Polymer electrolyte membranes based on p‐toluenesulfonic acid doped poly(1‐vinyl‐1,2,4‐triazole): Synthesis,thermal and proton conductivity properties

Throughout this work, the synthesis, thermal as well as proton conducting properties of acid doped heterocyclic polymer were studied under anhydrous conditions. In this context, poly(1‐vinyl‐1,2,4‐triazole), PVTri was produced by free radical polymerization of 1‐vinyl‐1,2,4‐triazole with a high yield. The structure of the homopolymer was proved by FTIR and solid state ¹³C CP‐MAS NMR spectroscopy. The polymer was doped with p‐toluenesulfonic acid at various molar ratios, x = 0.5, 1, 1.5, 2, with respect to polymer repeating unit. The proton transfer from p‐toluenesulfonic acid to the triazole rings was proved with FTIR spectroscopy. Thermogravimetry analysis showed that the samples are thermally stable up to ～250 °C. Differential scanning calorimetry results illustrated that the materials are homogeneous and the dopant strongly affects the glass transition temperature of the host polymer. Cyclic voltammetry results showed that the electrochemical stability domain extends over 3 V. The proton conductivity of these materials increased with dopant concentration and the temperature. Charge transport relaxation times were derived via complex electrical modulus formalism (M*). The temperature dependence of conductivity relaxation times showed that the proton conductivity occurs via structure diffusion. In the anhydrous state, the proton conductivity of PVTri1PTSA and PVTri2PTSA was measured as 8 × 10^?4 S/cm at 150 °C and 0.012 S/cm at 110 °C, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1016–1021, 2010     

Proton conductivity survey of the acid doped copolymers based on 4‐vinylbenzylboronic acid and 4(5)‐vinylimidazole

In this work, poly(4‐vinylbenzylboronic acid‐co‐4(5)‐vinylimidazole) (poly(4‐VBBA‐co‐4‐Vim)) copolymers were synthesized by free‐radical copolymerization of the monomers 4‐VBBA and 4‐Vim at various monomer feed ratios. The copolymers were characterized by ¹H MAS NMR and ¹¹B MQ‐MAS NMR methods and the copolymer composition was determined via elemental analysis. The membrane properties of these copolymers were investigated after doping with phosphoric acid at several stoichiometric ratios. The proton exchange reaction between acid and heterocycle is confirmed by FTIR. Thermal properties of the samples were investigated via thermogravimetric analysis (TGA) and Differential scanning calorimetry (DSC). The morphology of the copolymers was characterized by x‐ray diffraction, XRD. The temperature dependence of proton conductivities of the samples was investigated by means of impedance spectroscopy. Proton conductivity of the copolymers increased with the doping ratio and reached to 0.0027 S/cm for poly(4‐VBBA‐co‐4‐Vim)/2H₃PO₄ in the anhydrous state. The boron coordination in the copolymer was determined by ¹¹B MQ‐MAS experiment and the coexistence of three and four coordinated boron sites was observed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1267–1274, 2009     

Anhydrous proton-conducting properties of triazole-phosphonic acid copolymers: a combined study with MAS NMR

The synthesis, thermal and proton conducting properties of copolymers based on vinylphosphonic acid (VPA) and 1-vinyl-1,2,4-triazole (VTri) were investigated. The copolymers were synthesized by free-radical copolymerization of the corresponding monomers at several monomer feed ratios to obtain poly(VPA-co-VTri) copolymer electrolytes. The final structures of the copolymers were confirmed by spectroscopic methods. The composition of the low molecular weight copolymers was varied with the feed ratio of the monomers. The presence of triazole units in the copolymers suppresses the formation of phosphonic acid anhydrides up to 150 degrees C, as verified by both (31)P NMR and TGA. The observation of defined glass transition temperatures indicated that the ionic interactions do not prevent segmental relaxations of the polymer chains. In the absence of humidity, the copolymer electrolyte, poly(VPA-co-VTri), S2 (with 33% triazole content) showed proton conductivity of 10(-3) S cm(-1) at 120 degrees C, which is far higher than in imidazole based copolymers. Two different types of hydrogen-bonded protons were detected by (1)H MAS NMR in the solid copolymer systems, due to different arrangements of triazole and phosphonic acid units.     

New polyelectrolytes based on 4‐vinyl‐1,2,3‐triazole and 1‐vinylimidazole

Copolymers of 4‐vinyl‐1,2,3‐triazole and 1‐vinylimidazole (VI) were obtained by radical copolymerization of (4‐vinyl‐1H‐1,2,3‐triazol‐1‐yl)methyl pivalate with VI followed by alkali hydrolysis. Reactivity ratios of the triazole and imidazole monomers are 0.51 and 0.30, respectively. Theoretical quantum‐chemical calculations by the PM3 semiempirical method give close values, which show that the obtained reactivity ratios reflect the activity of the vinyl groups. Polyelectrolyte properties of the copolymers were studied by potentiometric titration. Hydrogen bonds between the protonated triazole cycle and the triazole or imidazole units were found to considerably influence the solubility and solution properties of the copolymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Radical ring‐opening copolymerization behavior of vinyloxirane: Synthesis of copolymer from 2‐isopropenyl‐3‐phenyloxirane and styrene and its functionalization

The radical ring‐opening copolymerization of 2‐isopropenyl‐3‐phenyloxirane (1) with styrene (St) was examined to obtain the copolymer [copoly(1‐St)] with a vinyl ether moiety in the main chain. The copolymers were obtained in moderate yields by copolymerization in various feed ratios of 1 and St over 120 °C; the number‐average molecular weights (M_n) were estimated to be 1800–4200 by gel permeation chromatography analysis. The ratio of the vinyl ether and St units of copoly(1‐St) was estimated with the ¹H NMR spectra and varied from 1/7 to 1/14 according to the initial feed ratio of 1 and St. The haloalkoxylation of copoly(1‐St) with ethylene glycol in the presence of N‐chlorosuccinimide produced a new copolymer with alcohol groups and chlorine atoms in the side group in a high yield. The M_n value of the haloalkoxylated polymer was almost the same as that of the starting copoly(1‐St). The incorporated halogen was determined by elemental analysis. The analytical result indicated that over 88% of the vinyl ether groups participated in the haloalkoxylation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3729–3735, 2000     

Synthesis and reactivity ratios of regioisomeric vinyl‐1,2,3‐triazoles with styrene

The free radical reactivity ratios between styrene and different vinyl‐1,2,3‐triazole regioisomeric monomers in 1,4‐dioxane at 65 °C have been established using nonlinear least square method. The results obtained for the reactivity ratio between regioisomers show exceptionally different polymerization behavior, highlighting the effects of the electronic and steric factors of these regioisomeric monomers. The experimental results highlight the effects of the electronic and sterics on the copolymerization behavior. In case of 1,4‐vinyl‐triazoles, it was found that without the steric effects, the reactivity is very similar to that of styrene and forms random copolymers. However, it was found that 1,5‐vinyl‐triazoles are more reactive than 1,4‐vinyl triazoles. In the case of styrene‐co‐1,4‐vinyl‐1,2,3‐triazoles, the reactivity ratios were calculated to be r_styrene: r_{1‐octyl‐4‐vinyl‐triazole} = 1.97:0.54, r_styrene : r_{1‐benzyl‐4‐vinyl‐triazole} = 1.62:0.50, and r_styrene: r_{1‐methyl‐4‐vinyl‐triazole} = 0.90:0.87. On the other hand, reactivity ratios for styrene‐co‐1,5‐vinyl‐1,2,3‐triazoles were found to be r_styrene: r_{1‐octyl‐5‐vinyl‐triazole} = 0.13:0.66 and r_styrene: r_{1‐benzyl‐5‐vinyl‐triazole} = 0.34:0.49. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3359–3364     

Copolymerization of norbornene and 5‐norbornene‐2‐yl acetate using novel bis(β‐ketonaphthylamino)Ni(II)/B(C6F5)3/AlEt3 catalytic system

Vinyl‐type copolymerization of norbornene (NBE) and 5‐NBE‐2‐yl‐acetate (NBE‐OCOMe) in toluene were investigated using a novel homogeneous catalyst system based on bis(β‐ketonaphthylamino)Ni(II)/B(C₆F₅)₃/AlEt₃. The copolymerization behavior as well as the copolymerization conditions, such as the levels of B(C₆F₅)₃ and AlEt₃, temperature, and monomer feed ratios, which influence on the copolymerization were examined. Without combination of AlEt₃, the catalytic bis(β‐ketonaphthylamino)Ni(II)/B(C₆F₅)₃ exhibited very high catalyst activity for polymerization of NBE. Combination of AlEt₃ in catalyst system resulted in low conversion for polymerization of NBE. For copolymerization of NBE and NBE‐OCOMe, involvement of AlEt₃ in catalyst is necessary. Slight addition of NBE‐OCOMe in copolymerization of NBE and NBE‐OCOMe gives rise to significant increase of catalyst activity for catalytic system bis(β‐ketonaphthylamino)Ni(II)/B(C₆F₅)₃/AlEt₃. Nevertheless, excess increase of the NBE‐OCOMe content in the comonomer feed ratios results in decrease of conversion as well as activity of catalyst. The achieved copolymers were confirmed to be vinyl‐addition copolymers through the analysis of FTIR, ¹H NMR, and ¹³C NMR spectra. ¹³C NMR studies further revealed the composition of the copolymer and the incorporation rate was 7.6–54.1 mol % ester units at a content of 30–90 mol % of the NBE‐OCOMe in the monomer feeds ratios. TGA analysis results showed that the copolymer exhibited good thermal stability (T_d > 410 °C) and failed to observe the glass transitions temperature over 300 °C. The copolymers are confirmed to be noncrystalline by WAXD analysis results and show good solubility in common organic solvents. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3990–4000, 2009     

One‐ and two‐dimensional NMR characterization of N‐vinyl‐2‐pyrrolidone/methyl acrylate copolymers

N‐vinyl‐2‐pyrrolidone/methyl acrylate (V/M) copolymers were prepared by free‐radical bulk polymerization using benzoyl peroxide as an initiator. The copolymer composition of these copolymers was calculated from ¹H NMR spectra. The radical reactivity ratios for N‐vinyl‐2‐pyrrolidone (V) and methyl acrylate (M) were r_V = 0.09, r_M = 0.44. These reactivity ratios for the copolymerization of V and M were determined using the Kelen–Tudos and nonlinear least‐squares error‐in‐variable methods. The ¹³C{¹H} and ¹H NMR spectra of these copolymers overlapped and were complex. The complete spectral assignment of the ¹³C and ¹H NMR spectra were done with distortionless enhancement by polarization transfer and two dimensional ¹³C‐¹H heteronuclear single quantum correlation spectroscopic experiments. The two‐dimensional ¹H‐¹H homonuclear total correlation spectroscopic NMR spectrum showed the various bond interactions, thus inferring the possible structure of the copolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2225–2236, 2002     

One‐ and two‐dimensional NMR characterization of N‐vinyl‐2‐pyrrolidone/methyl acrylate copolymers

N‐vinyl‐2‐pyrrolidone/methyl acrylate (V/M) copolymers were prepared by free‐radical bulk polymerization using benzoyl peroxide as an initiator. The copolymer composition of these copolymers was calculated from ¹H NMR spectra. The radical reactivity ratios for N‐vinyl‐2‐pyrrolidone (V) and methyl acrylate (M) were r_V = 0.09, r_M = 0.44. These reactivity ratios for the copolymerization of V and M were determined using the Kelen–Tudos and nonlinear least‐squares error‐in‐variable methods. The ¹³C{¹H} and ¹H NMR spectra of these copolymers overlapped and were complex. The complete spectral assignment of the ¹³C and ¹H NMR spectra were done with distortionless enhancement by polarization transfer and two dimensional ¹³C‐¹H heteronuclear single quantum correlation spectroscopic experiments. The two‐dimensional ¹H‐¹H homonuclear total correlation spectroscopic NMR spectrum showed the various bond interactions, thus inferring the possible structure of the copolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2225–2236, 2002     

Anhydrous state proton conduction in sulfonated bisphenol a polyetherimide with 1H‐1,2,4 triazole as proton solvent

In this study, bisphenol A polyetherimide was sulfonated to various degrees (22, 48, and 62%) by trimethylsilylchlorosulfonate (TMSCS). Novel anhydrous proton conducting polyelectrolytes were prepared by the incorporation of 1H‐1,2,4‐triazole (Taz) as proton solvent in sulfonated polyetherimide (SPEI) matrix. The conductivity reached about 2 × 10^–3 S/cm at 80 °C and 10^–2 S/cm at 140 °C. The temperature dependence proton conductivity of the polyelectrolytes followed Arrhenius equation. The conductivity improved considerably at a temperature close to the triazole melting temperature in SPEI(X)H matrix. It was proposed that the high mobility of the triazolium ions (vehicle diffusion), in addition to structure diffusion, contribute to the high conductivity of these proton conducting electrolytes above the melting temperature of triazole. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2178–2187, 2009     

Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Synthesis and properties of water‐soluble azlactone copolymers

Preparation and study of a series of copolymers incorporating 2‐vinyl‐4,4‐dimethylazlactone (VDMA) is reported. The reactivity ratios for photo‐initiated free radical copolymerization of VDMA with methacrylic acid (MAA), acrylic acid (AA), acrylamide (AAm), dimethylacrylamide (DMAA), hydroxyethyl methacrylate (HEMA), methoxy poly(ethylene glycol) methacrylate (MPEG₃₀₀MA), and 2‐methacryloyloxyethyl phosphorylcholine (MPC), were determined by fitting comonomer conversion data obtained by in situ ¹H NMR to a terminal copolymerization equation. Semi‐batch photo‐copolymerizations were then used to synthesize the corresponding VDMA copolymers with constant composition. Their solubility and dissolution behavior, as well as their hydrolysis half‐lives under physiological conditions, were determined. P(VDMA‐co‐MAA) copolymers with 52 to 93 mol % VDMA showed decreasing initial solubility and increasing hydrolysis half‐lives with increasing VDMA content. VDMA copolymers with nonionic monomers AAm and DMAA were water soluble only at VDMA contents of 41 and 22 mol % or less, respectively, and showed longer hydrolysis half‐lives than comparable MAA copolymers. VDMA copolymers with HEMA and MPEG₃₀₀MA were found to crosslink during storage, so their hydrolysis half‐lives were not determined. VDMA copolymers with 18% zwitterionic MPC showed a much longer half‐life and superior initial solubility compared to analogous p(VDMA‐co‐MAA), identifying this copolymer as a promising candidate for macromolecular crosslinkers in, for example, aqueous layer‐by‐layer co‐depositions with polyamines. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of gradient copolymers based on 2‐phenyl‐2‐oxazoline and 2‐nonyl‐2‐oxazoline

In this study, the structure–property relationships for a series of statistical 2‐nonyl‐2‐oxazoline (NonOx) and 2‐phenyl‐2‐oxazoline (PhOx) copolymers were investigated for the first time. The copolymerization kinetics were studied and the reactivity ratios were calculated to be r_NonOx = 7.1 ± 1.4 and r_PhOx = 0.02 ± 0.1 revealing the formation of gradient copolymers. The synthesis of a systematical series of NonOx–PhOx copolymers is described, whereby the amount of NonOx was increased in steps of 10 mol %. The thermal and surface properties were investigated for this series of well‐defined copolymers. The thermal properties revealed a linear decrease in glass transition temperature for copolymers containing up to 39 wt % NonOx. Furthermore, the melting temperature of the copolymers containing 0 to 55 wt % PhOx linearly decreased most likely due to disturbance of the NonOx crystalline domains by incorporation of PhOx in the NonOx part of the copolymer. The surface energies of spincoated polymer films revealed a strong decrease in surface energy upon incorporation of NonOx in the copolymers due to strong phase separation between NonOx and PhOx allowing the NonOx chains to orient to the surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6433–6440, 2009     

Effects of different acid functional groups on proton conductivity of polymer‐1,2,4‐triazole blends

Proton transfer reactions under anhydrous conditions have attracted remarkable interest due to chemical energy conversions in polymer electrolyte membrane fuel cells. In this work, 1H‐1,2,4‐triazole (Tri) was used as a proton solvent in different polymer host matrices such as Poly(vinylphosphonic acid) (PVPA), and poly(2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) (PAMPS). PVPATri_x and PAMPSTri_x electrolytes were investigated where x is the molar ratio of Tri to corresponding polymer repeat unit. The interaction between polymer and Tri was studied via FTIR spectroscopy. Thermogravimetry analysis and differential scanning calorimetry were employed to examine the thermal stability and homogeneity of the materials, respectively. PVPATri_1.5 showed a maximum water‐free proton conductivity of 2.3 × 10^?3 S/cm at 120 °C and that of PAMPSTri₂ was 9.3 × 10^?4 S/cm at 140 °C. The results were interpreted in terms of different acidic functional groups and composition. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3315–3322, 2006     

Conducting films of poly(aniline‐co‐1‐amino‐ 2‐naphthol‐4‐sulfonic acid) blended with LDPE for its application as antistatic encapsulation material

The paper presents the electrostatic charge dissipative (ESD) properties of the conducting copolymers of aniline (AN) and 1‐amino‐2‐naphthol‐4‐sulfonic acid (ANSA) blended with low‐density polyethylene (LDPE). The copolymers of aniline and ANSA were synthesized under different reaction conditions. Blending of copolymers with LDPE was carried out in twin screw extruder by melt blending method by loading 0.5 and 1.0 wt% of the conducting copolymer in LDPE matrix. The mechanical properties of the blended films depend on the incorporation of copolymer in the LDPE matrix. The morphology of copolymer–LDPE blend was studied by scanning electron microscopy. The conductivity of the blown film of poly(AN‐co‐ANSA)/LDPE blend was found to be in the range of 10^?6–10^?11 S/cm, showing its potential use as antistatic bag for the encapsulation of electronic equipments. The static decay time of the film was found to be of the order of 0.1–1.9 sec on recording the decay time from 5000 to 500 V. Static charge measurements carried out on the films show that no charge is present on the surface. The level of interaction between the copolymers and the matrix polymer was determined by the FTIR spectra, blend morphology, electrical conductivity, and thermal analysis. The effect of the morphology on electrical and antistatic behavior of copolymers has also been investigated. Copyright © 2009 John Wiley & Sons, Ltd.     

Nitroxide‐mediated radical copolymerization of methyl methacrylate controlled with a minimal amount of 9‐(4‐vinylbenzyl)‐9H‐carbazole

The controlled nitroxide‐mediated homopolymerization of 9‐(4‐vinylbenzyl)‐9H‐carbazole (VBK) and the copolymerization of methyl methacrylate (MMA) with varying amounts of VBK were accomplished by using 10 mol % {tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino} nitroxide relative to 2‐({tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino}oxy)‐2‐methylpropionic acid (BlocBuilder?) in dimethylformamide at temperatures from 80 to 125 °C. As little as 1 mol % of VBK in the feed was required to obtain a controlled copolymerization of an MMA/VBK mixture, resulting in a linear increase in molecular weight versus conversion with a narrow molecular weight distribution (M_w /M_n ≈ 1.3). Preferential incorporation of VBK into the copolymer was indicated by the MMA/VBK reactivity ratios determined: r_VBK = 2.7 ± 1.5 and r_MMA = 0.24 ± 0.14. The copolymers were found significantly “living” by performing subsequent chain extensions with a fresh batch of VBK and by ³¹P NMR spectroscopy analysis. VBK was found to be an effective controlling comonomer for NMP of MMA, and such low levels of VBK comonomer ensured transparency in the final copolymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of poly (1‐vinyl‐3‐butylimidazolium‐co‐methyl methacrylate) gel polymer electrolytes for dye‐sensitized solar cells: Effect of structure and composition

Herein, three ionic liquid random copolymers (P) containing 1‐vinyl‐3‐butylimidazolium bromide (VBImBr) and methyl methacrylate (MMA) with various molar ratios were prepared using conventional free radical polymerization. Afterward, their corresponding chemically cross‐linked copolymers (XP) were formed similarly in the presence of polyethylene glycol dimethacrylate (PEGDMA). The synthesized copolymers were characterized using FT‐IR, ¹H NMR, and GPC. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) results showed that the rigidity and thermal stability of the copolymers depended on the ionic liquid content as well as the degree of cross‐linking. Gel polymer electrolytes were then prepared via obtained copolymers in the presence of a constant amount of synthesized imidazolium‐based ionic liquid. Among the copolymers, the P3 with in feed VBImBr:MMA molar ratio of 70:30 and the cross‐linked 1%‐XP3 copolymer prepared with 1 mol% of PEGDMA exhibited the highest conductivity and diffusion coefficients for I₃^¯ and I^¯. The power conversion efficiency of the optimized linear and cross‐linked copolymers (P3 and 1%‐XP3) under the simulated AM 1.5 solar spectrum irradiation at 100 mW cm^?2 were 3.49 and 4.13% in the fabricated dye‐sensitized solar cells (DSSCs), respectively. The superior long‐term stability and high performance of the gel electrolyte containing 1%‐XP3 suggested it as commercial gel electrolyte for future DSSCs.     

Radical copolymerization of vinylidene fluoride with 1‐bromo‐2,2‐difluoroethylene

The radical copolymerization of vinylidene fluoride (VDF) and 1‐bromo‐2,2‐difluoroethylene (BDFE) in 1,1,1,3,3‐pentafluorobutane solution at different monomer molar ratios (ranging from 96/4 to 25/75 mol %) and initiated by tert‐butylperoxypivalate (TBPPI, mainly) is presented. Poly(VDF‐co‐BDFE) copolymers of various aspects (from white powders to yellow viscous liquids) were produced depending on the copolymer compositions. The microstructures of the obtained copolymers were characterized by ¹⁹F and ¹H NMR spectroscopy and by elementary analysis and these techniques enabled one to assess the contents of both comonomers in the produced copolymers. VDF was shown to be more incorporated in the copolymer than BDFE. From the extended Kelen and Tudos method, the kinetics of the radical copolymerization led to the determination of the reactivity ratios, r_i, of both comonomers (r_VDF = 1.20 ± 0.50 and r_{BDFE =} 0.40 ± 0.15 at 75 °C) showing that VDF is more reactive than BDFE. Alfrey‐Price's Q and e values of BDFE monomer were calculated to be 0.009 (from Q_VDF = 0.008) or 0.019 (from Q_VDF = 0.015) and +1.22 (vs. e_VDF = 0.40) or +1.37 (vs. e_VDF = 0.50), respectively, indicating that BDFE is an electron‐accepting monomer. Statistic cooligomers were produced with molar masses ranging from 1,800 to 5,500 g/mol (assessed by GPC with polystyrene standards). A further evidence of the successful copolymerization was shown by the selective reduction of bromine atoms in poly(VDF‐co‐BDFE) cooligomers that led to analog PVDF. The thermal properties of the poly(VDF‐co‐BDFE) cooligomers were also determined and those containing a high VDF amount exhibited a high thermal stability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3964–3976, 2010.     

Synthesis and enzymatic degradation of 2‐methylene‐1,3‐dioxepane and methyl acrylate copolymers

Copolymers of 2‐methylene‐1,3‐dioxepane (MDO) and methyl acrylate (MA) containing ester units both in the backbone and as pendant groups were synthesized by free‐radical copolymerization. The influence of reaction conditions such as the polymerization time, temperature, initiator concentration, and comonomer feed ratio on the yield, molecular weight, and copolymer composition was investigated. The structure of the copolymers was confirmed by ¹H NMR, ¹³C NMR, and IR spectroscopy. Differential scanning calorimetry indicated that the copolymers had a random structure. An NMR study showed that hydrogen transfer occurred during the copolymerization. The reactivity ratios of the comonomers were r_MDO = 0.0235 and r_MA = 26.535. The enzymatic degradation of the copolymers obtained was carried out in the presence of proteinase K or a crude enzyme extracted from earthworms. The experimental results showed that the higher ester molar percentage in the backbone caused a faster degradation rate. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2898–2904, 2003     

Radical copolymerization of chlorotrifluoroethylene with 4‐bromo‐3,3,4,4‐tetrafluorobut‐1‐ene

The radical copolymerization of chlorotrifluoroethylene (CTFE) with 3,3,4,4‐tetrafluoro‐4‐bromobut‐1‐ene (BTFB) initiated by tert‐butylperoxypivalate is presented. The microstructures of the obtained copolymers are determined by means of NMR spectroscopies and elemental analysis and show that random copolymers were obtained. A wide range of poly(CTFE‐co‐BTFB) copolymers is synthesized, containing from 17 to 89 mol % of CTFE. In all the cases, CTFE is the less reactive of both comonomers. T_d^10% values, ranging from 163 up to 359 °C, are dependent on the BTFB content. These variations of thermal property are attributed to the increase in the number of C‐H and C‐Br bonds breakdown when the BTFB molar percentage in the copolymer is higher. T_g values range from 19 to 39 °C and a decreasing trend is observed when increasing the amount of BTFB in the copolymer. This observation arises from the higher flexibility of the copolymer when increasing the number of fluorobrominated lateral chains. These original fluoropolymers bearing reactive pendant bromo groups are suitable candidates for various applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1714–1720