基于VPX总线的高速数字电路测试系统研究及应用

为解决战略预警雷达、舰载一体化等重点型号雷达中高速数字电路模块的维护能力,设计了基于VPX总线的高速数字电路自动测试系统,通过自研基于VPX总线的多功能测试模块、光纤测试模块,以及通用VPX背板,再结合通用的仪器设备构建测试系统,可兼顾多个型号雷达高速数字电路模块的测试。该系统可提供10路光纤通道,波特率最高为3.2Gbps;16路GPIO信号,中断响应时间＜50us;14路Rocket IO信号,传输速率2.5Gbps;4路*4Rapid IO信号,传输速率3.125Gbps。研究及实测结果表明该系统可解决基于VPX总线的高速数字电路模块的测试。     

Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.     

Design of wavelength adjustable lasers with photonic crystal based Fabry-Perot etalon for applications in optical network units of wavelength-division-multiplexed passive optical network systems

We propose a novel wavelength adjustable laser (WAL) with a photonic crystal based Fabry-Perot (FP) etalon. This laser will be a promising light source for optical network units (ONUs) of conventional wavelength-division-multiplexed passive optical network (WDM-PON) systems for up-stream transmission. It has the merits of a relatively simple fabrication and operation, wide process tolerance, low-cost, high side-mode suppression ratio, and wavelength-tunable characteristics. The optimization of the device structure and the implementation methods for this type of laser are discussed. Although the WALs in WDM-PON systems are not colorless, each laser can cover several wavelengths. Thus, the required number of different ONUs can be reduced. This approach may be necessary for 10 Gbps upstream transmission in next-generation optical access networks because the 10 Gbps data rate is difficult to achieve by using current colorless schemes.     

Performance analysis of symmetrical 10 Gbps colorless WDM-PON using subcarrier modulated downstream and wavelength converted upstream through RSOA

Here we have demonstrated a novel architecture of colorless wavelength division multiplexed-passive optical network (WDM-PON) and analyze its performance which is capable of transmitting 10 Gbps data symmetrically in both downstream and upstream. In this architecture downstream data is subcarrier modulated (SCM) using radio frequency (RF) as subcarrier and laser frequency as carrier with the help of a Mach–Zehnder modulator (MZM). For upstream data modulation an electro-absorption modulator, an optical coupler and reflective semiconductor optical amplifier (RSOA) are used. Upstream data is transmitted through wavelength conversion between pump wavelength and continuous wave light sent from central office (CO) using cross gain modulation (XGM) in RSOA. Pump wavelengths have separate wavelength band than the carrier's wavelength sent from optical network unit (ONU) and can be chosen any one in its band. Since carrier reuse scheme is implemented so all the ONUs are operates in colorless mode. Effect of ER of delay interferometer (DI) on output OCSR of DI for different input OCSR is performed for SCM data. Simulation is performed with all 16 downlink and 16 uplink channels having data rate of 10 Gbps having acceptable performance.     

400 Gbps WDM transmission over short range with discrete multi-tone

We simulate 400 Gbps WDM transmission system with DMT modulation. The system reaches 5 km SSMF with 100 Gbps per wavelength when the BER is 1e−3. From our analyses, we can see that DMT can be a promising solution for high capacity optical transmission system over short distance.     

Enhanced colorless and broadcast capable symmetrical 10-Gbps bidirectional transmission in WDM-PON using RSOA and EAM

Here we proposed a novel architecture of wavelength division multiplexed-passive optical network (WDM-PON) in which the downlink unicast data, broadcast data and uplink unicast data transmission is possible with the symmetric data rate of 10 Gbps. At remote node (RN) cyclic wavelength routing property of array waveguide grating (AWG) and power splitting capacity of power splitter is used in the architecture so that broadcast channel can be overlaid on downlink unicast channels. At ONU carriers sent from central office (CO) is reused for upstream data transmission with the help of integration of a reflective semiconductor amplifier (RSOA) and an electro-absorption modulator (EAM) so there is no need of extra laser sources at ONUs which makes them colorless. EAM can be operated at very high speed; a modulation bandwidth of tens of GHz can be achieved. Broadcast channel causes a limited interference with downlink and uplink unicast channels so it does not affect the system performance. Since each channel has different wavelength so NRZ data is used which eliminates expensive DPSK receivers and detection becomes very easy. Simulation is performed with all channels having data rate of 10 Gbps having acceptable performance.     

一种新型波长转换器的模块化设计

对一种新型结构全光波长转换器进行了高精度、高稳定度的模块化设计，并利用该模块实现对波长转换器参数的监控。结果表明这种新型模块对波长转换器的实现提供了可靠的保证，表现出较高的稳定度和实用性。     

Comparison of various dispersion compensation techniques at high bit rates using CSRZ format

In this paper, the dispersion compensation techniques are compared on the basis of eye opening, eye closure, bit error rate and Q-factor. These techniques are applied to CSRZ system, which operates at bit rates of 2.5, 5, 10, 15 and 20 Gbps bit rates. The technique using fiber Bragg grating (FBG) for dispersion compensation is the best technique as this technique gives larger values of eye opening at 10 and 20 Gbps bit rate, smaller values of eye closure at 10 and 20 Gbps, minimum value of BER at 15 Gbps and maximum value of Q-factor at 15 Gbps when compared with other techniques. The RDF technique is the next best technique since this technique gives maximum value of eye opening when other techniques give almost similar values of eye opening at 15 Gbps, minimum value of eye closure at 15 Gbps, minimum value of BER at 15 Gbps and maximum value of Q-factor at 15 Gbps when compared with other techniques. The DCF is the next best technique as this technique gives maximum and minimum values of eye opening and eye closure at 20 Gbps (next best to FBG at 20 Gbps).     

基于量子点半导体光放大器全光波长变换特性

从光电集成电路的角度出发,根据量子点半导体光放大器(QD-SOA)中载流子跃迁速率方程和光场传输方程,建立了QD-SOA等效电路模型,并通过电路仿真的方法对QD-SOA的增益谱、饱和增益特性等进行了仿真和分析;利用QD-SOA的交叉增益调制研究了速率分别为40Gbps、100Gbps和160Gbps时的波长转换特性,并分析了不同的偏置电流、功率的信号光和探测光对输出信号消光比和Q值的影响,其转换速率可达到100Gbps,消光比ER约为10dB,Q值约为2.2.该研究对提高基于QD-SOA的交叉增益调制波长转换的性能具有指导意义.     

4.25 Gbps小型可热插拔光收发模块的设计与测试

对4.25 Gbps小型化可热插拔(SFP)光收发模块的关键参数进行了理论分析,从发射、接收和控制3个方面讨论了模块的结构组成,设计出了符合SFP MSA及SFF-8472协议的光模块,并根据此设计方案制作了样品模块。在-40,25,85 ℃环境温度下测试和分析了模块的性能指标,结果显示其光功率、消光比和灵敏度等均符合设计要求,且在适用温度范围内表现出良好的稳定性。实验证实了方案的可行性,为模块的产品化提供了参考。     

Wavelength conversion based on high nonlinear microstructured fiber

A wavelength conversion based on high nonlinear microstructured fiber is demonstrated. Core diameter and pitch of the microstructured fiber used in this wavelength conversion method are 2.05 μm and 5.0 μm, respectively. Diameter of the air-holes in the fiber cladding is 4.50 μm, the nonlinear coefficient of the microstructured fiber is 112.2 W^?1 km^?1 and it is 60 times higher than that of a conventional dispersion-shift fiber, the length of the fiber is 100 m. Four-wave-mixing effect is improved in the high nonlinear microstructure fiber and then the efficiency of the wavelength conversion is improved also. 10 Gbps Not-Return-to-Zero (NRZ) modulation format and 10 Gbps Return-to-Zero (RZ) modulation format are converted effectively by our method. This study can provide a new alternative solution for high effective all-light wavelength conversion in high speed optical communication systems with multi-wavelengths and all-light optical networks.     

50 km bidirectional FTTH transmission comparing different PON standards

In this paper, a bidirectional Fiber To The Home (FTTH) is proposed where WDM transmitter is used as a seeding source with wavelength of 1550 nm. The system utilizes a Travelling wave Semiconductor Optical Amplifier (TSOA) with injection current 0.15A. 50 km range FTTH architecture is demonstrated for both downstream and upstream channels. We investigated the impact of different data rates on upstream and downstream data. The BER results show that the performance of our scheme is good for 10 Gbps system for downstream transmission as it accommodates 64 ONUs. From simulation results show the BER of 9.95e-009 is reported at 15 Gbps but only in case of 32 ONUs. Similarly, in case of upstream transmission, Q-Factor of 15.04 dB is reported for 32 ONUs. So this scheme is a practical solution to meet the data rate of the optical links simultaneously in tomorrow's PON access networks.     

Investigation of Hybrid Optical Amplifiers for Dense Wavelength Division Multiplexed System with Reduced Spacings at Higher Bit Rates

Abstract

This article proposes various combinations of optical amplifiers for a dense wavelength division multiplexed system and investigates the impact of reduced channel spacing at high bit rates in terms of quality factor, bit error rate, eye closure, and output power. It is reported that the hybrid optical amplifier (Raman–erbium-doped fiber amplifier [EDFA]) provides better results with a maximum covered single span distance (220 km) at channel spacing of 6.25 GHz. The maximum acceptable bit rate for the 12.5-GHz channel spacing dense wavelength division multiplexed system is also investigated, and the recommendation is provided that for the Raman–EDFA, Raman–EDFA–Raman, EDFA–Raman–EDFA, and EDFA–semiconductor optical amplifier–EDFA, the operating bit rate should not be greater than 20, 16, 19, and 20 Gbps, respectively.     

High-Speed Optical Packet Switch with an Optical Digital-to-Analog Conversion-Type Header Processor

We describe a novel type of an optical packet switch with an optical header processor based on optical signal processing and wavelength routing architecture. It consists of an optical digital-to-analog conversion-type header processor, wavelength selection portion with an electrically tunable laser, a wavelength converter based on a semiconductor optical amplifier (SOA), and wavelength routing by use of an arrayed waveguide grating (AWG), which is called a wavelength label switch (WLS). Wavelength switching of an electrically tunable laser, and wavelength conversion were successfully achieved within a few nanoseconds after recognition of an optical header using a two-bit optical header processor and a FPGA-based wavelength table. High-speed transfer performance of less than a few tens of nanoseconds and BER of less than 10^-10 were verified in the wavelength routing operation among three assigned wavelengths.     

Simulation and analysis of dispersion compensation schemes for 100 Gbps PDM–OFDM optical communication system

In this paper, the implementation of 100 Gbps optical communication system exploiting polarization diversity at transmitter and receiver is developed and investigated with pre-, post- and symmetrical dispersion compensation schemes by using dispersion shifted and dispersion compensated fibers through simulations to optimize high data rate optical transmission. Motivation to the current analysis is to compare all 3 compensation schemes and it's found that the pre compensation technique is superior to post and symmetrical compensation techniques in 100 Gbps PDM–OFDM communication system. On examination of symmetrical and post dispersion compensation schemes, it's found that the later is superior to the previous in this case. A 100 Gbps coherent optical OFDM workplace has been discovered in which two 50 Gbps data streams are combined into one wavelength by polarization beam combiner. By comparing one can get a promising system to the symmetrical high capacity access network with high spectral efficiency, cost effective, good flexibility.     

用于10GbpsTD-LTE的光接收器件的研究

针对目前TD-LTE产业的迅速发展,市场需求日益增大,对所用的10Gbps SFP+光收发合一模块在技术和成本上也提出了更高的要求。介绍了一款应用于10Gbps TD-LTE的光接收器件的设计,并对封装后的器件进行了测试及分析。该接收器件整体光电性能良好,同时具备低成本和低功耗的优势。     

7.13 W全固态1 319 nm宏微脉冲激光器

 研制了一台高效率全固态平均功率7.13 W的1 319 nm宏微脉冲激光器。激光器采用热稳Z形折叠腔,增益模块采用自行研制的准连续15个二极管芯片环形泵浦的Nd:YAG模块,采用主动声光锁模器作为锁模元件,并在腔内插入倍频KTP晶体对激光器的输出尖峰进行抑制。为了获得稳定的锁模状态,对激光器腔长进行了精确设计和调节。当激光器腔长与锁模器驱动频率匹配时,获取了宏脉冲重复频率400 Hz、脉宽约190 μs,微脉冲重复频率95.6 MHz、脉宽小于1.0 ns的1 319 nm激光脉冲。     

Wavelength stabilized 980 nm uncooled pump laser modules for erbium-doped fiber amplifiers

We review the development of wavelength stabilized 980 nm pump laser modules without active temperature stabilization for applications in erbium-doped fiber amplifiers. Operation over a wide temperature range with an output power exceeding 400 mW at an ambient temperature of 70°C is demonstrated. The overall reliability of uncooled modules is estimated to be well below 500 FIT at all operating conditions. Such devices are made possible by continuous development and steady improvement of the pump laser chip, the optimization of the fiber Bragg grating stabilization scheme, careful design of the module package, and extended reliability analysis on the basis of stress tests as well as field data.     

紫外双光栅光谱仪结构设计与波长精度分析

为了满足太阳光谱在170～380 nm波段的精确观测需求,设计了波长重复性精度优于±0.02 nm的紫外双光栅光谱仪。波长扫描机构是双光栅光谱仪的关键组件,根据凹面光栅色散原理,将光学设计指标转换为波长扫描机构设计的输入参数,分析了影响光谱仪波长重复性精度的误差源。根据分析结果得知,丝杠的重复定位误差是影响波长重复性的主要误差源。选用重复定位精度为±2μm的丝杠设计了波长扫描机构,并对光谱仪整机进行了设计。以汞灯光源对光谱仪的波长重复性指标进行了验证实验。实验结果表明,设计的光谱仪波长重复性介于-0.005～+0.007 nm之间,满足波长重复性优于±0.02 nm的指标要求。     

10 Gbps optical soliton transmission link using in-line SOA on standard SMF at 1.3 μm

In this paper, 10 Gbps optical soliton transmission link using in-line semiconductor optical amplifiers (SOAs) for already installed standard single mode fibers (SMF) at 1.3 μm wavelength has been reported. The pattern effect and the impact of chirp on pulse propagation after amplification have been investigated. The observations are based on modeling and simulation optical soliton transmission link. Optical soliton pulse transmission over distances of the order of several hundreds of kilometers has been shown with and without initial chirp.