Uniform-sized silicone oil microemulsions: preparation, investigation of stability and deposition on hair surface

Emulsions are commonly used in foods, pharmaceuticals and home-personal-care products. For emulsion based products, it is highly desirable to control the droplet size distribution to improve storage stability, appearance and in-use property. We report preparation of uniform-sized silicone oil microemulsions with different droplets diameters (1.4-40.0 μm) using SPG membrane emulsification technique. These microemulsions were then added into model shampoos and conditioners to investigate the effects of size, uniformity, and storage stability on silicone oil deposition on hair surface. We observed much improved storage stability of uniform-sized microemulsions when the droplets diameter was ≤22.7 μm. The uniform-sized microemulsion of 40.0 μm was less stable but still more stable than non-uniform sized microemulsions prepared by conventional homogenizer. The results clearly indicated that uniform-sized droplets enhanced the deposition of silicone oil on hair and deposition increased with decreasing droplet size. Hair switches washed with small uniform-sized droplets had lower values of coefficient of friction compared with those washed with larger uniform and non-uniform droplets. Moreover the addition of alginate thickener in the shampoos and conditioners further enhanced the deposition of silicone oil on hair. The good correlation between silicone oil droplets stability, deposition on hair and resultant friction of hair support that droplet size and uniformity are important factors for controlling the stability and deposition property of emulsion based products such as shampoo and conditioner.     

Self-diffusion and collective diffusion of charged colloids studied by dynamic light scattering

A microemulsion of decane droplets stabilized by a nonionic surfactant film is progressively charged by substitution of a nonionic surfactant molecule by a cationic surfactant. We check that the microemulsion droplets remain identical within the explored range of volume fraction (0.02-0.18) and of the number of charges per droplet (0-40). We probe the dynamics of these microemulsions by dynamic light scattering. Despite the similar structures of the uncharged and charged microemulsions, the dynamics are very different. In the neutral microemulsion, the fluctuations of polarization relax, as is well-known, via the collective diffusion of the droplets. In the charged microemulsions, two modes of relaxation are observed. The fast one is ascribed classically to the collective diffusion of the charged droplets coupled to the diffusion of the counterions. The slow one has, to our knowledge, not been observed previously neither in similar microemulsions nor in charged spherical colloids. We show that the slow mode is also diffusive and suggest that its possible origin is the relaxation of local charge fluctuations via the local exchange of droplets bearing different numbers of charges. The diffusion coefficient associated with this mode is then the self-diffusion coefficient of the droplets.     

Multielement preconcentration of trace heavy metals in seawater with an emulsion containing 8-quinolinol for graphite-furnace atomic absorption spectrometry

A water-in-oil type emulsion containing 8-quinolinol has been used for the concentration of traces of heavy metals from seawater prior to their determinations by graphite-furnace atomic absorption spectrometry. The emulsion used was prepared by dissolving 40 mg of 8-quinolinol and 60 mg of sorbitan monooleate (Span-80) in 3.0 ml of toluene and vigorously mixing with 0.70 ml of aqueous hydrochloric acid solution (1.5 mol l⁻¹) by ultrasonic irradiation. The resulting emulsion was gradually injected into 100 ml of sample solution (pH 8.5) and dispersed by stirring as numerous tiny globules. Four heavy metals (Co, Ni, Cu, and Cd) in the sample solution were quantitatively transported through the organic layer into the acidic aqueous droplets encapsulated in the emulsion. After collecting the dispersed emulsion globules, they were demulsified by heating and the heavy metals in the segregated aqueous phase were determined by atomic absorption spectrometry. Owing to the highly efficient concentration (100-fold), these heavy metals at sub-ng ml⁻¹ levels in seawater were determined with satisfactory accuracy and precision, being confirmed with certified reference samples.     

Organic and bioorganic reactions in microemulsions

During the last two decades reactions in microemulsions have developed into an emerging technology. In most instances oil-continuous microemulsions (w/o systems) have been used and the water droplets have proven useful as “minireactors” for various types of syntheses. This review discusses recent advances in the fields of organic and bioorganic reactions in microemulsions. In preparative organic synthesis microemulsions are of interest to overcome incompatibility problems between nonpolar organic compounds and inorganic salts. For this purpose, microemulsions can be regarded as an alternative to two-phase systems with added phase transfer reagents. Properly formulated microemulsions may also accelerate organic reactions, various mechanisms of such rate enhancements are discussed. Transition from a homogeneous solvent system to a microemulsion may also affect the regioselectivity of organic reactions due to orientation of reactants at the oil-water interface. In bioorganic synthesis, microemulsions are of interest as a reaction medium for several reasons: (i) nonpolar substrates can be dissolved in high concentrations, (ii) thermodynamic equilibria of condensation/hydrolysis reactions can be shifted by adjusting water content, (iii) enzymes are sometimes found to be more stable and more active than in aqueous buffer. Lipases are the most widely used enzymes and reactions have been performed in different types of microemulsion systems. This review presents general aspects of enzymatic catalysis in microemulsions followed by a discussion of recent advances in preparative work focusing on lipase catalyzed processes.     

Studies on microemulsions

The microemulsions formed in the 4-component system water-potassium oleate-hexanol-dodecane have been investigated by time-average light scattering and small angle neutron scattering. A constant volume fraction ratio water: potassium oleate of 1.44 was used and at this constant composition, which gave a pseudo 3-component system, a wide region of the microemulsion domain was examined. In order to interpret the scattering data at finite volume fractions of the dispersed phase, water, allowance had to be made for interactions between the water-in-oil microemulsion droplets. This was carried out using a hard sphere model for the interaction. It is shown that using this model self-consistent results are obtained by light scattering and neutron scattering and an estimate can be made of the size of the particles in concentrated colloidal dispersions.     

Automatic microemulsion preparation for metals determination in fuel samples using a flow-batch analyzer and graphite furnace atomic absorption spectrometry

The principal thermodynamic advantages of using microemulsions over standard emulsions for flow metal analysis are the greatly increased analyte stability and emulsive homogeneity that improve both the ease of sample preparation, and the analytical result. In this study a piston propelled flow-batch analyzer (PFBA) for the determination of Cu, Cr and Pb in gasoline and naphtha by graphite furnace atomic absorption spectrometry (GF AAS) was explored. Investigative phase modeling for low dilution was conducted both for gasoline and naphtha microemulsions. Rheological considerations were also explored including a mathematical flow derivation to fine tune the system's operational parameters, and the GF AAS coupling. Both manual and automated procedures for microemulsion preparation were compared. The results of the paired t test at a 95% confidence level showed no significant differences between them. Further recovery test results confirmed a negligible matrix effect of the sample on the analyte absorption signals and an efficient stabilization of the samples (with metals) submitted to microemulsion treatment. The accuracy of the developed procedure was attested by good recovery percentages in the ranges of 100.0 ± 3.5% for Pb in the naphtha samples, and 100.2 ± 3.4% and 100.7 ± 4.6% for Cu and Cr, respectively in gasoline samples.     

Background and operating parameters in microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) is an electrodriven separation technique. Separations are generally achieved using microemulsions consisting of surfactant-coated nanometer-sized oil droplets suspended in aqueous buffer. A cosurfactant such as a short-chain alcohol is generally used to stabilize the microemulsion. This review summarizes the various microemulsion types and compositions that have been used in MEEKC. The effects of key-operating variables such as surfactant type and concentration, cosurfactant type and concentration, buffer pH and type, oil type and concentration, use of organic solvent and cyclodextrin additions, and temperature are described. Specific examples of water-in-oil microemulsions and chirally selective separations are also covered.     

The effect of cosurfactants and the initiator concentration on the polymer to surfactant concentration in nanolatexes

The effect of cosurfactant and initiator concentration on the ab initio production of nanolatexes using low surfactant levels was investigated. While the use of cosurfactants (acrylic acid and pentanol) increased the amount of monomer that can be used in styrene‐SDS microemulsion formulations to 13 wt %, high surfactant concentrations are still required, resulting in polymer‐to‐surfactant ratios (Pol/Surf) <1. Latexes with particle size of 30 ± 5 nm were produced upon polymerization of these microemulsions. The Pol/Surf can be significantly increased by increasing the initiator concentration of emulsion polymerization recipes. Particle sizes are comparable with microemulsion latexes, however, less surfactant is required. The reduction in the particle size with higher initiator concentration is attributed to a higher efficiency of particle nucleation and to a higher nucleation rate relative to the rate of monomer transfer. Nanolatexes (particle size < 30 nm) were obtained with 19 wt % solids content and Pol/Surf of 3.6 in ab initio. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Phase behavior and microstructure of C12E5 nonionic microemulsions with chlorinated oils

New non-ionic microemulsions consisting of pentaethyleneglycol dodecyl ether, water, and 1-chloroalkanes were prepared, and their phase behavior was studied. A homologous series of five different 1-chloroalkanes from 1-chlorooctane to 1-chlorohexadecane was studied. The phase behavior of the microemulsions was determined by vertical sections through the Gibbs' phase prism ("fish" plots), from which valuable information such as the microemulsion balance temperature (T(0)), efficiency of the surfactant (phi*), temperature extension of the three-body phase (DeltaT), mean temperature (T(m)), and the monomeric solubility in oil (phi(mon,oil)) was obtained. The chlorinated alkanes in the microemulsions shift the balance temperature to about 14 degrees C lower compared with their n-alkane counterparts. This indicates the polar nature of the chlorinated oils and their ability to penetrate the surfactant film. The chlorinated alkanes thus behave as short n-alkane molecules and lower the spontaneous curvature of the microemulsion droplets. The efficiency of the surfactant and the monomeric solubility in oil systematically depend on the alkyl chain length of the oil, with the efficiency and solubility decreasing with increasing alkyl chain length of 1-chloroalkane. The size and shape of the microemulsion droplets in the microemulsion phase were studied by small-angle X-ray scattering (SAXS). For a surfactant-to-oil volume fraction ratio of 0.80, the droplets can be described by ellipsoidal shapes, and the size of the droplets increased with increasing alkyl chain length.     

微乳剂低温稳定性的研究

微乳剂低温稳定性是微乳剂制剂质量技术指标之一.其影响因素主要为有机溶剂、表面活性剂、助溶剂和水质.以本文配制的几种农药微乳剂：2.5％吡虫啉、5％烯唑醇和10％哒螨灵微乳剂为研究对象，提出了微乳剂制剂存在有机溶剂中有效成分的稳定溶解突变点和添加表面活性剂应保持亲水性与亲油性平衡的观点.     

Kinetics of polymerization of styrene-in-water microemulsions

The kinetics of polymerization of styrene-in-water microemulsions was investigated using dilatometry. From plots of percentage conversion versus time, the rate of polymerization, R _p, was determined. From log-log plots of R _p versus styrene and initiator [2,2′-azobis(isobutyronitrile), AIBN] concentrations the following relationship was established: R _p∝ [styrene]^1.2 [AIBN]^0.46. These exponents are similar to those predicted by the theory of emulsion polymerization. The results also showed a rapid conversion in the initial period (interval 1) followed by a slower rate at longer times (interval 2). It was suggested that in interval 1, the main process in nucleation of the microemulsion droplets, whereas in interval 2 propagation is the more dominant factor. The rapid polymerization of microemulsions is consistent with their structure, whereby very small droplets with flexible interfaces are produced. Received: 2 March 1999 Accepted in revised form: 10 May 1999     

Determination of manganese in diesel,gasoline and naphtha by graphite furnace atomic absorption spectrometry using microemulsion medium for sample stabilization

The determination of Mn in diesel, gasoline and naphtha samples at µg L^− 1 level by graphite furnace atomic absorption spectrometry, after sample stabilization in a three-component medium (microemulsion) was investigated. Microemulsions were prepared by mixing appropriate volumes of sample, propan-1-ol and nitric acid aqueous solution, and a stable system was immediately and spontaneously formed. After multivariate optimization by central composite design the optimum microemulsion composition as well as the temperature program was defined. In this way, calibration using aqueous analytical solution was possible, since the same sensitivity was observed in the optimized microemulsion media and 0.2% v/v HNO₃. The use of modifier was not necessary. Recoveries at the 3 µg L^− 1 level using both inorganic and organic Mn standards spiked solutions ranged from 98 to 107% and the limits of detection were 0.6, 0.5 and 0.3 µg L^− 1 in the original diesel, gasoline and naphtha samples, respectively. The Mn characteristic mass 3.4 pg. Typical relative standard deviation (n = 5) of 8, 6 and 7% were found for the samples prepared as microemulsions at concentration levels of 1.3, 0.8, and 1.5 µg L^− 1, respectively. The total determination cycle lasted 4 min for diesel and 3 min for gasoline and naphtha, equivalent to a sample throughput of 7 h^− 1 for duplicate determinations in diesel and 10 h^− 1 for duplicate determinations in gasoline and naphtha. Accuracy was also assessed by using other method of analysis (ASTM D 3831-90). No statistically significant differences were found between the results obtained with the proposed method and the reference method in the analysis of real samples.     

Determination of avermectins in commercial formulations using microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) was developed for quantitative analysis of avermectins, such as abamectin, doramectin and ivermectin, in commercial formulations, using the microemulsion buffer containing a 50 mM phosphate buffer at pH 2.5, 1.1% (v/v) n-octane as oil droplets, 180 mM sodium dodecylsulphate as surfactant, 890 mM 1-butanol as co-surfactant and 30% (v/v) ethanol as organic co-solvent. High accuracy and precision of the method were obtained. The contents of avermectins in commercial formulations determined by MEEKC were found to be insignificantly different with those determined by high performance liquid chromatography (HPLC). Therefore, MEEKC can be used an alternative method to HPLC for quantitative determination of avermectins.     

Structure of biodiesel based bicontinuous microemulsions for environmentally compatible decontamination: A small angle neutron scattering and freeze fracture electron microscopy study

Most toxic industrial chemicals and chemical warfare agents are hydrophobic and can only be solubilized in organic solvents. However, most reagents employed for the degradation of these toxic compounds can only be dissolved in water. Hence, microemulsions are auspicious media for the decontamination of a variety of chemical warfare agents and pesticides. They allow for the solubilization of both the lipophilic toxics and the hydrophilic reagent. Alkyl oligoglucosides and plant derived solvents like rapeseed methyl ester enable the formulation of environmentally compatible bicontinuous microemulsions. In the present article the phase behavior of such a microemulsion is studied and the bicontinuous phase is identified. Small angle neutron scattering (SANS) and freeze fracture electron microscopy (FFEM) measurements are used to characterize the structure of the bicontinuous phase and allow for an estimation of the total internal interface. Moreover, also the influence of the co-surfactant (1-pentanol) on the structural parameters of the bicontinuous phase is studied with SANS.     

Characteristics of microemulsion polymerized styrene with water-soluble versus oil-soluble initiators

The effect of oil-soluble versus water-soluble free-radical generators in the polymerization of styrene in oil-in-water (O/W) micromulsions were investigated by photon correlation spectroscopy. The microemulsions were formed by styrene, brine, sodium dodecyl sulfate (SDS), and pentanol. The polymerizations were carried out in two microemulsions that contained droplets differing by a factor of 2.4 in volume. Under the conditions of ? = 0.019 and NaCl/SDS > 2 the microemulsions were stable and the droplets were independent of one another. Both oil-soluble and water-soluble initiators produced polystyrene that contained fractions of two different sizes. In the case of the oil-soluble initiator the droplet size in the microemulsion seemed to be correlated to the size of the product whereas in the case of the water-soluble initiator, there seemed to be little relation.     

Recent advances in microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) is an electrodriven separation technique. Separations are typically achieved using oil-in-water microemulsions, which are composed of nanometre-sized droplets of oil suspended in aqueous buffer. The oil droplets are coated in surfactant molecules and the system is stabilised by the addition of a short-chain alcohol cosurfactant. The novel use of water-in-oil microemulsions for MEEKC separations has also been investigated recently. This report summarises the different microemulsion types and compositions used to-date and their applications with a focus on recent papers (2002-2004). The effects of key operating variables (pH, surfactant, cosurfactant, oil phase, buffer, additives, temperature, organic modifier) and methodology techniques are described.     

Formation and characterization of microemulsions containing polymeric silicone

We have prepared microemulsions consisting of water/[40 wt % polyoxyethylene (20 mol) glycerin isostearate (abbreviated as POE-GIS) + 60 wt % random copolymer of polyoxyethylene (POE, 38 mol)/polyoxypropylene (POP, 10 mol) pentaerythritol tetramethyl ether {abbreviated as PEPTME (38/10)}]/[polyoxyethylene (POE, 19 mol)/polyoxypropylene (POP, 19 mol) polydimethylsiloxane copolymer (abbreviated as POE/POP-PDMS)] and water/[40 wt % POE-GIS + 60 wt % PEPTME (38/10)]/[95 wt % POE/POP-PDMS + 5 wt % oleic acid (abbreviated as OA)] systems and characterized them with optical observation, rheometry, and freeze-fracture transmission electron microscopy (FF-TEM) images. Bicontinuous and droplet-type O/W (oil-in-water) microemulsions are formed depending on the volume fraction of water. The bicontinuous structure observed in the oil-rich region, upon successive dilution with water, is transformed into a droplet-type microemulsion without phase separation.The prepared droplet-type microemulsion containing polymeric silicone and random copolymer PEPTME (38/10) as a cosurfactant in the water-rich region has potential applications in cosmetics.     

Microemulsions as reaction media for the synthesis of Pt nanoparticles

For the synthesis of Pt nanoparticles we used water-in-oil droplet microemulsions as templates. The focus was on the correlation between the size of the microemulsion droplets and that of the resulting Pt particles. To study this correlation in a systematic way, all particles were synthesized at the water emulsification failure boundaries where the microemulsion droplets are spherical and where their size can easily be tuned by the amount of added water. The metallic particles were synthesized by mixing two microemulsions one of which contains the metal salt H(2)PtCl(6) and the other the reducing agent NaBH(4). The size and structure of the microemulsion droplets was studied via small-angle X-ray scattering, while the Pt particles were characterized by high-resolution transmission electron microscopy in combination with energy-dispersive X-ray spectroscopy and selected area electron diffraction. The clear correlation between droplet and particle size was further supported by accompanying Monte Carlo simulations.     

Preparation and properties of Nafion/hollow silica spheres composite membranes

In present work, hollow silica spheres (HSS)/Nafion^® composite membranes were prepared by solution casting. The thermal properties, water retention, swelling behavior and proton conductivity of the composite membranes were explored. It was found that HSS dispersed well at micrometer scale in the obtained composite membranes by SEM and TEM observation. Thermal properties of composite membranes were improved than that of recast Nafion^® membrane. Compared with the recast Nafion^® membrane, the composite membranes showed higher water uptake and lower swelling degree at the temperature range from 40 to 100 °C. At the same HSS loading, the smaller the diameter of HSS in composite membranes, the more the water uptake, however, the swelling degree of composite membranes was increased. The proton conductivity of the composite membrane with 3–5 wt.% HSS (120 and 250 nm) increased distinctively at above 60 °C, reached the optimal value at 100 °C, and decreased slowly when the temperature exceeded 100 °C.