4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Synthesis and photovoltaic investigation of dithieno[2,3‐d:2′,3′‐d′]‐benzo[1,2‐b:3,4‐b′:5,6‐d″]trithiophene‐based conjugated polymer with an enlarged π‐conjugated system

Compared with benzo[1,2‐b:3,4‐b′:5,6‐d″]trithiophene (BTT), an extended π‐conjugation fused ring derivative, dithieno[2,3‐d:2′,3′‐d′]benzo[1,2‐b:3,4‐b′:5,6‐d″]trithiophene (DTBTT) has been designed and synthesized successfully. For investigating the effect of extending conjugation, two wide‐bandgap (WBG) benzo[1,2‐b:4,5‐b′]dithiophene (BDT)‐based conjugated polymers (CPs), PBDT‐DTBTT, and PBDT‐BTT, which were coupled between alkylthienyl‐substituted benzo[1,2‐b:4,5‐b′]dithiophene bistin (BDT‐TSn) and the weaker electron‐deficient dibromides DTBTTBr₂ and BTTBr₂ bearing alkylacyl group, were prepared. The comparison result revealed that the extending of conjugated length and enlarging of conjugated planarity in DTBTT unit endowed the polymer with a wider and stronger absorption, more ordered molecular structure, more planar and larger molecular configuration, and thus higher hole mobility in spite of raised highest occupied molecular orbital (HOMO) energy level. The best photovoltaic devices exhibited that PBDT‐DTBTT/PC₇₁BM showed the power conversion efficiency (PCE) of 2.73% with an open‐circuit voltage (V_OC) of 0.82 V, short‐circuit current density (J_SC) of 6.29 mA cm^?2, and fill factor (FF) of 52.45%, whereas control PBDT‐BTT/PC₇₁BM exhibited a PCE of 1.98% under the same experimental conditions. The 38% enhanced PCE was mainly benefited from improved absorption, and enhanced hole mobility after the conjugated system was extended from BTT to DTBTT. Therefore, our results demonstrated that extending the π‐conjugated system of donor polymer backbone was an effective strategy of tuning optical electronic property and promoting the photovoltaic property in design of WBG donor materials.     

Synthesis and functionalization of Poly[5,5′‐(silylene)‐2,2′‐dithienylene]s using silyl triflate intermediates†

Treatment of 5,5′‐dilithio‐2,2′‐dithiophene with (dimethylamino)methylsily bis(triflate)‐ or α, ω‐bis(triflate)‐substituted trisilanes gave poly[5,5′‐(silylene)‐2,2′‐dithienylene]s in high yields. The amino–silyl bond was cleaved selectively by triflic acid, leading to triflate‐substituted derivatives. Conversion of these compounds with nucleophiles gave other functionalized polymers. Platinum‐catalyzed hydrosilylation reactions between silicon–vinyl and silicon–hydrogen derivatives result in polymer networks which may serve as interesting preceramic materials. The structures of the polymers were proven by NMR spectroscopy (²⁹Si, ¹³C, ¹H). Results of thermal gravimetric analysis (TGA), UV spectrometry and conductivity measurements are given. Copyright © 1999 John Wiley & Sons, Ltd.     

α,α′‐Diarylacenaphtho[1,2‐c]phosphole P‐Oxides: Divergent Synthesis and Application to Cathode Buffer Layers in Organic Photovoltaics

A divergent method for the synthesis of α,α′‐diarylacenaphtho[1,2‐c]phosphole P‐oxides has been established; α,α′‐dibromoacenaphtho[c]phosphole P‐oxide, which was prepared through a Ti^II‐mediated cyclization of 1,8‐bis(trimethylsilylethynyl)naphthalene, underwent a Stille coupling with three different kinds of aryltributylstannanes to afford the α,α′‐diarylacenaphtho[c]phosphole P‐oxides in moderate to good yields. X‐ray crystallographic analyses and UV/Vis absorption/fluorescence measurements have revealed that the degree of π‐conjugation, the packing motif, the electron‐accepting ability, and the thermal stability of the acenaphtho[c]phosphole π‐systems are finely tunable with the α‐aryl substituents. All the P?O and P?S derivatives exhibited high stability in their electrochemically reduced state. To use this class of arene‐fused phosphole π‐systems as n‐type semiconducting materials, we evaluated device performances of the bulk heterojunction organic photovoltaics (OPV) that consist of poly(3‐hexylthiophene), an indene‐C₇₀ bisadduct, and a cathode buffer layer. The insertion of the diarylacenaphtho[c]phosphole P‐oxides as the buffer layer was found to improve the power conversion efficiency of the polymer‐based OPV devices.     

Efficient organic photovoltaic cells based on thiazolothiazole and benzodithiophene copolymers with π‐conjugated bridges

New donor–π–acceptor (D–π–A) type conjugated copolymers, poly[(4,8‐bis((2‐hexyldecyl)oxy)benzo[1,2‐b:4,5‐b′]dithiophene)‐alt‐(2,5‐bis(4‐octylthiophen‐2‐yl)thiazolo[5,4‐d]thiazole)] (PBDT‐tTz), and poly[(4,8‐bis((2‐hexyldecyl)oxy)benzo[1,2‐b:4,5‐b′]dithiophene)‐alt‐(2,5‐bis(6‐octylthieno[3,2‐b]thiophen‐2‐yl)thiazolo[5,4‐d]thiazole)] (PBDT‐ttTz) were synthesized and characterized with the aim of investigating their potential applicability to organic photovoltaic active materials. While copolymer PBDT‐tTz showed a zigzagged non‐linear structure by thiophene π‐bridges, PBDT‐ttTz had a linear molecular structure with thieno[3,2‐b]thiophene π‐bridges. The optical, electrochemical, morphological, and photovoltaic properties of PBDT‐tTz and PBDT‐ttTz were systematically investigated. Furthermore, bulk heterojunction photovoltaic devices were fabricated by using the synthesized polymers as p‐type donors and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester as an n‐type acceptor. PBDT‐ttTz showed a high power conversion efficiency (PCE) of 5.21% as a result of the extended conjugation arising from the thienothiophene π‐bridges and enhanced molecular ordering in the film state, while PBDT‐tTz showed a relatively lower PCE of 2.92% under AM 1.5 G illumination (100 mW/cm²). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1978–1988     

Substituted 2,2′‐Bis(2‐oxidobenzylideneamino)‐4,4′‐dimethyl‐1,1′‐biphenyl Complexes of Zinc

The condensation reaction of 2,2′‐diamino‐4,4′‐dimethyl‐6,6'‐dibromo‐1,1′‐biphenyl with 2‐hydroxybenzaldehyde as well as 5‐methoxy‐, 4‐methoxy‐, and 3‐methoxy‐2‐hydroxybenzaldehyde yields 2,2′‐bis(salicylideneamino)‐4,4′‐dimethyl‐6,6′‐dibromo‐1,1′‐biphenyl ( 1a ) as well as the 5‐, 4‐, and 3‐methoxy‐substituted derivatives 1b , 1c , and 1d , respectively. Deprotonation of substituted 2,2′‐bis(salicylideneamino)‐4,4′‐dimethyl‐1,1′‐biphenyls with diethylzinc yields the corresponding substituted zinc 2,2′‐bis(2‐oxidobenzylideneamino)‐4,4′‐dimethyl‐1,1′‐biphenyls ( 2 ) or zinc 2,2′‐bis(2‐oxidobenzylideneamino)‐4,4′‐dimethyl‐6,6′‐dibromo‐1,1′‐biphenyls ( 3 ). Recrystallization from a mixture of CH₂Cl₂ and methanol can lead to the formation of methanol adducts. The methanol ligands can either bind as Lewis base to the central zinc atom or as Lewis acid via a weak O–H ··· O hydrogen bridge to a phenoxide moiety. Methanol‐free complexes precipitate as dimers with central Zn₂O₂ rings.     

Optimization of the HPLC enantioseparation of 3,3′‐dibromo‐5,5′‐disubstituted‐4,4′‐bipyridines using immobilized polysaccharide‐based chiral stationary phases

The HPLC enantioseparation of nine atropisomeric 3,3′,5,5′‐tetrasubstituted‐4,4′‐bipyridines was performed in normal and polar organic (PO) phase modes using two immobilized polysaccharide‐based chiral columns, namely, Chiralpak IA and Chiralpak IC. The separation of all racemic analytes, the effect of the chiral selector, and mobile phase (MP) composition on enantioseparation and the enantiomer elution order (EEO) were studied. The beneficial effect of nonstandard solvents, such as tetrahydrofuran (THF), dichloromethane (DCM), and methyl t‐butyl ether on enantioseparation was investigated. All selected 4,4′‐bipyridines were successfully enantioseparated on Chiralpak IA under normal or PO MPs with separation factors from 1.14 to 1.70 and resolutions from 1.3 to 6.5. Two bipyridines were enantioseparated at the multimilligram level on Chiralpak IA. Differently, Chiralpak IC was less versatile toward the considered class of compounds and only five bipyridines out of nine could be efficiently separated. In particular, on these columns, the ternary mixture n‐heptane/THF/DCM (90:5:5) as MP had a positive effect on enantioseparation. An interesting phenomenon of reversal of the EEO depending on the composition of the MP for the 3,3′‐dibromo‐5,5′‐bis‐(E)‐phenylethenyl‐4,4′‐bipyridine along with an exceptional enantioseparation for the 3,3′‐dibromo‐5,5′‐bis‐ferrocenylethynyl‐4,4′‐bipyridine (α = 8.33, R_s = 30.6) were observed on Chiralpak IC.     

Using Cyclopenta[2,1‐b:3,4‐c′]dithiophene‐4‐one as a Building Block for Low‐Bandgap Conjugated Copolymers Applied in Solar Cells

A novel electron‐accepting unit cyclopenta[2,1‐b:3,4‐c′]dithiophene‐4‐one (CPDTO‐c′), which is an isomer of CPDTO‐b′ was developed. CPDTO‐c′ can be incorporated into the D–A backbone through 5, 7 positions. The 2 position of CPDTO‐c′ can be easily functionalized with an electron‐withdrawing chain. By copolymerizing CPDTO‐c′ with four different donor units: benzo[1,2‐b:4,5‐b′]dithiophene (BDT), dithieno[3,2‐b:2′,3′‐d]silole (DTS), carbazole, and fluorene, four new conjugated copolymers P1 – P4 were obtained. All these polymers have good solubility and low‐lying HOMO energy levels (−5.41 ∼ −5.92 eV). Among them, P1 and P2 exhibit broad absorption and narrow optical bandgaps of 1.91 and 1.72 eV, respectively. Solar cells based on P1 /PC₇₁BM afforded a PCE up to 2.72% and a high V_oc up to ∼0.9 V.     

Regioselective symmetrical bromination of protected 2,2′‐biimidazole

Treatment of the benzyl and (trimethylsilylethoxymethyl) SEM protected 2,2′‐biimidazoles, 2a and 2b , with 2 equivalents of N‐bromosuccinimide (NBS) allows obtaining the 5,5′‐dibromo and 4,4′‐dibromo substituted biimidazoles, 3a and 5b respectively. The use of 4 equivalents of NBS, followed by treatment of the corresponding tetrabromoderivatives 4a and 5b with butyl lithium (BuLi), yields the 4,4′‐dibromoderiva‐tives 5a (G=Bn) and 5b (G=SEM).     

Synthesis of β,β′‐Porphyrin Dimer Linked by Vinylene

Synthesis of a novel β,β′‐tetraalkylporphyrin dimer linked by vinylene was discribed, in which the dimer was readily prepared from a porphyrin‐derived Wittig reagent and a mono‐formylated porphyrin via Wittig reaction. No π‐conjugation between the two porphyrin rings was obserbed, and the dimer was in trans form.     

Enhancement of the Photovoltaic Performance of CH3NH3PbI3 Perovskite Solar Cells through a Dichlorobenzene‐Functionalized Hole‐Transporting Material

A dichlorobenzene‐functionalized hole‐transporting material (HTM) is developed for a CH₃NH₃PbI₃‐based perovskite solar cell. Notwithstanding the similarity of the frontier molecular orbital energy levels, optical properties, and hole mobility between the functionalized HTM [a polymer composed of 2′‐butyloctyl‐4,6‐dibromo‐3‐fluorothieno[3,4‐b]thiophene‐2‐carboxylate (TT‐BO), 3′,4′‐dichlorobenzyl‐4,6‐dibromo‐3‐fluorothieno[3,4‐b]thiophene‐2‐carboxylate (TT‐DCB), and 2,6‐bis(trimethyltin)‐4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene (BDT‐EH), denoted PTB‐DCB21] and the nonfunctionalized polymer [a polymer composed of thieno[3,4‐b]thiophene (TT) and benzo[1,2‐b:4,5‐b′]dithiophene (BDT), denoted PTB‐BO], a higher power conversion efficiency for PTB‐DCB21 (8.7 %) than that for PTB‐BO (7.4 %) is achieved because of a higher photocurrent and voltage. The high efficiency is even obtained without including additives, such as lithium bis(trifluoromethanesulfonyl)imide and/or 4‐tert‐butylpyridine, that are commonly used to improve the conductivity of the HTM. Transient photocurrent–voltage studies show that the PTB‐DCB21‐based device exhibits faster electron transport and slower charge recombination; this might be related to better interfacial contact through intermolecular chemical interactions between the perovskite and the 3,4‐dichlorobenzyl group in PTB‐DCB21.     

Silylhydrazine und dimere N,N′‐Dilithium‐N,N′‐bis(silyl)hydrazide – Synthesen,Reaktionen, Isomerisierungen

Silylhydrazines and Dimeric N,N′‐Dilithium‐N,N′‐bis(silyl)hydrazides – Syntheses, Reactions, Isomerisations Di‐tert.‐butylchlorosilane reacts with dilithiated hydrazine in a molar ratio to give the N,N′‐bis(silyl)hydrazine, [(Me₃C)₂SiHNH]₂, ( 5 ). Isomeric tris(silyl)hydrazines, N‐difluorophenylsilyl‐N′,N′‐bis(dimethylphenylsilyl)hydrazine ( 7 ) and N‐difluorophenylsilyl‐N,N′‐bis(dimethylphenylsilyl)hydrazine ( 8 ) are formed in the reaction of N‐lithium‐N′‐N′‐bis(dimethylphenylsilyl)hydrazide and F₃SiPh. Isomeric bis(silyl)hydrazines, (Me₃C)₂SiFNHNHSiMe₂Ph ( 9 ) and (Me₃C)₂‐ SiF(PhMe₂Si)N–NH₂ ( 10 ) are the result of the reaction of di‐tert.‐butylfluorosilylhydrazine and ClSiMe₂Ph in the presence of Et₃N. Quantum chemical calculations for model compounds demonstrate the dyotropic course of the rearrangement. The monolithium derivative of 5 forms a N‐lithium‐N′,N′‐bis(silyl)hydrazide ( 11 ). The dilithium salts of 5 ( 13 ) and of the bis(tert.‐butyldiphenylsilyl)hydrazine ( 12 ) crystallize as dimers with formation of a central Li₄N₄ unit. The formation of 12 from 11 occurs via a N′ → N‐silyl group migration. Results of crystal structure analyses are reported.     

Synthesis of a soluble conjugated cumulene polymer: poly(biphenyl‐4,4′‐diyl‐1,4‐bis(4‐dodecyloxyphenyl)‐buta‐1,2,3‐triene‐1,4‐diyl)

A conjugated polymer with a butatriene segment in the main chain, poly(biphenyl‐4,4′‐diyl‐1,4‐bis(4‐dodecyloxyphenyl)buta‐1,2,3‐triene‐1,4‐diyl), was synthesized from 1,4‐bis(4‐bromophenyl)‐1,4‐bis(4‐dodecyloxyphenyl)buta‐1,2,3‐triene by dehalogenative polycondensation using Ni(cod)₂. The polymer was well soluble in usual organic solvents such as CHCl₃ and THF. Structural analyses and characterizations were carried out by IR, NMR, UV‐Vis, PL, and Raman spectroscopy, as well as electrical conductivity. It is suggested that π‐conjugation is extended to some degree through biphenylylene and butatrienylene linkages.     

Parameters influencing the molecular weight of 3,6‐carbazole‐based D‐π‐A‐type copolymers

Condensation copolymerization reactions of carbazole 3,6‐diboronate with 4,7‐bis(5‐bromo‐2‐thienyl)‐2,1,3‐benzothiadiazole (DTBT) only produce low‐molecular‐weight donor (D)‐π‐acceptor (A) copolymers. High‐molecular‐weight copolymers for use in optoelectronic devices are necessary for achieving extended π‐conjugation and for controlling the copolymer processibility. To elucidate the cause of the persistently low molecular weight, we synthesized three 3,6‐carbazole‐based D‐A copolymers using copolymerizations of N‐9′‐heptadecanyl‐3,6‐carbazole with DTBT, N‐9′{2‐[2‐(2‐methoxy‐ethoxy)‐ethoxy]‐ethyl}‐3,‐6‐carbazole with DTBT, and N‐9′‐heptadecanyl‐3,6‐carbazole with alkyl‐substituted DTBT. We investigated several parameters for their influence on molecular copolymer weight, including the conformation of the chain during growth, the solubility of the monomers, and the dihedral angles between the donor and acceptor units. Size exclusion chromatography, UV–vis absorption spectroscopy, and computational studies revealed that the low molecular weights of 3,6‐carbazole‐based D‐A copolymers resulted from conjugation breaks and the resulting high coplanarity, which led to strong interactions between polymer chains. These interactions limited formation of high‐molecular‐weight‐copolymers during copolymerization. The strong intermolecular interactions of the 3,6‐carbazole moiety were exploited by incorporating 3,6‐carbazole units into poly[9′,9′‐dioctyl‐2,7‐flourene‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] prepared from 9′,9′‐dioctyl‐2,7‐flourene and DTBT. Interestingly, the number average molecular weight increased gradually with increasing 2,7‐fluorene monomer content but the number of conjugation breaks was a range of 6–7. The hole mobilities of the copolymers were studied for comparison purposes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of Amphiphilic RuII Heteroleptic Complexes Based on Benzo[1,2‐b:4,5‐b′]dithiophene: Relevance of the Half‐Sandwich Complex Intermediate and Solvent Compatibility

The detailed synthesis and characterization of four ruthenium(II) complexes [RuLL′(NCS)₂] is reported, in which L represents a 2,2′‐bipyridine ligand functionalized at the 4,4′ positions with benzo[1,2‐b:4,5‐b′]dithiophene derivatives (BDT) and L′ is 2,2′‐bipyridine‐4,4′‐dicarboxylic acid unit (dcbpy) (NCS=isothiocyanate). The reaction conditions were adapted and optimized for the preparation of these amphiphilic complexes with a strong lipophilic character. The photovoltaic performances of these complexes were tested in TiO₂ dye‐sensitized solar cell (DSSC) achieving efficiencies in the range of 3–4.5 % under simulated one sun illumination (AM1.5G).     

Synthesis and photophysical properties of 2,5,8,11‐tetrakis(5‐hexylthiophen‐2‐yl)tetrathieno[2,3‐a:3′,2′‐c:2′′,3′′‐f:3′′′,2′′′‐h]naphthalene

The title compound, C₅₈H₆₄S₈, has been prepared by Pd‐catalysed direct C—H arylation of tetrathienonaphthalene (TTN) with 5‐hexyl‐2‐iodothiophene and recrystallized by slow evaporation from dichloromethane. The crystal structure shows a completely planar geometry of the TTN core, crystallizing in the monoclinic space group P2₁/c. The structure consists of slipped π‐stacks and the interfacial distance between the mean planes of the TTN cores is 3.456 (5) Å, which is slightly larger than that of the comparable derivative of tetrathienoanthracene (TTA) with 2‐hexylthiophene groups. The packing in the two structures is greatly influenced by both the aromatic core of the structure and the alkyl side chains.     

Synthesis of Luminescent Ethynyl‐Extended Regioisomers of Borate Complexes Based on 2‐(2′‐Hydroxyphenyl)benzoxazole

A series of thirteen luminescent tetrahedral borate complexes based on the 2‐(2′‐hydroxyphenyl)benzoxazole (HBO) core is presented. Their synthesis includes the incorporation of an ethynyl fragment by Sonogashira cross‐coupling reaction, with the goal of extending the conjugation and consequently redshifting their emission wavelength. Different regioisomers, substituted in the 3‐, 4‐, or 5‐position of the phenolate side of the HBO core, were studied in order to compare their photophysical properties. The complexes were characterized by X‐ray diffraction and NMR, UV/Vis, and emission spectroscopy in solution and in the solid state. In all cases, complexation to boron leads to a donor–acceptor character that impacts their photophysical properties. Complexes with a 3‐ or 5‐substituted fragment display mild to pronounced internal charge transfer (ICT), a feature strengthened by the presence of p‐dibutylaminophenylacetylene in the molecular structure, protonation of the nitrogen atom of which leads to a significant blueshift and an increase in quantum yield. On the contrary, when the ethynyl module is grafted on the 4‐position, narrow, structured, symmetrical absorption/emission bands are observed. Moreover, the fact that protonation has little effect on the emission maximum wavelength reveals singlet excited‐state decay. Solid‐state emission properties reveal a redshift compared to solution, explained by tight packing of the π‐conjugated systems and the high planarity of the dyes. Subsequent connection of these complexes to other photoactive subunits (BODIPY, Boranil) provides dyads in which efficient cascade energy transfer is observed.     

Synthesis and photovoltaic performance of donor–acceptor polymers containing benzo[1,2‐b:4,5‐b′]dithiophene with thienyl substituents

Three alternating donor–acceptor copolymers have been synthesized by Stille coupling polymerization of 2,6‐(trimethyltin)?4,8‐bis(5‐dodecylthiophene‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene with 1,3‐dibromo‐5‐hexylthieno[3,4‐c]pyrrole‐4,6‐dione, 4,7‐dibromo‐1,3‐benzothiadiazole, and 5,7‐dibromo‐2,3‐didodecylthieno[3,4‐b]pyrazine, respectively. The synthesized polymers were tested in bulk heterojunction solar cells as blends with the acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM). The thienopyrroledione copolymer displayed a power conversion efficiency of 3.00% which was increased to 3.86% by application of the additive 1,8‐diiodooctane (DIO). Tapping mode atomic force microscopy analysis indicated that there was an increase in the phase separation between polymer and PCBM, leading to an improvement in the performance upon the addition of DIO. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2622–2630     

Functionalized 3,3′,5,5′‐Tetraaryl‐1,1′‐Biphenyls: Novel Platforms for Molecular Receptors

This paper describes the development of novel aromatic platforms for supramolecular construction. By the Suzuki cross‐coupling protocol, a variety of functionalized m‐terphenyl derivatives were prepared (Schemes 1–4). Macrolactamization of bis(ammonium salt) (S,S)‐ 6 with bis(acyl halide) 7 afforded the macrocyclic receptor (S,S)‐ 2 (Scheme 1), which was shown by ¹H‐NMR titration studies to form ‘nesting' complexes of moderate stability (K_a between 130 and 290 M ^?1, 300 K) with octyl glucosides 13 – 15 (Fig. 2) in the noncompetitive solvent CDCl₃. Suzuki cross‐coupling starting from 3,3′,5,5′‐tetrabromo‐1,1′‐biphenyl provided access to a novel series of extended aromatic platforms (Scheme 5) for cleft‐type (Fig. 1) and macrotricyclic receptors such as (S,S,S,S)‐ 1 . Although mass‐spectral evidence for the formation of (S,S,S,S)‐ 1 by macrolactamization between the two functionalized 3,3′,5,5′‐tetraaryl‐1,1′‐biphenyl derivatives (S,S)‐ 33 and 36 was obtained, the ¹H‐ and ¹³C‐NMR spectra of purified material remained rather inconclusive with respect to both purity and constitution. The versatile access to the novel, differentially functionalized 3,3′,5,5′‐tetrabromo‐1,1′‐biphenyl platforms should ensure their wide use in future supramolecular construction.     

Synthesis and Characterization of Planar Five‐Ring‐Fused Dithiophene‐dione

A series of new organic semiconductors based on s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione was successfully synthesized and characterized. The electron withdrawing carbonyl group lowers the LUMO energy levels, leading to increased electronegativities, which is beneficial for high photo‐stability in air. The n‐alkyl substituted compounds, 1c and 1d , crystallize with the rigid coplanar systems packed into slipped face‐to‐face π‐stacks. Interestingly, 1c and 1d also show liquid crystalline behaviors, which give highly ordered molecular packing over large area.