁺ phosphor films crystallization temperature and optimum annealing temperature occur at about 650 and 750 °C, respectively. The optimum dopant concentration is 12 mol% Eu³⁺ and the critical transfer distance (R_c) among Eu³⁺ ions is calculated to be about 0.84 nm. Vacuum environment is more efficient than oxygen and nitrogen to eliminate the OH content and hence yields higher luminescent phosphor films. The PL emission intensity of Y₂O₃:Eu³⁺ phosphor films is also dependent on the annealing time. It was found that the H₂O impurities were effectively eliminated after annealing time of 25 s at 750 °C in vacuum environment. From the experiment results, the schematic energy band diagram of Y₂O₃:Eu³⁺ phosphor films is constructed.     

Advances in synthesis and characterization of LiMgBO3:Dy

The low Z polycrystalline LiMgBO₃:Dy³⁺ material has been successfully synthesized by novel solution combustion synthesis and studied for its luminescence characteristics. LiMgBO₃:Dy³⁺ material has shown promising TL sensitivity with a broad dosimetric glow peak at 154 °C. Near the tissue equivalent TL phosphor with Dy dopant has half of the TL sensitivity as compared to commercial TLD-100. The kinetic parameters i.e. trap depth or activation energy and frequency factor from the glow curve derived by using peak shape method. The main dosimetric characteristics such as dose response and fading effect are investigated. The state of dopant confirmed using photoluminescence spectra.