Hydrogel composites of neutral and slightly charged poly (acrylamide) gels with incorporated bentonite. Interaction with salt,linear polyelectrolytes and ionic surfactants

The swelling behavior in the solutions of sodium chloride, linear polyelectrolytes and ionic surfactants of the composites based on clay mineral bentonite (BENT) embedded in neutral and slightly charged poly(acrylamide) (PAAm) gels is studied. Negatively charged flat clay particles incorporated into polymer gel adsorb oppositely charged surfactant and linear polyelectrolyte and attract the charged chains of cationic polymer matrix. The results of SAXS study manifest the formation of lamella structure of the cationic surfactant adsorbed by the clay plates. The gels loaded with the clay show a strong response to changes in the nature and the composition of the ionic environment.     

Use of surfactants to remove water-based inks from plastic film: effect of calcium ion concentration and length of surfactant hydrophobe

Effective plastic film deinking could permit the reuse of recycled polymer to produce clear film, reduce solid waste for landfills, reduce raw material demand for polymer production, and aid process economics. In this study, the deinking of a commercial polyethylene film printed with water-based ink was studied using surfactants in the presence of hardness ions (calcium ions) at various pH levels. The electrostatic properties of ink particles in a washing bath were also investigated. Synthetic anionic surfactant or fatty acid soap in the presence of calcium ions at alkaline pH levels was found to be nearly as effective at deinking as cationic, nonionic, or amphoteric surfactants alone. However, adding calcium ions decreases the deinking effectiveness of cationic, nonionic, and amphoteric surfactants. Increasing the length of the ionic surfactant hydrophobe enhances deinking. Zeta potential measurements showed that water-based ink particles in water reach the point of zero charge (PZC) at a pH of about 3.6, above which ink particles are negatively charged, so cationic surfactant tends to adsorb better on the ink than anionic surfactant above the PZC in the absence of calcium. As the cationic surfactant concentration is varied between 0.005 and 25 mM, the zeta potential of the ink particles reverses from negative to positive owing to adsorption of cationic surfactant. For anionic surfactants, added calcium probably forms a bridge between the negatively charged ink and the negatively charged surfactant head groups, which synergizes adsorption of the surfactant and aids deinking. In contrast, calcium competes for adsorption sites with cationic and nonionic surfactants, which inhibits deinking. All the surfactants studied here disperse ink particles effectively in the washing bath above pH 3 except for the ethoxylated amine surfactant.     

The Interaction between High-Molecular-Weight Flocculents and Ionic Surfactants

The interaction between the anionic and cationic polyelectrolytes of various molecular masses and charges and the ionic surfactants in aqueous and salt solutions is studied by viscometry, conductometry, light scattering, and electrophoresis. Oppositely charged molecules of surfactant and polymer form strong complexes due to the forces of electrostatic attraction that is manifested in a significant decrease in the viscosity and light transmission, as well as in the relative reduction in solution conductivity. As the surfactant/polyelectrolyte ratio increases, the forming complexes precipitated and then dissolved again. In the case of strongly charged polyelectrolytes, the partial dissolution of precipitates was observed preceding the wide region of destabilization. In this region, the value of surfactant/polyelectrolyte charge ratio reaches 3–4. The interaction between the cationic surfactants and anionic polyelectrolyte increases with the lengthening of alkyl radical, thus indicating the presence of cooperative interactions between the surfactant molecules bonded to polymer and the important role of relevant hydrophobic interactions. As a result, the interaction between the high-molecular-weight anionic polyelectrolytes and anionic surfactants containing aromatic core takes place in some cases.     

Nonionic Cellulose Ethers as Potential Drug Delivery Systems for Periodontal Anesthesia

Nonionic cellulose ethers displaying a lower consolute temperature, or cloud-point, close to body temperature were investigated as potential carrier systems for the delivery of local anesthetic agents to the periodontal pocket. The interaction between the polymers, i.e., ethyl(hydroxyethyl)cellulose (EHEC) and hydrophobically modified EHEC (HM-EHEC), and ionic surfactants was determined in the absence and in the presence of the local anesthetic agents lidocaine and prilocaine. The cloud-point and rheology data indicate interactions between the polymer and both anionic and cationic surfactants. More precisely, a number of ionic surfactants were found to result in an increase in cloud-point at higher surfactant concentrations, a surfactant-concentration-dependent thickening, and a temperature-induced gelation upon heating. Upon addition of the local anesthetic agents lidocaine and prilocaine in their uncharged form to EHEC and HM-EHEC, in the absence of surfactants, only minor interaction with the polymer could be inferred. However, these substances were found to affect the polymer-surfactant interaction. In particular, the drug release rate in vitro as well as the stability and temperature-dependent viscosity were followed for an EHEC/SDS system and EHEC/myristoylcholine bromide system upon addition of lidocaine and prilocaine. The data indicate a possibility of formulating a local anesthetic drug delivery system suitable for administration into the periodontal pocket where at least small amounts of active ingredients can be incorporated into the system without severely affecting the gelation behavior. The results found for the cationic myristoylcholine bromide system are particularly interesting for the application in focus here since this surfactant is antibacterial and readily biodegradable. Copyright 2000 Academic Press.     

Polymer/surfactant interactions at the air/water interface

The development of neutron reflectometry has transformed the study and understanding of polymer/surfactant mixtures at the air/water interface. A critical assessment of the results from this technique is made by comparing them with the information available from other techniques used to investigate adsorption at this interface. In the last few years, detailed information about the structure and composition of adsorbed layers has been obtained for a wide range of polymer/surfactant mixtures, including neutral polymers and synthetic and naturally occurring polyelectrolytes, with single surfactants or mixtures of surfactants. The use of neutron reflectometry together with surface tensiometry, has allowed the surface behaviour of these mixtures to be related directly to the bulk phase behaviour. We review the broad range of systems that have been studied, from neutral polymers with ionic surfactants to oppositely charged polyelectrolyte/ionic surfactant mixtures. A particular emphasis is placed upon the rich pattern of adsorption behaviour that is seen in oppositely charged polyelectrolyte/surfactant mixtures, much of which had not been reported previously. The strong surface interactions resulting from the electrostatic attractions in these systems have a very pronounced effect on both the surface tension behaviour and on adsorbed layers consisting of polymer/surfactant complexes, often giving rise to significant surface ordering.     

Study of Cryostructuring of Polymer Systems: 25. The Influence of Surfactants on the Properties and Structure of Gas-Filled (Foamed) Poly(vinyl alcohol) Cryogels

Foamed poly(vinyl alcohol) (PVA) cryogels are studied. Such heterogeneous gel composites are formed as a result of the cryogenic treatment (freezing—storage in a frozen state—thawing) of water— PVA liquid foams in the absence and presence of surfactants. It is shown that the addition of ionic and nonionic surfactants to an aqueous PVA solution and its subsequent foaming result in the formation of liquid foam whose stability is lower than that of the foam prepared from an aqueous PVA solution in the absence of surfactant, i.e., surfactants cause a destabilizing effect on the foams containing PVA. Gas-filled PVA cryogels formed as a result of freezing—thawing of such foams contain large (up to ～180 μm) pores (air bubbles incorporated into the matrix of heterogeneous gel). Mechanical and thermal properties of cryogels depend on the nature and concentration of surfactants, as well as on the regime of cryogenic treatment. The rigidity of foamed PVA cryogels prepared in the presence of sodium dodecyl sulfate and cetyltrimethylammonium bromide ionic surfactants is lower and that in the presence of nonionic decaoxyethylene cetyl ether is higher than for equiconcentrated (by the polymer) foamed PVA cryogel containing no surfactant. Microscopic studies and the analysis of obtained images of cryogel structure demonstrate that the effect of surfactant on the morphology of freezing foam can be different, depending on the type of surfactant added to the initial system. This leads to foam-destabilizing effects such as the collapse, deformation, and coalescence of air bubbles; the failure of gel phase structure near the bubble surface; etc. However, the complete disintegration of the foamed structure is prevented by a very high viscosity of the unfrozen liquid microphase of a macroscopically solid sample and by the cryotropic PVA gelation that fixes the structure of partially destroyed foam.     

Thermosensitive amphiphilic polyphosphazenes and their interaction with ionic surfactants

Temperature-responding physical hydrogels are promising materials as injectable drug delivery carriers which could hold useful bioactive materials inside the polymer networks for further controlled releases. Aimed at desired qualities at body temperature, those gel characteristics need to be adjusted carefully. In this point of view, surfactant is one of the useful molecules to be used by simple formulations without harmful chemical reactions. In this study, thermothickening of amphiphilic nonionic polyphosphazene solution is modified by anionic and cationic surfactants with different alkyl chains and counter-ions. Specified in the thermothickening system, a maximum viscosity (η_max) and a temperature at that point (T_max) are changed independently reflecting unique intermolecular interactions. At low concentration (1–9 mM) of the added surfactant, the η_max is maximized at 3 mM surfactant regardless of the surfactant type while the T_max is increased continuously along with the surfactant concentration. From a kinetic point of view, this 3 mM surfactant at the maximized η_max reflects a polymer-dominating interaction and highly favorable polymer–surfactant interaction with a low selectivity in the surfactant type. However, the magnitude of the maximum viscosity (η_max) is dependent on the surfactant tail, which reflects the lifetime and the strength of the hydrophobic domains of the polymer network affected by the surfactants. Meanwhile, the magnitude of the T_max depended on the surfactant head group, which means the interfacial tension of the polymer solutions changed by the surfactants. At high concentration (10 and 30 mM) of the cationic surfactants added to the polymer solutions with two different viscosities, the cationic surfactants are supposed to interact either with the hydrophobic parts of the aggregated polymer with high viscosity or on the backbone of the less- or non-aggregated polymer with low viscosity.Ionic surfactants change the thermothickening of the amphiphilic nonionic polyphosphazene solution in a unique tail- or head-dependent way. Moreover, the concentration of the added surfactants and the association pattern of the pure polymer solutions are also crucial for the thermothickening phase behaviors. Temperature-responsive polyphosphazenes in this work exhibit unique and controllable interactions with ionic surfactants.     

Effect of surfactants on shear-induced gelation and gel morphology of soft strawberry-like particles

The role of surfactant type in the aggregation and gelation of strawberry-like particles induced by intense shear without any electrolyte addition is investigated. The particles are composed of a rubbery core, partially covered by a plastic shell, and well stabilized by fixed (sulfate) charges in the end group of the polymer chains originating from the initiator. In the absence of any surfactant, after the system passes through a microchannel at a Peclet number equal to 220 and a particle volume fraction equal to 0.15, not only shear-induced gelation but also partial coalescence among the particles occurs. The same shear-induced aggregation/gelation process has been carried out in the presence of an ionic (sulfonate) surfactant or a nonionic (Tween 20) steric surfactant. It is found that for both surfactants shear-induced gelation does occur at low surfactant surface density but the conversion of the primary particles to the clusters constituting the gel decreases as the surfactant surface density increases. When the surfactant surface density increases above certain critical values, shear-induced gelation and eventually even aggregation do not occur any longer. For the sulfonate surfactant, this was explained in the literature by the non-DLVO, short-range repulsive hydration forces generated by the adsorbed surfactant layer. In this work, it is shown that the steric repulsion generated by the adsorbed Tween 20 layer can also protect particles from aggregation under intense shear. Moreover, the nonionic steric surfactant can also protect the strawberry-like particles from coalescence. This implies a decrease in the fractal dimension of the clusters constituting the gel from 2.76 to 2.45, which cannot be achieved using the ionic sulfonate surfactant.     

Polymethylmethacrylate derivatives Eudragit E100 and L100: Interactions and complexation with surfactants

Precipitation or coprecipitation of polyelectrolytes has been largely investigated. However, the precipitation of polyelectrolytes via addition of charged and non‐charged surfactants has not been systematically studied and reported. Consequently, the aim of this work is to investigate the effect of different surfactants (anionic, cationic, non‐charged and zwitterionic) on the precipitation of cationic and anionic polymethylmethacrylate polymers (Eudragit). The surfactants effect has been investigated as a function of their concentration. Special attention has been dedicated to the CMC range and to the colloidal characterization of the formed dispersions. Moreover, the effect of salt (NaCl) and pH was also addressed. It is pointed out that non‐ionic and zwitterionic surfactants do not interact with charged Eudragit E100 and L100. For oppositely charged Eudragit E100/SDS and Eudragit L100/CTAB, precipitation occurs, and the obtained dispersions have been characterized in terms of particle size distribution and zeta potential. It was established that the binding of SDS molecules to Eudragit E100 polymer chains is made through the negative charges of the surfactant heads under the CMC value whereas binding of CTAB to Eudragit L100 chains is made at a CTAB concentration 5 times above its CMC. For Eudragit E100/SDS system, a more acidic medium induces aggregation. A same result was observed for the Eudragit L100/CTAB at a more basic pH. Moreover, it was observed that increasing salt concentration (higher than 100 mM) led to aggregation as generally observed for polycations/anionic surfactant systems.     

Network structure and swelling behavior of poly(acrylamide/crotonic acid) hydrogels in aqueous salt solutions

Hydrogels with various ionic group contents were prepared from acrylamide and crotonic acid (CrA) monomers with 0–12.9 mol % CrA in aqueous solutions by radiation‐induced polymerization and gelation with γ rays from a ⁶⁰Co source. The volume swelling ratio of the poly(acrylamide/crotonic acid) hydrogels was investigated as a function of the pH and ionic strength of the swelling medium and the type of counterion in the swelling medium. The volume swelling ratio increased with an increase in pH and a decrease in the ionic strength. The volume swelling ratio of these hydrogels was evaluated with an equation, based on the Flory–Huggins thermodynamic theory, the James–Guth phantom network theory, and the Donnan theory of swelling of weakly charged ionic gels, that was modified here for the determination of the molecular weight between crosslinks (M_c) and the polymer–solvent interaction parameter (χ). The modified equation described very well the swelling behavior of the charged polymeric network. The same equation also provided the simultaneous measurement of these parameters for the systems investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1656–1664, 2003     

Controlled association in suspensions of charged nanoparticles with a weak polyelectrolyte

The properties of high-pH suspensions of mixtures of silica with low-molecular-weight samples of the water-soluble polymer polyethylenimine (PEI) have been studied. At pH > 10 and low ionic strength, silica nanoparticles are stabilized by a negative surface charge, and PEI has only a very low positive charge. The adsorption of PEI induces a localized positive charge on the segments of polymer closest to the silica surface. The parts of the molecule furthest away from the surface have little charge because of the high pH of the medium. The polymer-covered particle remains negatively charged, imparting some electrostatic stabilization. Suspensions of silica and low-molecular-weight PEI are low-viscosity fluids immediately after mixing, but aggregation occurs leading to the eventual gelation (or sedimentation at lower concentrations) of these mixtures, indicating colloidal instability. The gelation time passes through a minimum with increasing surface coverage. The rate of gelation increases exponentially with molecular weight: for molecular weight > or = 10,000 Da PEI, the instability is so severe that uniform suspensions cannot be produced using simple mixing techniques. The gelation rates increase rapidly with temperature, ionic strength, and reduction in pH. The rate of gelation increases with increasing particle concentration at low surface coverage but decreases at high coverage as a consequence of a small increase in pH. Gels are broken by application of high shear into aggregates that re-gel more rapidly than the original discrete coated particles.     

Complexation of hydrophobically modified polyelectrolytes with surfactants: anionic poly(maleic acid/octyl vinyl ether)/anionic sodium dodecyl sulfate

Interactions of surfactants with hydrophobically modified polyelectrolytes in aqueous solutions are important in several applications such as detergents, cosmetics, foods, and paints. Fundamental questions arise on the mechanisms of complexation of the polyelectrolyte and surfactant that control their behavior. In this work, the complexation was studied by examining interactions in aqueous solutions of a hydrophobically modified polymer, poly(maleic acid/octyl vinyl ether) (PMAOVE), with sodium dodecyl sulfate (SDS) by monitoring viscosity, pyrene solubility, light scattering, and analytical ultracentrifugation. When the anionic surfactant SDS was added to aqueous solutions of the similarly charged polymer PMAOVE, the surfactant was incorporated into the hydrophobic nanodomains of PMAOVE even far below the cmc of the surfactant. On the basis of viscosity, pyrene solubility, and analytical ultracentrifugation data, it is proposed that PMAOVE undergoes structural unfolding and at higher SDS concentrations mixed micelles are formed.     

Understanding surfactant aided aqueous dispersion of multi-walled carbon nanotubes

Dispersions of multi-walled carbon nanotubes (MWNTs) assisted by surfactant adsorption were prepared for a number of ionic and non-ionic surfactants including sodium 4-dodecylbenzenesulfonate (NaDDBS), hexadecyl(trimethyl)azanium bromide (CTAB), sodium dodecane-1-sulfonate (SDS), Pluronic? F68, Pluronic? F127, and Triton? X-100 to examine the effects of nanotube diameter, surfactant concentration, and pH on nanotube dispersability. Nanotube diameter was found to be an important role in surfactant adsorption rendering single-walled carbon nanotube studies as unreliable in predicting MWNT dispersive behavior. Similar to other reports, increasing surfactant concentrations resulted in a solubility plateau. Quantification of nanotube solubility at these plateaus demonstrated that CTAB is the best surfactant for MWNTs at neutral pH conditions. Deviations from neutral pH demonstrated negligible influence on non-ionic surfactant adsorption. In contrast, both cationic and anionic surfactants were found to be poor dispersing aids for highly acidic solutions while, CTAB remained a good surfactant under strongly basic conditions. These pH dependent results were explained in the context of nanotube surface ionization and Debye length variation.     

Interactions between ethyl(hydroxyethyl) cellulose and lysine-based surfactants in aqueous media

In this work, the interaction between ethyl(hydroxyethyl) cellulose (EHEC) and three dimeric lysine-based surfactants of distinct chain length (C₆, C₈ and C₁₀) have been assessed and the system was evaluated in terms of its temperature-dependent gelling capacity. The viscosity profile depends on the specific surfactant, its concentration and temperature. The observed profiles reflected polymer–polymer associations at elevated temperatures and polymer-surfactant interactions, implying the formation of micellar-type associations. The systems induce gelation at higher temperatures. Longer chain-length surfactants induce gelation at lower concentrations due to their stronger tendency to self-assemble. The thermo-responsive gels showed gel strength generally lower than 20 Pa.sⁿ and a fractal dimension of 2.3–2.4, respectively, indicating the formation of soft gels comprising a tight and homogeneous network. The weakest gel was produced in the presence of the C₆ surfactant. 2D Small-Angle Light Scattering patterns showed a pronounced effect of temperature in terms of the evolution of large hydrophobic clusters, an event precluded when high concentrations of the longer chain surfactants were used.     

Interactions of a hydrophobically modified polymer with oppositely charged surfactants

The interaction of a hydrophobically modified anionic polymer (PMAOVE) with a cationic surfactant (DTAB) was studied using a multi-technique approach: turbidity, surface tension, and viscosity measurements, as well as EPR (5-doxyl stearic acid) and fluorescence (pyrene) probe techniques were used. In the investigated pH range (4-10), the cationic surfactant headgroups interact with the anionic carboxylic groups of the polymer backbone. In addition, nonpolar interactions of the surfactant chains with the n-octyl chains of PMAOVE stabilize the PMAOVE-DTAB complexes. Charge neutralization of the anionic polymer by the cationic surfactant leads to precipitation of the PMAOVE-DTAB complex at a certain DTAB concentration range. Further addition of DTAB causes a charge reversal of the complex and, subsequently, resolubilization of the precipitate. At an acidic pH (pH = 4), a second precipitation was observed, which is probably caused by conformational changes in the PMAOVE-DTAB complex. This second precipitate can be resolubilized by further addition of surfactant. At a neutral and basic pH, this second precipitation is absent. EPR analysis indicates that the surfactants form an ordered structure at the extended polymer chain at a neutral and basic pH, whereas at an acidic pH, a less ordered surfactant layer is formed on the coiled polymer with more hydrophobic microdomains.     

Presence or absence of counterion specificity in the interaction of alkylammonium surfactants with alkylacrylamide gels

Patterns in the interaction of cationic surfactants with nonionic polymer gels, which were inferred from a recent study from our laboratory, are confirmed by measurements of a series of alkylammonium surfactants with different counterions with a series of alkyl acrylamide gels of increasing hydrophobicity. Two swelling patterns were observed: Either the swelling continued above the surfactant critical micelle concentration (cmc) and the maximum swelling differed for different counterions and increased in the order of Br-相似文献   

New one-pot technique to introduce charged nanoparticles into a lyotropic liquid crystal matrix

We present a new method to incorporate hydrophilic charged nanoparticles into the lyotropic liquid crystal (LLC) template. This method is based on the effect of the polymer-induced phase separation (PIPS) and consists of two steps. In the first step, the nanoparticles are mixed with a surfactant micellar solution. In the second step, upon addition of polymer, phase separation is induced and the LLC phase doped with the nanoparticles is formed. Columnar hexagonal and lamellar LLC templates are obtained with the PIPS method. The ordering of the LLC phase can be controlled by the amount of polymer added to induce phase separation. The method works both for the system of nonionic surfactants and polymers and ionic surfactants and polyelectrolytes. We demonstrate that the PIPS method enables the fabrication of the LLC templates doped with positively or negatively charged nanoparticles as well as with a mixture of oppositely charged nanoparticles in arbitrary proportions.     

Polymer-surfactant and protein-surfactant interactions

The phase behavior and some physicochemical properties of homopolymers (HP) and hydrophobically modified (HMP) polymers, as well as of polyelectrolytes (PE) and proteins (PR), in the presence of aqueous surfactants, or their mixtures, are discussed. Mixing the above components gives rise to the formation of organized phases, whose properties are controlled by polymer and/or surfactant content, temperature, pH, and ionic strength. Depending on the nature, concentration, and net charge of both solutes, molecular solutions, polymer-surfactant complexes, adsorption onto micelles and vesicles, gels, liquid crystalline phases, and precipitates are observed. Such rich polymorphic behavior is the result of a complex balance between electrostatic, excluded volume, van der Waals, and other contributions to overall system stability. It is also modulated by the molecular details and architecture of both the polymer and the surfactant. Different experimental methods allow investigation of the above systems and getting information on the nature of polymer-surfactant interactions (PSI). Surface adsorption and thermodynamic methods, together with investigation of the phase diagrams, give information on the forces controlling PSI and on the existence of different phases. Conductivity, QELS and viscosity allow estimating the size and shape of polymer-surfactant (protein-surfactant) complexes. Optical microscopy, cryo-TEM, AFM, NMR, fluorescence, and relaxation methods give more information on the above systems. Use of the above mixtures in controlling gelation, surface covering, preparing dielectric layers, and drug release is suggested.     

Superchaotropic Nano-ion Binding as a Gelation Motif in Cellulose Ether Solutions

Nanometer-sized anions (nano-ions) like polyoxometalates and boron clusters exhibit so-called superchaotropic behavior, which describes their strong binding to hydrated non-ionic matter in water. We show here that nano-ions, at millimolar concentrations, dramatically enhance the viscosity and induce gelation of aqueous solutions of non-ionic cellulose ethers (CEs), a class of widely utilized polymers known for their thickening and gel-forming ability. These phenomena arise from an interplay of attractive forces and repulsive electrostatic forces between CE-chains upon nano-ion binding. The attractive forces manifest themselves as aggregation of CE-chains into a physically crosslinked polymer network (gel). In turn, the electrostatic repulsions hamper the viscosity increase and gelation. Superchaotropic nano-ion binding emerges as a novel and general physical crosslinking motif for CE-solutions and exceeds by far the conventional thickening effects of classical salts and ionic surfactants.     

Binding of surfactants to hydrophobically modified polymers

Recent progress in the understanding of the binding of surfactants to hydrophobically modified polymers (HMP), and the consequences of such binding, is reviewed. HMP are water-soluble polymers onto which low proportions of hydrophobic sidechains (hydrophobes) have been grafted. In an aqueous environment, the HMP hydrophobes associate among themselves and with added surfactant molecules into micelle-like aggregates. An HMP may therefore be considered as a ‘modified surfactant’, and the binding of surfactants to HMP is analogous to the mixed micellisation in mixed surfactant solutions. The binding isotherm gives the concentration of free (monomeric) surfactant and the stoichiometry of the HMP/surfactant complex at different total compositions. In mixtures involving ionic surfactants, it is found that the free surfactant often dominates, and gives important contributions to the ionic strength. Characteristic properties of HMP/surfactant mixtures may be related to stoichiometries of the mixed complexes. Thus, the maximum in solution viscosity, which is commonly found in HMP/surfactant mixtures, occurs at a similar hydrophobe stoichiometry (ratio of bound surfactant to HMP hydrophobe) for many different systems, although the total concentrations of surfactant at the maximum may vary by orders of magnitude, depending on the surfactant cmc. The solubility of a complex of oppositely charged HMP and surfactant is related to the charge stoichiometry of the complex. The phase separation/redissolution phenomena occurring in the bulk solution influence the HMP adsorption to surfaces and the forces between surfaces with adsorbed HMP.