Two-dimensional ion chromatography using tandem ion-exchange columns with gradient-pulse column switching

A two-dimensional ion chromatography (2D-IC) approach has been developed which provides greater resolution of complex samples than is possible currently using a single column. Two columns containing different stationary phases are connected via a tee-piece, which enables an additional eluent flow and independent control of eluent concentration on each column. The resultant mixed eluent flow at the tee-piece can be varied to produce a different eluent concentration on the second column. This allows analytes strongly retained on the first column to be separated rapidly on the second column, whilst maintaining a highly efficient, well resolved separation of analytes retained weakly on the first column. A group of 18 inorganic anions has been separated to demonstrate the utility of this approach and the proposed 2D-IC method provided separation of this mixture with resolution of all analytes greater than 1.3. Careful optimisation of the eluent profiles on both columns resulted in run times of less than 28 min, including re-equilibration. Separations were performed using isocratic or gradient elution on the first column, with an isocratic separation being used on the second column. Switching of the analytes onto the second column was performed using a gradient pulse of concentrated eluent to quickly elute strongly retained analytes from the first column onto the second column. The separations were highly repeatable (RSD of 0.01–0.12% for retention times and 0.08–2.9% for peak areas) and efficient (typically 8000–260,000 plates). Detection limits were 3–80 ppb.     

Some solutions to obtain very efficient separations in isocratic and gradient modes using small particles size and ultra-high pressure

The UHPLC strategy which combines sub-2 μm porous particles and ultra-high pressure (>1000 bar) was investigated considering very high resolution criteria in both isocratic and gradient modes, with mobile phase temperatures between 30 and 90 °C. In isocratic mode, experimental conditions to reach the maximal efficiency were determined using the kinetic plot representation for ΔP_max = 1000 bar. It has been first confirmed that the molecular weight of the compounds (MW) was a critical parameter which should be considered in the construction of such curves. With a MW around 1000 g mol⁻¹, efficiencies as high as 300,000 plates could be theoretically attained using UHPLC at 30 °C. By limiting the column length to 450 mm, the maximal plate count was around 100,000. In gradient mode, the longest column does not provide the maximal peak capacity for a given analysis time in UHPLC. This was attributed to the fact that peak capacity is not only related to the plate number but also to column dead time. Therefore, a compromise should be found and a 150 mm column should be preferentially selected for gradient lengths up to 60 min at 30 °C, while the columns coupled in series (3× 150 mm) were attractive only for t_grad > 250 min. Compared to 30 °C, peak capacities were increased by about 20–30% for a constant gradient length at 90 °C and gradient time decreased by 2-fold for an identical peak capacity.     

Axial temperature gradient and mobile phase gradient in microcolumn high-performance liquid chromatography

The effect of axial temperature gradient (ATG) along a microcolumn on the separation performance at both isocratic and gradient elution mode was investigated. A thermostat system was designed to form an ATG along the packed column. Polycyclic aromatic hydrocarbons (PAHs) were separated on a 0.53 mm  × 150 mm i.d. 5 μm C₁₈ microcolumn, with water and acetonitrile as mobile phase. The separation results obtained at mobile phase gradient (MPG) and ATG in microcolumn HPLC were compared with the results performed at ambient conditions. Extrapolated curves of peak width at half height (wh)versus lnk showed that wh is narrower at the same retention time when ATG was applied in addition to MPG. The column efficiency was enhanced 20-30% and the resolution was slightly reduced because of reduction of selectivity at elevated temperature at ATG condition. The RSD of retention time in ATG mode was less than 2.5%.     

Separation of intact proteins on porous layer open tubular (PLOT) columns

Porous layer open tubular (PLOT) polystyrene divinylbenzene columns have been used for separating intact proteins with gradient elution. The 10 μm I.D. × 3 m columns were easily coupled to standard liquid chromatography–mass spectrometry (LC–MS) instrumentation with commercially available fittings. Standard proteins separated on PLOT columns appeared as narrow and symmetrical peaks with good resolution. Average peak width increased linearly with gradient time (t_G) from 0.14 to 0.33 min (t_G 20 and 120 min, respectively) using a 3 m column. With shorter columns, peak widths were larger and increased more steeply with gradient time. Theoretical peak capacity (n_c) increased with column length (tested up to 3 m). The n_c increased with t_G until a plateau was reached. The highest peak capacity achieved (n_c = 185) was obtained with a 3 m column, where a plateau was reached with t_G 90 min. The within- and between column retention time repeatabilities were below 0.6% and below 2.5% (relative standard deviation, RSD), respectively. The carry-over following injection of 0.5 ng per protein was less than 1.1%. The retention time dependence on column temperature was investigated in the range 20–50 °C. Proteins in a skimmed milk sample were separated using the method.     

Probing the kinetic performance limits for ion chromatography. II. Gradient conditions for small ions

A gradient kinetic plot method is used for theoretical characterisation of the performance of polymeric particulate anion exchange columns for gradient separations of small inorganic anions. The method employed requires only information obtained from a series of isocratic column performance measurements and in silico predictions of retention time and peak width under gradient conditions. Results obtained under practically constrained conditions provide parameters for the generation of high peak capacities and rapid peak production for fast analysis to be determined. Using this prediction method, a maximum theoretical peak capacity of 84 could be used to achieve separation of 26 components using a 120 min gradient (R_s > 1). This approach provides a highly convenient tool for development of both mono- and multidimensional ion chromatography (IC) methodologies as it yields comprehensive understanding of the influence of gradient slope, analysis time, column length and temperature upon kinetically optimised gradient performance.     

Ion chromatographic determination of some organic acids, chloride and phosphate in coffee and tea

An ion chromatographic method for the simultaneous determination of organic acids and inorganic ions is described. Acetic, malic, ascorbic, citric, malic and succinic acids, chloride and phosphate were determined in coffee and tea samples. The separation is performed on an anion-exchange column operated at 40 °C within 25 min by an isocratic elution with 0.6 mM aqueous potassium hydrogenphthalate (pH 4.0) solution containing 4% (v/v) acetonitrile as eluent and determination by conductivity detection. The method does not need a special sample treatment and was successfully applied to the analysis of black, green and oolong tea samples. Also, green and roasted coffee samples from the varieties arabica and robusta were analyzed.     

High-efficiency liquid chromatography–mass spectrometry separations with 50 mm, 250 mm,and 1 m long polymer-based monolithic capillary columns for the characterization of complex proteolytic digests

In this study, high-efficiency LC–MS/MS separations of complex proteolytic digests are demonstrated using 50 mm, 250 mm, and 1 m long poly(styrene-co-divinylbenzene) monolithic capillary columns. The chromatographic performance of the 50 and 250 mm monoliths was compared at the same gradient steepness for gradient durations between 5 and 150 min. The maximum peak capacity of 400 obtained with a 50 mm column, increased to 485 when using the 250 mm long column and scaling the gradient duration according column length. With a 5-fold increase in column length only a 20% increase in peak capacity was observed, which could be explained by the larger macropore size of the 250 mm long monolith. When taking into account the total analysis time, including the dwell time, gradient time and column equilibration time, the 50 mm long monolith yielded better peptide separations than the 250 mm long monolithic column for gradient times below 80 min (n_c = 370). For more demanding separation the 250 mm long monolith provided the highest peak production rate and consequently higher sequence coverage. For the analysis of a proteolytic digest of Escherichia coli proteins a monolithic capillary column of 1 m in length was used, yielding a peak capacity of 1038 when applying a 600 min gradient.     

A liquid chromatography/positive ion tandem mass spectrometry method for the determination of cilazapril and cilazaprilat in human plasma

A simple, rapid, and sensitive high-performance liquid chromatography (HPLC)-electrospray ionization (ESI) tandem mass spectrometric method (LC-MS/MS) has been developed for simultaneous determination of cilazapril levels and its active metabolite, cilazaprilat, in human plasma using enalapril as internal standard. The acquisition was performed in the multiple reaction monitoring mode; monitoring the transitions: m/z 418.4 > 211.1 for cilazapril and m/z 390.3 > 211.1 for cilazaprilat. The method involves a simple single-step liquid-liquid extraction with ethyl acetate. The analyte was chromatographed on an YMC C₈ reversed-phase chromatographic column by isocratic elution with 10 mM ammonium formate buffer-methanol (10:90, v/v; pH 3.2 with formic acid). Numerous compounds did not interfere with specific multiple reaction monitoring in tandem mass spectrometric detection following C₈ reversed-phase chromatographic separation under conditions that eluted cilazapril, cilazaprilat, and enalapril within 2 min. This method was validated over 0.1-500 ng ml⁻¹ of cilazapril and 0.5-50 ng ml⁻¹ of cilazaprilat. Cilazapril and cilazaprilat were stable in standard solution and in plasma samples under typical storage and processing conditions. The assay was successfully applied to a pharmacokinetic study of cilazapril given as a single oral dose (5 mg) to healthy volunteers.     

Possibilities and Limitations of Computer-Assisted Method Development in HILIC: A Case Study

In the present study, we investigated the possibilities and limitations of computer-assisted method development (CAMD) for the HILIC separation optimization of a mixture of 13 isomeric hydroxy- and aminobenzoic acids on a ZIC-HILIC column. The isocratically obtained Neue and Kuss retention parameters enabled the accurate gradient retention modeling for peaks eluting well within the gradient (mean error of 2.7 %). The prediction errors for peaks eluting at the end of the gradient could be reduced from 8.8 to 6.1 % by implementing the isocratic regime after the gradient into the expression for the gradient retention factor. The prediction of the corresponding peak widths improved significantly for certain compounds and gradient profiles using individual gradient N values for each compound compared to employing a single N value for all compounds and gradient profiles. Two gradient optimization strategies (constructing the R _s map based on individual retention modeling and predictive elution stretching and shifting, PEWS²) resulted in a reasonable separation of the challenging mixture of 13 isomeric hydroxy- and aminobenzoic acids on the ZIC-HILIC column. Overall, the optimization was limited by the steep decrease in N (dropping to the isocratic N value) and corresponding increase in peak width when increasing the gradient time. The discrimination factors d ₀ were used to assess the resolution between peaks varying widely in height. The best separation was found to be obtained via the PEWS² approach. Both the individual retention modeling and PEWS² strategies corresponded to a total instrument time less than 12 h (including equilibration). Finally, it was found that the salt concentration had a significant effect on both the retention and the peak shape of the compounds, resulting in a small “solution domain” at 10 mM. Coupled columns with higher efficiencies are suggested to improve the resolution and robustness of the separation.     

A novel method for determination of low molecular weight dicarboxylic acids in background atmospheric aerosol using ion chromatography

This paper describes a novel gradient elution ion chromatographic method using a Dionex AS11 system for the determination of low molecular weight dicarboxylic acids (low-M_w DCAs) in background atmospheric aerosol. Interference with the oxalic acid peak from sulfate in background PM_2.5 aerosol, 15.8 times the oxalic acid concentration, was remedied by removing sulfate using a barium cartridge, whilst interference with the malonic acid peak from carbonate was reduced by using a carbonate removal device. An alternative remedy to sulfate interference was use of an AS14 system using isocratic eluent, and this produced good resolution of oxalic acid from a high sulfate peak. In both the AS11 and the AS14 system, linear correlation coefficients were at all times >0.9990 with excellent linear range, the recoveries ranged from 92.8 to 106%, with relative standard deviation of 3.67-6.30%, whilst method detection limits (MDLs) ranged from 0.36 μg L⁻¹ for malic acid to 3.87 μg L⁻¹ for maleic acid. These data indicate that the analytical methods developed herein produce excellent separation efficiency and good determination of low-M_w DCAs with satisfactory accuracy, recoveries, and MDLs. Samples left at room temperature (20 °C) for 300 min in a simulation of the ‘waiting time’ involved in the proposed IC analysis decayed to between 86% (oxalic acid) and 39% (succinic and malonic acids) of their original concentration, whilst at 4 °C concentrations remained at 96-101% of original, indicating that maintaining samples at a low temperature prior to injection into the IC analyzer is vital for obtaining accurate results when analyzing low-M_w DCAs. Oxalic acid was found to be the most prevalent low-M_w DCA in background aerosol, comprising 57% of the total low-M_w DCAs and 0.959% of the PM_2.5 aerosol mass, followed by succinic acid and malonic acid.     

Peak parking technique for the simultaneous determination of anions and cations

An ion chromatography method is described for the simultaneous determination of anions (Cl^–, NO₃^–, and SO₄^2–) and cations (Na⁺, NH₄⁺, K⁺, Mg²⁺, and Ca²⁺) using a single pump, a single eluent and a single detector. An anion-exchange column modified with chondroitin sulfate C facilitated the elution of the above three anions using 5 mM tartaric acid as the eluent in isocratic mode, whereas the same eluent facilitated the separation of the above five cations on a commercially-available cation-exchange column. The separation columns were connected in series via two six-port switching valves, so the required cation-exchange or anion-exchange separation could be carried out by selecting the appropriate positions for the switching valves. The separations were completed in 30 min.     

Determination of itopride in human plasma by liquid chromatography coupled to tandem mass spectrometric detection: application to a bioequivalence study

A simple method using a one-step liquid-liquid extraction (LLE) with butyl acetate followed by high-performance liquid chromatography (HPLC) with positive ion electrospray ionization tandem mass spectrometric (ESI-MS/MS) detection was developed for the determination of itopride in human plasma, using sulpiride as an internal standard (IS). Acquisition was performed in multiple reaction monitoring (MRM) mode, by monitoring the transitions: m/z 359.5 > 166.1 for itopride and m/z 342.3 > 111.6 for IS, respectively. Analytes were chromatographed on an YMC C₁₈ reverse-phase chromatographic column by isocratic elution with 1 mM ammonium acetate buffer-methanol (20: 80, v/v; pH 4.0 adjusted with acetic acid). Results were linear (r² = 0.9999) over the studied range (0.5-1000 ng mL⁻¹) with a total analysis time per run of 2 min for LC-MS/MS. The developed method was validated and successfully applied to bioequivalence studies of itopride hydrochloride in healthy male volunteers.     

Compact type-I coil planet centrifuge for counter-current chromatography

A compact type-I coil planet centrifuge has been developed for performing counter-current chromatography. It has a revolution radius of 10 cm and a column holder height of 5 cm compared with 37 and 50 cm in the original prototype, respectively. The reduction in the revolution radius and column length permits application of higher revolution speed and more stable balancing of the rotor which leads us to learn more about its performance and the future potential of type-I coil planet centrifuge. The chromatographic performance of this apparatus was evaluated in terms of retention of the stationary phase (S_f), peak resolution (R_s), theoretical plate (N) and peak retention time (t_R). The results of the experiment indicated that increasing the revolution speed slightly improved both the retention of the stationary phase and the peak resolution while the separation time is remarkably shortened to yield an excellent peak resolution at a revolution speed of 800 rpm. With a 12 ml capacity coiled column, DNP-DL-glu, DNP-β-ala and DNP-l-ala were resolved at R_s of 2.75 and 2.16 within 90 min at a flow rate of 0.4 ml/min. We believe that the compact type-I coil planet centrifuge has a high analytical potential.     

Characterization of new types of stationary phases for fast and ultra-fast liquid chromatography by signal processing based on AutoCovariance Function: A case study of application to Passiflora incarnata L. extract separations

In this study, a comparative investigation was performed of HPLC Ascentis^® (2.7 μm particles) columns based on fused-core particle technology and Acquity^® (1.7 μm particles) columns requiring UPLC instruments, in comparison with Chromolith™ RP-18e columns. The study was carried out on mother and vegetal tinctures of Passiflora incarnata L. on one single or two coupled columns. The fundamental attributions of the chromatographic profiles are evaluated using a chemometric procedure, based on the AutoCovariance Function (ACVF). Different chromatographic systems are compared in terms of their separation parameters, i.e., number of total chemical components (m_tot), separation efficiency (σ), peak capacity (n_c), overlap degree of peaks and peak purity. The obtained results show the improvements achieved by HPLC columns with narrow size particles in terms of total analysis time and chromatographic efficiency: comparable performance are achieved by Ascentis^® (2.7 μm particle) column and Acquity^® (1.7 μm particle) column requiring UPLC instruments. The ACVF plot is proposed as a simplified tool describing the chromatographic fingerprint to be used for evaluating and comparing chemical composition of plant extracts by using the parameters D% – relative abundance of the deterministic component – and c_EACF – similarity index computed on ACVF.     

Online photocatalytic device for highly selective pre-column fluorescence derivatization of 5-hydroxyindoles with benzylamine

A fluorimetric liquid chromatographic method for the determination of 5-hydroxyindoles based on the benzylamine derivatization process mediated through an online photocatalytic oxidation has been developed. In this study, we used a photocatalytic column comprising tefzel tubing packed with TiO₂-coated glass beads, as a pre-column derivatization reactor. The fluorescence derivatization of 5-hydroxyindoles using benzylamine proceeded during their passage through the reaction column under near-UV irradiation. The 5-hydroxyindole derivatives were separated continuously on a reversed-phase liquid chromatography within 50 min, using 100 mM acetate buffer (pH 4.6)-acetonitrile (72:28, v/v; isocratic elution) containing 3 mM sodium octanesulfonate; the samples were detected fluorimetrically at 465 nm upon excitation at 350 nm. The detection limits (signal-to-noise ratio = 3) of the 5-hydroxyindoles were in the range from 160 to 360 fmol per 5 μL injection. We have applied this method, which requires minimal sample pre-treatment, to the determination of 5-hydroxyindole-3-acetic acid in human urine.     

Single-run ion chromatographic separation of inorganic and low-molecular-mass organic anions under isocratic elution: Application to environmental samples

For the isocratic ion chromatography (IC) separation of low-molecular-mass organic acids and inorganic anions three different anion-exchange columns were studied: IonPac AS14 (9 μm particle size), Allsep A-2 (7 μm particle size), and IC SI-50 4E (5 μm particle size). A complete baseline separation for all analyzed anions (i.e., F⁻, acetate, formate, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻ and SO₄²⁻) in one analytical cycle of shorter than 17 min was achieved on the IC SI-50 4E column, using an eluent mixture of 3.2 mM Na₂CO₃ and 1.0 mM NaHCO₃ with a flow rate of 1.0 mL min⁻¹. On the IonPac AS14 column, it was possible to separate acetate from inorganic anions in one run (i.e., less than 9 min), but not formate, under the following conditions: 3.5 mM Na₂CO₃ plus 1.0 mM NaHCO₃ with a flow rate of 1.2 mL min⁻¹. Therefore, it was necessary to adapt a second run with a 2.0 mM Na₂B₄O₇ solution as an eluent under a flow rate of 0.8 mL min⁻¹ for the separation of organic ions, which considerably enlarged the analysis time. For the Allsep A-2 column, using an eluent mixture of 1.2 mM Na₂CO₃ plus 1.5 mM NaHCO₃ with a flow rate of 1.6 mL min⁻¹, it was possible to separate almost all anions in one run within 25 min, except the fluoride-acetate critical pair. A Certified Multianion Standard Solution PRIMUS for IC was used for the validation of the analytical methods. The lowest RSDs (less than 1%) and the best LODs (0.02, 0.2, 0.16, 0.11, 0.06, 0.05, 0.04, 0.14 and 0.09 mg L⁻¹ for F⁻, Ac⁻, For⁻, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻ and SO₄²⁻, respectively) were achieved using the IC SI-50 4E column. This column was applied for the separation of concerned ions in environmental precipitation samples such as snow, hail and rainwater.     

Simple automated generation of gradient elution conditions in sequential injection chromatography using monolithic column

The paper deals with the concept of simple automated creation of gradient profile of the mobile phase for gradient-elution sequential injection chromatography (GE-SIC). The feasibility and merits of this concept are demonstrated on the separation and simultaneous assay of indomethacin as active principle and of its two degradation products (5-methoxy-2-methylindoleacetic acid and 4-chloro-benzoic acid) in a topical pharmaceutical formulation.The GE-SIC separation was performed with a FIAlab^® 3000 SIC set-up (USA) equipped with an Onyx™ Monolithic C18 (25 mm × 4.6 mm, Phenomenex^®) column, a six-port selection valve, a 5-mL syringe pump and a fiber-optics UV CCD detector. Ketoprofen was used as an internal standard (IS). The gradient elution was achieved by automated reproducible mixing of acetonitrile and aqueous 0.2% phosphoric acid in the holding coil of the SIC system. Different profiles of the gradient elution were tested. The optimal gradient using two mobile phases 30:70 and 50:50 of acetonitrile/0.2% phosphoric acid (v/v) was achieved under the optimum flow rate 1.2 mL min⁻¹. The chromatographic resolution R between the peaks of all solutes (including the IS) was >2.00. The repeatability of retention times was characterized by the RSD values 0.18-0.30% (n = 6). Net separation time was 3.5 min and the mobile phase consumption was 4.5 mL for a single GE-SIC assay. The figures of merit of the novel GE-SIC method compared well with those of conventional HPLC.     

High Performance Liquid Chromato-Graphic Assay For 5-Fluorouracil and 5-Fluorocytosine

Abstract

A high performance liquid chromatographic assay for separating 5-fluorouracil and 5-fluorocytosine in the presence of potential decomposition products urea, barbituric acid, uracil 6-hydroxycytosine, and cytosine was developed.

It was found that ion-pair chromatography using a reversephase C18 column, 0.46 cm i.d. by 15 cm in length, employing gradient elution was satisfactory for separating the various compounds, however, isocratic elution was more appropriate for determining the concentration of the two drugs in the presence of their actual decomposition products.

The mobile phase for isocratic elution was 85% aqueous phosphate buffer pH 2.1 and 15% methanol containing 0.0025 M pentane and heptane sulfonic acid sodium salts delivered at 1.0 mllmin. The eluent was monitored at 254 and 285 nm as all compounds do not absorb strongly at a single wavelength. A linear relationship was obtained for the peak height ratio for both 5-fluorouracil and 5-fluorocytosine against 5-methylcytosine, the internal standard over the range 0.125 to 1.000 × ? 10^?4 M ₀     

Isocratic and gradient elution chromatography: a comparison in terms of speed, retention reproducibility and quantitation

Chromatographers are cautioned to avoid gradient elution when isocratic elution will do. In this work, we compared the analytical properties of gradient and isocratic separations of a sample which can be done quite readily under isocratic conditions. We found that gradient elution gave a shorter overall analysis with similar resolution of the critical pair compared to isocratic elution without sacrificing repeatability in retention time, peak area and peak height or linearity of the calibration curve. We also obtained acceptable repeatability in peak area/height and linearity of calibrations curves for a sample that required gradient elution using a practical baseline subtraction technique. Based on these results and related work which show that columns can be reequilibrated by flushing with less than two column volumes of the initial eluent, we conclude that many of the reasons given to avoid gradient elution deserve serious reconsideration, especially for those samples which are easily separated isocratically. However, we believe isocratic elution will remain preferable when: (1) the sample contains less than 10 weakly retained components (i.e. the last peak elutes with k' < 5) or (2) the gradient baseline impedes trace analysis.     

Nanogold-actuated biomimetic peroxidase for sensitized electrochemical immunoassay of carcinoembryonic antigen in human serum

We present a method for the simultaneous determination of guanidinosuccinic acid (GSA) and guanidinoacetic acid (GAA) from urine by protein precipitation and liquid chromatography/tandem mass spectrometry. The chromatographic separation was performed using a cation exchange column with an elution gradient of 0.1 mM and 20 mM ammonium acetate buffers. GSA was detected with the mass spectrometer in negative ion mode monitoring at m/z 174.1, and GAA, creatinine, arginine, and homoarginine were in positive ion mode monitoring at m/z 118.1, 114.1, 175.1, and 189.1, respectively. As an internal standard, l-arginine-¹³C₆ hydrochloride and creatinine-d₃ (methyl-d₃) were used. The calibration ranges were 0.50-25.0 μg mL⁻¹, and good linearities were obtained for all compounds (r > 0.999). The intra- and inter-assay accuracies (expressed as recoveries) and precisions at three concentration levels (1.00, 5.00 and 25.0 μg mL⁻¹) were better than 83.8% and 7.41%, respectively. The analytical performance of the method was evaluated by determination of the compounds in urine from male C57BL/J Iar db/db diabetes mellitus (DM) mice. The values of GSA and GAA corrected by the ratios of the individual compounds to creatinine were significantly increased in DM mice compared with control mice. These results indicated that the newly developed method was useful for determining urinary guanidino compounds and metabolites of arginine.