Tuning hydrophobicity of a fluorinated terpolymer in differently assembled thin films

In the current report, casting from good solvent (acetone) and casting from mixed solvent and nonsolvent were employed for preparing thin films of terpolymer of T etrafluoroethylene (TFE), H exafluoropropylene (HFP), and V inylidene fluoride (VDF) (THV), on silicon wafers. These films revealed various morphologies and wetting behaviors depending on the solution concentration, temperature, and thin film preparation method. The THV thin films prepared by casting from good solvent showed smooth morphology with holes. The thin film prepared from a 3 wt % THV/acetone solution by casting from good solvent at 15 °C demonstrated spheres in addition to the smooth morphology, while the thin film prepared from a 5 wt % THV/acetone solution at 15 °C by casting from good solvent had a mesh‐like structure with some linked spheres. Casting the thin films from mixed solvent and nonsolvent resulted in various morphologies such as different sphere sizes embedded in a dense film layer, and hexagonal close packed structures. The thin films prepared by casting from good solvent showed a slightly hydrophobic character, with a measured water contact angle of approximately 99°, while the nonsolvent cast films had a water contact angle as high as 145°. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 643–657     

基板界面对PS/PMMA溶液共混物溶剂挥发成膜相结构的影响

研究了PS PMMA的共混物溶液溶剂蒸发成膜时的基板界面效应 .利用扫描电子显微镜 (SEM)研究了PS PMMA(5 5 ) (W W) THF高分子共混物溶液在不同基板上通过溶剂挥发成膜的相形态结构 .通过FTIR及ATR FTIR检测了共混物薄膜及其表面的共混组成 .研究结果表明 ,成膜基板对高分子共混物溶液成膜后的相形态有很重要的影响 .控制共混物溶液体系成膜过程中的动力学因素 ,可以调控出所设想的各种复杂的相结构形态     

非对称双嵌段共聚物薄膜在平板受限和溶剂蒸发下自组装行为的分子模拟研究

采用模拟退火和Monte Carlo方法研究体相形成柱状相的双嵌段共聚物薄膜在平板受限和溶剂蒸发条件下的自组装,特别关注柱状相形貌的取向.对于平板受限下的薄膜,研究了表面选择性、溶剂选择性和膨胀程度对柱状相取向的影响.对于溶剂蒸发的薄膜,研究了表面选择性和薄膜厚度对柱状相取向的影响,并讨论了柱状相取向的机理.结果表明,薄膜内存在中性溶剂时形成垂直柱形貌的表面选择性范围较小;存在亲长嵌段的溶剂时形成垂直柱形貌的表面选择性范围较大.溶剂蒸发后薄膜生成垂直柱形貌的参数范围较热退火下增大;柱状相取向取决于蒸发过程中体系由球状相演化为柱状相时的薄膜厚度与体相周期的匹配性.     

Vapochromic behavior of polycarbonate films doped with a luminescent molecular rotor

We report on vapochromic films suitable for detecting volatile organic compounds (VOCs), based on polycarbonate (PC) doped with 4‐(triphenylamino)phthalonitrile (TPAP), a fluorescent molecular rotor sensitive to solvent polarity and viscosity. PC films of variable thickness (from 20 up to 80 µm) and containing small amounts of TPAP (0.05 wt%) were prepared and exposed to a saturated atmosphere of different VOCs. TPAP/PC films showed a gradual decrease and red‐shift of the emission during the exposure to solvents with high polarity index and favorable interaction with the polymer matrix such as THF, CHCl₃, and acetonitrile. In the case of the most interacting solvents (THF and CHCl₃), TPAP/PC films also showed a fluorescence increase at longer exposure times, as a consequence of an irreversible, solvent‐induced crystallization process of the polymeric matrix. The vapochromism of TPAP/PC films is rationalized on the basis of alterations of the rotor intramolecular motion upon solvent uptake by PC and polarity effects of the microenvironment. Interestingly, the fluorescence response of the TPAP/PC films shows a non‐trivial, tuneable dependence on film thickness during the second solvent‐exposure stage. The latter effect is attributed to a variable extent of the crystallization process occurring in the PC films. This observation promptly suggests, in turn, an effective procedure to modulate the spectroscopic response in such functionalized polymeric materials through the precise control of the film thickness. Copyright © 2015 John Wiley & Sons, Ltd.     

Solvent retention in thin polymer films studied by gas chromatography

Thin polystyrene films were produced by spin coating from solutions in toluene. The amount of solvent retained in the films after drying for different times was measured using gas chromatography. Whereas for thicker films (thickness > 200 nm), the relative amount of solvent in the films is less than a few percent, the proportion of toluene increases significantly in thinner films. The thickness dependence of the mass of retained solvent shows that the solvent is mainly retained at the polymer–substrate interface. The solvent desorption rate exhibits no variation on the film thickness.     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

Effect of solvent on the adsorption of benzene vapors by dicyclohexane-18-crown-6 thin films

The solvent effect on the stability of the zero signal of resonators with a dicyclohexane-18-crown-6 film was studied. The adsorption capacity and sensitivity of the film coatings to benzene vapors was estimated. The performance characteristics of the microweighing of benzene vapors were calculated. A model was proposed for benzene adsorption from the gas phase on thin films of crown ether.     

Effect of fullerene C<Subscript>60</Subscript> on the structure and mechanical characteristics of polyethylene: Technological aspect

On the basis of the literature data, a retrospective analysis of the thermodynamic characteristics of dissolution of fullerene C₆₀ in a series of single-ring aromatic solvents is presented. The effect of the molecular structure of a solvent on its dissolving capacity with respect to fullerene is studied. The parameter of the boiling temperature of the solvent normalized to its molecular mass is introduced. The correlation of this parameter with the dissolving capacity of the solvent is discussed. Special emphasis is placed on the effect of halogen-containing solvents on the dissolution of fullerene and indirectly on the development of the mechanical characteristics of films prepared from common solutions of fullerene and low-density polyethylene. For comparison, the films prepared from PE melts modified with low concentrations of fullerene are considered. The film structure is studied via X-ray analysis, optical microscopy, AFM, small-angle scattering of linearly polarized light, and DSC. The films with the maximum strength are prepared from solutions in halogen-containing solvents at a concentration of fullerene below 1 wt %. In this case, spherulites are 5–10 times smaller than those in the films cast from solutions in other solvents. In the films cast from common solutions of PE and fullerene in bromobenzene, crystal solvates C₆₀ · 2C₆H₅Br are formed. It seems that the formation of the crystal solvates binds the residual solvent and thus affects the mechanical behavior of the films, thereby eliminating the plasticizing effect of residual bromobenzene. Localization of fullerene in various regions of the supramolecular structure of the films is discussed, and the morphology of the separating regions of the crystal solvate fullerene phase is analyzed.     

Honeycomb pattern formation via polystyrene/poly(2-vinylpyridine) phase separation

The surface morphologies and properties of polystyrene (PS)/poly(2-vinylpyridine) (PVP) blend films cast on the mica substrate from ethylbenzene solution were investigated upon controlling different weight ratios and solvent evaporation rates. A near-honeycomblike surface morphology of the PS/PVP blend film formed under controlling the solvent evaporation rate due to the effect of Marangoni-Benard convection. The results of static water contact angles, X-ray photoelectron spectroscopy, solvent selective etching, and treatment by water illustrated that the near-honeycomblike structures on the surface of PS/PVP blend films were different for different weight ratios of PS and PVP. After treatment with water for several minutes, PVP islands-like structure emerged in the holes of the film for a PS/PVP weight ratio of 4/1, and a quasihexagonal arrangement of alternate big and small PVP droplets emerged on the top layer of the film for a PS/PVP weight ratio of 7/1. The formation mechanisms of different surface structures and their response behaviors to water were discussed.     

Poly(L‐lactide)/C60 nanocomposites: Effects of C60 on crystallization of poly(L‐lactide)

The effects of solvent type and concentration of C₆₀ on the crystallization of poly(L ‐lactide) (PLLA) during solvent evaporation, heating from room temperature, and cooling from the melt were investigated by polarized optical microscopy and differential scanning calorimetry. The addition of C₆₀ enhanced the PLLA crystallization during solvent evaporation, during heating of the melt‐quenched films, and during cooling from the melt of As‐cast films, except for heating and cooling of the PLLA film with 1 wt % of C₆₀ prepared with dichloromethane. In the case of solvent evaporation, the difference in crystallinity between the PLLA films with and without C₆₀ became higher for the solvent with a lower boiling point. In the case of heating of melt‐quenched films, the addition of C₆₀ had a small effect on the crystallinity of PLLA, whereas significantly lowered the peak top and ending temperatures of cold crystallization, except for melt‐quenched PLLA film with 1 wt % of C₆₀ prepared with dichloromethane. The crystallinity of PLLA was determined by the solvent type, rather than by the C₆₀ concentration. In the case of cooling from the melt of As‐cast films, the addition of C₆₀ elevated the crystallinity and cold crystallization temperature values of PLLA films, except for PLLA films prepared with dichloromethane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2167–2176, 2007     

The effect of casting solvent on the material properties of poly(γ-methyl-D-glutamate)

The effect of casting solvent on the material properties of poly(γ-methyl-D -glutamate), PMDG, was investigated. The specific solvents used were chloroform, trifluoroacetic acid, dichloroacetic acid, methylene chloride, hexafluoroisopropanol, and tetrachloroethane. The different nature of these solvents controlled the degree of α, β, or random coil contents of the final film. The effect of the morphology on material properties induced by the respective solvents was investigated by dynamic mechanical measurements of the dry films, stress strain behavior of both wet and dry films as well as by wide-angle x-ray diffraction, small-angle light scattering, and optical microscopy. Infrared spectroscopy was used to help determine α or β content. It was found that the casting solvent has considerable influence on material behavior and morphology. These differences are reflected in both the dynamical mechanical (small strain) and stress–strain (large strain) measurements as well as the x-ray scattering and optical microscopy. It was noted by light scattering that all films gave rise to anisotropic rod scattering with the exception of the β film cast from trifluoroacetic acid. This latter film appeared to be optically isotropic.     

聚苯乙烯/聚二甲基硅氧烷嵌段共聚物的表面形态研究

采用原子力显微镜(AFM)和透射电镜(TEM)研究了聚苯乙烯/聚二甲基硅氧烷嵌段共聚物(PS-b-PDMS)薄膜的相形态.结果表明,当采用甲苯作为溶剂,旋转涂膜的薄膜样品呈现网络状的形态分布在表面,而样品所对应的透射电镜照片中,PDMS相作为球状分布在PS的连续相中.退火温度对共聚物表面形态有一定的影响,当退火温度高于PDMS的玻璃化温度,表面中PDMS相增多.PS-b-PDMS嵌段共聚物的表面形态随着所用溶剂的变化而有所不同,当采用甲苯作为溶剂时,样品的PS相形成凹坑分布在PDMS的相区之中,而采用环己烷作为溶剂时,PS相作为突起分布在PDMS相区之中.另外,基底对共聚物薄膜表面形态的有较大的影响,当采用硅晶片作为基底时,样品中的PDMS相和PS相呈现近似平行于表面的层状结构.     

Plane hydrodynamic flow in thin free suspended nematic liquid crystal films

Abstract

Radial hydrodynamic flows in free suspended films (with thickness h ≥ 20 μm) of some liquid crystal materials was observed in a narrow temperature range before the line nematic-smectic C transition. The observed flows are explained by a non-linear temperature dependence of the surface tension (Marangoni effect).

Upon thinning the liquid crystal films to a thickness 6 μ < h < 20 μm the hydrodynamic flow changes its character: instead of radial flow with sinking seeding particles we observe two circular plane hydrodynamic flows symmetrical to the film's diameter. The temperature distribution in the free film and the surface tension field are discussed. A model for the established circular flows in thin liquid crystal films is presented.     

Influence of solvent quality on the growth of polyelectrolyte multilayers

The effect of solvent conditions on the growth of polyelectrolyte (PE) multilayer films comprising poly(allylamine hydrochloride) (PAH) and poly(styrenesulfonate sodium salt) (PSS) on planar substrates was investigated by means of surface plasmon resonance spectroscopy (SPRS), quartz crystal microbalance (QCM), and atomic force microscopy techniques. The solvent quality was varied by the addition of ethanol to the PE solutions used for deposition of the layers, thus tuning the relative strength of electrostatic and secondary intermolecular and intramolecular interactions. Experiments were performed with PE solutions both without added electrolyte and containing 0.5 M NaCl. Decreasing the solvent quality (i.e., increasing the amount of ethanol in the adsorption solution) resulted in a marked increase of both the multilayer film thickness and mass loading, as determined from the SPRS spectra and QCM frequency shifts, respectively. With the solution composition approaching the precipitation point, thick PAH/PSS films were formed due to the screening of the electrostatic intra- and interchain repulsions and enhanced hydrophobic interactions between the polyelectrolyte chains. However, the films formed from water/ethanol mixtures remained stable upon subsequent exposure to water or salt-containing solutions: no significant film desorption occurred after up to 24 h of exposure to water or 0.5 M NaCl solutions. In addition, the effect of postdeposition exposure to water/ethanol mixtures was investigated for PE multilayers assembled from aqueous solutions. In this case, the optical thickness of the films was determined during exposure to water/ethanol mixtures, and instead of swelling, the polyelectrolyte films collapse to the surface as a result of the unfavorable segment-solvent interactions.     

Noncrystalline phases in poly(9,9-di-n-octyl-2,7-fluorene)

Selective formation of amorphous, nematic (N), and beta phases in poly(9,9-di-n-octyl-2,7-fluorene) (PFO) films was achieved via judicious choice of process parameters. Phase structure and film morphology were carefully examined by means of X-ray diffraction as well as electron microscopy. "Amorphous" thin films were obtained by quick evaporation of solvent. Slow solvent removal during film formation or extended treatment of the amorphous film with solvent vapor resulted in predominantly the beta phase, which corresponds to a frozen (due to decreased segmental mobility upon solvent removal) and intrinsically metastable state of transformation midway between a solvent-induced clathrate phase and the equilibrium crystalline order in the undiluted state. The frozen transformation process is reactivated upon an increase in temperature beyond 100 degrees C. Compared to the amorphous film, extended backbone conjugation in the beta phase is evidenced from the emergence of a characteristic absorption peak around 430 nm near the absorption edge. For films of frozen nematic order (obtained by quenching from the nematic state), the conjugation length is also greater than the amorphous films as revealed by an absorption shoulder around 420 nm. Well-behaved single-chromophore emission with single-mode phonon coupling was observed for the beta phase; in the case of nematic films, dual-mode phonon coupling must exist if single-chromophore emission is assumed. In comparison, the emission spectrum of the amorphous film of generally shorter conjugation lengths exhibited mixed characteristics of nematic and beta phases, implying the presence of minor populations of extended conjugation similar to those in nematic and beta phases, which are of biased weightings in the emission spectra. All these films consist of nanograins (ca. 10 nm in size) of collapsed chains; the films are therefore inherently inhomogeneous in this length scale. In combination with previous observations on the crystalline (alpha and alpha') forms, the phase behavior of PFO is then generally summarized in terms of relative thermodynamic stability.     

Evaluating the influence of deposition conditions on solvation of reactive conducting polymers with neutron reflectivity

We describe in situ neutron reflectivity (NR) and RAIRS studies of the chemical modification of films of a polypyrrole-based conducting polymer derived from the pentafluorophenyl ester of poly(pyrrole-N-propanoic acid) (PFP) electrodeposited on electrode surfaces. We explore the role of the solvent in controlling the rate of reaction with solution-based nucleophiles (amines, which react with the ester to form amides). By varying the identity of the solvent (water vs acetonitrile) and the neutron contrast (deuteration), we find that both the identity of the solvent and its population within the film are paramount in determining chemical reactivity and electroactivity. IR signatures allow monitoring of the reaction of solution-based amine-tagged species such as amino-terminated poly(propylene glycol), ferrocene ethylamine, and lysine with film-based ester functionalities: the carbonyl bands show ester/amide interconversion and some hydrolysis to acid. Time-dependent spectral analysis shows marked variations in reaction rate with (i) (co-)polymer composition (replacement of some fluorinated ester-functionalized pyrrole with unfunctionalized pyrrole), (ii) the solvent to which the polymer film is exposed, and (iii) the rate of polymer deposition. NR data provide solvent profiles as a function of distance perpendicular to the interface, the variations of which provide an explanation for film reactivity patterns. Homopolymer films are relatively hydrophobic, thus hindering reaction with species present in water solutions. Incorporating pyrrole groups raises the solvent population-dramatically for water-thereby facilitating entry and reaction of aqueous-based lysine. Changing film deposition rate yields films with different absolute levels of solvent and reactivity patterns that are dependent on the size of the reactant molecules: more rapid deposition of polymer gives films with a more open structure leading to a higher solvent content and thence increased reactivity. These results, supported by XPS and AFM data, allow assembly of composition-structure-reactivity correlations, in which the controlling feature is film solvation.     

Probing the early stages of solvent evaporation and relaxation in solvent‐cast polymer thin films by spectroscopic ellipsometry

The formation of solvent‐cast, poly(methyl methacrylate) (PMMA) thin films from dilute bromobenzene solutions was studied using an ellipsometry technique. Bromobenzene has a relatively high refractive index (compared to PMMA), which provides contrast in ellipsometry, allowing the concentration to be determined. The solvent also has a relatively low evaporation rate, which makes the film formation slow enough to capture via the technique. The formation of the glassy film is thus studied in situ, and information on solvent and void concentration in the thin film during the film formation process is obtained. There is evidence that nanovoids (representing intramolecular space) develop in the film when solvent evaporates. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of solvent annealing on the tensile deformation mechanism of a colloidal crystalline polymeric latex film

The influence of solvent annealing on microscopic deformational behavior of a styrene/n-butyl acrylate copolymer latex film subjected to uniaxial tensile deformation was studied by small-angle X-ray scattering. It was demonstrated that the microscopic deformation mechanism of the latex films transformed from a nonaffine deformation behavior to an affine deformation behavior after solvent annealing. This was attributed to the interdiffusion of polymeric chains between adjacent swollen latex particles in the film. It turns out that solvent annealing is much more efficient than thermal annealing due to a much slow evaporation process after solvent annealing.     

Achieving structural control with thin polystyrene-b-polydimethylsiloxane block copolymer films: The complex relationship of interface chemistry,annealing methodology and process conditions

The structure of thin microphase-separated polystyrene-block-polydimethylsiloxane (PS–PDMS) films has been studied using state-of-the-art top-down and cross-sectional electron microscopy. This is the first time that the profile of PS–PDMS films has been measured in situ and these measurements allowed us to image the shape of the PDMS domains within the film as well as examine the wetting behavior of the block copolymer film on a variety of substrates. It was found that for each polymer, substrate chemistry and annealing method combination examined, there was a small range of film thicknesses whereby the films exhibited the optimal characteristics of high levels of ordering without dewetting or multilayering. Specifically, the optimum thickness for films treated by thermal annealing was greater than that for the equivalent solvent annealed film; a change that was correlated with morphology variations related to solvent swelling of the solvent annealed films. The surface chemistry also induced changes in the optimum film thickness. Selective surfaces were shown to control whether a PDMS wetting layer was formed or not, leading to either thicker or thinner wetting optimum film thicknesses; while undulating morphologies were observed for less selective surfaces. Concomitant changes in the periodicity were then hypothesized to occur as a result of confinement effects and the selectivity of the surface.