New bithiazole-based sensitizers for efficient and stable dye-sensitized solar cells

A series of new push-pull organic dyes (BT-I-VI), incorporating electron-withdrawing bithiazole with a thiophene, furan, benzene, or cyano moiety, as π?spacer have been synthesized, characterized, and used as the sensitizers for dye-sensitized solar cells (DSSCs). In comparison with the model compound T1, these dyes containing a thiophene moiety between triphenylamine and bithiazole display enhanced spectral responses in the red portion of the solar spectrum. Electrochemical measurement data indicate that the HOMO and LUMO energy levels can be tuned by introducing different π?spacers between the bithiazole moiety and cyanoacrylic acid acceptor. The incorporation of bithiazole substituted with two hexyl groups is highly beneficial to prevent close π-π aggregation, thus favorably suppressing charge recombination and intermolecular interaction. The overall conversion efficiencies of DSSCs based on bithiazole dyes are in the range of 3.58 to 7.51?%, in which BT-I-based DSSCs showed the best photovoltaic performance: a maximum monochromatic incident photon-to-current conversion efficiency (IPCE) of 81.1?%, a short-circuit photocurrent density (J(sc)) of 15.69?mA?cm(-2), an open-circuit photovoltage (V(oc)) of 778?mV, and a fill factor (ff) of 0.61, which correspond to an overall conversion efficiency of 7.51?% under standard global AM 1.5 solar light conditions. Most importantly, long-term stability of the BT-I-III-based DSSCs with ionic-liquid electrolytes under 1000?h of light soaking was demonstrated and BT-II with a furan moiety exhibited better photovoltaic performance of up to 5.75?% power conversion efficiency.     

Benzotriazole-Bridged Sensitizers Containing a Furan Moiety for Dye-Sensitized Solar Cells with High Open-Circuit Voltage Performance

Two new benzotriazole-bridged sensitizers are designed and synthesized ( BTA-I and BTA-II ) containing a furan moiety for dye-sensitized solar cells (DSSCs). Two corresponding dyes ( BTA-III and BTA-IV ) with a thiophene spacer were also synthesized for comparison. All of these dyes performed as sensitizers for DSSCs, and the photovoltaic performance data of these benzotriazole-bridged dyes showed a high open-circuit voltage (V_oc: 804–834 mV). Among the four dyes, DSSCs based on BTA-II , with a furan moiety and branched alkyl chain, showed the highest V_oc (834 mV), a photocurrent density (J_sc) of 12.64 mA cm⁻², and a fill factor (FF) of 0.64, corresponding to an overall conversion efficiency (η) of 6.72 %. Most importantly, long-term stability of the BTA-I , BTA-II , BTA-III , BTA-IV -based DSSCs with ionic-liquid electrolytes under 1000 h light-soaking was demonstrated, and BTA-II exhibited better photovoltaic performance of up to 5.06 % power conversion efficiency.     

Rapid Synthesis of Thiophene‐Based,Organic Dyes for Dye‐Sensitized Solar Cells (DSSCs) by a One‐Pot,Four‐Component Coupling Approach

This one‐pot, four‐component coupling approach (Suzuki–Miyaura coupling/C?H direct arylation/Knoevenagel condensation) was developed for the rapid synthesis of thiophene‐based organic dyes for dye‐sensitized solar cells (DSSCs). Seven thiophene‐based, organic dyes of various donor structures with/without the use of a 3,4‐ethylenedioxythiophene (EDOT) moiety were successfully synthesized in good yields based on a readily available thiophene boronic acid pinacol ester scaffold (one‐pot, 3‐step, 35–61 %). Evaluation of the photovoltaic properties of the solar cells that were prepared using the synthesized dyes revealed that the introduction of an EDOT structure beside a cyanoacrylic acid moiety improved the short‐circuit current (J_sc) while decreasing the fill factor (FF). The donor structure significantly influenced the open‐circuit voltage (V_oc), the FF, and the power conversion efficiency (PCE). The use of a n‐hexyloxyphenyl amine donor, and our originally developed, rigid, and nonplanar donor, both promoted good cell performance (η=5.2–5.6 %).     

Influence of Solvent and Bridge Structure in Alkylthio‐Substituted Triphenylamine Dyes on the Photovoltaic Properties of Dye‐Sensitized Solar Cells

Three new triphenylamine dyes that contain alkylthio‐substituted thiophenes with a low bandgap as a π‐conjugated bridge unit were designed and synthesized for organic dye‐sensitized solar cells (DSSCs). The effects of the structural differences in terms of the position, number, and shape of the alkylthio substituents in the thiophene bridge on the photophysical properties of the dye and the photovoltaic performance of the DSSC were investigated. The introduction of an alkylthio substituent at the 3‐position of thiophene led to a decrease in the degree of redshift and the value of the molar extinction coefficient of the charge‐transfer band, and the substituent with a bridged structure led to a larger redshift than that of the open‐chain structure. The introduction of bulky and hydrophobic side chains decreased the short‐circuit photocurrent (J_sc), which was caused by the reduced amount of dye adsorbed on TiO₂. This resulted in a decrease in the overall conversion efficiency (η), even though it could improve the open‐circuit voltage (V_oc) due to the retardation of charge recombination. Furthermore, the change in solvents for TiO₂ sensitization had a critical effect on the performance of the resulting DSSCs due to the different amounts of dye adsorbed. Based on the optimized dye bath and molecular structure, the ethylene dithio‐substituted dye ( ATT3 ) showed a prominent solar‐to‐electricity conversion efficiency of 5.20 %.     

Phenanthrene‐Fused‐Quinoxaline as a Key Building Block for Highly Efficient and Stable Sensitizers in Copper‐Electrolyte‐Based Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) based on Cu^II/I bipyridyl or phenanthroline complexes as redox shuttles have achieved very high open‐circuit voltages (V_OC, more than 1 V). However, their short‐circuit photocurrent density (J_SC) has remained modest. Increasing the J_SC is expected to extend the spectral response of sensitizers to the red or NIR region while maintaining efficient electron injection in the mesoscopic TiO₂ film and fast regeneration by the Cu^I complex. Herein, we report two new D‐A‐π‐A‐featured sensitizers termed HY63 and HY64 , which employ benzothiadiazole (BT) or phenanthrene‐fused‐quinoxaline (PFQ), respectively, as the auxiliary electron‐withdrawing acceptor moiety. Despite their very similar energy levels and absorption onsets, HY64 ‐based DSSCs outperform their HY63 counterparts, achieving a power conversion efficiency (PCE) of 12.5 %. PFQ is superior to BT in reducing charge recombination resulting in the near‐quantitative collection of photogenerated charge carriers.     

Organic Dyes with Well‐Defined Structures for Highly Efficient Dye‐Sensitised Solar Cells Based on a Cobalt Electrolyte

Seven SGT organics dyes, containing bis‐dimethylfluoreneyl amino groups with a dialkoxyphenyl unit as an electron donor and a cyanoacrylic acid group as an anchoring group, connected with oligothiophenes, fused thiophenes and benzothiadiazoles as π‐bridges, were designed and synthesised for applications in dye‐sensitised solar cells (DSSCs). The photovoltaic performance of DSSCs based on organic dyes with oligothiophenes depends on the molecular structure of the dyes, in terms of the length change of the π‐bridging units. The best performance was found with a π‐bridge length of about 6 Å. To further enhance the photovoltaic performance associated with this concept, cyclopenta[1,2‐b:5,4‐b′]dithiophene (CPDT) and benzothiadiazole were introduced into the π‐bridge unit. As a result, the DSSC based on the organic dye containing the CPDT moiety showed the best photovoltaic performance with a short‐circuit photocurrent density (J_sc) of 14.1 mA cm^?2, an open‐circuit voltage (V_oc) of 0.84 V and a fill factor (FF) of 0.72, corresponding to an overall conversion efficiency (η) of 8.61 % under standard AM 1.5 irradiation.     

Tuning the Spectroscopic,Electrochemical, and Photovoltaic Properties of Triaryl Amine Based Sensitizers through Ring‐Fused Thiophene Bridges

The ring‐fused thiophene derivatives benzo[c]thiophene and its precursor bicyclo[2.2.2]octadiene (BCOD) have been introduced as π‐conjugated spacers for organic push–pull sensitizers with dihexyloxy‐substituted triphenylamine as donor and cyanoacrylic acid as acceptor ( OL1 , OL2 , OL3 , OL4 , OL5 , OL6 ). The effects of the fused ring on the spectroscopic and electrochemical properties of these sensitizers and their photovoltaic performance in dye‐sensitized solar cells have been evaluated. Introduction of a binary benzo[c]thiophene and ethylenedioxy thiophene as π bridge caused a significant red shift of the characteristic intramolecular charge‐transfer band to 642 nm. It is found that the sensitizer OL3 , which contains one benzo[c]thiophene unit as π linker, gives the highest overall conversion efficiency of 5.03 % among all these dyes.     

Novel Thiazolo[5,4‐d]thiazole‐Based Organic Dyes for Quasi‐Solid‐State Dye‐Sensitized Solar Cells

A series of novel metal‐free organic dyes containing the thiazolo[5,4‐d]thiazole moiety were designed and synthesized for quasi‐solid‐state dye‐sensitized solar cells (DSSCs). Different alkoxy chains were introduced into the electron donor part of the dye molecules for comparison. The optical, electrochemical, and photovoltaic properties for all sensitizers were systematically investigated. It was found that the sensitizers with the different alkoxy groups have similar photophysical and electrochemical properties, such as absorbance and energy levels, owing to their close chemical structures. However, the quasi‐solid‐state DSSCs based on the resulting sensitizers exhibit different performance parameters. The quasi‐solid‐state DSSC based on sensitizer FNE74 with two octyloxy chains possessed the highest solar energy conversion efficiency of 5.10 % under standard AM 1.5G sunlight illumination without the use of coadsorbant agents.     

Benzotriazole‐Containing D–π–A Conjugated Organic Dyes for Dye‐Sensitized Solar Cells

A series of metal‐free benzotriazole‐based dipolar dyes have been developed as sensitizers for dye‐sensitized solar cells (DSSCs). Different heteroaromatic rings such as furan, thiophene, and selenophene, were used in combination with benzotriazole as the conjugated spacer group. Light harvesting, charge recombination, and electron injection of the cells fabricated are affected by the heteroaromatic ring used in the spacer. The DSSC with the thiophene‐containing dye has the highest conversion efficiency of 6.20 %, which reaches 85 % of the standard cell based on N719.     

High‐Performance Dye‐Sensitized Solar Cells Based on Phenothiazine Dyes Containing Double Anchors and Thiophene Spacers

A series of new push–pull phenothiazine‐based dyes ( HL1 , HL2 , HL3 , HL4 ) featuring various π spacers (thiophene, 3‐hexylthiophene, 4‐hexyl‐2,2′‐bithiophene) and double acceptors/anchors have been synthesized, characterized, and used as sensitizers for dye‐sensitized solar cells (DSSCs). Among them, the best conversion efficiency (7.31 %) reaches approximately 99 % of the N719‐based (7.38 %) DSSCs fabricated and measured under similar conditions. The dyes with two anchors have more efficient interfacial charge generation and transport compared with their congeners with only single anchor. Incorporation of hexyl chains into the π‐conjugated spacer of these double‐anchoring dyes can efficiently suppress dye aggregation and reduce charge recombination.     

High‐Performance Organic Materials for Dye‐Sensitized Solar Cells: Triarylene‐Linked Dyads with a 4‐tert‐Butylphenylamine Donor

A series of organic dyes were prepared that displayed remarkable solar‐to‐energy conversion efficiencies in dye‐sensitized solar cells (DSSCs). These dyes are composed of a 4‐tert‐butylphenylamine donor group (D), a cyanoacrylic‐acid acceptor group (A), and a phenylene‐thiophene‐phenylene (PSP) spacer group, forming a D‐π‐A system. A dye containing a bulky tert‐butylphenylene‐substituted carbazole (CB) donor group showed the highest performance, with an overall conversion efficiency of 6.70 %. The performance of the device was correlated to the structural features of the donor groups; that is, the presence of a tert‐butyl group can not only enhance the electron‐donating ability of the donor, but can also suppress intermolecular aggregation. A typical device made with the CB‐PSP dye afforded a maximum photon‐to‐current conversion efficiency (IPCE) of 80 % in the region 400–480 nm, a short‐circuit photocurrent density J_sc=14.63 mA cm^?2, an open‐circuit photovoltage V_oc=0.685 V, and a fill factor FF=0.67. When chenodeoxycholic acid (CDCA) was used as a co‐absorbent, the open‐circuit voltage of CB‐PSP was elevated significantly, yet the overall performance decreased by 16–18 %. This result indicated that the presence of 4‐tert‐butylphenyl substituents can effectively inhibit self‐aggregation, even without CDCA.     

Exploring the relevance of thiophene rings as bridge unit in acceptor‐bridge‐donor dyes on self‐aggregation and performance in DSSCs

The possibility of dye charge recombination in DSSCs remains a challenge for the field. This consists of: (a) back‐transfer from the TiO₂ to the oxidized dye and (b) intermolecular electron transfer between dyes. The latter is attributed to dye aggregation due to dimeric conformations. This leads to poor electron injection which decreases the photocurrent conversion efficiency. Most organic sensitizers are characterized by an Acceptor‐Bridge‐Donor ( A ‐Bridge‐ D ) arrangement that is commonly employed to provide charge separation and, therefore, lowering the unwanted back‐transfer. Here, we address the intermolecular electron transfer by studying the dimerization and photovoltaic performance of a group of A ‐Bridge‐ D structured dyes. Specifically, eight famous sulfur containing π‐bridges were analyzed ( A and D remained fixed). Through quantum mechanical and molecular dynamics approaches, it was found that the formation of weakly stabilized dimers is allowed. The dyes with covalently bonded and fused thiophene rings as Bridges, 6d and 7d as well as 8d with a fluorene, would present high aggregation and, therefore, high probability of recombination processes. Conversely, using TiO₂ cluster and surface models, delineated the shortest bridges to improve the adsorption energy and the stability of the system. Finally, the elongation of the bridge up to 2 and 3 units and their photovoltaic parameters were studied. These results showed that all the sensitizers are able to provide similar photocurrent outcomes, regardless of whether the bridge is elongated. © 2017 Wiley Periodicals, Inc.     

Unsymmetric Platinum(II) Bis(aryleneethynylene) Complexes as Photosensitizers for Dye‐Sensitized Solar Cells

Four new unsymmetric platinum(II) bis(aryleneethynylene) derivatives have been designed and synthesized, which showed good light‐harvesting capabilities for application as photosensitizers in dye‐sensitized solar cells (DSSCs). The absorption, electrochemical, time‐dependent density functional theory (TD‐DFT), impedance spectroscopic, and photovoltaic properties of these platinum(II)‐based sensitizers have been fully characterized. The optical and TD‐DFT studies show that the incorporation of a strongly electron‐donating group significantly enhances the absorption abilities of the complexes. The maximum absorption wavelength of these four organometallic dyes can be tuned by various structural modifications of the triphenylamine and/or thiophene electron donor, improving the light absorption range up to 650 nm. The photovoltaic performance of these dyes as photosensitizers in mesoporous TiO₂ solar cells was investigated, and a power conversion efficiency as high as 1.57 % was achieved, with an open‐circuit voltage of 0.59 V, short‐circuit current density of 3.63 mA cm^?2, and fill factor of 0.73 under simulated AM 1.5G solar illumination.     

Computational studies on optoelectronic and charge transfer properties of some perylene‐based donor‐π‐acceptor systems for dye sensitized solar cell applications

We report DFT studies on some perylene‐based dyes for their electron transfer properties in solar cell applications. The study involves modeling of different donor‐π‐acceptor type sensitizers, with perylene as the donor, furan/pyrrole/thiophene as the π‐bridge and cyanoacrylic group as the acceptor. The effect of different π‐bridges and various substituents on the perylene donor was evaluated in terms of opto‐electronic and photovoltaic parameters such as HOMO‐LUMO energy gap, λ_max, light harvesting efficiency(LHE), electron injection efficiency (Ø_inject), excited state dye potential (E^dye*), reorganization energy(λ), and free energy of dye regeneration (). The effect of various substituents on the dye–I₂ interaction and hence recombination process was also evaluated. We found that the furan‐based dimethylamine derivative exhibits a better balance of the various optical and photovoltaic properties. Finally, we evaluated the overall opto‐electronic and transport parameters of the TiO₂‐dye assembly after anchoring the dyes on the model TiO₂ cluster assembly.     

Thiophene π bridge effect on bulky side‐chained benzodithiophene‐based photovoltaic polymers

Recently, we have used terthiophene side chain to modify benzo[1,2‐b:4,5‐b′]dithiophene (BDT) to form novel building block for BDT polymers. In this paper, this building block is used to copolymerized with thieno[3,4‐c]pyrrole‐4,6‐dione (TPD) and thieno[3,4‐b]thiophene (TT). This building block and TPD‐ or TT‐based polymers (P1 and P3) show high open circuit voltage (V_OC) (ca. 0.9–0.95 V) and low energy loss (E_g–eV_OC) in solar cells devices compared with similar polymers without bulky side chain. We further introduce thiophene π bridge into these polymers backbone to form two other polymers (P2 and P4). We find this thiophene π bridge does contribute to this bulky side chained benzodithiophene polymer photovoltaic performances, especially for power conversion efficiencies (PCEs). The polymer solar cells (PSCs) performances are moderate in this article due to the serious aggregation in the PSCs active layer. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1615–1622     

Synthesis and photovoltaic properties of copolymers based on benzo[1,2‐b:4,5‐b′]dithiophene and thiophene with electron‐withdrawing side chains

Six alternating conjugated copolymers ( PL1 – PL6 ) of benzo[1,2‐b:4,5‐b′]dithiophene (BDT) and thiophene, containing electron‐withdrawing oxadiazole (OXD), ester, or alkyl as side chains, were synthesized by Stille coupling reaction. The structures of the polymers were confirmed, and their thermal, optical, electrochemical, and photovoltaic properties were investigated. The introduction of conjugated electron‐withdrawing OXD or formate ester side chain benefits to decrease the bandgaps of the polymers and improve the photovoltaic performance due to the low steric hindrance of BDT. Bulk heterojunction polymer solar cells (PSCs) were fabricated based on the blend of the as‐synthesized polymers and the fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) in a 1:2 weight ratio. The maximum power conversion efficiency of 2.06% was obtained for PL5 ‐based PSC under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Enhancements of Trifluoroacetic Acylated Five‐membered Heterocyclic Compounds Using as Additives in Dye Sensitized Solar Cells

In this study, five‐membered heterocyclic compounds are trifluoroacetic acylated for the purpose of providing more long pairs to enhance electrolyte in dye sensitized solar cells (DSSCs). Four five‐membered heterocyclic compounds will be trifluoroacetic acylated with trifluoroacetic anhydride by Friedel‐Crafts acylation: furan, thiophene, pyrrole and N‐methylpyrrole. The properties will be measured by cyclic voltage (CV), Fourier transform infrared spectroscopy (FTIR), solar simulator, and electrochemical impedance spectroscopy (EIS). We find out that furan and thiophene which we add in electrolyte as additives can increase short circuit current and photovoltaic efficiency, and furthermore, all the trifluoroacetic acylated heterocyclic compounds perform better photoelectric abilities than non‐trifluoroacetic acylated one. The photovoltaic efficiency will be increased from 4.439% to 5.197% when 1wt% trifluoroacetic acylated thiophene is added in electrolyte as additives.     

Dye‐Sensitized Solar Cells Based on (Donor‐π‐Acceptor)2 Dyes With Dithiafulvalene as the Donor

Dipolar metal‐free sensitizers (D‐π‐A; D=donor, π=conjugated bridge, A=acceptor) consisting of a dithiafulvalene (DTF) unit as the electron donor, a benzene, thiophene, or fluorene moiety as the conjugated spacer, and 2‐cyanoacrylic acid as the electron acceptor have been synthesized. Dimeric congeners of these dyes, (D‐π‐A)₂, were also synthesized through iodine‐induced dimerization of an appropriate DTF‐containing segment. Dye‐sensitized solar cells (DSSCs) with the new dyes as the sensitizers have cell efficiencies that range from 2.11 to 5.24 %. In addition to better light harvesting, more effective suppression of the dark current than the D‐π‐A dyes is possible with the (D‐π‐A)₂ dyes.     

Dye‐Sensitized Solar Cells Based on a Donor–Acceptor System with a Pyridine Cation as an Electron‐Withdrawing Anchoring Group

New hemicyanine dyes ( CM101 , CM102 , CM103 , and CM104 ) in which tetrahydroquinoline derivatives are used as electron donors and N‐(carboxymethyl)‐pyridinium is used as an electron acceptor and anchoring group were designed and synthesized for dye‐sensitized solar cells (DSSCs). Compared with corresponding dyes that have cyanoacetic acid as the acceptor, N‐(carboxymethyl)‐pyridinium has a stronger electron‐withdrawing ability, which causes the absorption maximum of dyes to be redshifted. The photovoltaic performance of the DSSCs based on dyes CM101 – CM104 markedly depends on the molecular structures of the dyes in terms of the n‐hexyl chains and methoxyl. The device sensitized by dye CM104 achieved the best conversion efficiency of 7.0 % (J_sc=13.4 mA cm^?2, V_oc=704 mV, FF=74.8 %) under AM 1.5 irradiation (100 mW cm^?2). In contrast, the device sensitized by reference dye CMR104 with the same donor but the cyanoacetic acid as the acceptor gave an efficiency of 3.4 % (J_sc=6.2 mA cm^?2, V_oc=730 mV, FF=74.8 %). Under the same conditions, the cell fabricated with N719 sensitized porous TiO₂ exhibited an efficiency of 7.9 % (J_sc=15.4 mA cm^?2, V_oc=723 mV, FF=72.3 %). The dyes CM101 – CM104 show a broader spectral response compared with the reference dyes CMR101 – CMR104 and have high IPCE exceeding 90 % from 450 to 580 nm. Considering the reflection of sunlight, the photoelectric conversion efficiency could be almost 100 % during this region.     

Effect of Substituents in Catechol Dye Sensitizers on Photovoltaic Performance of Type II Dye‐Sensitized Solar Cells

In order to provide a direction in molecular design of catechol (Cat) dyes for type II dye‐sensitized solar cells (DSSCs), the dye‐to‐TiO₂ charge‐transfer (DTCT) characteristics of Cat dyes with various substituents and their photovoltaic performance in DSSCs are investigated. The Cat dyes with electron‐donating or moderately electron‐withdrawing substituents exhibit a broad absorption band corresponding to DTCT upon binding to TiO₂ films, whereas those with strongly electron‐withdrawing substituents exhibit weak DTCT. This study indicates that the introduction of a moderately electron‐withdrawing substituent on the Cat moiety leads to not only an increase in the DTCT efficiency, but also the retardation of back electron transfer. This results in favorable conditions for the type II electron‐injection pathway from the ground state of the Cat dye to the conduction band of the TiO₂ electrode by the photoexcitation of DTCT bands.