Tween-80–n-Butanol–Diesel–Water Microemulsion System—A Class of Alternative Diesel Fuel

Tween-80–n–butanol–diesel–water microemulsion systems with various surfactant:cosurfactant (S:C) ratio have been reported as a class of alternative diesel fuel from their phase behavior, clouding phenomena, conductivity, turbidity, and inflammation studies. Temperature induced clouding of microemulsion containing 2% brine at an S:C ratio of 1:1 from a suitable turbid zone has been examined to see the stability of the diesel–water microemulsion systems. Regression models have been proposed to understand the impact of various components of the microemulsion on their cloud point (CP) values. Conductivity of the microemulsions at various S:C ratio increases with the volume of brine having two cut points depicting the presence of three microheterogenous phases within the system, whereas turbidity shows a linear increase. Dye-probed investigation of water-rich and oil-rich zones of the microemulsions indicates the involvement of a dynamic mass transfer process within the various zones. The intensities of flames produced during burning of the microemulsions with various O:E:W weight percentages selected from the isotropic regions of the phase diagrams have been estimated using MATLAB image processing method and the impacts of various components on the fuel use of the microemulsions have been analyzed.     

Water-Diesel Microemulsions Stabilized by an Anionic Extended Surfactant and a Cationic Hydrotrope

Alcohol-free microemulsions were formulated using mixtures of extended surfactant (C_12-14-PO₁₄-EO₂SO₄Na), sodium dodecyl benzene sulfonic acid and cationic hydrotropes with equal amounts of water and diesel. The cationic hydrotropes had short hydrocarbon or propylene oxide chain. The formulation included sodium carbonate to convert naphthenic acids in diesel to soaps. The phase behavior at ambient temperature of oil-free mixtures as a function of NaCl concentration was investigated. Visual inspection as well as cross polarizers were used to detect anisotropy. The microemulsion fish phase diagram and solubilization ratios for diesel and brine in the middle phases were determined. The minimum surfactant concentration needed to initiate middle phase formation was 0.10 wt%.

Salinity scans revealed that optimal salinity can be adjusted according to the hydrophilic/lipophilic nature of the hydrotrope used. Interfacial tension measurements using a spinning drop tensiometer showed a minimum value of 0.0015 mN/m between middle phase microemulsion and excess brine and a value of 0.032 mN/m between diesel and brine.     

Oleate Ester-Derived Nonionic Surfactants: Synthesis and Cloud Point Behavior Studies

The synthesis and cloud point behavior of high oleate ester-derived nonionic surfactants are now reported. The effect of various polyethoxylate chain lengths (polyethylene glycol with 7, 11, and 16 units of ethylene oxide (EO) monomer) as the surfactant's hydrophilic head on the cloud point was investigated. The effect of varying amounts of sodium chloride and five different ionic surfactants on the cloud points of the synthesized nonionic surfactants were also presented. When the chain length of polyethoxylate increased, the cloud point of the synthesized nonionic surfactant also increased, ranging from 16°C, 43°C, and 64°C for 7, 11, and 16 EO units, respectively. Increments in sodium chloride concentration depressed the cloud point values of the synthesized nonionic surfactants linearly. The addition of ionic surfactants elevated the cloud points of the synthesized nonionic surfactant. However, in the presence of sodium chloride, the cloud point of the mixed ionic-nonionic solution was suppressed and anincrease in ionic surfactant concentration was required to elevate the cloud point. It was also found that the cloud points of synthesized surfactants can be raised up to 95°C in the presence of 4wt% NaCl solution.     

Study of Interactions and Association Thermodynamics Between Sudan Red and Sodium Dodecyl Sulfate in Microemulsions

The absorption spectrum of Sudan red III (SR) in oil solutions and a series of O/W microemulsion with surfactant sodium dodecyl sulfate (SDS) has been determined by the UV-Vis spectrophotometer. We found that an association interaction existed between the stain SR and anionic surfactant SDS in water/mixed oil/SDS microemulsions. By measuring the absorbance of Sudan red in a series of microemulsions which has different R values and using the appropriate association models to analyze the experimental data, we obtain the association constants of SR and SDS, and the values of thermodynamics functions of associationΔ_r G _m has also been calculated from the association constants.     

Hydrophilic alcohol ethoxylates as efficiency boosters for microemulsions

Highly amphiphilic polyalkane-PEO diblock copolymers drastically increase the solubilization capacity of surfactants in microemulsions if they are used in small quantities as additive to the surfactant. This effect goes along with an additional reduction of the already very low interfacial tension between water and oil. Lamellar phases, which usually develop when the surfactant becomes more efficient, are suppressed to a large extent. In this work we use another type of additive, namely hydrophilic alcohol ethoxylates. These amphiphiles are identical with the previously used block copolymers with respect to the hydrophilic moiety. However, they contain only small hydrocarbon groups ranging from C8 to C18. A typical example from the hydrophilic alcohol ethoxylates is C12E100. Both additive types increase surfactant efficiency equally with respect to mass fraction in the mixture. Because the alcohol ethoxylate additives decorate the surfactant film only on the aqueous side, they influence the curvature of the surfactant membrane or, in other words, the temperature behavior of the microemulsion. Together with nonionic surfactants, however, the shift of the one-phase region to higher temperatures is only a few degrees Celsius. Just as with the polyalkane-PEO block copolymers, the hydrophilic alcohol ethoxylates suppress lamellar phases. This behavior is especially pronounced if the hydrophobic groups are small or the PEO chains are long. We found that hydrophobic units as short as C 8 are sufficient to largely anchor the PEO chains at the interface. If C12 or C18 hydrocarbon unit are used instead, the PEO chains are fully interfacially active, even if the hydrophilic chain contains up to about 500 EO units. We applied the new additives in bicontinuous and in droplet microemulsions and used nonionic, as well as ionic, surfactants, namely C10E4 and AOT. In contrast to polyalkane-PEO blockcopolymers the new additives are easy to synthesize and are commercially available. Therefore, they might be interesting in applications.     

Influence of Glycerol and Temperature on the Phase Behavior and Micellization of CTAB and SDS in Aqueous Solutions

In this work the micellization of sodium dodecylsulfate (SDS) and cetyltrimethyammonium bromide (CTAB) in water-glycerol mixed solvent have been investigated at 25, 35, and 45°C, respectively. The micellization of both surfactants in pure water at different temperatures has also been studied. The phase diagrams of the surfactants in water-glycerol mixed solvent were also established. From the conductivity measurements, the critical micelle concentration (CMC) and the degree of counterion dissociation (β) were obtained as a function of glycerol-water ratio and temperature. Standard free energy of micellization (ΔG°_mic) as a function of glycerol contents and temperature was calculated and discussed. It has been found that the micellization of the two surfactant in solutions with glycerol at 25°C and in pure water at higher temperatures are not the same although they have equal dielectric constants values.     

Synthesis of a New CO2 Philic Surfactant for Enhanced Oil Recovery Applications

The synthesis of CO₂ philic surfactant using maleic anhydride and 4-tert-butylbenzyl alcohol is reported. We reacted maleic anhydride with 4-tert-butylbenzyl alcohol to form bis(4-(tert-butyl)benzyl) fumarate and sulfonated the produced diester. The esterification reaction was optimized for a maximum yield of 98% of bis(4-(tert-butyl)benzyl) fumarate. First-order reaction kinetics with respect to acid was observed. The activation energy was found to be 55.62 kJ/mol. The sulfonated product of diester was obtained by the sulfonation reaction and the yield of 82% of surfactant was achieved. The in-house developed surfactant effectively lowered down the IFT between CO_2/brine to 4.2 mN/m. This surfactant is targeted for CO₂-EOR applications.     

Effect of Ionic Surfactants on the Adsorption of Quercus infectoria Natural Dye on Cotton Fiber: A Kinetic Study

The adsorption kinetics of Quercus infectoria natural dye on cotton in the absence and presence of the cationic (cetyl trimethyl ammonium bromide; CTAB) and anionic (sodium lauryl sulfate; NaLS) surfactants has been investigated at three temperatures, namely, 40°C, 50°C, and 60°C. On increasing the surfactant content in the surfactant-dye mixture, the initial rate of adsorption (h _i) and the adsorption capacity at equilibrium (q _e) were found to increase while pseudo-second-order rate constant (k ₂) was found to decrease. The retarding effect of surfactant on k ₂ was in order of CTAB > NaLS. The activation parameters for adsorption process have been evaluated in each case, and the mechanism of adsorption process has been discussed.     

Lamellar Liquid Crystals Formed in Ternary DEP/Oil/Water Systems

Lamellar liquid crystals of the nonionic surfactant dodecyl polyoxyethylene (4) polyoxypropylene (5) ether (DEP) were investigated by means of phase diagram and rheological technique at 25°C in the presence of different solvents. The aqueous medium includes pure water, physiological saline and 20% sucrose solution, and the oil phase includes isopropyl myristate (IPM), oleic acid, and geraniol, which are all pharmaceutically accepted chemicals. The steady and dynamic rheological property analyses of the lamellar liquid crystals formed in DEP/H₂O/IPM system indicate that the lamellar samples constructed by this special surfactant behave as pseudo-plastic fluid with relatively high elasticity and possess defects in their assembled structure. Also in this system, the elastic character gets decreased with increase in the water content. Furthermore, the comparison investigations show that the relatively high polar oil component increases the network strength of the lamellar phase, while increase in the polarity of water phase enhances the structure defects.     

Influence of Surfactants Synergism on the Adsorption Behavior at Air/Water and Solid/Water Interfaces

The influence of synergistic interaction between sodium dodecylsulfate (SDS) and N,N-dimethyldodecan-1-amine oxide (DDAO) on their adsorption at air/water and solid/water interfaces at 20°C is investigated. The critical micelle concentration values obtained from surface tension measurements indicated strong synergism between SDS and DDAO, according to regular solution model. The excess surface concentration (Γ) and the minimum occupied area by single and mixed surfactant monomers (A_min) at liquid/air interface were also calculated. The adsorption onto the activated charcoal and silica was then measured to find out the correlation between surfactant synergism and their adsorption at solid/water interface. The amounts of surfactant adsorbed onto 1 wt% activated charcoal follow the trend: SDS/DDAO > DDAO > SDS. SDS molecules do not adsorb onto 5 wt% silica substrate, while SDS/DDAO mixed system was found to have the highest adsorption behavior. The obtained indicate that SDS can be removed from water by mixing it with amphoteric surfactant.     

FORMULATION OF MODEL CUTTING-OIL WATER EMULSIONS USING PARAFFINIC OIL AND IONIC/NONIONIC SURFACTANT MIXTURE.

Cutting-oil emulsions are marketed under the shape of concentrates that the user has to dilute. More often these concentrates are monophasic microemulsions. We show that this kind of microemulsions may be obtained while relying on the generalized concept of Winsor, which guides the manipulation of three formulation parameters, which in turn rationally modify the surfactant interactions with the oily and the aqueous phases.

The model concentrates that we have formulated contain six constituents. The oily phase is constituted of paraffinic oil and normal decanol. The aqueous phase is a solution of monoethanolamine borate in water whose hardness is fixed at 40°f. The active mixture contains a hydrophilic surfactant and a lipophilic surfactant.

We have formulated concentrates presenting an excellent ability to dilution, a very good stability to the hardness of water and pHs in agreement with the cutting fluid specification sheets, while identifying the formulation parameters to the mass ratio of normal decanol in the oily phase, to the mass ratio of monoethanolainine borate in the aqueous phase and to the mass ratio of the hydrophilic surfactant in the active mixture.     

Regioselective Nitration of Phenols in O/W Microemulsion by NaNO3 and Dilute Sulfuric Acid

Highly regiospecific mononitration of phenol by NaNO₃ and dilute sulfuric acid was carried out in a TX100 oil-in-water microemulsion. Effects of various parameters such as acid type, surfactant concentration, water content, and alcohol have been investigated. The use of inexpensive and relatively nontoxic acidic reagent is an advantage of this method.      

Multi-Walled Carbon Nanotubes as a Cosurfactant for Highly Concentrated Emulsions

The role of multi-wall carbon nanotubes (MWCNT) as a solid surfactant in highly concentrated water-in-oil emulsions was investigated. MWCNT were dispersed in the oil phase. These suspensions are viscoplastic fluids with the yield stress increasing by more than 1000 times with addition of 2% MWCNT, which demonstrates intensive “structurizing” ability. After emulsion preparation, MWCNT were concentrated at the interface, stabilizing emulsions. The dependence of the inversion point on MWCNT concentration was found. Emulsions containing up to 94 wt% of the aqueous phase can be prepared only when MWCNT is combined with conventional surfactant. Rheological properties of such compositions were measured. It was established that emulsions stabilized by a combined surfactant were more stable in comparison to conventional surfactant stabilized emulsion.     

Novel Surfactant for the Reduction of CO2/Brine Interfacial Tension

The synthesis of novel CO₂ philic surfactant using maleic anhydride and dipropylene tertiary butyl alcohol is reported. The synthesis involved the esterification of maleic anhydride to produce bis(2-(2-(tert-butoxy)propoxy)propyl) maleate and subsequent sulfonation of the esterified product. Para toluene sulfonic acid was employed as catalyst for the esterification reaction. The esterification reaction was optimized for the maximum yield of 98% of bis(2-(2-(tert-butoxy)propoxy)propyl) maleate. The esterification reaction kinetics employing heterogeneous catalyst were also studied. Although this is a bimolecular reaction, a first order reaction kinetics with respect to acid has been observed. The activation energy was found to be 58.71 kJ/mol. The diester was followed by the sulfonation process and a yield of 85% of surfactant was achieved. The synthesized surfactant successfully lowered down the IFT between CO_2/brine to 1.93 mN/m. This surfactant has a great potential to be used for CO₂-EOR applications.     

Synthesis and Evaluation of New Demulsifiers Incorporating Linear Alkyl Benzene Moiety for Treating Water-in-Oil Emulsion

In the present study, five types of water soluble demulsifiers based on linear alkyl benzene were prepared. The chemical structures of the prepared demulsifiers were elucidated using Fourier transform-infrared (FTIR) and ¹H NMR spectra. Different factors affecting demulsification efficiency such as; water content, demulsifier concentration, hydrophilic lipophilic balance (HLB), and ethylene oxide unit were investigated. Also, the rheological properties in relation to demulsification efficiency were studied. The surface and thermodynamic parameters of the prepared demulsifiers were determined at 25°C including, surface tension (γ) and effectiveness, maximum surface excess (Γ_max), and minimum surface area (A_min). From the obtained data, it was found that the demulsification efficiency increases with increasing the water content and concentration of the demulsifiers. Primarily evaluation study of demulsification performance of the new demulsifiers showed that as the ethylene oxide unit in the demulsifiers increase (10–40 ethylene oxide units), the performance of the demulsifiers increasing, however, it decrease in case of demulsifiers with (80 ethylene oxide unit).     

Kinetics and Equilibria of Synthesized Anionic Surfactant onto Berea Sandstone

We present static adsorption studies of anionic surfactants on crushed Berea sandstone. The maximum adsorption density was 0.9604 mg/g. The kinetics of adsorption process was modeled using pseudo-first-order and pseudo-second-order rate equations at 25°C and 70°C. The equilibrium adsorption process was validated using Langmuir and Freundlich adsorption models. In addition, the effects of different parameters that govern the effectiveness of these surfactants such as pH and temperature were also investigated. The kinetic study results show that the surfactant adsorption is a time dependent process. The apparent rate constant of adsorption process determined by the first-order kinetic model at 25°C and 70°C were 0.11768 and ?0.04513, respectively. The rate constant for pseudo-second-order kinetic model was 0.0086 at 25°C and 0.0101 at 70°C. The adsorption of anionic surfactant followed pseudo-second-order kinetic model. The Freundlich and Langmuir model constant were 1.6509 × 10^?4 and ?9.775 × 10^?5, respectively. The equilibrium results showed that the adsorption of anionic surfactant onto Berea sandstone was well described by Langmuir adsorption model. It was concluded that anionic surfactants performed better at higher pH and temperature.