Effect of ZnS layers on optical properties of prepared CdS/TiO<Subscript>2</Subscript> nanotube arrays for photocatalyst

The TiO₂ nanotube arrays (TiO₂ NTAs) prepared by re-oxidation were chosen as basement. The NTAs prepared through re-oxidation show smoother surface and more uniform tube mouth on large scale compared with the first as-grown one. We use successive ionic layer adsorption and reaction method to deposit quantum dots (ZnS and CdS) onto the sample successively. The findings reveal that two kinds of quantum dots (～10 nm) distribute regularly and the nanotube mouth is open. From the UV–Vis absorption spectrum of samples, the red shift occurs after the sedimentation of the two quantum dots, which proves that the double modification can expand the absorption to 650 nm. Among all specimens, the sample produced by co-deposition has the highest speed of catalytic efficiency of 90.7% compared with bare TiO₂ NTAs (52.9%) and just CdS QDs sensitized sample (65.8%). In the test of photocatalysis durability, the decay percentages of CdS/TiO₂ NTAs and ZnS/CdS/TiO₂ NTAs were 35.8 and 48.4%, respectively, which means that the ZnS passivation layer plays a crucial role in enhancing photocatalytic activities.     

Two-step annealed CdS/CdSe co-sensitizers for quantum dot-sensitized solar cells

CdS/CdSe co-sensitizers on TiO₂ films were annealed using a two-step procedure; high temperature (300 °C) annealing of TiO₂/CdS quantum dots (QDs), followed by low temperature (150 °C) annealing after the deposition of CdSe QDs on the TiO₂/CdS. For comparison, two types of films were prepared; CdS/CdSe-assembled TiO₂ films conventionally annealed at a single temperature (150 or 300 °C) and non-annealed films. The 300 °C-annealed TiO₂/CdS/CdSe showed severe coalescence of CdSe QDs, leading to the blocked pores and hindered ion transport. The QD-sensitized solar cell (QD-SSC) with the 150 °C-annealed TiO₂/CdS/CdSe exhibited better overall energy conversion efficiency than that with the non-annealed TiO₂/CdS/CdSe because the CdSe QDs annealed at a suitable temperature (150 °C) provided better light absorption over long wavelengths without the hindered ion transport. The QD-SSC using the two-step annealed TiO₂/CdS/CdSe increased the cell efficiency further, compared to the QD-SSC with the 150 °C-annealed TiO₂/CdS/CdSe. This is because the 300 °C-annealed, highly crystalline CdS in the two-step annealed TiO₂/CdS/CdSe improved electron transport through CdS, leading to a significantly hindered recombination rate.     

Influence of TiO2 nanotube morphology and TiCl4 treatment on the charge transfer in dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) were fabricated using TiO₂ nanoparticles (NPs), TiO₂ nanotube arrays (NTAs), and surface-modified NTAs with a TiCl₄ treatment. The photovoltaic efficiencies of the DSSCs using TiO₂ NP, NTA, and TiCl₄-treated NTA electrodes are 4.25, 4.74, and 7.47 %, respectively. The highest performance was observed with a TiCl₄-treated TiO₂ NTA photoanode, although in the case of the latter two electrodes, the amounts of N719 dye adsorbed were similar and 68 % of that of the NP electrode. Electrochemical impedance measurements show that the overall resistance, including the charge–transfer resistance, was smaller with NTA morphologies than with NP morphologies. We suggest that a different electron transfer mechanism along the one-dimensional nanostructure of the TiO₂ NTAs contributes to the smaller charge–transfer resistance, resulting in a higher short circuit current (J _sc), even at lower dye adsorption. Furthermore, the TiCl₄-treated NTAs showed even smaller charge–transfer resistance, resulting in the highest J _sc value, because the downward shift in the conduction band edge improves the electron injection efficiency from the excited dye into the TiCl₄-treated TiO₂ electrodes.     

Anatase TiO<Subscript>2</Subscript> nanoparticles for lithium-ion batteries

Anatase TiO₂ nanoparticles were prepared by a simple sol-gel method at moderate temperature. X-ray powder diffraction (XRD) and Raman spectroscopy revealed the exclusive presence of anatase TiO₂ without impurities such as rutile or brookite TiO₂. Thermogravimetric analysis confirmed the formation of TiO₂ at about 400 °C. Particle size of about 20 nm observed by transmission electron microscopy matches well with the dimension of crystallites calculated from XRD. The electrochemical tests of the sol-gel-prepared anatase TiO₂ show promising results as electrode for lithium-ion batteries with a stable specific capacity of 174 mAh g^?1 after 30 cycles at C/10 rate. The results show that improvement of the electrochemical properties of TiO₂ to reach the performance required for use as an electrode for lithium-ion batteries requires not only nanosized porous particles but also a morphology that prevents the self-aggregation of the particles during cycling.     

Preparation and electrochemical performances of nanoporous/cracked cobalt oxide layer for supercapacitors

Nanoporous/cracked structures of cobalt oxide (Co₃O₄) electrodes were successfully fabricated by electroplating of zinc–cobalt onto previously formed TiO₂ nanotubes by anodizing of titanium, leaching of zinc in a concentrated alkaline solution and followed by drying and annealing at 400 °C. The structure and morphology of the obtained Co₃O₄ electrodes were characterized by X-ray diffraction, EDX analysis and scanning electron microscopy. The results showed that the obtained Co₃O₄ electrodes were composed of the nanoporous/cracked structures with an average pore size of about 100 nm. The electrochemical capacitive behaviors of the nanoporous Co₃O₄ electrodes were investigated by cyclic voltammetry, galvanostatic charge–discharge studies and electrochemical impedance spectroscopy in 1 M NaOH solution. The electrochemical data demonstrated that the electrodes display good capacitive behavior with a specific capacitance of 430 F g^?1 at a current density of 1.0 A g^?1 and specific capacitance retention of ca. 80 % after 10 days of being used in electrochemical experiments, indicating to be promising electroactive materials for supercapacitors. Furthermore, in comparison with electrodes prepared by simple cathodic deposition of cobalt onto TiO₂ nanotubes(without dealloying procedure), the impedance studies showed improved performances likely due to nanoporous/cracked structures of electrodes fabricated by dealloying of zinc, which provide fast ion and electron transfer routes and large reaction surface area with the ensued fast reaction kinetics.     

Crystalline orientation preference for TiO2 nanotube arrays with efficient photoelectrochemical properties

Novel TiO₂ nanotube arrays (TiO₂ NTAs) with preferred oriented crystalline structure were firstly achieved by a facile method through anodizing Ti sheets with textured microstructure. Highly oriented crystalline structure of TiO₂ NTAs, with its (004) lattice plane of anatase TiO₂ paralleling to the top surface of TiO₂ NTAs was identified by the results of XRD, which was further confirmed by the regular diffraction spots and lattice fringes with uniform direction in HRTEM images. In comparison with normal randomly oriented TiO₂ NTAs, the quasi-single crystal structure of highly oriented TiO₂ NTAs can suppress the recombination of photogenerated electron–hole pairs and enhance the transfer of photocarriers, as was proved by the photoelectrochemical measurement conducted on both normal TiO₂ and oriented TiO₂ NTAs. The results of this study provide a promising avenue to obtain high photoelectrochemical performance TiO₂ NTAs-based hybrid nanomaterials.     

Coarsening-resistant Ag nanoparticles stabilized on amorphous TiO<Subscript>x</Subscript> nanoparticles

Bare Ag nanoparticles (～10 nm) and Ag nanoparticles (1–20 nm) on the surfaces of larger TiO_x nanoparticles were prepared by laser ablation of microparticle aerosols (LAMA). The behaviors of the nanoparticles during high temperature annealing were then studied with ex situ and in situ transmission electron microscopy. For the ex situ heating experiments, Ag and Ag-on-TiO_x NPs were collected onto gold TEM grids and subjected to annealing treatments at 500 °C in argon, vacuum, and air. At this temperature, bare Ag NPs on carbon TEM supports coarsened rapidly in both air and argon atmospheres. In contrast, Ag-on-TiO_x NPs that were heated to 500 °C in flowing argon or in a vacuum did not coarsen significantly and were remarkably stable. Ag-on-TiO_x NPs that were heated to 500 °C in air, however, behaved quite differently. The TiO_x crystallized upon heating and a significant loss of Ag were observed from the surfaces of the TiO_x, likely due to sublimation. These results demonstrate that the surface defect structure and chemistry of the oxide support strongly influence the thermal stability of Ag NPs produced by LAMA.     

Effects of thermally induced anatase-to-rutile phase transition in MOCVD-grown TiO2 films on structural and optical properties

Titanium dioxide (TiO₂) films with a thickness of 550 nm were deposited on quartz glass at 300 °C by metalorganic chemical vapor deposition. The effects of post-annealing between 600 °C and 1000 °C were investigated on the structural and optical properties of the films. X-ray diffraction patterns revealed that the anatase phase of as-grown TiO₂ films began to be transformed into rutile at the annealing temperature of 900 °C. The TiO₂ films were entirely changed to the rutile phase at 1000 °C. From scanning electron spectroscopy and atomic force microscopy images, it was confirmed that the microstructure of as-deposited films changed from narrow columnar grains into wide columnar ones. The surface composition of the TiO₂ films, which was analyzed by X-ray photoelectron spectroscopy data, was nearly constant although the films were annealed at different temperatures. When the annealing temperature increased, the transmittance of the films decreased, whereas the refractive index and the extinction coefficient calculated by the envelope method increased at high temperature. The values of optical band gap decreased from 3.5 eV to 3.25 eV at 900 °C. This abrupt decrease was consistent with the anatase-to-rutile phase transition. Received: 4 October 2000 / Accepted: 4 December 2000 / Published online: 23 May 2001     

Effect of calcination temperature on the morphology and surface properties of TiO2 nanotube arrays

Well-ordered TiO₂ nanotube arrays were prepared by electrochemical anodization of titanium in aqueous electrolyte solution of H₃PO₄ + NH₄F at a constant voltage of 20 V for 3 h, followed by calcined at various temperatures. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and Photoluminescence (PL) were used to characterize the samples. The results showed that the as-prepared nanotube arrays before being calcined were amorphous and could transform to anatase phase at a heat treatment temperature higher than 400 °C. As the calcination temperatures increased, crystallization of anatase phase enhanced and rutile phase appeared at 600 °C. However, further increasing the calcination temperature would cause the collapse of nanotube arrays. PL intensity of the nanotube arrays annealed at 500 °C was the lowest, which was probably ascribed to better crystallization together with fewer surface defects of the nanotube arrays.     

Effect of annealing treatment on the uniformity of CeO2/TiO2 bilayer resistive switching memory devices

Bilayer CeO₂/TiO₂ films with high-k dielectric property were prepared by rf magnetron sputtering technique at room temperature. Effect of annealing treatment on resistive switching (RS) properties of bilayer CeO₂/TiO₂ films in O₂ ambient at different temperature in the range of 350–550 °C was investigated. Our results revealed that the bilayer films had good interfacial property at 500 °C and this annealing temperature is optimum for different RS characteristics. Results showed that bilayer CeO₂/TiO₂ film perform better uniformity and reliability in resistive switching at intermediate temperature (i.e. 450 °C and 500 °C) instead of low and high annealing temperature (i.e. 350 °C and 550 °C) at which it exhibits poor crystalline structure with more amorphous background. Less Gibbs free energy of TiO₂ as compared to CeO₂ results in an easier re-oxidation of the filament through the oxygen exchange with TaN electrode. However, the excellent endurance property (>2500 cycles), data retentions (10⁵ s) and good cycle-to-cycle uniformity is observed only in 500 °C annealed devices. The plots of cumulative probability, essential memory parameter, show a good distribution of Set/Reset voltage.     

Synthesis of CdSe and CdSe/TiO2 nanoparticles under multibubble sonoluminescence condition

CdSe and CdSe/TiO₂ nanoparticles were synthesized under multibubble sonoluminescence (MBSL) condition. The influences of TiO₂ introduced as the sensitizer on the morphology and crystal transformation were investigated. The morphology, phase and optical properties of the final products have been characterized by X-ray powder diffraction, transmission electron microscope, UV-vis absorption spectroscopy and photoluminescence spectroscopy. The results showed that as-prepared nanoparticles are well-crystallized, and the suppression of crystal pattern transition as well as the control of CdSe crystal growth can be implemented by coupling of TiO₂ semiconductor. Furthermore, the possible growth mechanism for different morphologies and crystal phases of the nanocrystals were also discussed.     

Structural transformation study of TiO2 nanoparticles annealing at different temperatures and the photodegradation process of eosin-Y

Hydrothermal method was used to prepare TiO₂ nanoparticles with annealing temperature at 500 °C–700 °C. The mixture of anatase-rutile phase was investigated by powerful tool of X-ray diffraction (XRD). The structural parameters of anatase and rutile mixture phaseTiO₂ nanoparticles were calculated from the Rietveld refinement. The transformation rate of rutile was increased linearly with an annealing temperature of 500 °C–700 °C. The spherical morphology of the anatase and rutile mixed phase were obtained by scanning electron microscope and transmission electron microscope. The spherical particle of the anatase and rutile TiO₂ shows with great aggregation with different size and within the range of few tens nm. The EDAX study revealed the presence of titanium and oxygen. The best photocatalytic activity was identified as the 87.04% of anatase and 12.96% of rutile mixer phase of TiO₂. Various factors could be involved for a better photocatalytic activity.     

Oriented ZnO nanotubes arrays decorated with TiO2 nanoparticles for dye-sensitized solar cell applications

Dye-sensitized solar cells (DSSCs) based on a novel composite photoanode of TiO₂ nanoparticles coating on electrodeposited ZnO nanotube arrays are fabricated and characterized. An efficiency of 3.94 % is achieved for the composite cell, increasing 86.7 % than 2.11 % of the ZnO nanotubes cell. The short-circuit current (J _sc) and open-circuit voltage (V _oc) are also enhancing 52.9 % and 25.3 %, respectively. The improvements are because of the high surface area of TiO₂ nanoparticles, as well as fast electron transport and light scattering effect of ZnO nanotubes.     

Optoelectronics properties of TiO<Subscript>2</Subscript>:Cu thin films obtained by sol gel method

In this research, Cu-doped TiO₂ thin films have been successfully deposited onto a glass substrate by Sol–gel technique using dip coating method. The films were annealed at different annealing temperatures (400–500 °C) for 1 h. The structural, optical and electrical properties of the films were investigated and compared using X-ray Diffraction, UV–visible spectrophotometer and 4-point probe method. Optical analysis by mean transmittance T(λ) and absorption A(λ) measurements in the wavelength range between 300 to 800 nm allow us to determine the indirect band gap energy. DRX analysis of our thin films of TiO₂:Cu shows that the intensities of the line characteristic of anatase phase increasing in function of the temperature.     

Fabrication of Ag/TiO2 nanotube array with enhanced photo-catalytic degradation of aqueous organic pollutant

In this paper, the fabrication of Ag/TiO₂ nanotube arrays and their photo-catalytic activity have been studied. The SEM, TEM and XRD were performed to characterize the morphology and crystalline phase of the TiO₂ nanotube array and Ag/TiO₂ nanotube array. Ag nanoparticles with different loadings, which are aimed to suppress the electron–hole recombination so as to enhance the photo-catalytic oxidation efficiency, were systematically coated onto TiO₂ nanotubes. The photo-catalytic activity of these nano-materials was evaluated by the degradation of two different pollutants: methyl orange and glyphosate. The effects of various parameters, such as the amount of the photo-catalyst, the illumination time, and pH value on the photo-catalytic oxidation activity, were studied.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

Fabrication and characterization of CdS-sensitized TiO<Subscript>2</Subscript> nanotube photoelectrode

CdS quantum dot (Qd)-sensitized TiO₂ nanotube array photoelectrode is synthesised via a two-step method on tin-doped In₂O₃-coated (ITO) glass substrate. TiO₂ nanotube arrays are prepared in the ethylene glycol electrolyte solution by anodizing titanium films which are deposited on ITO glass substrate by radio frequency sputtering. Then, the CdS Qds are deposited on the nanotubes by successive ionic layer adsorption and reaction technique. The resulting nanotube arrays are characterized by scanning electron microscopy, X-ray diffraction (XRD) and UV–visible absorption spectroscopy. The length of the obtained nanotubes reaches 1.60 μm and their inner diameter and wall thickness are around 90 and 20 nm, respectively. The XRD results show that the as-prepared TiO₂ nanotubes array is amorphous, which are converted to anatase TiO₂ after annealed at 450 °C for 2 h. The CdS Qds deposited on the TiO₂ nanotubes shift the absorption edge of TiO₂ from 388 to 494 nm. The results show that the CdS-sensitized TiO₂ nanotubes array film can be used as the photoelectrode for solar cells.     

Influence of anodization parameters on the morphology of TiO2 nanotube arrays

TiO₂ nanotube arrays can be fabricated by electrochemical anodization in organic and inorganic electrolytes. Morphology of these nanotube arrays changes when anodization parameters such as applied voltage, type of electrolyte, time and temperature are varied. Nanotube arrays fabricated by anodization of commercial titanium in electrolytes containing NH₄F solution and either sulfuric or phosphoric acid were studied at room temperature; time of anodization was kept constant. Applied voltage, fluoride ion concentration, and acid concentrations were varied and their influences on TiO₂ nanotubes were investigated. The current density of anodizing was recorded by computer controlled digital multimeter. The surface morphology (top-view) of nanotube arrays were observed by SEM. The nanotube arrays in this study have inner diameters in range of 40-80 nm.     

Surface phenomena involved in the formation of Co nanoparticles on amorphous carbon and SiO2 deposited by magnetron sputtering

High-pressure DC magnetron sputtering was used for the deposition of cobalt on amorphous carbon (a-C) and SiO₂. Deposition conditions, substrate surface morphology and annealing parameters are investigated in order to promote the synthesis of large arrays of nanoparticles, with regular size and shape. Uniformly distributed Co nanoparticles a few nanometers in size were formed under annealing at 700°C in H₂. Particle nucleation and growth are discussed based on X-ray photoelectron spectroscopy, transmission and scanning electron microscopy and kinetic Monte Carlo modeling (KMC).     

Electrodeposition of Ag nanoparticles onto bamboo-type TiO2 nanotube arrays to improve their lithium-ion intercalation performance

Bamboo-type TiO₂ nanotube arrays prepared via anodic oxidation are modified with Ag nanoparticles by pulsed electrochemical deposition, for improved lithium-ion intercalation property as the anode material in lithium-ion batteries. Heat treatment converts as-formed nanotubes into anatase for Ag deposition. Bare and Ag-modified nanotubes are cycled at a current density of 800 μA?cm^?2 between 1.0 and 2.6 V (vs. Li/Li⁺). All Ag-modified nanotubes exhibit significantly improved or even doubled areal discharge capacities and better cycleability compared to bare nanotubes. Particularly, the nanotubes modified using 100 Ag deposition cycles deliver the highest initial discharge capacity of 199.6 μA?h cm^?2 and the largest final discharge capacity of 131.7 μA?h cm^?2 after 50 electrochemical cycles, while bare nanotubes exhibit an initial capacity of 93.5 μA?h cm^?2 and a final discharge capacity of 54.8 μA?h cm^?2. The former also exhibits 10 % higher capacity retention efficiency than the latter. In addition, an increase in the capacity of modified nanotubes is observed with more Ag deposition, but superfluous Ag content yields reduced capacities due to slower Li-ion transfer inside. Finally, kinetic characteristics of TiO₂ nanotubes are explored using cyclic voltammetry to understand the origin of improvements in electrochemical properties of Ag-modified nanotubes.