The effect of a wake-mounted splitter plate on the flow around a surface-mounted finite-height circular cylinder

The influence of a wake-mounted splitter plate on the flow around a surface-mounted circular cylinder of finite height was investigated experimentally using a low-speed wind tunnel. The experiments were conducted at a Reynolds number of Re=7.4×10⁴ for cylinder aspect ratios of AR=9, 7, 5 and 3. The thickness of the boundary layer on the ground plane relative to the cylinder diameter was δ/D=1.5. The splitter plates were mounted on the wake centreline with negligible gap between the base of the cylinder and the leading edge of the plate. The lengths of the splitter plates, relative to the cylinder diameter, ranged from L/D=1 to 7, and the plate height was always equal to the cylinder height. Measurements of the mean drag force coefficient were obtained with a force balance, and measurements of the vortex shedding frequency were obtained with a single-component hot-wire probe situated in the wake of the cylinder–plate combination. Compared to the well-studied case involving an infinite circular cylinder, the splitter plate was found to be a less effective drag-reduction device for finite circular cylinders. Significant reduction in the mean drag coefficient was realized only for the finite circular cylinder of AR=9 with intermediate-length splitter plates of L/D=1–3. The mean drag coefficients of the other cylinders were almost unchanged. In terms of its effect on vortex shedding, a splitter plate of sufficient length was able to suppress Kármán vortex shedding for all of the finite circular cylinders tested. For AR=9, vortex shedding suppression occurred for L/D≥5, which is similar to the case of the infinite circular cylinder. For the smaller-aspect-ratio cylinders, however, the splitter plate was more effective than what occurs for the infinite circular cylinder: for AR=3, vortex shedding suppression occurred for all of the splitter plates tested (L/D≥1); for AR=5 and 7, vortex shedding suppression occurred for L/D≥1.5.     

Influence of aspect ratio on the mean flow field of a surface-mounted finite-height square prism

The flow around surface-mounted, finite-height square prisms at a Reynolds number of Re = 4.2 × 10⁴ was investigated experimentally in a low-speed wind tunnel using particle image velocimetry. The thickness of the boundary layer on the ground plane relative to the width of the prism was δ/D = 1.5. Four prism aspect ratios were tested, AR = 9, 7, 5, and 3, to study how the aspect ratio influences the flow field close to the prism. Upstream of the prism, lowering the aspect ratio from AR = 9 to AR = 3 causes the stagnation point on the upstream face to move closer to the free end, but there is no influence on the location and strength of the horseshoe vortex. Lowering the aspect ratio from AR = 9 to AR = 3 causes the cross-stream vortices in the upper and lower halves of the wake to move downstream and upstream, respectively; the latter vortex is absent for AR = 3, suggesting this prism sits below the critical aspect ratio. Above the free end of the prism, within the region of separated flow, lowering the aspect ratio from AR = 9 to AR = 3 shifts the location of the cross-stream vortex farther downstream. For the prism of AR = 3, reverse flow above the free end is stronger yet more unsteady compared to the more slender prisms, while the streamwise edge vortices are smaller and weaker.     

Aerodynamic forces and three-dimensional flow structures in the mean wake of a surface-mounted finite-height square prism

Different flow models have been proposed for the flow around surface-mounted finite-height square prisms, but there is still a lack of consensus about the origin and connection of the streamwise tip vortices with the other elements of the wake. This numerical study was performed to address this gap, in addition to clarifying the relationship of the near-wake structures with the far wake and the near-wall flow, which is associated with the fluid forces. A large-eddy simulation approach was adopted to solve the flow around a surface-mounted finite-height square prism with an aspect ratio of AR = 3 and a Reynolds number Re = 500. The mean drag and normal forces and the bending moment for the prism were quantitatively compared in terms of skin-friction and pressure contributions, and related to the near-wall flow. Both three-dimensional visualizations and planar projections of the time-averaged flow field were used to identify, qualitatively, the main structures of the wake, including the horseshoe vortex, corner vortices and regions of high streamwise vorticity in the upper part of the wake. These features showed the same qualitative behavior as reported in high Reynolds number studies. It was found that some regions of high streamwise vorticity magnitude, like the tip vortices, are associated with the three-dimensional bending of the flow, and the tip vortices did not continuously extend to the free end of the prism. The three-dimensional flow analysis, which integrated different observations of the flow field around surface-mounted finite-height square prisms, also revealed that the mean near-wake structure is composed of two sections of different origin and location of dominance.     

The effect of incidence angle on the mean wake of surface-mounted finite-height square prisms

The mean wake of a surface-mounted finite-height square prism was studied experimentally in a low-speed wind tunnel to explore the combined effects of incidence angle (α) and aspect ratio (AR). Measurements of the mean wake velocity field were made with a seven-hole pressure probe for finite square prisms of AR = 9, 7, 5 and 3, at a Reynolds number of Re = 3.7 × 10⁴, for incidence angles from α = 0° to 45°. The relative thickness of the boundary layer on the ground plane, compared to the prism width, was δ/D = 1.5. As the incidence angle increases from α = 0° to 15°, the mean recirculation zone shortens and the mean wake shifts in the direction opposite to that of the mean lift force. The downwash is also deflected to this side of the wake and the mean streamwise vortex structures in the upper part of the wake become strongly asymmetric. The shortest mean recirculation zone, and the greatest asymmetry in the mean wake, is found at the critical incidence angle of α_critical ≈ 15°. As the incidence angle increases from α = 15° to 45°, the mean recirculation zone lengthens and the mean streamwise vortex structures regain their symmetry. These vortices also elongate in the wall-normal direction and become contiguous with the horseshoe vortex trailing arms. The mean wake of the prism of AR = 3 has some differences, such as an absence of induced streamwise vorticity near the ground plane, which support its classification as lying below the critical aspect ratio for the present flow conditions.     

Effects of aspect ratio and orientation on the wake characteristics of low Reynolds number flow over a triangular prism

The wake characteristics of unconfined flows over triangular prisms of different aspect ratios have been numerically analysed in the present work. For this purpose, a fixed Cartesian-grid based numerical technique that involves the porous medium approach to mimic the effect of solid blockage has been utilised. Correspondingly, laminar flow simulations ranging from the sub-critical regime (before the onset of vortex shedding) to the super-critical regime have been considered here within the limits of two-dimensionality. In the sub-critical regime, correlations relating the wake bubble length with Reynolds number (Re) have been proposed for various aspect ratios. Also, the effects of aspect ratio and Reynolds Number on the drag force coefficient (C_D) have been characterised for two different geometrical orientations of the prism (base or apex facing the flow). Subsequently, the critical Reynolds number at the onset of vortex shedding has been predicted for each of the aspect ratio considered, by an extrapolation procedure. The unsteady flow characteristics of the super-critical regime are finally highlighted for different aspect ratios and triangular orientations considered in the study.     

Experimental study on the flow regimes past a confined prism undergoing self-sustained oscillations

An experimental study based on Particle Image Velocimetry (PIV) is presented with the objective of studying the flow regimes that appear in the flow past a confined prism undergoing self-sustained oscillations at low Reynolds numbers (Re). The square-section prism, placed inside a 3D square cross-section vertical channel with a confinement ratio of 1/2.5, was tethered to the channel walls and, therefore, it was allowed to move freely transverse to the incoming flow. Re (based on the prism cross-section height) was varied in the range from 100 to 700. Three different prism to fluid density ratios (m¹) were considered: 0.56, 0.70, and 0.91. These two parameters, Re and m¹, were used to map the results obtained. In particular, it was found that five different regimes appear: (1) steady prism with steady recirculation bubble, (2) steady prism with unsteady vortex shedding wake, (3) large amplitude low frequency oscillating prism with unsteady vortex shedding wake, (4) small amplitude high frequency oscillating prism with unsteady vortex shedding wake, and (5) irregular/chaotic motion of both the prism and the wake. The PIV results and associated numerical simulations were used to analyze the different prism and wake states.     

On vortex shedding from low aspect ratio dual step cylinders

A dual-step cylinder is comprised of two cylinders of different diameters. A large diameter cylinder (D) with low aspect ratio (L/D) is attached to the mid-span of a small diameter cylinder (d). The present study investigates the effect of Reynolds number (Re_D) and L/D on dual step cylinder wake development for D/d=2, 0.2≤L/D≤3, and two Reynolds numbers, Re_D=1050 and 2100. Experiments have been performed in a water flume facility utilizing flow visualization, Laser Doppler Velocimetry (LDV), and Particle Image Velocimetry (PIV). The results show that vortex shedding occurs from both the large and small diameter cylinders for 1≤L/D≤3 at Re_D=2100 and 2≤L/D≤3 at Re_D=1050. At these conditions, large cylinder vortices predominantly form vortex loops in the wake and small cylinder vortices form half-loop vortex connections. At lower aspect ratios, vortex shedding from the large cylinder ceases, with the dominant frequency in the large cylinder wake attributed to the passage of vortex filaments connecting small cylinder vortices. At these lower aspect ratios, the presence of the large cylinder induces periodic vortex dislocations. Increasing L/D increases the frequency of occurrence of vortex dislocations and decreases the dominant frequency in the large cylinder wake. The identified changes in wake topology are related to substantial variations in the location of boundary layer separation on the large cylinder, and, consequently, changes in the size of the vortex formation region. The results also show that the Reynolds number has a substantial effect on wake vortex shedding frequency, which is more profound than that expected for a uniform cylinder.     

Investigation of passive oscillations of flexible splitter plates attached to a circular cylinder

This paper presents a numerical study to address wake control of a circular cylinder subjected to two-dimensional laminar flow regime using single and multiple flexible splitter plates attached to the cylinder. Three different cases are presented in the study, covering cylinders with one, two and three horizontally attached splitter plates while the locations of the plates around the cylinders are varied. The length of the splitter plates was equal to the cylinder diameter and Reynolds number was 100. Due to the flexibility of the plates, the problem was modeled as a Fluid–Structure Interaction (FSI) problem and the commercial finite element software, Comsol Multiphysics, was utilized to solve this problem using Arbitrary Lagrangian–Eulerian (ALE) method. Vortex shedding frequency and fluid forces acting on the cylinder are investigated, along with a comprehensive parametric study to identify the optimum arrangement of the plates for maximum drag reduction and maximum vortex shedding frequency reduction. The numerical results associated to the flexible splitter plates are also compared with the corresponding rigid splitter plate cases investigated in a previous study. Moreover, the tip amplitude of the plates and the maximum strains were measured in order to find an optimum position for placing a piezoelectric polymer to harvest energy from the flow.     

Effect of velocity ratio on the streamwise vortex structures in the wake of a stack

The time-averaged velocity and streamwise vorticity fields within the wake of a stack were investigated in a low-speed wind tunnel using a seven-hole pressure probe. The experiments were conducted at a Reynolds number, based on the stack external diameter, of Re_D=2.3×10⁴. The stack, of aspect ratio AR=9, was mounted normal to a ground plane and was partially immersed in a flat-plate turbulent boundary layer, where the ratio of the boundary layer thickness to the stack height was δ/H≈0.5. The jet-to-cross-flow velocity ratio was varied from R=0 to 3, which covered the downwash, crosswind-dominated and jet-dominated flow regimes. In the downwash and crosswind-dominated flow regimes, two pairs of counter-rotating streamwise vortex structures were identified within the stack wake. The tip vortex pair located close to the free end of the stack, and the base vortex pair located close to the ground plane within the flat-plate boundary layer, were similar to those found in the wake of a finite circular cylinder, and were associated with the upwash and downwash flow fields within the stack wake, respectively. In the jet-dominated flow regime, a third pair of streamwise vortex structures was observed, referred to as the jet-wake vortex pair, which occurred within the jet-wake region above the free end of the stack. The jet-wake vortex pair had the same orientation as the base vortex pair and was associated with the jet rise. The peak vorticity and strength of the streamwise vortex structures were functions of the jet-to-cross-flow velocity ratio. For the tip vortex structures, their peak vorticity and strength reduced as the jet-to-cross-flow velocity ratio increased.     

Aerodynamic flow vectoring of a wake using asymmetric synthetic jet actuation

This paper reports an experimental investigation on the wake of a blunt-based, flat plate subjected to aerodynamic flow vectoring using asymmetric synthetic jet actuation. Wake vectoring was achieved using a synthetic jet placed at the model base 2.5?mm from the upper corner. The wake Reynolds number based on the plate thickness was 7,200. The synthetic jet actuation frequency was selected to be about 75?% the vortex shedding frequency of the natural wake. At this actuation frequency, the synthetic jet delivered a periodic flow with a momentum coefficient, C _??, of up to 62?%. Simultaneous measurements of the streamwise and transverse components of the velocity were performed using particle image velocimetry (PIV) in the near wake. The results suggested that for significant wake vectoring, vortex shedding must be suppressed first. Under the flow conditions cited above, C _?? values in the range of 10?C20?% were required. The wake vectoring angle seemed to asymptote to a constant value of about 30° at downstream distances, x/h, larger than 4 for C _?? values ranging between 24 and 64?%. The phase-averaged vorticity contours and the phase-averaged normal lift force showed that most of the wake vectoring is produced during the suction phase of the actuation, while the blowing phase was mostly responsible for vortex shedding suppression.     

Flow around impulsively started square prisms

The flow around square and diamond prisms and a circular cylinder impulsively set into motion was studied experimentally using the particle image velocimetry (PIV) technique. The experiments were conducted in water in an X-Y towing tank for Reynolds numbers from Re=200-1000. The temporal development of the near-wake recirculation zone, and its pair of primary eddies, was examined from the initial start until the wake became asymmetric, at a dimensionless elapsed time of t^?=4 or 5. For both bodies, the length of the recirculation zone, the streamwise location of the primary eddies, and the strength of the primary eddies increased with time following the impulsive start, while the cross-stream spacing of the eddy centres remained nearly constant. The recirculation zones of the square and diamond prisms were longer than that of the impulsively started circular cylinder. For t^?>2, the primary eddy strength, maximum vorticity, and cross-stream spacing of the primary eddies, were the same for both the square prism and circular cylinder. The diamond prism had the strongest primary eddies and highest maximum values of vorticity. A comparison of recirculation zone length data for impulsively started bluff bodies of six different cross-sections illustrated the effects of afterbody and forebody shape, with the normal flat plate (no afterbody and no forebody) having the longest recirculation zone and the circular cylinder (rounded afterbody and rounded forebody) having the shortest recirculation zone.     

Low Reynolds number flow over a square cylinder with a detached flat plate

A numerical study of the alteration of a square cylinder wake using a detached downstream thin flat plate is presented. The wake is generated by a uniform flow of Reynolds number 150 based on the side length of the cylinder, D. The sensitivity of the near wake structure to the downstream position of the plate is investigated by varying the gap distance (G) along the wake centerline in the range 0 ⩽ G ⩽ 7D for a constant plate length of L = D. A critical gap distance is observed to occur at G_c ≈ 2.3D that indicates the existence of two flow regimes. Regime I is characterised by vortex formation occurring downstream of the gap while for regime II, formation occurs within the gap. By varying the plate length and gap distance, a condition is found where significant unsteady total lift reduction can occur. The root mean square lift reduction is limited by an unsteady stall process on the plate.     

Near-wake flow characteristics of a circular cylinder close to a wall

Flow characteristics in the near wake of a circular cylinder located close to a fully developed turbulent boundary layer are investigated experimentally using particle image velocimetry (PIV). The Reynolds number based on the cylinder diameter (D) is 1.2×10⁴ and the incident boundary layer thickness (δ) is 0.4D. Detailed velocity and vorticity fields in the wake region (0<x/D<6) are given for various gap heights (S) between the cylinder and the wall, with S/D ranging from 0.1 to 1.0. Both the ensemble-averaged (including the mean velocity vectors and Reynolds stress) and the instantaneous flow fields are strongly dependent on S/D. Results reveal that for S/D⩾0.3, the flow is characterized by the periodic, Kármán-like vortex shedding from the upper and lower sides of the cylinder. The shed vortices and their evolution are revealed by analyzing the instantaneous flow fields using various vortex identification methods, including Galilean decomposition of velocity vectors, calculation of vorticity and swirling strength. For small and intermediate gap ratios (S/D⩽0.6), the wake flow develops a distinct asymmetry about the cylinder centreline; however, some flow quantities, such as the Strouhal number and the convection velocity of the shed vortex, keep roughly constant and virtually independent of S/D.     

Instantaneous flow field above the free end of finite-height cylinders and prisms

The flow above the free ends of surface-mounted finite-height circular cylinders and square prisms was studied experimentally using particle image velocimetry (PIV). Cylinders and prisms with aspect ratios of AR = 9, 7, 5, and 3 were tested at a Reynolds number of Re = 4.2 × 10⁴. The bodies were mounted normal to a ground plane and were partially immersed in a turbulent zero-pressure-gradient boundary layer, where the boundary layer thickness relative to the body width was δ/D = 1.6. PIV measurements were made above the free ends of the bodies in a vertical plane aligned with the flow centreline. The present PIV results provide insight into the effects of aspect ratio and body shape on the instantaneous flow field. The recirculation zone under the separated shear layer is larger for the square prism of AR = 3 compared to the more slender prism of AR = 9. Also, for a square prism with low aspect ratio (AR = 3), the influence of the reverse flow over the free end surface becomes more significant compared to that for a higher aspect ratio (AR = 9). For the circular cylinder, a cross-stream vortex forms within the recirculation zone. As the aspect ratio of the cylinder decreases, the reattachment point of the separated flow on the free end surface moves closer to the trailing edge. For both the square prism and circular cylinder cases, the instantaneous velocity vector field and associated in-plane vorticity field revealed small-scale structures mostly generated by the separated shear layer.     

Fluid–structure interaction of a splitter plate in a convergent channel

The fluid–structure interaction (FSI) of a splitter plate in a convergent channel flow is studied by measuring both the flow field and the plate vibration. Particle Image Velocimetry (PIV) measurements show that the wake generated by the plate is characterized by cellular vortex shedding. Mean and RMS velocities presented in the plane normal to the main flow direction visualize clearly the cellular structure and related secondary flows. To evaluate the energy and spatial organization of the vortex shedding, spectral and correlation estimation methods are adapted to the PIV data. By presenting the spanwise variation of the streamwise spectra along the trailing edge, the nature of the cellular vortex shedding becomes evident. 2D space-correlation function reveals that the shedding in two neighboring cells occurs in a 180-degree phase shift. The vibration of the plate is studied with Digital Imaging (DI) and Laser Vibrometer (LV). The DI is based on images measured by the PIV system. An image-processing algorithm is used to detect the plate tip location and velocity simultaneously with the estimation of the fluid velocity field. The LV is used for the time-resolved measurement of the plate vibration. The results show that the plate vibrates in a very distinct mode characterized by a spanwise standing wave along the plate-trailing edge. This mode, in turn, causes the cellular vortex shedding.     

Unsteady near wake of a flat disk normal to a wall

The unsteady wake of a flat disk (diameter D) located at a distance of H from a flat plate has been experimentally investigated at a Reynolds number Re _D  = 1.3 × 10⁵. Tests have been performed for a range of gap ratio (H/D), spanning from 0.3 to 1.75. The leading edge of the flat plate is either streamlined (elliptical) or blunt (square). These configurations have been studied with PIV, high speed PIV and multi-arrayed off-set fluctuating pressure measurements. The results show a progressive increase of the complexity of the flow and of the interaction as the gap ratio decreases. For large values of H/D (1.75), the interaction is weak and the power spectral densities (PSD) exhibit a strong peak associated with the vortex shedding events (St = 0.131) – St = fD/U _∞ is the Strouhal number. For lower values of H/D (0.75), the magnitude of the wall fluctuating pressure increases significantly. A large band contribution is associated with the unsteady wake structure and turbulence. A slight increase of the shedding frequency (St = 0.145) is observed. A critical value of the gap ratio (about 0.35) has been determined. Below this critical value, a three-dimensional separated region is observed and the natural vortex shedding process is very strongly altered. These changes induce a great modification of the fluctuating pressure at the wall. Each interaction reacts in a different way to perturbed upstream conditions. In particular, the disk is an overwhelming perturbation for the lowest H/D value studied here and the relative influence of the upstream turbulence on the wall fluctuating pressure below the near wake region is moderate.     

Control of vortex shedding in an axisymmetric bluff body wake

In the present experimental study the effect of a control disc mounted at the rear of an axisymmetric blunt-based body of revolution, first studied by Mair, is investigated in the Reynolds number range 3×10³≤Re_D≤5×10⁴ . As the distance of the control disc from the blunt base is increased, four vortex shedding regimes are identified: at small distances there is no effect, then a sharp increase of vortex shedding activity and total drag is observed, followed by an interval with reduced activity and drag and finally at large distances a regime where the flow around the main body and disc become essentially independent, i.e. where the drag forces of the two elements become additive. The near and far wake velocity fields corresponding to the different regimes are documented with time- and phase-averaged hot-wire and LDA measurements, with spectral analysis of the data and with flow visualizations of the near wake. The results are used to develop an improved understanding of the instability mechanism leading to high vortex shedding activity.     

Wake transition for surface mounted rectangular cylinder due to incoming shear flow

Three-dimensional unsteady wake characteristics have been investigated numerically in flow past surface mounted finite-height rectangular cylinder using Open Source Field Operation and Manipulation. Effect of impinging shear (shear intensity, K) on transitional characteristics of wake flow has been studied using iso-Q surfaces for Reynolds number (Re) in the range from 150 to 250. Various flow regimes, such as steady flow, symmetric and asymmetric modes of vortex shedding have been identified based on the values of Re and K for different side ratios (SR) of the cylinder. Unsteady wake oscillations have been analyzed using time signal of transverse velocity component in the wake. These signals have been decomposed into different component signals using Hilbert-Huang transformation (HHT). Variation of frequency and energy density with time of the decomposed signals has been presented in the form of Hilbert spectra. Effects of Re, SR and K on wake oscillation frequency have been illustrated in the form of marginal spectra. Time-delay reconstructions and Poincare sections have been examined to study periodic and aperiodic nature of the wake flow. Non-stationarity associated with the wake fluctuation is quantified in terms of degree of stationarity. Symmetric and asymmetric modes have been confirmed using singular value decomposition of the vorticity field and presented using dynamic modes. Growth rate and frequency of the modes corresponding to symmetric shedding are found to be lower than those for asymmetric shedding. In addition, variation in mean drag coefficient has been reported with change in Re and K for each value of SR.     

Influence of rounding corners on the wake of a finite-length cylinder: An experimental study

This study aims to investigate experimentally the influence of rounding corners (r) as well as aspect ratio (AR) on the flow structures of a surface-mounted finite cylinder. The cylinders with sharp (r* = r/D = 0) and rounded corners (r*=0.167, 0.25 and 0.5) and aspect ratio or height-to-width/diameter ratio (AR = H/D) between 2 and 7 are utilized. The experiments are based on the five-hole probe and hot-wire measurements as well as the oil flow visualization. Wake measurements are made in an open return wind tunnel at the Reynolds number, Re = 1.6 × 10⁴, where Re is defined based on the side width/diameter (D) of the cylinder cross-section and the freestream velocity. It is found that r* and AR have significant effects on the flow structure from the perspective of wake topology, strength of streamwise vortices, and vortex shedding frequency. For all r* considered, the wake is characterized by a quadrupole type (both the tip and base vortices are present) at AR = 7, while a dipole type occurs for AR = 2 and 4 (the base vortices are absent). The strength (circulation) of the streamwise vortex structures is affected by r*. For all AR examined in the present study, the strengths of tip and base vortex structures decrease with increasing r*. The oil flow visualization demonstrates that the features of the horseshoe vortex are sensitive to r* and AR. With increasing r*, the location of the separation line moves downstream and the distance between horseshoe vortex legs decreases. Velocity measurements reveal that the downwash flow enhances with increasing r*. It is also found that the Strouhal number increases progressively by 60% as r* increases from 0 to 0.5, regardless of AR.