Mechanisms for regularization of chain folds during annealing of polyhexamethylene adipamide

The regular fold content of polyhexamethylene adipamide depends on the initial crystallization conditions, the degree of orientation, and the annealing time and temperature. At low annealing temperatures, the regular fold content increases linearly with crystallinity and arises from lamellar crystallization of isolated amorphous or interlamellar regions. At intermediate annealing temperatures, the increase in regular fold content greatly exceeds the crystallinity increase. The excessive increase in folds in this temperature range arises from regularization of loose loops and melting and recrystallization from extended to more folded type of crystals. At the higher annealing temperature, the crystallinity shows an increase relative to the fold content, and this implies that the increase in fold period occurs at the expense of folding.     

生物质高压密相输送特性试验研究

生物质气流床气化技术是一项新技术,生物质加压密相输送是需要解决的关键问题之一。本文在大型中试高压密相试验装置上进行两种特殊生物质粉料的输送试验,研究物料特性和操作参数对其流动特性的影响。试验结果表明,本试验系统输送生物质稳定可靠,质量流量随着输送差压和发料罐压力的升高增大。随表观气速增大两种生物质弯管当量长度系数K近似为定值,生物质1的K值大于生物质2,且生物质1的K值随输送差压的增加而增大;两种生物质的固相摩擦系数随着体积分数和接收罐压力的增大逐渐增大。     

Characterization of poly (3-methyl thiophene) thin films prepared by modified chemical bath deposition

Poly (3-methyl thiophene) thin films were prepared by chemical bath deposition technique on glass substrate; the prepared thin films were characterized for structural, morphological and optical properties. The variation in the oxidant concentration has an influence on the properties of the P3MeT thin films. The increase in the oxidant concentration leads to increase in the thickness of the film. The binding energy increases due to increase in oxidation concentration. The P3MeT thin films show smooth surface morphology with increase in oxidant concentration whereas the contact angle of the thin film decreases with increase in oxidant concentration. The optical absorbance of these thin films was found to increase with decrease in the optical band gap due to increase in oxidant concentration.     

Thermosolutal convection of micropolar fluids in hydromagnetics

The thermosolutal convection in a layer of electrically conducting micropolar fluids heated and soluted from below in the presence of a uniform vertical magnetic field is considered. The presence of coupling between thermosolutal and micropolar effects may bring overstability in the system. The magnetic field also introduces oscillatory modes in the system and the Rayleigh number is found to increase with the increase in magnetic field. The possibility of oscillatory motions and the increase in Rayleigh number with increase in magnetic field is depicted graphically.     

W-Cu合金力学性能的第一性原理计算

采用基于密度泛函理论的第一性原理分析方法的CASTEP软件,计算了W-Cu_x(x=6.25,12.5,18.75,25,31.25,37.5,43.75,50)合金的晶格参数、体模量、剪切模量、杨氏模量等力学常数,还计算了焓变值、能带结构、电子态密度和电荷布局,研究Cu不同含量对W-Cu合金力学性能的影响.结果表明：Cu的添加会增加W基体触头材料的可塑性,韧性大小随着Cu含量的升高而增加,在掺杂比例为43.75%时达到最大值,韧性增加使得产生微裂纹的概率减小;另外还计算了W-Cu合金的态密度、能带结构和电荷布局,结果表明随着Cu含量的增加,共价性降低,金属性增强,便于加工成型.     

Effect of ausforming temperature and strain on the bainitic transformation kinetics of a low carbon boron steel

The effect of ausforming temperature and strain on the bainitic transformation kinetics was investigated in a low carbon boron steel. A new mechanism, which is based on the competition between the increase in nucleation rate and the decrease in average volume of bainite sheaf after deformation, is proposed. The increase in nucleation rate is due to the decrease in boron concentration at the grain boundaries after small deformation and the formation of sub-grain boundaries at the grain interior after large deformation. The decrease in average volume of bainite sheaf is ascribed to the frequent impingement of bainite sub-units after deformation. The increase in nucleation rate after deformation results in the decrease in incubation time, which is confirmed from the experiment. The increase in nucleation rate overcomes the decrease in average volume of bainite sheaf, resulting in the increase in transformation velocity and volume fraction after small deformation. On the contrary, the decrease in the average volume of bainite sheaf overcomes the increase in nucleation rate after large deformation, leading to the decrease in transformation velocity and volume fraction of bainite.     

一维光子晶体缺陷模偏振特性的研究

利用一维光子晶体的透射率公式,计算出一维光子晶体掺杂后TE波和TM波缺陷模的波长随入射角的响应曲线、缺陷模透射峰随入射角的响应曲线、缺陷模透射峰随入射波长的响应曲线.研究发现,TE波和TM波的缺陷模透射峰均随入射角的增加而向短波方向移动；TE波缺陷模透射峰的半高宽度(FWHM)和峰值随入射角的增加而减小,而TM波缺陷模透射峰的半高宽度(FWHM)和峰值确随入射角的增加而增加；对TM波其波长为λ0的缺陷模也存在明显的“广义布儒斯特角”现象, TE波的缺陷模不存在“广义布儒斯特角”现象.     

Influence of angles of incidence of laser radiation on the generation of fast ions

It was established experimentally that the number and energy of fast ions in laser plasma increased with increasing angle of focusing laser radiation onto a flat target. Numerical calculations showed that the increase in angle of focusing brought the mean angle of incidence of laser radiation closer to the optimal angle corresponding to the maximal efficiency of the resonance absorption mechanism and, as a result, increased the fraction of absorbed laser energy in the energy of fast electrons and increased the number of fast electrons. In turn, the increase in the energy and number of fast electrons resulted in an increase in the number of fast electrons involved in the formation of a self-consistent electric field at the target edge and led to the growth of the field strength, which, eventually, was the reason for the increase in the number and energy of fast ions.     

Dynamics of nanoparticle agglomeration in a magnetic fluid in a varying magnetic field

It is found that the dependence of the magnetic nanoparticle agglomerate length in a magnetic fluid on the applied magnetic field has three characteristic segments: a substantial increase in the agglomerate length with the magnetic field in the range of weak fields, a segment with an insignificant increase in the average length of agglomerates upon an increase in the field, and a sharp increase in the agglomerate length with a further increase in the field. It is shown that the agglomerate length increases in the range of strong magnetic fields due to a decrease in the spacing between adjacent agglomerates down to their complete coalescence. The total number of agglomerates decreases thereby.     

The Effect of Peroxide Cross-Linking on the Properties of Low-Density Polyethylene

Low-density polyethylene (LDPE) was chemically cross-linked with various amounts of dicumyl peroxide (DCP). The cross-link density, determined by Flory–Rehner theory, showed an increase with increasing DCP. The gel content, densities of cross-linked LDPE, thermal stability, crystallization, melting behavior, and tensile properties were studied. The results showed a new finding about the change of weight loss after cross-linking; with increase in temperature, the weight loss showed an increase below the temperature of about 450°C and then showed a decrease at temperatures from about 450°C to 500°C after being cross-linked. The crystallinity, melting point, crystallization temperature, and elongation at break decreased with the increase in DCP. However, the maximum tensile stress increased with the increase in DCP, and the cross-linked samples showed a rubber-like behavior with no flow.     

热处理温度对铜镍镀层的光谱性能的影响

采用电沉积法在镍表面制备铜镍镀层,并将该铜镍镀层在不同温度下进行热处理。分别用扫描电镜法(SEM)、能谱法(EDAX) 和X衍射法(XRD)等对热处理后的铜镍镀层进行表征,研究热处理温度对铜镍镀层的光谱性能的影响。用电镀的方法获得的铜镍镀层表面是由节瘤组成,热处理温度在25~600 ℃范围,随着热处理温度的升高,铜镍镀层表面的节瘤变小;热处理温度在600~900 ℃范围,随着热处理温度的升高,铜镍镀层表面的节瘤变小,铜镍镀层表面的节瘤间的分界线越不明显。热处理温度在25～900 ℃范围,随着热处理温度的升高,铜镍镀层中铜的含量减小,从82.52 at%减小到78.30 at%;镍的含量增加,从17.48 at%增加到21.70 at%。铜镍镀层为Cu_0.81Ni_0.19立方晶型结构,热处理温度在25～300 ℃范围,随着热处理温度的升高,Cu_0.81Ni_0.19的晶型结构更完整;热处理温度在600～900 ℃范围,铜镍镀层中可能有部分的Cu_0.81Ni_0.19立方晶型结构转变为Cu_3.8Ni立方晶型结构;随着热处理温度的升高,有利于Cu_3.8Ni(311)和Cu_0.81N_i0.19(311) 晶面的生长。     

DC electric-field-induced heterophase structure on the surface of a peierls metal

A theoretical study has been made of the formation of a heterostructure of alternating metallic and semiconducting phases in atomic chains of a Peierls-metal surface monatomic layer placed in an electrostatic field normal to the surface. It is shown that an increase in the electric field results in an increase in the critical temperature of the metal-semiconductor phase transition on the sample surface, an increase in the temperature interval within which the heterostructure exists, a decrease in its spatial period, and an increase in the depth of spatial modulation of the gap in the electronic spectrum.     

空气源热泵机组结霜问题的实验分析

基于空气源热泵在低温寒冷地区运行中遇到的结霜问题,对不同风速工况下,结霜过程中设备性能的变化进行分析,以换热量、换热系数为指标对不同翅型换热器的换热特性进行研究。实验结果显示:换热器结霜过程中,换热过程主要分为初始增加段、换热平稳段、缓慢衰减段、后期平稳等四段,结晶体在增加空气湍流度强化换热的同时,也增加了换热热阻使换热效果变差,因此换热效果本质而言是两种换热效果的综合体现;空气阻力随风速的增大、结霜量的增加而增大,而蒸发压力随着风速的增加而升高、随结霜量的增大而减小;百叶窗翅片表面结霜量大于平翅片,因此平翅片翅型当量换热系数更大,翅片结霜量、当量换热系数随风速的增加而增大,风速由1 m/s增至4 m/s时,结霜量、当量换热系数增加约三倍。     

Firing rates of coupled noisy excitable elements

The dynamics of coupled excitable FitzHugh Nagumo systems under external noisy driving is studied. Different from most of previous work focusing on the noise-induced regularity in the framework of coherence resonance, here the average frequency （or firing rate） of coupled excitable elements is of much more concern. We find that （i） their frequencies first increase and then decrease with the increase of the coupling, and there is a clear crossover from a rush increase to a smooth increase with the increase of noise strength, and （ii） for nonidentical cases, all elements transit to an identical frequency simultaneously only after a certain coupling strength is achieved. These first-increase-thendecrease non-monotonic frequency behavior and isochronous frequency synchronization are believed to be two basic behaviors in coupled noisy excitable systems.     

Experimental investigation of the conduction mechanism of hydrogenated PEG thin films at high relative humidities

The electrical properties of pure, hydrogenated and hydrophobically modified polyethylene glycole (PEG) thin films under changing relative humidity conditions are investigated by dc measurements. Perfluoroalkylethylalcohol is used as the hydrophobic additive. The conductivity of all samples increases gradually up to around 70% relative humidity, beyond which there exists a steep increase. For the pure PEG samples, after 75%, the conductivity shows irregularities with respect to the increase in the relative humidity. The irregularities subside in the hydrogenated as well as the hydrophobically modified PEG samples, while in the latter the steep increase in conductivity shifts to higher values of relative humidity with the increase of perfluoroalkylethylalcohol concentration in the film.     

量子点中极化子的内部激发态性质

采用Huybrechts线性组合算符和幺正变换方法研究了抛物量子点中的强、弱耦合极化子的激发态性质。分别导出强、弱耦合情况下,抛物量子点中的极化子的第一内部激发态能量、激发能量、共振频率与量子点的有效受限长度和电子-声子耦合强度的关系。数值计算结果表明,量子点中弱耦合和强耦合极化子的内部激发态能量、激发能量和共振频率都随量子点的有效受限长度的减小而迅速增大。弱耦合极化子的第一内部激发态能量随电子-声子耦合强度的增加而减少;而强耦合极化子的振动频率随量子点的有效受限长度的减小而迅速增加。弱耦合极化子的第一内部激发态能量、激发能量和共振频率随电子-声子耦合强度的增加而减小。     

外电场下BN分子的结构及性质

采用QCISD方法研究了BN基态分子在不同场强条件下的稳定构型及激发态性质。分析了外电场对BN分子键长、总能量、能级、谐振频率和红外谱强度以及对BN分子前10个激发态的激发能、振子强度等的影响。结果表明随着正向电场的逐渐增大, BN分子键长先减小后增大;分子总能量则先增大后减小;分子电偶极矩 增大;费米能级和能隙均减小。谐振频率及红外谱强度均随正向电场的增大而增大。由基态到第1激发态的波长减小,激发能增大,而基态至第2-10激发态的波长增大而激发能减小。     

外电场下BN分子的结构及性质

采用QCISD方法研究了BN基态分子在不同场强条件下的稳定构型及激发态性质。分析了外电场对BN分子键长、总能量、能级、谐振频率和红外谱强度以及对BN分子前10个激发态的激发能、振子强度等的影响。结果表明随着正向电场的逐渐增大, BN分子键长先减小后增大;分子总能量则先增大后减小;分子电偶极矩μ增大;费米能级和能隙均减小。谐振频率及红外谱强度均随正向电场的增大而增大。由基态到第1激发态的波长减小,激发能增大,而基态至第2－10激发态的波长增大而激发能减小。     

Absence of an abrupt phase change from polycrystalline to amorphous in silicon with deposition temperature.

Using fluctuation electron microscopy, we have observed an increase in the mesoscopic spatial fluctuations in the diffracted intensity from vapor-deposited silicon thin films as a function of substrate temperature from the amorphous to polycrystalline regimes. We interpret this increase as an increase in paracrystalline medium-range order in the sample. A paracrystal consists of topologically crystalline grains in a disordered matrix; in this model the increase in ordering is caused by an increase in the grain size or density. Our observations are counter to the previous belief that the amorphous to polycrystalline transition is a discontinuous disorder-order phase transition.     

球形雾霾粒子的紫外光散射偏振特性研究

在我国经济社会快速发展的同时,雾霾天气成为了突出的环境问题,雾霾粒子的测量非常重要。偏振紫外光与大气雾霾粒子发生散射后,散射光偏振状态(Stokes矢量以及偏振度)的改变能反映雾霾粒子的相关物理特性(粒径、复杂折射率等)。基于Mie散射理论建立了紫外光雾霾球形粒子直视和非直视单次散射模型,研究了单个球形粒子和链状结构球形粒子物理特性的改变对散射光偏振状态的影响,并用蒙特卡洛仿真分析已知粒径分布的雾霾粒子浓度对散射光偏振状态的影响。结果表明：针对单个球形粒子,随着粒子粒径的增大Stokes矢量中散射光光强(I_s)随之增强,粒子复折射率虚部为先增大后较小,偏振度也是在不断增大,且复折射率虚部较小时,偏振度增加趋势快;对于粒径分布不变的雾霾粒子,随着粒子的浓度增加,雾霾粒子的散射系数、消光系数和吸收系数均呈线性增加,但是I_s先增大后减小。针对链状球形粒子,随着粒子个数的增加,I_s均呈现增大的趋势,且偏振度可用于区分链状球形粒子是否由相同球形粒子组成; 相同球形粒子组成链状结构中,I_s随着粒子数量的增加而线性增大,偏振度不改变;不同球形粒子组成的链状结构,I_s以及偏振度的变化趋势可以区分粒子物理特性。