Wetting properties of aqueous solutions of hydrophobically modified inulin polymeric surfactant

The contact angles of aqueous solutions of a polymeric surfactant namely hydrophobically modified inulin (INUTEC®SP1) were measured on hydrophilic and hydrophobised quartz glass surfaces using the sessile drop technique. These measurements showed a large difference (>10°) between the advancing contact angle θ ₁ (that is measured immediately after placing the drop on the surface) and the constant contact angle θ ₂ (that is measured 30 minutes after placing the drop). In all the results only the contact angle θ ₂ was subsequently measured. θ versus INUTEC®SP1 concentration C _s curves were obtained at various NaCl concentrations both on hydrophilic and hydrophobic glass surfaces. On hydrophilic glass surface the θ versus C _s curves showed a maximum at a concentration range of 10^–6 to 2?×?10^–5 mol dm^-3 INUTEC®SP1. These curves were shifted to lower values as the NaCl concentration was increased. On such hydrophilic surface the INUTEC®SP1 molecule adsorbs with the polyfructose loops and tails oriented towards the surface leaving the alkyl chains in solution. Saturation adsorption with this orientation occurs at 2?×?10^–5 mol dm^-3 INUTEC®SP1. However, the contact angles remain quite small (<18°) indicating the presence of several hydrophilic glass patches uncovered by surfactant molecules. At C _s?>?2?×?10^–5 mol dm^-3 θ decreases with further increase of the INUTEC®SP1 concentration reaching 5° at the Critical Association Concentration (CAC) of the polymer. This indicates the formation of a bilayer of INUTEC®SP1 molecules with the alkyl chains hydrophobically attached to those of the first layer. On a hydrophobic glass surface, adsorption of INUTEC®SP1 occurs by multi-point attachment with the alkyl chains on the surface leaving the hydrophilic polyfructose loops and tails dangling in solution. This results in a gradual decrease of the contact angle with increase in INUTEC®SP1 concentration, reaching a plateau value (>85°) between 2?×?10^–5 and 2?×?10^–4 mol dm^-3. The large contact angles obtained on adsorption of the polymeric surfactant on a hydrophobic surface indicate the presence of several uncovered hydrophobic patches. These results give a reasonable picture of the adsorption and orientation of the INUTEC®SP1 molecules on both hydrophilic and hydrophobic solid surfaces.     

纳米SiO2与阳离子表面活性剂的相互作用及其诱导的正辛烷-水乳状液的双重相转变

研究了3种不同结构的水溶性阳离子表面活性剂对纳米二氧化硅颗粒的原位表面活性化作用, 它们分别是单头单尾的十六烷基三甲基溴化铵(CTAB)、单头双尾的双十二烷基二甲基溴化铵(di-C12DMAB)和双头双尾的Gemini型阳离子三亚甲基-二(十四酰氧乙基溴化铵)(II-14-3), 并通过测定Zeta电位、吸附等温线及接触角等参数对相关机理进行了阐述. 结果表明, 阳离子表面活性剂吸附到颗粒/水界面形成以疏水基朝向水的单分子层, 从而增强了颗粒表面的疏水性是原位表面活性化的基础. 通过吸附CTAB和II-14-3, 颗粒的疏水性适当增强, 能吸附到正辛烷/水界面稳定O/W(1)型乳状液; 而通过吸附di-C12DMAB所形成的单分子层更加致密, 颗粒的疏水性进一步增强, 进而使乳状液从O/W(1)型转变为W/O型; 当表面活性剂浓度较高时, 由于链-链相互作用, 表面活性剂分子将在颗粒/水界面形成双层吸附, 使颗粒表面变得亲水而失去活性, 但此时体系中游离表面活性剂的浓度已增加到足以单独稳定O/W(2)型乳状液的程度. 因此当采用纳米二氧化硅和di-C12DMAB的混合物作乳化剂时, 通过增加di-C12DMAB的浓度即可诱导乳状液发生O/W(1)→W/O→O/W(2)双重相转变.     

The wettability of polytetrafluoroethylene and polymethyl methacrylate by aqueous solution of two cationic surfactants mixture

Advancing contact angle (theta) measurements were carried out for aqueous solutions of cetyltrimethylammonium bromide (CTAB) and cetylpyridinium bromide (CPyB) mixtures on polytetrafluoroethylene (PTFE) and polymethyl methacrylate (PMMA). The obtained results indicate that the wettability of PTFE and PMMA by aqueous solutions of CTAB and CPyB mixtures depends on the composition and concentration of the mixture; however, synergism in the wettability does not exist. In the range of low concentrations of aqueous solution mixtures there is a linear dependence between the contact angle and composition of the mixtures, but at a concentration close to CMC a deviation from linear dependence is observed. In contrast to Zisman, there is no linear dependence between costheta and the surface tension of aqueous solution of CTAB and CPyB mixtures, but a linear dependence exists between the adhesional and surface tension, and these lines have a slope -1 and -0.34 for PTFE and PMMA, respectively, which suggests that adsorption of CTAB and CPyB mixtures at water-air and PTFE-water is the same, and the orientation of the CTAB and CPyB molecules at both interfaces in the saturated monolayer should also be the same. Adsorption of these mixtures at water-air interface is considerably higher than at PMMA-water interface, and CTAB and CPyB molecules should be parallelly oriented to PMMA surface in the saturated monolayer. Extrapolation of the straight lines to the points corresponding to the surface tension of aqueous solution, which completely spreads over the PTFE and PMMA surface, gives a critical surface tension of wetting equal to 23.44 and 33.13 mN/m, respectively. The value of 23.44 mN/m is higher than that of the surface tension of PTFE, but the value of 33.13 is lower than that of Lifshitz-van der Waals components of PMMA surface tension. On the basis of the critical surface tension, the surface tension of PTFE and PMMA, the Young equation, and thermodynamic analysis of the adhesion work of aqueous solution of surfactant to polymer surface, it was found that for PTFE and PMMA the changes of the contact angle of aqueous solution of two cationic surfactants mixtures on their surfaces as a function of the solution concentration resulted only from the decrease of the polar component of the solution surface tension.     

Wetting behavior of pulmonary surfactant aqueous solutions

The wetting properties of pulmonary surfactant aqueous solutions with respect to solid surfaces with different degree of hydrophobicity have been studied. The contact angles θ of drops from a pulmonary surfactant solution onto SiO₂-glass surfaces have been measured as a function of their degree of hydrophobicity θ _w. The completely hydrophilic SiO₂-glass surface is essentially hydrophobized by the animal-derived pulmonary surfactant Curosurf. The hydrophobization depends on the surfactant concentration—the contact angles increase with increasing the Curosurf concentration C _s in the low concentration range, but they remain almost constant in a wide range of C _s >90 μg/ml. Additions like NaCl and bovine serum albumin influence the θ-values. The contact angles θ naturally increase with increasing θ _w but this dependence is not linear—the curve steepens at larger θ _w values. The thickness h of the wetting thin liquid films from Curosurf aqueous solutions depends on the hydrophobicity θ _w of the solid surface and the h(θ _w) curves always pass a minimum. The h-values, as well as the h(θ _w) curve, are mainly determined by the steric and hydrophobic disjoining pressures, which depend on the orientations and conformations of the molecules adsorbed on the solid surface from the very complicated multi-component aqueous solutions.     

Rheological behavior of aqueous suspensions containing cationic starch and aluminum magnesium hydrotalcite-like compound in the presence of different electrolytes

The rheological properties of aqueous suspensions consisting of cationic starch (CS) and positively charged aluminum magnesium hydrotalcite-like compound (HTlc) in the presence of different electrolytes (NaCl, CaCl₂ and AlCl₃) were investigated. It is found that the network-like structure of pure CS solution is formed by the interaction between CS molecules. Both the equilibrium viscosities and the elastic response of CS solution decrease with the addition of NaCl, CaCl₂ and AlCl₃. Small amplitude sinusoidal oscillation tests show that a three-dimensional network of the HTlc/CS suspension can be formed through the bridge effect between CS molecules and HTlc particles due to the hydrogen bonding between the ether groups or hydroxyl groups of CS and the hydroxyl groups of HTlc. Both the equilibrium viscosity and dynamic property of the HTlc/CS suspensions indicate that the network-like structural strength of the suspensions increases firstly and then decreases with increasing HTlc content. The equilibrium viscosity and the elastic response of the HTlc/CS suspensions decrease gradually with the addition of NaCl or CaCl₂, but decrease firstly then increase and then decrease with increasing AlCl₃ concentration, i.e., the structural strength of the HTlc/CS suspensions can be strengthened by the addition of appropriate amount of AlCl₃ content.     

Effect of Sodium Barbital on the Physico‐chemical Properties of Surfactants with Different Charges

The effects of sodium barbital (SB) on the solubility of different kinds of surfactants viz., CTAB (cationic head group), SDS (anionic head group) and Triton X‐100 (non ionic head group) in solution phase as well as their first and second critical micelle concentrations (CMC1 and CMC2), the change in Kraft temperatures (T_K) and cloud points (CP) have been studied. Furthermore, the article reports SB‐surfactant interaction study, which is application oriented and highlights the underlying physico‐chemical aspects of the system through florescence and conductivity measurements. The results show that the solubility of CTAB and Triton X‐100 increases with the addition of SB, and that of SDS increases in the presence of small amounts of SB and decreases in the presence of large amounts of SB. With the increasing SB concentration, the CMC of CTAB and CMC1 of Triton X‐100 both increase, while the CMC of SDS decreases, and the CMC2 of Triton X‐100 has no obvious change. The addition of SB decreases the T_K of CTAB sharply, but it increases the T_K of SDS and the CP of Triton X‐100. The different effects of SB on the physico‐chemical properties of differently charged surfactants may be related to its different interactions with the surfactants.     

Influence of surfactants on the adsorption and elektrokinetic properties of the system: guar gum/manganese dioxide

The adsorption of non-ionic polysaccharide—guar gum (GG) in the presence or absence of the surfactants: anionic SDS, cationic CTAB, nonionic TX-100 and their equimolar mixtures SDS/TX-100, CTAB/TX-100 from the electrolyte solutions (NaCl, CaCl₂) on the manganese dioxide surface (MnO₂) was studied. The increase of GG adsorption amount in the presence of surfactants was observed in every measured system. This increase results from formation of complexes between the GG and the surfactant molecules. This observation was confirmed by the determination of the influence of GG on surfactants adsorption on the MnO₂ surface. The increase of GG adsorption on MnO₂ was the largest in the presence of the surfactant mixtures (CTAB/TX-100; SDS/TX-100) which is the evidence of the synergetic effect. The smallest amounts of adsorption were obtained in the presence of TX-100, which results from non-ionic character of this surface active agent. In the case of single surfactant solution CTAB has the best efficiency in increasing the amount of GG adsorption on MnO₂ which results from strong interactions with GG and also with the negatively charged surface of the adsorbent. In order to determine the electrokinetic properties of the system, the surface charge density of MnO₂ and the zeta potential measurements were performed in the presence of the GG macromolecules and the above mentioned surfactants and their mixtures. The obtained data showed that the adsorption of GG or GG/surfactants complexes on the manganese dioxide surface strongly influences the diffused part of the electrical double layer (EDL)—MnO₂/electrolyte solution, but has no influence on the compact part of the electric double layer. This is the evidence that the polymers chains are directly bonded with the surface of the solid and the surfactants molecules are present in the upper part of the EDL.     

FLUORESCENCE PROBE STUDIES ON THE SECOND CRITICAL MICELLE CONCENTRATION OF SEVERAL KINDS OF SURFACTANTS

The fluorescence intenstiy ratios (F₂/F₁) of excimer (F₂) to monomer (F₁) of probe (pyrene) were measured as a function of the concentration of the surfactant in several systems, which consist of sodium hexadecyl sulfonate (C₁₆As)-anionic surfactant, cetyltrimethylammonium bromide (CTAB)-cationic surfactant and pentaoxyethylene decyl ether (C₁₀E₅)-nonionic surfactant. The second CMC values were obtained according to F₂/F₁ ~ surfactant concentration curve break. In addition, we also studied the variation of second CMC vs NaCl concentration. It was found that the second CMC values of C₁₆A₅ and CTAB decreased with the increase of NaCl concentration. But the present of NaCl had no influence on the second CMC value of C₁₀E₅. Results showed that sphere-shaped micelles turn into rod-like micelle at the second CMC. The results were interpreted in terms of diffusion of pyrene molecules and the distribution of pyrene among micelles.     

Foaming in aqueous solutions of zwitterionic surfactant: Effects of oil and salts

This paper reports a study on the stability of foams generated from the aqueous solutions of the zwitterionic surfactant, N-Dodecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate, in presence of NaCl, CaCl₂ and AlCl₃. The effect of oil (i.e. n-hexane) on foam was also studied. The surface and interfacial tensions were measured. These tensions and the CMC decreased upon salt addition, signifying an increased adsorption of the surfactant molecules at the interface. The quantity of salt required for reducing the surface tension and CMC was in the sequence: NaCl > CaCl₂ > AlCl₃. The salts had a pronounced effect on the foaming characteristics, i.e. they reduced the initial foam volume. The effectiveness of salts in reducing the foam stability followed the sequence: AlCl₃ > CaCl₂ > NaCl. However, the foam collapse rate was reduced in the presence of salt. The presence of oil decreased the foam volume and reduced its stability. The entering, bridging, and spreading coefficients were calculated, which explained the stability of foams in presence of oil.     

Polymethylmethacrylate derivatives Eudragit E100 and L100: Interactions and complexation with surfactants

Precipitation or coprecipitation of polyelectrolytes has been largely investigated. However, the precipitation of polyelectrolytes via addition of charged and non‐charged surfactants has not been systematically studied and reported. Consequently, the aim of this work is to investigate the effect of different surfactants (anionic, cationic, non‐charged and zwitterionic) on the precipitation of cationic and anionic polymethylmethacrylate polymers (Eudragit). The surfactants effect has been investigated as a function of their concentration. Special attention has been dedicated to the CMC range and to the colloidal characterization of the formed dispersions. Moreover, the effect of salt (NaCl) and pH was also addressed. It is pointed out that non‐ionic and zwitterionic surfactants do not interact with charged Eudragit E100 and L100. For oppositely charged Eudragit E100/SDS and Eudragit L100/CTAB, precipitation occurs, and the obtained dispersions have been characterized in terms of particle size distribution and zeta potential. It was established that the binding of SDS molecules to Eudragit E100 polymer chains is made through the negative charges of the surfactant heads under the CMC value whereas binding of CTAB to Eudragit L100 chains is made at a CTAB concentration 5 times above its CMC. For Eudragit E100/SDS system, a more acidic medium induces aggregation. A same result was observed for the Eudragit L100/CTAB at a more basic pH. Moreover, it was observed that increasing salt concentration (higher than 100 mM) led to aggregation as generally observed for polycations/anionic surfactant systems.     

Selective wetting of heterogeneous surfaces by solutions of surfactants

Selective wetting of dimethyldichlorosilane-modified glass plates by solutions of tetradecyltrimethylammonium bromide (TDTAB), a cationic surfactant, in p-xylene has been studied. When surfactant concentrations are lower than the critical micelle concentration (CMC), the contact angles under selective wetting conditions increase with increasing hydrophobic surface fraction. When surfactant concentrations are higher than CMC, contact angles are the same on all substrates studied. The adsorption of the surfactant on hydrophilic and hydrophobic regions of heterogeneous surfaces and the stability of wetting films are taken into account in interpreting the results.     

The contact angles of surfactant solution on the quartz surface

Summary The contact angles formed on the quartz surface by 0,1 N NaCl aqueous solution at different pH were measured. The effect of surfactants such as anion-active sodium dodecyl sulphate (NaDS) and cation-active cetyltrimethylammonium bromide (CTAB) was investigated. The results are interpreted in terms of the Frumkin-Derjaguin theory of wetting.With 4 figures and 1 table     

Wettability of a Polymethylmethacrylate Surface by Extended Anionic Surfactants: Effect of Branched Chains

The adsorption behaviors of extended anionic surfactants linear sodium dodecyl(polyoxyisopropene)₄ sulfate (L-C₁₂PO₄S), branched sodium dodecyl(polyoxyisopropene)₄ sulfate (G-C₁₂PO₄S), and branched sodium hexadecyl(polyoxyisopropene)₄ sulfate (G-C₁₆PO₄S) on polymethylmethacrylate (PMMA) surface have been studied. The effect of branched alkyl chain on the wettability of the PMMA surface has been explored. To obtain the adsorption parameters such as the adhesional tension and PMMA-solution interfacial tension, the surface tension and contact angles were measured. The experimental results demonstrate that the special properties of polyoxypropene (PO) groups improve the polar interactions and allow the extended surfactant molecules to gradually adsorb on the PMMA surface by polar heads. Therefore, the hydrophobic chains will point to water and the solid surface is modified to be hydrophobic. Besides, the adsorption amounts of the three extended anionic surfactants at the PMMA–liquid interface are all about 1/3 of those at the air–liquid interface before the critical micelle concentration (CMC). However, these extended surfactants will transform their original adsorption behavior after CMC. The surfactant molecules will interact with the PMMA surface with the hydrophilic heads towards water and are prone to form aggregations at the PMMA–liquid interface. Therefore, the PMMA surface will be more hydrophilic after CMC. In the three surfactants, the branched G-C₁₆PO₄S with two long alkyl chains exhibits the strongest hydrophobic modification capacity. The linear L-C₁₂PO₄S is more likely to densely adsorb at the PMMA–liquid interface than the branched surfactants, thus L-C₁₂PO₄S possesses the strongest hydrophilic modification ability and shows smaller contact angles on PMMA surface at high concentrations.     

Molecular dynamics study of salt effects on micellization of N-dodecyl-N,N-dimethyl-3-ammonio-1-propane-sulfonate

In this paper, molecular dynamics simulation methods were used to investigate salt effects on micellization of N-Dodecyl-N,N-Dimethyl-3-Ammonio-1-Propane-sulfonate (SB12-3) in aqueous solution. It is proved that micelle shapes transform from spherical to prolate spherical shape after 30.0?ns simulation with different NaCl and CaCl₂ concentration. By comparison with the eccentricity value without salt addition, SB12-3 shows salt tolerance behaviors due to its unique “inner salt” structure of amphiphilic surfactant. Radial distribution function (RDF), hydrophobic groups solvent accessible surface area (SASA), hydrogen bond, and the deuterium order parameter (S_CD) are to elucidate salt effects on SB12-3 micelle formation. The radius of micelle is achieved by the related RDF value and in accordance with other researches. The addition of NaCl and CaCl₂ didn’t change the structure of micelle significantly and have little effects on the interactions between SB12-3 and water molecule. By comparison with the results without salt system, SASA of hydrophobic groups is almost the same, and SASA of hydrophilic groups and total molecule fluctuates only slightly. This further indicates that the surface of micelles is more hydrophilic due to the strong interactions between SB12-3 and water molecules. The existence of NaCl and CaCl₂ will enhance the hydrophilic interactions.     

Capillary Flow of Cationic Polyelectrolyte Solutions

The flow rates and the dynamic contact angles of aqueous solutions of cationic polyelectrolyte (CPE) in quartz capillaries with radius of 3–4 m are measured. It is shown that the surface tension and viscosity of CPE solutions with concentrations from 10^–1 to 10^–5 g/l are the same as for water. Surface inactivity of CPE leads to the substantial difference between the capillary properties of their solutions and those of surfactant solutions. It is established that, as the solution concentration increases, the advancing contact angles are reduced from 83° to 75°; the receding contact angles lie between 10° and 20°. Large hysteresis of contact angle can probably be related to the formation of metastable wetting film behind the receding meniscus. Surface hydrophobization occurs as a result of the adsorption of CPE molecules on the negatively charged quartz surface. The specific features of the application of CPE solutions in the deposition technology of hydrophobic coatings, the capillary imbibition and displacement of oils from hydrophobic pores are discussed.     

Hydrophobic and electrostatic interactions in the mixture hydrolyzed polyacrylamide–N-dodecylpyridinium chloride (AD37–DPC) in aqueous solution

The interactions of oppositely charged polyelectrolyte and surfactant (anionic polyacrylamide AD37 and dodecylpyridinium chloride DPC, respectively) in aqueous solution were studied at 25 °C by measurement of viscosity and conductivity. The system was investigated in aqueous medium in the absence and presence of NaCl. The AD37 interacts strongly with the DPC surfactant of the opposite charge. The interactions are electrostatic and hydrophobic. Thus, they are manifested in the formation of hydrophobic aggregates. The critical aggregation concentration (CAC) is much lower than the critical micellar concentration (CMC) of the surfactant alone. However, the value of the saturation concentration X ₂ is higher. The ionic strength of the medium after addition of salt explains an important part of these interactions. In fact, the electrolyte charge affects the CMC and the CAC values.     

Competitive adsorption in the system: carboxymethylcellulose/surfactant/electrolyte/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

The adsorption of carboxymethylcellulose (CMC) in the presence or absence of the surfactants: anionic SDS, nonionic Triton X-100 and their mixture SDS/TX-100 from the electrolyte solutions (NaCl, CaCl₂) on the alumina surface (Al₂O₃) was studied. In each measured system the increase of CMC adsorption in the presence of surfactants was observed. This increase was the smallest in the presence of SDS, a bit larger in the presence of Triton X-100 and the largest when the mixture of SDS/Triton X-100 was used. These results are a consequence of formation of complexes between the CMC and the surfactant particles. Moreover, the dependence between the amount of surfactants’ adsorption and the CMC initial concentration was measured. It comes out that the surfactants’ adsorption amount is not dependent on the CMC initial concentration and moreover, it is unchanged in the whole measured concentration range. The influence of kind of electrolyte, its ionic strength as well as pH of a solution on the amount of the CMC adsorption at alumina surface was also measured. The amount of CMC adsorption is larger in the presence of NaCl than in the presence of CaCl₂ as the background electrolyte. It is a result of the complexation reaction between Ca²⁺ ions and the functional groups of CMC belonging to the same macromolecule. As far as the electrolyte ionic strength is concerned the increase of CMC adsorption amount accompanying the increase of electrolyte ionic strength is observed. The reason for that is the ability of electrolyte cations to screen every electrostatic repulsion in the adsorption system. Another observation is that the increase of pH caused the decrease of CMC adsorption. The explanation of this phenomenon is connected with the influence of pH on both dissociation degree of polyelectrolyte and kind and concentration of surface active groups of the adsorbent.     

Wetting characteristics of aqueous rhamnolipids solutions

The wetting properties of surfactants on solid surfaces form the basis of many industrial and biological processes. The preferential adsorption of the surfactants from aqueous solutions onto solid surfaces alter the adhesion tension of the surface and this behavior may cause partial to complete wetting of the surfaces by the aqueous surfactant solutions. However, different types of surfactants show different wetting characteristics. To study the wetting properties of biologically produced rhamnolipids (RL), advancing contact angles of the aqueous solutions of the RL mixture of R1 and R2 in a ratio of R2/R1=1.1 were measured as a function of surfactant concentration. For a comparison of the wetting performance, sodium dodecyl sulfate (SDS) was chosen as the reference surfactant. A hydrophilic glass surface, a hydrophobic polymer, polyethylene terephthalate (PET), and gold surface were used as the solid surfaces to determine the wetting characteristics of rhamnolipids. At low surfactant concentrations (RL concentration <3x10(-5)M, SDS concentration<3x10(-4)M) contact angle (Theta) varied in a certain range depending on the character of the surfactant interactions with the surface. This was followed by a decrease in contact angle. Parallel to this behavior, at low surfactant concentrations the adhesion tension decreased, then remained constant and an increase at higher surfactant concentrations was obtained on hydrophobic surfaces. On hydrophilic surfaces a steady decrease in adhesion tension was observed with both surfactant solutions.     

Influence of ionic composition in aqueous solution on wettability of rock surface-experiment and economics evaluation

In this study, the influence of different ionic composition in aqueous solution on the minerals surface wettability was studied. The differences effect of monovalent ion and divalent ions onto the wettability alteration were studied. The anions were Cl^- and SO₄^2-. The SO₄^2- could make the minerals surface more hydrophilic. Besides, the influence of NaCl, MgCl₂, CaCl₂, Na₂SO₄, K₂SO₄ and MgSO₄ on the mineral wettability alteration were studied. The results indicated that divalent ions showed significant impact on the minerals wettability alteration, compared with monovalent ion. The reasons were due to the fact that divalent ions showed higher ions adsorption than monovalent ion, and divalent ions have higher effect on compressing the electric double layer. The static contact angle and dynamic contact angle were measured. Different heavy oils were studied, including heavy oil with 100 ppm, heavy oil, heavy oil without resins, heavy oil without asphaltenes. The results showed that the asphaltenes would make it difficult for the heavy oils to liberate from minerals, thus decreasing the oil drops contact angle. Then the resins would decrease the heavy oil contact angles. CaCl₂/MgCl₂ and K₂SO₄ have synergistic effect on the change of the minerals surface wettability. Atomic force microscope (AFM) measurement indicated that the ions would effectively decrease the interaction force on the surface of heavy oil-minerals, which was beneficial to the heavy oil liberation. The roughness measurement indicated that the different ions would effectively increase the minerals surface wettability.     

The Kinetics of Dewetting of Hydrophobic Surfaces during the Evaporation of Surfactant Solution Drops

The kinetics of dewetting (a decrease in contact angles and wetted surface area) during the evaporation of drops of cetyltrimethylammonium bromide (CTAB) solutions from paraffin and Teflon surfaces was studied in a wide concentration range. Three different stages of this process were found: (1) a monotonic decrease in the contact angle at a fixed position of the three-phase contact line, (2) contraction of the wetted surface area (the drop base) at a constant contact angle, and (3) simultaneous contraction of the drop base and a decrease in the contact angle. The CTAB distribution over a solid surface after the drop evaporation was studied by autoradiography. Depending on the surfactant concentration and the nature of a hydrophobic substrate, dewetting occurs by two mechanisms: slipping and carpet rolling.