Biosorption of mercury by carboxymethylcellulose and immobilized Phanerochaete chrysosporium

Phanerochaete chrysosporium basidiospores immobilized onto carboxymethylcellulose were used for the removal of mercury ions from aqueous solutions. The biosorption of Hg(II) ions onto carboxymethylcellulose and both immobilized live and heat-inactivated fungal mycelia of Phanerochaete chrysosporium was studied using aqueous solutions in the concentration range 30-700 mg l⁻¹. The biosorption of Hg(II) ions by the carboxymethylcellulose and both live and heat-inactivated immobilized preparations increased as the initial concentration of mercury ions increased in the medium. Maximum biosorption capacity for immobilized live and heat-inactivated fungal mycelia of Phanerochaete chrysosporium was found to be 83.10 and 102.15 mg Hg(II) g⁻¹, respectively, whereas the amount of Hg(II) ions adsorbed onto the plain carboxymethylcellulose beads was 39.42 mg g⁻¹. Biosorption equilibria were established in approximately 1 h and the correlation regression coefficients show that the adsorption process can be well defined by a Langmuir equation. Temperature changes between 15 and 45 °C did not affect the biosorption capacity. The effect of pH was also investigated and the maximum adsorption of Hg(II) ions onto the carboxymethylcellulose and both live and heat-inactivated immobilized fungal mycelia was observed at pH 6.0. The carboxymethylcellulose-fungus beads could be regenerated using 10 mM HCl, with up to 95% recovery. The biosorbents were used in three biosorption-desorption cycles and no significant loss in the biosorption capacity was observed.     

Design and evaluation of functionalized multi-walled carbon nanotubes by 3-aminopyrazole for the removal of Hg(II) and As(III) ions from aqueous solution

Carboxylated multi-walled carbon nanotubes (MWCNTs-COOH) were chemically modified with 3-aminopyrazole (MWCNTs-f) and applied as an efficient adsorbent to mercury and arsenic adsorption from aqueous solutions. The adsorbents were characterized by FT-IR, EDX, FE-SEM, TGA, and BET. The effects of pH, adsorbent dose, and initial ions concentration on the adsorption efficiency and the optimum conditions were investigated by central composite design. The optimum conditions were obtained at pH 7.6–7.9, adsorbent dose 20 mg, and initial ions concentration 20 ppm. So the maximum adsorption efficiencies in these conditions were 80.5 and 72.4% for the removal of Hg(II) and As(III) by MWCNTs-f, respectively. The quadratic model was used for the analysis of variance and indicated that adsorption of metal ions strongly depends on pH. Also, the pseudo-second-order model has been achieved from the adsorption kinetic studies. Furthermore, the experimental data were well fitted to the Langmuir isotherm and the maximum adsorption capacities obtained were 112 and 133 mg g^?1 for the adsorption of Hg(II) and As(III) by MWCNTs-f, respectively. Moreover, a thermodynamic study revealed that the adsorption reactions were spontaneous and endothermic with the increase in randomness. In addition, a desorption study showed the favorable regeneration ability of MWCNTs-f even after three adsorption–desorption cycles. Therefore, the MWCNTs-f adsorbent has good potential for the removal of Hg(II) and As(III) pollutants from aqueous solutions.     

A chelating polymer resin: synthesis,characterization, adsorption and desorption performance for removal of Hg(II) from aqueous solution

A chloromethylated polystyrene-N-methyl thiourea chelating resin (DMTUR) was successfully prepared by the reaction of chloromethylated polystyrene beads (PS-Cl) with N-methyl thiourea (DMTU). The DMTUR exhibited a high selective adsorption toward Hg(II) in the mixture of different metal ions containing Cu(II), Hg(II), Cd(II), Pb(II), Cr(III) and Ni(II), and the adsorption capacity of Hg(II) approached a maximum with a value of 347 mg/g at pH = 4.0. Moreover, the batch kinetic study showed that the adsorption behavior of Hg(II) presented as a pseudo-second-order manner. And the adsorption isotherms fitted well with Langmuir model, and the maximum uptake of Hg(II) could reach to be 476 mg g^?1 at 35 °C. The thermodynamics study ensured the adsorption process essentially as favorable and endothermic. Finally, an eluent of 4 M HNO₃ solution could completely remove the adsorbed Hg(II) and the adsorption capacity allowed a high level at least five cycles. As aforementioned appealing properties, the DMTUR with simple technology, high adsorption capacity, significant selectivity and good regenerability may have a potential application in industrial scale as a treatment of enriched Hg(II) in wastewater.     

Synthesis of thiol chelating resins and their adsorption properties toward heavy metal ions

A series of chelating resins, derived from a macroreticular styrene-divinylbenzene (2%) copolymer beads grafted with various poly(ethylene glycols) HO? (? CH₂? CH₂? O? )_n? H(n = 0, 4, 9, 13) and containing thiol groups as chelating functions, have been synthesized in a three-step reaction sequence. The structure of the functionalized resins was confirmed by IR spectrophotometry, elemental analysis, and differential scanning calorimetry. The complexation behavior of these thiol resins was investigated towards Hg(II), Cu(II), and Pb(II) ions in aqueous solution by a batch equilibration technique. The influence of pH on adsorption capacity was also examined. The adsorption values for metal ions' intake followed the order Hg(II) > Cu(II) > Pb(II). The affinity of these polymers towards Hg(II) ions was so high that the total mercury level in the liquid decreased from 20 ppm to below 10 ppb after 2 h of treatment. Polymers can be regenerated by washing with a solution of hydrochloric acid (6N) and 10% by weight of an aqueous solution of thiourea. © 1994 John Wiley & Sons, Inc.     

Bulk polymer nanoparticles containing a tetrakis(3-hydroxyphenyl)porphyrin for fast and highly selective separation of mercury ions

We report on the synthesis of polymeric nanoparticles (PNPs) containing a tetrakis(3-hydroxyphenyl)porphyrin, and their use for the separation of mercury(II) ion. The PNPs were prepared by bulk polymerization from methacrylic acid (the monomer), ethyleneglycol dimethacrylate (the cross-linker), 2,2′-azobisisobutyronitrile (the radical initiator) and the mercury(II) complex of 5,10,15,20-tetrakis(3-hydroxyphenyl)-porphyrin. The Hg(II) ion was then removed by treatment with dilute hydrochloric acid. The PNPs were characterized by colorimetry, FT-IR spectroscopy, and scanning electron microscopy. The material is capable of binding Hg(II) from analyte samples. Bound Hg(II) ions can be eluted with dilute nitric acid and then quantified by cold vapor AAS. The extraction efficiency, the effects of pH, preconcentration and leaching times, sample volume, and of the nature, concentration and volume of eluent were investigated. The maximum adsorption capacity of the PNPs is 249 mg g^?1, the relative standard deviation of the AAS assay is 2.2 %, and the limit of detection (3σ) is 8 ng.L^?1. The nanoparticles exhibit excellent selectivity for Hg(II) ion over other metal ions and were successfully applied to the selective extraction and determination of Hg(II) ion in spiked water samples.

Solid phase extraction and preconcentration of trace mercury(II) from aqueous solution using magnetic nanoparticles doped with 1,5-diphenylcarbazide

A new method for solid-phase extraction and preconcentration of trace mercury(II) from aqueous solution was developed using 1,5-diphenylcarbazide doped magnetic Fe₃O₄ nanoparticles as extractant. The surface treatment did not result in the phase change of Fe₃O₄. Various factors which influenced the recovery of the analyte were investigated using model solutions and batch equilibrium technique. The maximum adsorption occurred at pH?>?6, and equilibrium was achieved within 5 min. Without filtration or centrifugation, these mercury loaded nanoparticles could be separated easily from the aqueous solution by simply applying an external magnetic field. At optimal conditions, the maximum adsorption capacity was 220 μmol g^?1. The mercury ions can be eluted from the composite magnetic particles using 0.5 mol L^?1 HNO₃ as a desorption reagent. The detection limit of the method (3σ) was 0.16 μg L^?1 for cold vapor atomic absorption spectrometry, and the relative standard deviation was 2.2%. The method was validated by the analysis of a certified reference material with the results being in agreement with those quoted by manufactures. The method was applied to the preconcentration and determination of trace inorganic mercury(II) in natural water and plant samples with satisfactory results.     

Preparation of poly(hydroxyethyl methacrylate-co-methacrylamidohistidine) beads and its design as a affinity adsorbent for Cu(II) removal from aqueous solutions

Different metal-complexing ligands carrying synthetic adsorbents have been reported in the literature for heavy metal removal. We have developed a novel and new approach to obtain high metal adsorption capacity utilizing 2-methacrylamidohistidine (MAH) as a metal-complexing ligand. MAH was synthesized by using methacrylochloride and histidine. Spherical beads with an average size of 150–200 μm were obtained by the radical suspension polymerization of MAH and 2-hydroxyethylmethacrylate (HEMA) conducted in an aqueous dispersion medium. Owing to the reasonably rough character of the bead surface, p(HEMA-co-MAH) beads had a specific surface area of 17.6 m² g⁻¹. Synthesized MAH monomer was characterized by NMR. p(HEMA-co-MAH) beads were characterized by swelling studies, FTIR and elemental analysis. These p(HEMA-co-MAH) affinity beads with a swelling ratio of 65%, and containing 1.6 mmol MAH g⁻¹ were used in the adsorption/desorption of copper(II) ions from metal solutions. Adsorption equilibria was achieved in ∼2 h. The maximum adsorption of Cu(II) ions onto pHEMA was ∼0.36 mg Cu(II) g⁻¹. The MAH incorporation significantly increased the Cu(II) adsorption capacity by chelate formation of Cu(II) ions with MAH molecules (122.7 mg Cu(II) g⁻¹), which was observed at pH 7.0. pH significantly affected the adsorption capacity of MAH incorporated beads. The observed adsorption order under non-competitive conditions was Cu(II)>Cr(III)>Hg(II)>Pb(II)>Cd(II) in molar basis. The chelating beads can be easily regenerated by 0.1 M HNO₃ with higher effectiveness. These features make p(HEMA-co-MAH) beads very good candidate for Cu(II) removal at high adsorption capacity.     

A Novel Hg(II) PVC Membrane Sensor Based on Simple Ionophore Ethylenediamine Bis‐Thiophenecarboxaldehyde

Abstract

A mercury (II) ion‐selective polyvinyl chloride (PVC) membrane sensor based on ethylenediamine bisthiophenecarboxaldehyde (EDBT) as a novel nitrogen‐ and sulfur‐containing sensing material was successfully developed. The ionophore was produced through Schiff's base formation between ethylenediamine and 2‐thiophenecarboxaldehyde. These two reagents have the advantages of low cost and simple chemical compounds. Ortho‐nitro phenyl pentyl ether (o‐NPPE) as solvent and sodium tetraphenyl borate (NaTPB) as a lipophilic salt were chosen. The sensor exhibited a good linear response of 30.0±0.4 mV per decade within the concentration range of 10^?7–10^?2 and a detection limit of 7.0×10^?8 mol L^?1 Hg(II). The sensor showed good selectivity and fast response for the mercury (II) ion with respect to some alkali, alkaline earth, transition, and heavy metal ions. The EDBT–based sensor was suitable for aqueous solutions of pH range from 2.0 to 4.5. It can be used for about 3 months without any considerable divergence in potential. The formation constant of ionophore complex with Hg(II) ion was calculated by using the segmented sandwich membrane method. The structure of both the ionophore and its Hg(II) complex were examined using infrared spectra and elemental analysis. The proposed sensor was applied for the determination of Hg(II) content in some dental amulgum alloys and as an indicator electrode for potentiometric titration of Hg(II) ion with EDTA solution, as well as with I^?, OH^?, and IO₃ ^? ions. In addition, the solubility products of the previous ions were determined by using this sensor.     

Removal of Toxic As (V) Ions by Adsorption onto Alginate and Carboxymethyl Cellulose Beads

The removal of arsenic ions from dilute aqueous solutions using biopolymeric beads of crosslinked sodium alginate and carboxymethyl cellulose (CMC) as the adsorbent is reported in this paper. The biopolymeric alginate and carboxymethyl cellulose beads were prepared and characterized by FTIR spectra. On the surfaces of the prepared beads were performed static and dynamic adsorption studies of arsenic ions at fixed pH and ionic strength of the aqueous metal ion solutions. The adsorption data were applied to Langmuir and Freundlich isotherm equations and various static parameters were calculated. The dynamic nature of adsorption was quantified in terms of several kinetic constants such as rate constant for adsorption (k₁) and Lagergreen rate constant (K_ad). The influence of various experimental parameters such as solid to liquid ratio, pH, temperature, presence of salts and chemical composition of biopolymeric beads were investigated on the adsorption of arsenic ions.     

Nano-iron oxide-encapsulated chitosan microspheres as novel adsorbent for removal of Ni (II) ions from aqueous solution

The present study investigates the utility of composite beads of nano-particles of iron oxide and chitosan for removing Ni (II) ions from aqueous solution by batch and column adsorption techniques. In the batch mode experiment, the influence of pH, concentration, adsorbent dose, temperature, column mode, bed height, flow rate and initial concentration were studied on the adsorption profiles of nickel ions. The maximum uptake of Ni (II) ions was obtained at pH 4.0 in 30 min at room temperature.     

Adsorption of Cu(II) and Zn(II) ions from aqueous solutions onto fine powder of Typha latifolia L. root: kinetics and isotherm studies

Fine powder of Typha latifolia L. root was used for adsorption of copper and zinc ions from buffered and nonbuffered aqueous solutions. The adsorption reached equilibrium in 60 min. During this time, more than 90 % of the adsorption process was completed. The effect of initial pH, initial concentration of metal ion, and contact time was investigated in a batch system at room temperature. The optimum adsorption performance was observed at pH 5.00 and 4.25 for nonbuffered solutions of Cu(II) and Zn(II), respectively, while for buffered solutions it occurred at pH 6.00. The total metal uptake decreased on application of ammonium acetate buffer, from 37.35 to 17.00 mg g^?1 and 28.80 to 9.90 mg g^?1 for Cu(II) and Zn(II) solutions, respectively, with 100 mg L^?1 initial concentration. The pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich models were used to describe the adsorption kinetics. The experimental data followed the pseudo-second-order kinetic model. The biosorption equilibrium was well described by Langmuir and Freundlich isotherm models.     

Adsorption of U(VI) from aqueous solution by sulfonated ordered mesoporous carbon

The sulfonated mesoporous carbon (CMK-3-SO₃H) prepared by functionalizing mesoporous carbon (CMK-3) via vapor transfer method has been explored for the removal and recovery of uranium from aqueous solutions. The influences of different experimental parameters such as solution pH, initial concentration, contact time and temperature on adsorption were investigated. The results showed that CMK-3-SO₃H has the highest uranium sorption capacity at initial pH of 5.0 and contact time of 120 min, and the adsorption process could be better described by the pseudo-second-order model and Langmuir isotherm. Selective adsorption studies showed that the CMK-3-SO₃H could selectively remove of U(VI), and the selectivity coefficients of mesoporous carbon in the presence of co-existing ions, Mg(II), Zn(II), Mn(II), Cu(II), Ni(II), Sr(II) and Hg(II) improved after functionalization.     

Conductimétrie des complexes cyanés du mercure (ii) application aux dosages

The formation of complex cyanides of mercury (II) has been studied by conductimetry. The shape of the conductimetric curves at different dilutions and different pH levels may be explained by the initial presence of HgOH⁺ ions and of colloidal hydroxide Hg(OH)₂ then by the successive formation of Hg(CN)₂, HCN and Hg(CN)₄^-2.These hypotheses have been verified by measurements of pH and of oxidation-reduction potential.The dissociation constants of the complexes Hg(CN)₂ and Hg(CN)₄^-2 have been calculated and are 10^-21.7 and 10^-27.7 respectively.A simple conductimetric method has been evolved which allows simultaneous determination of the amounts of mercury (II) and the free acid in a solution. The piesence of Cl^-ions is recommended to increase the precision of the determination.     

Comparative Adsorption of Lead(II) on Flake and Bead‐Types of Chitosan

The adsorption of Pb(II) ions from aqueous solutions by chitosan flakes and beads was studied. The chitosan beads were prepared by casting an acidic chitosan solution into alkaline solution. Experiments were carried out as a function of pH, agitation period and initial concentration of Pb²⁺ ions. The uptake of Pb²⁺ ions from aqueous solution was determined from changes in concentration as measured by atomic absorption spectroscopy. The maximum uptake of Pb²⁺ ions on chitosan beads was greater than that on chitosan flakes. Adsorption isothermal data could be interpreted by the Langmuir equation. The experimental data of the adsorption equilibrium from Pb²⁺ ion solutions correlated well with the Langmuir isotherm equation. SEM analyses were also conducted for visual examination of the chitosan flakes and beads. Physical properties including surface area and average pore diameter were characterized by N₂ adsorption experiment.     

Equilibrium and kinetics studies on adsorption of Cu(II) from aqueous solutions onto a graft copolymer of cross-linked starch/acrylonitrile (CLSAGCP)

A synthetic graft copolymer of cross-linked starch/acrylonitrile was used as an adsorbent for the removal of Cu(II) ions from an aqueous solution of copper nitrate hexahydrate Cu(NO₃)₂ · 6H₂O at different temperatures and fixed pH. The amount adsorbed increased with increasing concentration of Cu(II) ions and decreasing temperature. The length of time taken to reach equilibrium of the adsorption of Cu(II) ions was the same at all temperatures tested. Kinetics studies showed that the adsorption process obeyed first-order reversible kinetics and the adsorption isotherms followed the Freundlich model. Furthermore, the thermodynamic parameters, i.e. standard free energy (ΔG^∘), standard enthalpy (ΔH^∘), and standard entropy (ΔS^∘), of the adsorption process were calculated and the results are discussed in detail.     

The adsorption of U(VI) and Hg(II) on Paecilomyces catenlannulatus proteases

The adsorption of U(VI) on Paecilomyces catenlannulatus as a function of agitation time, pH and solution concentration was investigated by batch techniques. Hg(II) cation was also employed to compare the adsorption capacity of P. catenlannulatus in this study. The adsorption kinetics indicate that the adsorption of U(VI) and Hg(II) on P. catenlannulatus can be fitted by pseudo-second kinetic model very well. The optimum pH for U(VI) removal was 7.0, whereas the high level of adsorption of Hg(II) was observed at pH >7.0 due to the occurrence of precipitate (i.e., Hg(OH)₂(s)). The maximum adsorption capacity of P. catenlannulatus calculated from Langmuir model was 163.93 and 140.85 mg g^?1 for U(VI) and Hg(II), respectively. This paper highlights the application of P. catenlannulatus as suitable bio-materials for the preconcentration and removal of radionuclides from aqueous solutions in environmental pollution management.     

Silver modified magnetic carbon nanotubes composite as a selective solid phase extractor for preconcentration and determination of trace mercury ions in water solution

A magnetic composite of silver/iron oxides/carbon nanotubes (Ag/Fe₃O₄/CNTs) was synthesized and used as an adsorbent for the preconcentration of mercury ions in water solutions at room temperature (25°C) in this study. The silver nanoparticles were supported on the magnetic CNTs. The modification enabled the composite had not only a high adsorption capacity for mercury ions (Hg²⁺) but also the magnetic isolation properties. A fast, sensitive, and simple method was successfully developed for the preconcentration and determination of trace amount of Hg²⁺ in water using the synthesized nanocomposite as adsorbent. The mercury concentration was determined by an atomic fluorescence spectrometer (AFS). The experimental conditions such as pH value, extraction temperature, extraction time, sample volume, eluent composition and concentration, sorbent amount, and coexisting ions were investigated for the optimization. A 500 mL of sample volume resulted in a preconcentration factor of 125. When a 200 mL of sample was employed, the limit of detection for Hg²⁺ was as low as 0.03 ng mL^?1with relative standard deviation of 4.4% at 0.1 ng mL^?1 (n = 7). The ease of synthesis and separation, the good adsorption capacity, and the satisfactory recovery will possibly make the composite an attractive adsorbent for the preconcentration of ultratrace Hg²⁺ in waters.     

Naked magnetite nanoparticles for both clean-up and solid-phase extraction-trace determination of mercury

A new solid-phase extraction method was developed for trace determination of Hg(II) by using a small amount of naked magnetite nanoparticles as an adsorbent. The magnetite nanoparticles were characterized by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The adsorbed Hg(II)-dithizone complex was eluted with 1.0 mL aliquot of an acidic 1-propanol solution prior to electrothermal atomic absorption spectrometry. A huge positive effect was found on the mercury adsorption by ionic strength. Under optimized condition, a linear calibration curve was obtained for mercury in the range of 0.2–50 ng mL^?1 with relative standard deviation in the range of 0.5–2.0%. The limit of detection and enrichment factor were 0.01 ng mL^?1 and 98.3, respectively. The effects of coexisting ions were studied extensively, and a new clean-up procedure was used to remove the matrix effects by using a simple sample pretreatment step using a little amount of magnetite nanoparticles. The method was successfully applied to the determination of Hg(II) in different water and human urine samples and a commercial sodium nitrate.     

Biosorption of Co(II), Cr(III), Cd(II), and Pb(II) Ions from Aqueous Solution Using Nonliving Neochloris Pseudoalveolaris Deason & Bold: Equilibrium,Thermodynamic, and Kinetic Study

In this study, biosorption of cobalt(II), chromium(III), cadmium(II), and lead(II) ions from aqueous solution was studied using the algae nonliving biomass (Neochloris pseudoalveolaris, Np) as natural and biological sorbents. The effect of pH, contact time, temperature, and metal concentration on the adsorption capacity of metal ions was investigated. The maximum adsorption capacities for Co(II), Cr(II), Cd(II), and Pb(II) were found to be 20.1, 9.73, 51.4 and 96.2 mg/g at the optimum conditions, respectively. The experiments showed that when pH increased, an increase in the adsorption capacity of the biomass was observed too. The kinetic results of adsorption obeyed a pseudo second-order model. Freundlich and Langmuir isotherm models were applied to experimental equilibrium data of metal ions adsorption and the value of R _L for Pb(II), Cb,(II), Co(II), and Cr(III) was found to be 0.376, 0271, 0872, and 096, respectively. The thermodynamic parameters related to the adsorption process such as E _a , ΔG ⁰, ΔH ⁰, and ΔS ⁰ were calculated. ΔH ⁰ values (positive) showed that the adsorption mechanism was endothermic. Weber-Morris and Urano-Tachikawa diffusion models were also applied to experimental equilibrium data. The algae biomass was effectively used as a sorbent for the removal of metal ions from aqueous solutions.     

Removal of cadmium(II) and lead(II) ions from model aqueous solutions using sol–gel-derived inorganic oxide adsorbent

A study was conducted concerning the preparation and application of a novel synthetic oxide adsorbent of MgO-SiO₂ type. The material was prepared via a sol–gel route, utilizing magnesium ethoxide and tetraethoxysilane as precursors of magnesium oxide and silica respectively, and ammonia as a catalyst. The powder was comprehensively analyzed with regard to chemical composition (EDS method), crystalline structure, morphology, characteristic functional groups, electrokinetic stability and porous structure parameters (BET and BJH models). The synthesized oxide adsorbent is amorphous, with irregularly shaped particles, a relatively large surface area of 612 m²/g, and negative surface charge over almost the whole pH range. Comprehensive adsorption studies were performed to investigate the adsorption of Cd(II) and Pb(II) ions on the MgO–SiO₂ oxide adsorbent, including evaluation of adsorption kinetics and isotherms, the effect of pH, contact time and mass of adsorbent. It was shown that irrespective of the conditions of the adsorption process, the synthesized MgO–SiO₂ adsorbent exhibits slightly better affinity to lead(II) than to cadmium(II) ions (sorption capacity of 102.02 mg(Pb²⁺)/g and 94.05 mg(Cd²⁺)/g). The optimal time for removal of the analyzed metal ions was 60 min, although adsorption reached equilibrium within 10 min for Pb(II) and within 15 min for Cd(II) ions, which was found to fit well with a type 1 pseudo-second-order kinetic model. Additionally, adsorption efficiency was affected by the pH of the reaction system—better results were obtained for pH ≥7 irrespective of the type of metal ion.