A novel non-enzyme hydrogen peroxide sensor based on an electrode modified with carbon nanotube-wired CuO nanoflowers

We have prepared a novel sensor for hydrogen peroxide that is based on a glassy carbon electrode modified with a film containing multi-walled carbon nanotubes wired to CuO nanoflowers. The nanoflowers were characterized by X-ray powder diffraction, and the electrode was characterized by cyclic voltammetry (CV) and scanning electron microscopy. The response of the modified electrode towards hydrogen peroxide was investigated by CV and chronoamperometry and showed it to exhibit high electrocatalytic activity, with a linear range from 0.5?μM to 82?μM and a detection limit of 0.16?μM. The sensor also displays excellent selectivity and stability.

Electrocatalysis of Puerarin on a Nano-CeO2/MWCNTs Composite Modified Electrode and Its Determination in Pharmaceutical Preparations

A good route for the fabrication of CeO₂ nanoparticles (nano‐CeO₂)/multi‐walled carbon nanotubes (MWCNTs) modified glassy carbon electrodes (GCE) was proposed. MWCNTs are used to immobilize nano‐CeO₂. What′s more, with the addition of the MWCNTs, the agglomeration level of CeO₂ nanoparticles can be reduced, the extremely large surface area can be obtained and the electron transfer rate can be increased. The morphological characterization of nano‐CeO₂/MWCNTs was examined by scanning electron microscopy (SEM). The performances of the nano‐CeO₂/MWCNTs/GCE were characterized with cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and typical amperometric response (i‐t). The potential utility of the constructed electrodes was demonstrated by applying them to the analytical determination of puerarin concentration. The catalytic oxidation of puerarin has a better result on nano‐CeO₂/MWCNTs/GCE because of the synergistic effect of nano‐CeO₂ and MWCNTs. An optimized limit of detection of 8.0×10^?9 mol/L was obtained at a signal‐to‐noise ratio of 3 and with a fast response time (within 3 s). Additionally, the nano‐CeO₂/MWCNTs/GCE exhibited a wide linear range from 0.04 to 6.0 μmol/L and high sensitivity.     

Sensitive Nucleic Acid Detection at NH2‐MWCNTs Modified Glassy Carbon Electrode and its Application for Monitoring of Gemcitabine‐DNA Interaction

An electrochemical dsDNA nanobiosensor was fabricated using amino‐functionalized multi walled carbon nanotubes modified glassy carbon electrode (NH₂fMWCNTs/GCE) for the sensitive detection of DNA bases and electrochemical monitoring of drug‐DNA interaction. The influence of functional groups on MWCNT was studied by MWCNT functionalized with NH₂ (NH₂fMWCNTs) and COOH (COOHfMWCNT) groups based on the signal of DNA bases. The modified electrodes were characterized by scanning electron microscopy. One layer of calf thymus double stranded deoxyribonucleic acid (ct‐dsDNA) was immobilized onto the NH₂fMWCNTs/GCE (dsDNA/NH₂fMWCNTs/GCE). The dsDNA/NH₂fMWCNTs/GCE were used to investigate the interaction between the dsDNA and the anticancer drug gemcitabine by differential pulse voltammetry in acetate buffer of pH 4.70. For the confirmation of interaction, the lowering in intensity of the current signals of guanine and adenine was considered as an indicator. Electrochemical impedance spectroscopy studies were performed for the comparison of the modified surfaces. In order to define and visualize the interaction mechanism between gemcitabine and dsDNA/NH₂fMWCNTs/GCE at the molecular level, in silico methods including docking and molecular dynamics simulations were employed.     

Electrocatalytic Activity of Nanohybrids Based on Carbon Nanomaterials and MFe2O4 (M=Co,Mn) towards the Reduction of Hydrogen Peroxide

We report the advantages of hybrid nanomaterials prepared with electrogenerated ferrites (MFe₂O₄; M: Co, Mn) and multi‐walled carbon nanotubes (MWCNTs) or thermally reduced graphene oxide (TRGO) on the electro‐reduction of hydrogen peroxide. Glassy carbon electrodes (GCE) modified with these hybrid nanomaterials dispersed in Nafion/isopropanol demonstrated a clear synergism on the catalytic reduction of reduction of hydrogen peroxide at pH 13.00. The intimate interaction between MFe₂O₄ and carbon nanomaterials allowed a better electronic transfer and a facilitated regeneration of M²⁺ at the carbon nanomaterials, reducing the charge transfer resistances for hydrogen peroxide reduction and increasing the sensitivities of the amperometric response.     

MWCNTs/Ionic Liquid/Graphene Quantum Dots Nanocomposite Coated with Nickel‐Cobalt Bimetallic Catalyst as a Highly Selective Non‐enzymatic Sensor for Determination of Glucose

In this work, a glassy carbon electrode (GCE) was modified with multiwall carbon nanotubes/ionic liquid/graphene quantum dots (MWCNTs/IL/GQDs) nanocomposite. Then, the nanocomposite was decorated with nickel‐cobalt nanoparticles (Ni?Co NPs), and it was used as a non‐enzymatic glucose sensor. Field emission scanning electron microscopy, X‐ray diffraction spectroscopy, and energy dispersive spectroscopy were employed to prove the electrodeposition of the Ni?Co NPs on the surface of MWCNTs/IL/GQDs/GCE. Also, cyclic voltammetric and amperometric methods were utilized for the investigation of the electrochemical behaviour of the Ni?Co NPs/MWCNTs/IL/GQDs/GCE for glucose oxidation. The novel amperometric sensor displayed two linear ranges from 1.0 to 190.0 μmol L^?1 and 190.0 to 4910 μmol L^?1 with a low detection limit of 0.3 μmol L^?1 as well as fast response time (2 s) and high stability. Also, the sensor showed good selectivity for glucose determination in the presence of ascorbic acid, citric acid, dopamine, uric acid, fructose, and sucrose, as potential interference species. Finally, the performance of the proposed sensor was investigated for the glucose determination in real samples. Ni?Co NPs/MWCNTs/IL/GQDs/GCE showed good sensitivity and excellent selectivity.     

Characterization and Electrocatalytic Activity of Nanocomposites Consisting of Nanosized Cobalt Tetraaminophenoxy Phthalocyanine,Multi‐walled Carbon Nanotubes and Gold Nanoparticles

Glassy carbon electrodes were modified with composites containing cobalt tetraaminophenoxy phthalocyanine nanoparticles (CoTAPhPc NP ), multi‐walled carbon nanotubes (MWCNT) and gold nanorods (AuNRs). The modified electrodes were studied for their electrocatalytic behavior towards the reduction of hydrogen peroxide. Phthalocyanine nanoparticles significantly improved electron transfer kinetics as compared to phthalocyanines which are not in the nanoparticle form when alone or in the presence of multiwalled carbon nanotubes (MWCNTs). CoTAPhPc NP ‐MWCNT‐GCE proved to be suitable for hydrogen peroxide detection with a catalytic rate constant of 3.45×10³ M^?1 s^?1 and a detection limit of 1.61×10^?7 M. Adsorption Gibbs free energy ΔG^o was found to be ?19.22 kJ mol^?1 for CoTAPhPc NP ‐MWCNT‐GCE.     

Highly Sensitive Hydrazine Sensor Based on Co(OH)2 Nanoflakes Electrochemically Deposited on MWCNTs

We delineate the electrochemical preparation of cobalt hydroxide nanoflakes Co(OH)₂ NFs on multi‐walled carbon nanotubes (MWCNTs) by potentiostatic methods. The preparation was done on the surface of glassy carbon electrode (GCE). The prepared nanocomposite was characterized by field emission scanning electron microscopy (FESEM), X‐ray diffraction spectroscopy (XRD) and X‐ray photo electron spectroscopy (XPS). The resulting f‐ MWCNTs/Co(OH)₂ NFs modified GCE exhibits a good electrocatalytic activity for the oxidation of hydrazine in terms of decreasing over potential and increasing peak current. The modified electrode holds good in the linear range from 0.5 to 15.5 μM with limit of detection as 87.5 nM. The sensitivity of our modified electrode is calculated to be 5733 μA/mM cm‐2. Remarkably, the obtained LOD value of our sensor is very lower compared to the recommended concentration of hydrazine in water by World health organization (WHO) and Environmental protective agency (EPA). The modified electrode detects hydrazine selectively even in the presence of common interferants. Various water samples were chosen to study the practical feasibility of our sensor. The sensor also exhibited an appreciable stability, repeatability and reproducibility.     

碳纳米管负载纳米金-石墨烯量子点修饰电极电化学检测过氧化氢

采用过氧化氢刻蚀法制备石墨烯量子点(GQDs),再采用原位化学还原法制备金纳米粒子-石墨烯量子点纳米复合物(Au NPs-GQDs),最后以聚二甲基二烯丙基氯化铵(PDDA)为交联剂将上述纳米复合物组装于多壁碳纳米管表面,制得金纳米粒子-石墨烯量子点-PDDA-多壁碳纳米管复合材料(Au NPs-GQDsPDDA-MWCNTs)。通过荧光光谱法、紫外-可见吸收光谱法和透射电子显微镜对上述复合材料进行表征。采用滴涂法制得该复合材料修饰的玻碳电极,研究了过氧化氢在该电极上的电化学行为。结果表明:在石墨烯量子点、金纳米粒子和多壁碳纳米管三者的协同作用下,该电极对过氧化氢的电氧化表现出强的催化活性。在优化条件下,安培法检测H_2O_2的线性范围为2.0×10~(-8)~1.5×10~(-3)mol/L,检出限(3sb)为8.0×10~(-9)mol/L,灵敏度为61.6μA/(mmol·L~(-1))。     

Platinum Nanoparticles Decorated Multiwalled Carbon Nanotubes – Ionic Liquid Composite Film Coated Glassy Carbon Electrodes for Sensitive Determination of Theophylline

Platinum nanoparticles (Pt_nano) decorated multiwalled carbon nanotubes (MWCNTs)–1‐octyl‐3‐methylimidazolium hexafluorophosphate ([omim][PF₆]) composite material (MWCNTs‐Pt_nano‐[omim][PF₆]) was fabricated and characterized for the first time. In the presence of [omim][PF₆], more Pt_nano could deposit on MWCNTs. The average diameter of the deposited Pt_nano was about 5 nm. The composite material film coated glassy carbon electrode (GCE) exhibited sensitive voltammetric response to theophylline (TP). Under the optimized conditions (i.e., preconcentration for 2 minutes on open circuit in 0.10 M pH 3.0 phosphate buffer), the anodic peak current of TP at about 1.1 V (vs. SCE) was linear to TP concentration over the range of 1.0×10^?8–1.0×10^?5 M. The detection limit was estimated to be 8.0×10^?9 M. The modified electrode was successfully applied to the determination of TP in medicine tablet and green tea. In addition, the voltammetric responses of hypoxanthine (HX), xanthine (Xan) and uric acid (UA) on the MWCNTs‐Pt_nano‐[omim][PF₆]/GCE were also discussed.     

Promotion Effect of Bismuth on Nickel Electrodeposition and Its Electrocatalysis to Glucose Oxidation

Metallic Bi and Ni were co‐deposited onto the surface of glass carbon electrode (GCE) from the electrolyte solution containing their respective nitrate to fabricate a Bi/Ni alloy modified GCE (Bi/Ni‐GCE). The purpose is to study the influence of Bi³⁺ on the deposition of Ni and that of deposited Bi on the electrocatalytic performance of Ni to glucose in alkali solution. The results show that both redox signal of Ni(OH)₂/NiOOH and Ni(OH)₂/NiOOH mediated electrocatalysis to glucose is remarkably increased in the presence of Bi. It seems that there is a synergistic effect between Bi and Ni on each other’s redox electrochemistry. It’s possible that the firstly deposited Bi on GCE surface helps to the following nucleation and growth of Ni, leading to the deposition of more metallic Ni on GCE surface. An extremely attractive feature of Bi/Ni‐GCE is reflected by the fast response time to the electrocatalytic oxidation of glucose. The electrode nearly responses immediately after glucose is added and it reaches a steady‐state level within only 2 seconds, demonstrating a good electrocatalytic property of Bi/Ni‐GCE. The calibration plot is linear over the wide concentration range of 0–5.8 mM with a sensitivity of 33.96 µA/mM and a correlation coefficient of 0.9985. The detection limit of the glucose was found to be 0.59 µM at a signal‐to‐noise ratio of 3. The fabricated Bi/Ni‐GCE was successfully employed to analyze the glucose level in blood samples, exhibiting high accuracy, strong resistance against inference and good reliability in the practical applications.     

Electrocatalytic Oxidation of Hydrogen Peroxide on Poly(m‐toluidine)‐Nickel Modified Carbon Paste Electrode in Alkaline Medium

The poly(m‐toluidine) film was prepared by using the repeated potential cycling technique in an acidic solution at the surface of carbon paste electrode. Then transition metal ions of Ni(II) were incorporated to the polymer by immersion of the modified electrode in a 0.2 M NiSO₄, also the electrochemical characterization of this modified electrode exhibits stable redox behavior of the Ni(III)/Ni(II) couple. The electrocatalytic ability of Ni(II)/poly(m‐toluidine)/modified carbon paste electrode (Ni/PMT/MCPE) was demonstrated by electrocatalytic oxidation of hydrogen peroxide with cyclic voltammetry and chronoamperometry methods in the alkaline solution. The effects of scan rate and hydrogen peroxide concentration on the anodic peak height of hydrogen peroxide oxidation were also investigated. The catalytic oxidation peak current showed two linear ranges with different slopes dependent on the hydrogen peroxide concentration and the lower detection limit was 6.5 μM (S/N=3). The catalytic reaction rate constant, (k_h), was calculated 5.5×10² M^?1 s^?1 by the data of chronoamperometry. This modified electrode has many advantages such as simple preparation procedure, good reproducibility and high catalytic activity toward the hydrogen peroxide oxidation. This method was also applied as a simple method for routine control and can be employed directly without any pretreatment or separation for analysis cosmetics products.     

Poly(pyridine‐3‐boronic acid)/Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrodes for Simultaneous Determination of Ascorbic Acid, 3,4‐Dihydroxyphenylacetic Acid and Uric Acid

Poly(pyridine‐3‐boronic acid) (PPBA)/multiwalled carbon nanotubes (MWCNTs) composite modified glassy carbon electrode (GCE) was used for the simultaneous determination of ascorbic acid (AA), 3,4‐dihydroxyphenylacetic acid (DOPAC) and uric acid (UA). The anodic peaks for AA, DOPAC and UA at the PPBA/MWCNTs/GCE were well resolved in phosphate buffer solution (pH 7.4). The electrooxidation of AA, DOPAC and UA in the mixture solution was investigated. The peak currents increase with their concentrations increasing. The detection limits (S/N=3) of AA, DOPAC and UA are 5 µM, 3 µM and 0.6 µM, respectively.     

Adsorptive Stripping Differential Pulse Voltammetric Determination of Risperidone with a Multi‐Walled Carbon Nanotube‐Ionic Liquid Paste Modified Glassy Carbon Electrode

A new composite electrode has been fabricated based on coating multi‐walled carbon nanotubes (MWCNTs) and n‐octylpyridinum hexafluorophosphate (OPPF₆) ionic liquid composite on a glassy carbon (GC) electrode (OPPF₆‐MWCNTs/GCE). This electrode shows very attractive electrochemical performances for electrooxidation of risperidone (RIS) compared to conventional electrodes using carbon and mineral oil, notably improved sensitivity and stability. The oxidation peak potentials in cyclic voltammogram of RIS on the OPPF₆‐MWCNTs/GCE was occurred around 230 mV vs. SCE at Britton–Robinson (B–R) buffer (pH 4.0) at scan rate of 100 mV s^?1. The electrochemical parameters such as diffusion coefficient (D), charge transfer coefficient (α) and the electron transfer rate constant (k/_s) were determined using cyclic voltammetry. Under the optimized conditions, the peak current was linear to risperidone concentration over the concentration range of 10–200 nM with sensitivity of 0.016 μA/nM^?1 using differential pulse voltammetry. The detection limit was 6.54 nM (S/N = 3). The electrode also displayed good selectivity and repeatability. In the presence of clozapine (CLZ) the response of RIS kept almost unchanged. Thus this electrode could find application in the determination of RIS in some real samples. The analytical performance of the OPPF₆‐MWCNTs/GCE was demonstrated for the determination of RIS in human serum and pharmaceutical samples.     

Electrochemical Determination and in silico Studies of Fludarabine on NH2 Functionalized Multiwalled Carbon Nanotube Modified Glassy Carbon Electrode

A sensitive voltammetric technique has been developed for the determination of Fludarabine using amine‐functionalized multi walled carbon nanotubes modified glassy carbon electrode (NH₂‐MWCNTs/GCE). Molecular dynamics simulations, an in silico technique, were employed to examine the properties including chemical differences of Fludarabine‐ functionalized MWCNT complexes. The redox behavior of Fludarabine was examined by cyclic, differential pulse and square wave voltammetry in a wide pH range. Cyclic voltammetric investigations emphasized that Fludarabine is irreversibly oxidized at the NH₂‐MWCNTs/GCE. The electrochemical behavior of Fludarabine was also studied by cyclic voltammetry to evaluate both the kinetic (k_s and E_a) and thermodynamic (ΔH, ΔG and ΔS) parameters on NH₂‐MWCNTs/GCE at several temperatures. The mixed diffusion‐adsorption controlled electrochemical oxidation of Fludarabine revealed by studies at different scan rates. The experimental parameters, such as pulse amplitude, frequency, deposition potential optimized for square‐wave voltammetry. Under optimum conditions in phosphate buffer (pH 2.0), a linear calibration curve was obtained in the range of 2×10^?7 M–4×10^?6 M solution using adsorptive stripping square wave voltammetry. The limit of detection and limit of quantification were calculated 2.9×10^?8 M and 9.68×10^?8 M, respectively. The developed method was applied to the simple and rapid determination of Fludarabine from pharmaceutical formulations.     

Avidin and Glucose Oxidase‐non‐covalently Functionalized Multi‐walled Carbon Nanotubes: A New Analytical Tool for Building a Bienzymatic Glucose Biosensor

We report an innovative supramolecular architecture for bienzymatic glucose biosensing based on the non‐covalently functionalization of multi‐walled carbon nanotubes (MWCNTs) with two proteins, glucose oxidase (GOx) (to recognize glucose) and avidin (to allow the specific anchoring of biotinylated horseradish peroxidase (b‐HRP)). The optimum functionalization was obtained by sonicating for 10 min 0.50 mg mL^?1 MWCNTs in a solution of 2.00 mg mL^?1 GOx+1.00 mg mL^?1avidin prepared in 50 : 50 v/v ethanol/water. The sensitivity to glucose for glassy carbon electrodes (GCE) modified with MWCNTs‐GOx‐avidin dispersion and b‐HRP (GCE/MWCNTs‐GOx‐avidin/b‐HRP), obtained from amperometric experiments performed at ?0.100 V in the presence of 5.0×10^?4 M hydroquinone, was (4.8±0.3) μA mM^?1 (r²=0.9986) and the detection limit was 1.2 μM. The reproducibility for 5 electrodes using the same MWCNTs/GOx‐avidin dispersion was 4.0 %, while the reproducibility for 3 different dispersions and 9 electrodes was 6.0 %. The GCE/MWCNT‐GOx‐avidin/b‐HRP was successfully used for the quantification of glucose in a pharmaceutical product and milk.     

A Comparison of a Nanostructured Enzymeless Au/Fe2O3/MWCNTs/GCE Electrode and a GOx Modified One in Electrocatalytic Detection of Glucose

Acid functionalized multi‐walled carbon nanotubes (f‐MWCNTs) were decorated with Au and Fe₂O₃ nanoparticles (FeONPs) and deposited on glassy carbon electrode (GCE). The resulting hybrid Au/Fe₂O₃/f‐MWCNTs/GCE electrode and the one further modified by glucose oxidase were compared for detection of glucose. FeONPs and Au were deposited on the f‐MWCNTs by sonication‐assisted precipitation and deposition‐precipitation methods, respectively. The morphology and structure of the samples were characterized by transmission electron microscopy, scanning electron microscopy, X‐ray diffraction and Raman spectroscopy. A uniform distribution of FeONPs with an average size of 5 nm increased the surface area of functionalized nanotubes from 39 to 50 m²/g. The electrocatalytic glucose detection on the modified electrodes was evaluated using cyclic voltammetry and chronoamperometry in 0.1 M phosphate buffer solution at pH 7.0. The non‐enzymatic and enzymatic electrodes show sensitivity of 512.4 and 921.4 mA/mM.cm² and detection limit of 1.7 and 0.9 mM, respectively. The enzymatic and enzymeless electrodes retained more than 70 % and 80 % of their cathodic faradic current after 70 days, respectively. The sensing mechanism of the non‐enzymatic biosensor is described through the reaction of glucose with iron (III) ions, while in the case of enzymatic electrode, glucose is oxidized by glucose oxidase.     

A Non‐Enzymatic Hydrogen Peroxide Sensor Based on Gold Nanoparticles/Carbon Nanotube/Self‐Doped Polyaniline Hollow Spheres

In this study, a novel non‐enzymatic hydrogen peroxide (H₂O₂) sensor was fabricated based on gold nanoparticles/carbon nanotube/self‐doped polyaniline (AuNPs/CNTs/SPAN) hollow spheres modified glassy carbon electrode (GCE). SPAN was in‐site polymerized on the surface of SiO₂ template, then AuNPs and CNTs were decorated by electrostatic absorption via poly(diallyldimethylammonium chloride). After the SiO₂ cores were removed, hollow AuNPs/CNTs/SPAN spheres were obtained and characterized by transmission electron microscopy (TEM), field‐emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR). The electrochemical catalytic performance of the hollow AuNPs/CNTs/SPAN/GCE for H₂O₂ detection was evaluated by cyclic voltammetry (CV) and chronoamperometry. Using chronoamperometric method at a constant potential of ?0.1 V (vs. SCE), the H₂O₂ sensor displays two linear ranges: one from 5 µM to 0.225 mM with a sensitivity of 499.82 µA mM^?1 cm^?2; another from 0.225 mM to 8.825 mM with a sensitivity of 152.29 µA mM^?1 cm^?2. The detection limit was estimated as 0.4 µM (signal‐to‐noise ratio of 3). The hollow AuNPs/CNTs/SPAN/GCE also demonstrated excellent stability and selectivity against interferences from other electroactive species. The sensor was further applied to determine H₂O₂ in disinfectant real samples.     

Nanostructured Alpha‐Nickel Hydroxide Electrodes for High Performance Hydrogen Peroxide Sensing

Nanostructured alpha‐nickel hydroxide (α‐Ni(OH)₂) immobilized on a Fluorine‐doped Tin Oxide (FTO) surface was explored for the construction of hydrogen peroxide amperometric Flow Injection Analysis (FIA) sensors. Their notable electrocatalytic activity and heterogeneous electron‐transfer rate were confirmed by the appearance of a broad and intense peak associated with the oxidation of hydrogen peroxide and the enhancement of sensibility in hydrodynamic conditions. The α‐Ni(OH)₂ electrodes exhibited a broad dynamic range (5×10^?6 to 1×10^?3 mol L^?1), low detection limit (2×10^?7 mol L^?1), good repeatability (RSD=1.29 % for 20 successive analyses), and a sensitivity greater than 500 µA mmol^?1 L^?1 cm^?2.     

A NADH Sensor Based on 1,2‐Naphththoquinone Electropolymerized on Multi‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

A new carbon nanotubes modified electrode (poly‐Nq‐MWCNTs/GCE) was fabricated by electropolymerization of 1,2‐naphththoquinone to the surface of multi‐walled carbon nanotubes modified electrode by casting method. The morphology of the nanocomposite was characterized by scanning electron microscopy. Cyclic voltammetry and chronoamperometry were applied to investigate the electrochemical properties of the poly‐Nq‐MWCNTs nanocomposite modified electrode. The result of electrochemical experiments showed that such modified electrode had a favorable catalytic ability to oxidation of β‐nicotinamide adenine dinucleotide (NADH). The resulted sensor was sensitiveness to NADH and achieved 95β of the steady‐state current within 5s. Furthermore, the anodic peak current was linear to the concentration of NADH for the range from 1.0 μM to 0.14 mM. The linear equation was: I(μA) = 0.3987 + 0.1035c (μmol/L), the correlation coefficient r = 0.9962, the detect limit is down to 1 × 10^?7 M (S/N = 3) and the sensitivity is 0.1035 μA/mmol. The well catalytic activity of the sensor was ascribed to the synergistic effect role played by MWCNTs and poly‐Nq. Moreover, the based sensor possesses good stability and reproducibility.     

Amperometric sensor for nitrite using a glassy carbon electrode modified with thionine functionalized MWCNTs/Au nanorods/SDS nanohybrids

A sensitive nitrite (NO₂^‐) biosensor was fabricated by using sodium dodecyl sulfate (SDS), Au nanorods, and thionine functionalized MWCNTs (TH‐f‐MWCNTs) nanohybrids modified glassy carbon electrode. TH was covalently immobilized on the MWCNTs via a carbodiimide reaction. Comparing with MWCNTs/GCE, TH‐f‐MWCNTs/GCE displays higher catalytic activity toward the oxidation of NO₂^‐, since TH not only promoted the electronic transmission but also could improve the concentration of NO₂^‐ at the surface of the modified electrode in acidic solutions. The Au nanorods (AuNRs) were prepared through a simple wet chemical method and were characterized by TEM. The extremely high surface‐to‐volume ratios associated with one dimension nanostructures make their electrical properties extremely sensitive to species adsorbed on surfaces and result in excellent sensitivity and selectivity. SDS displays excellent film forming ability, which made the electrode stable. Under optimal conditions, the linear range for the detection of nitrite was 0.26 to 51 μM, and the low detection limit was 20 nM. In addition, the modified electrode was successfully applied to determine nitrite in real water samples. Copyright © 2012 John Wiley & Sons, Ltd.