Controllable Synthesis of NiCo LDH Nanosheets for Fabrication of High‐Performance Supercapacitor Electrodes

A unipolar pulse electrodeposition method was employed to controllably synthesize nanosheet type NiCo LDH. The effect of concentration rate of Ni(NO₃)₂/Co(NO₃)₂ preparation solution on crystalline structure, morphology and supercapacitive performance was investigated systematically. Experimental found that the morphology and composition of NiCo LDH was highly depend on the Ni²⁺/Co²⁺ molar ratios of preparation solution; and the obtained Ni_0.76Co_0.24 LDH materials showed small nanosheet size and uniform distribution on carbon fiber electrode. Ni_0.76Co_0.24 LDH electrode was evaluated for supercapacitor application, which revealed a high specific capacitances of 2189.8 and 1908.8 F g⁻¹ at the current density of 1 and 30 A g⁻¹ respectively and a good cycle stability, retaining 70.3 % of the initial capacitance after 20000 charge and discharge cycles at 50 A g⁻¹. Moreover, the Ni_0.76Co_0.24 LDH electrode exhibits a high energy density of 76 Wh Kg⁻¹ at a power density of 250 W Kg⁻¹ and a high power density of 7500 W Kg⁻¹ at energy density of 66 Wh Kg⁻¹. The as‐prepared Ni_0.76Co_0.24 LDH as positive electrode for asymmetric supercapacitor exhibits excellent energy density of 4.1 Wh Kg^‐1 at a power density of 4000 W Kg^‐1     

Concerted and Selective Electrooxidation of Polyethylene-Terephthalate-Derived Alcohol to Glycolic Acid at an Industry-Level Current Density over a Pd−Ni(OH)2 Catalyst

Electro-reforming of Polyethylene-terephthalate-derived (PET-derived) ethylene glycol (EG) into fine chemicals and H₂ is an ideal solution to address severe plastic pollution. Here, we report the electrooxidation of EG to glycolic acid (GA) with a high Faraday efficiency and selectivity (>85 %) even at an industry-level current density (600 mA cm⁻² at 1.15 V vs. RHE) over a Pd−Ni(OH)₂ catalyst. Notably, stable electrolysis over 200 h can be achieved, outperforming all available Pd-based catalysts. Combined experimental and theoretical results reveal that 1) the OH* generation promoted by Ni(OH)₂ plays a critical role in facilitating EG-to-GA oxidation and removing poisonous carbonyl species, thereby achieving high activity and stability; 2) Pd with a downshifted d-band center and the oxophilic Ni can synergistically facilitate the rapid desorption and transfer of GA from the active Pd sites to the inactive Ni sites, avoiding over-oxidation and thus achieving high selectivity.     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的Pd-Ni/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 mA·cm^-2,并且催化剂催化活性稳定。     

Stepwise Assembly of MII7 Clusters Revealed by Mass Spectrometry,EXAFS, and Crystallography

The square‐planar monomer NiL₂ ( Ni₁ ), L=2‐ethoxy‐6‐(N‐methyl‐iminomethyl)phenolate, reacts with M(H₂O)₆(ClO₄)₂, M=Ni or Co, to form heptanuclear disks [Co_xNi_7?x(OH)₆(L)₆](ClO₄)₂ ? 2 CH₃CN ( Co _x Ni_7?x , x=0–7) and the co‐crystal [Co_xNi_7?x(OH)₆L₆][NiL₂](ClO₄)₂ ? 2 CH₃CN ( Co _x Ni_7?x ‐Ni₁ ) under ambient conditions. It has proved possible to explore the bottom‐up assembly process of Co _x Ni_7?x and Co _x Ni_7?x ‐Ni₁ in real time. The final products have been characterized by thermogravimetric analysis, IR, elemental analysis, ICP‐MS, and single‐crystal X‐ray diffraction. Time‐dependent mass spectrometry (MS) revealed the following reaction steps: Ni₁→[M₂L₃]⁺→[M₄(OH)₂L₄]²⁺→[M₇(OH)₆L₆]²⁺. In contrast, the reaction of Ni₁ with Zn²⁺ only reaches halfway, and crystallographic evidence indicates a butterfly structure for [Zn₂Ni₂(OH)₂Cl₂] ( Zn₂Ni₂ ), an intermediate that is difficult to isolate in the above Ni‐Co series. A summation method has been used to analyze the MS of bimetallic clusters with very similar atomic masses, as is the case for Co and Ni. The results provide ample information on the distribution of Co and Ni within each cluster and their statistical distribution within selected crystals.     

Crystal structure and magnetism of layered Ln2Ca2MnNiO8 (Ln=Pr,Nd, Sm,and Gd) compounds

We report the syntheses, crystal structure, and magnetic properties of a series of distorted K₂NiF₄-type oxides Ln₂Ca₂MnNiO₈ (Ln=Pr, Nd, Sm, and Gd) in which Ln/Ca and Mn/Ni atoms randomly occupy the K and Ni sites respectively. The Ln=La compound does not form. These compounds show systematic distortions from the ideal tetragonal K₂NiF₄ structure (space group I4/mmm) to an orthorhombic structure (space group Pccn) with buckled MO₂ (M=Mn/Ni) layers. The degree of distortion is increased as the size of Ln decreases. Based on the magnetic data and X-ray absorption near edge spectra, we assigned Mn^IV and Ni^II. The Curie–Weiss plots of the high temperature magnetic data suggest strong ferromagnetic interactions probably due to Mn^IV–O–Ni^II linkages, implying local ordering of Mn/Ni ions to form ferromangnetic clusters in the MO₂ layers. At low temperatures below 110–130 K, these compounds show antiferromagnetic behaviors because of Mn^IV–O–Mn^IV and/or Ni^II–O–Ni^II contacts between the ferromagnetic clusters. The Ln=Pr and Nd compounds show additional antiferromagnetic signals that we attribute to the interlayer interactions between the clusters mediated by the Pr³⁺ and Nd³⁺ ions in the interlayer spaces. The present compounds show many parallels with the previously reported Ln₂Sr₂MnNiO₈ compounds.     

Co(OH)2/Ni(OH)2复合电极材料制备及其超级电容性质

以Co(NO_3)_2·6H_2O和Ni(NO_3)_2·6H_2O为钴源和镍源,采用溶剂热法一步合成了Co(OH)_2/Ni(OH)_2复合材料,通过煅烧该复合材料可得到NiCo_2O_4。采用XRD、SEM、BET等对材料进行了表征,结果表明,Co(OH)_2/Ni(OH)_2复合材料是薄片组成的花状形貌,比表面积为37. 48m~2/g。电化学性能测试表明,Co(OH)_2/Ni(OH)_2复合材料比NiCo_2O_4具有更高的比电容值和容量保持率。在0. 5A/g的电流密度下,复合材料比电容值可达到1097. 8F/g,而NiCo_2O_4比电容值仅为86. 1F/g。因此,与煅烧后的NiCo_2O_4材料相比,Co(OH)_2/Ni(OH)_2复合材料具有更加优良的电化学性能,这为高性能超级电容器材料的制备提供了一个新思路。     

Insertion of Molecular Oxygen in Transition‐Metal Hydride Bonds,Oxygen‐Bond Activation,and Unimolecular Dissociation of Metal Hydroperoxide Intermediates. Short Communication

Thermal activation of molecular oxygen is observed for the late‐transition‐metal cationic complexes [M(H)(OH)]⁺ with M=Fe, Co, and Ni. Most of the reactions proceed via insertion in a metal? hydride bond followed by the dissociation of the resulting metal hydroperoxide intermediate(s) upon losses of O, OH, and H₂O. As indicated by labeling studies, the processes for the Ni complex are very specific such that the O‐atoms of the neutrals expelled originate almost exclusively from the substrate O₂. In comparison to the [M(H)(OH)]⁺ cations, the ion? molecule reactions of the metal hydride systems [MH]⁺ (M=Fe, Co, Ni, Pd, and Pt) with dioxygen are rather inefficient, if they occur at all. However, for the solvated complexes [M(H)(H₂O)]⁺ (M=Fe, Co, Ni), the reaction with O₂ involving O? O bond activation show higher reactivity depending on the transition metal: 60% for the Ni, 16% for the Co, and only 4% for the Fe complex relative to the [Ni(H)(OH)]⁺/O₂ couple.     

Infrared Multiple Photon Dissociation Spectroscopy of Hydrated Cobalt Anions Doped with Carbon Dioxide CoCO2(H2O)n−, n=1–10, in the C−O Stretch Region

We investigate anionic [Co,CO₂,nH₂O]⁻ clusters as model systems for the electrochemical activation of CO₂ by infrared multiple photon dissociation (IRMPD) spectroscopy in the range of 1250–2234 cm⁻¹ using an FT-ICR mass spectrometer. We show that both CO₂ and H₂O are activated in a significant fraction of the [Co,CO₂,H₂O]⁻ clusters since it dissociates by CO loss, and the IR spectrum exhibits the characteristic C−O stretching frequency. About 25 % of the ion population can be dissociated by pumping the C−O stretching mode. With the help of quantum chemical calculations, we assign the structure of this ion as Co(CO)(OH)₂⁻. However, calculations find Co(HCOO)(OH)⁻ as the global minimum, which is stable against IRMPD under the conditions of our experiment. Weak features around 1590–1730 cm⁻¹ are most likely due to higher lying isomers of the composition Co(HOCO)(OH)⁻. Upon additional hydration, all species [Co,CO₂,nH₂O]⁻, n≥2, undergo IRMPD through loss of H₂O molecules as a relatively weakly bound messenger. The main spectral features are the C−O stretching mode of the CO ligand around 1900 cm⁻¹, the water bending mode mixed with the antisymmetric C−O stretching mode of the HCOO⁻ ligand around 1580–1730 cm⁻¹, and the symmetric C−O stretching mode of the HCOO⁻ ligand around 1300 cm⁻¹. A weak feature above 2000 cm⁻¹ is assigned to water combination bands. The spectral assignment clearly indicates the presence of at least two distinct isomers for n ≥2.     

In Situ Growth of Hierarchical Ni-Mn-O Solid Solution on a Flexible and Porous Ni Electrode for High-Performance All-Solid-State Asymmetric Supercapacitors

To endow all-solid-state asymmetric supercapacitors with high energy density, cycling stability, and flexibility, we design a binder-free supercapacitor electrode by in situ growth of well-distributed broccoli-like Ni_0.75Mn_0.25O/C solid solution arrays on a flexible and three-dimensional Ni current collector (3D-Ni). The electrode consists of a bottom layer of compressed but still porous Ni foam with excellent flexibility and high electrical conductivity, an intermediate layer of interconnected Ni nanoparticles providing a large specific surface area for loading of active substances, and a top layer of vertically aligned mesoporous nanosheets of a Ni_0.75Mn_0.25O/C solid solution. The resultant 3D-Ni/Ni_0.75Mn_0.25O/C cathode exhibits a specific capacitance of 1657.6 mF cm⁻² at 1 mA cm⁻² and shows no degradation of the capacitance after 10 000 cycles at 3 mA cm⁻². The assembled 3D-Ni/Ni_0.75Mn_0.25O/C//activated carbon asymmetric supercapacitor has a high specific capacitance of 797.7 mF cm⁻² at 2 mA cm⁻² and an excellent cycling stability with 85.3 % of capacitance retention after 10 000 cycles at a current density of 3 mA cm⁻². The energy density and power density of the asymmetric supercapacitor are up to 6.6 mW h cm⁻³ and 40.8 mW cm⁻³, respectively, indicating a fairly promising future of the flexible 3D-Ni/Ni_0.75Mn_0.25O/C electrode for efficient energy storage applications.     

In Situ and Theoretical Studies for the Dissociation of Water on an Active Ni/CeO2 Catalyst: Importance of Strong Metal–Support Interactions for the Cleavage of O–H Bonds

Water dissociation is crucial in many catalytic reactions on oxide‐supported transition‐metal catalysts. Supported by experimental and density‐functional theory results, the effect of the support on O? H bond cleavage activity is elucidated for nickel/ceria systems. Ambient‐pressure O 1s photoemission spectra at low Ni loadings on CeO₂(111) reveal a substantially larger amount of OH groups as compared to the bare support. Computed activation energy barriers for water dissociation show an enhanced reactivity of Ni adatoms on CeO₂(111) compared with pyramidal Ni₄ particles with one Ni atom not in contact with the support, and extended Ni(111) surfaces. At the origin of this support effect is the ability of ceria to stabilize oxidized Ni²⁺ species by accommodating electrons in localized f‐states. The fast dissociation of water on Ni/CeO₂ has a dramatic effect on the activity and stability of this system as a catalyst for the water‐gas shift and ethanol steam reforming reactions.     

＂Intelligent＂ reforming catalysts： Trace noble metal-doped Ni/Mg（A1）O derived from hydrotalcites

Trace amounts of noble metal-doped Ni/Mg(Al)O catalysts were prepared starting from Mg-Al hydrotalcites (HTs) and tested in daily start-up and shut-down (DSS) operation of steam reforming (SR) of methane or partial oxidation (PO) of propane. Although Ni/Mg(Al)O catalysts prepared from Mg(Ni)-Al HT exhibited high and stable activity in stationary SR, PO and dry reforming of methane and propane, the Ni/Mg(Al)O catalysts were drastically deactivated due to Ni oxidation by steam as purge gas when they were applied in DSS SR ofmethane. Such deactivation was effectively suppressed by doping trace amounts of noble metal on the catalysts by using a “memory effect” of HTs. Moreover, the noble metal-doped Ni/Mg(Al)O catalysts exhibited “intelligent” catalytic behaviors, i.e., self-activation and self-regenerative activity, leading to high and sustainable activity during DSS operation. Pt was the most effective among noble metals tested. The self-activation occurred by the reduction of Ni2+ in Mg(Ni,Al)O periclase to Ni0 assisted by hydrogen spillover from Pt (or Pt-Ni alloy). The self-regenerative activity was accomplished by self-redispersion of active Ni0 particles due to a reversible reductionoxidation movement of Ni between the outside and the inside of the Mg(Al)O periclase crystal; surface Ni0 was oxidized to Ni2+ by steam and incorporated into Mg(Ni2+,Al)O periclase, whereas the Ni2+ in the periclase was reduced to Ni0 by the hydrogen spillover and appeared as the fine Ni0 particles on the catalyst surface. Further a “green” preparation of the Pt/Ni/[Mg3.5Al]O catalysts was accomplished starting from commercial Mg3.5-Al HT by calcination, followed by sequential impregnation of Ni and Pt.     

One-Step Approach for Constructing High-Density Single-Atom Catalysts toward Overall Water Splitting at Industrial Current Densities

The construction of highly active, durable, and cost-effective catalysts is urgently needed for green hydrogen production. Herein, catalysts consisting of high-density Pt (24 atoms nm⁻²) and Ir (32 atoms nm⁻²) single atoms anchored on Co(OH)₂ were constructed by a facile one-step approach. Remarkably, Pt₁/Co(OH)₂ and Ir₁/Co(OH)₂ only required 4 and 178 mV at 10 mA cm⁻² for hydrogen evolution reaction and oxygen evolution reaction, respectively. Moreover, the assembled Pt₁/Co(OH)₂//Ir₁/Co(OH)₂ system showed mass activity of 4.9 A mg_{noble metal}⁻¹ at 2.0 V in an alkaline water electrolyzer, which is 316.1 times higher than that of Pt/C//IrO₂. Mechanistic studies revealed that reconstructed Ir−O₆ single atoms and remodeled Pt triple-atom sites enhanced the occupancy of Ir−O bonding orbitals and improved the occupation of Pt−H antibonding orbital, respectively, contributing to the formation of the O−O bond and the desorption of hydrogen. This one-step approach was also generalized to fabricate other 20 single-atom catalysts.     

A New Domain of Reactivity for High‐Valent Dinuclear [M(μ‐O)2M′] Complexes in Oxidation Reactions

The strikingly different reactivity of a series of homo‐ and heterodinuclear [(M^III)(μ‐O)₂(M^III)′]²⁺ (M=Ni; M′=Fe, Co, Ni and M=M′=Co) complexes with β‐diketiminate ligands in electrophilic and nucleophilic oxidation reactions is reported, and can be correlated to the spectroscopic features of the [(M^III)(μ‐O)₂(M^III)′]²⁺ core. In particular, the unprecedented nucleophilic reactivity of the symmetric [Ni^III(μ‐O)₂Ni^III]²⁺ complex and the decay of the asymmetric [Ni^III(μ‐O)₂Co^III]²⁺ core through aromatic hydroxylation reactions represent a new domain for high‐valent bis(μ‐oxido)dimetal reactivity.     

Rapid Charge Transfer Endowed by Interfacial Ni-O Bonding in S-scheme Heterojunction for Efficient Photocatalytic H2 and Imine Production

Cooperative coupling of H₂ evolution with oxidative organic synthesis is promising in avoiding the use of sacrificial agents and producing hydrogen energy with value-added chemicals simultaneously. Nonetheless, the photocatalytic activity is obstructed by sluggish electron-hole separation and limited redox potentials. Herein, Ni-doped Zn_0.2Cd_0.8S quantum dots are chosen after screening by DFT simulation to couple with TiO₂ microspheres, forming a step-scheme heterojunction. The Ni-doped configuration tunes the highly active S site for augmented H₂ evolution, and the interfacial Ni−O bonds provide fast channels at the atomic level to lower the energy barrier for charge transfer. Also, DFT calculations reveal an enhanced built-in electric field in the heterojunction for superior charge migration and separation. Kinetic analysis by femtosecond transient absorption spectra demonstrates that expedited charge migration with electrons first transfer to Ni²⁺ and then to S sites. Therefore, the designed catalyst delivers drastically elevated H₂ yield (4.55 mmol g⁻¹ h⁻¹) and N-benzylidenebenzylamine production rate (3.35 mmol g⁻¹ h⁻¹). This work provides atomic-scale insights into the coordinated modulation of active sites and built-in electric fields in step-scheme heterojunction for ameliorative photocatalytic performance.     

Non-Interacting Ni and Fe Dual-Atom Pair Sites in N-Doped Carbon Catalysts for Efficient Concentrating Solar-Driven Photothermal CO2 Reduction

Solar-to-chemical energy conversion under weak solar irradiation is generally difficult to meet the heat demand of CO₂ reduction. Herein, a new concentrated solar-driven photothermal system coupling a dual-metal single-atom catalyst (DSAC) with adjacent Ni−N₄ and Fe−N₄ pair sites is designed for boosting gas-solid CO₂ reduction with H₂O under simulated solar irradiation, even under ambient sunlight. As expected, the (Ni, Fe)−N−C DSAC exhibits a superior photothermal catalytic performance for CO₂ reduction to CO (86.16 μmol g⁻¹ h⁻¹), CH₄ (135.35 μmol g⁻¹ h⁻¹) and CH₃OH (59.81 μmol g⁻¹ h⁻¹), which are equivalent to 1.70-fold, 1.27-fold and 1.23-fold higher than those of the Fe−N−C catalyst, respectively. Based on theoretical simulations, the Fermi level and d-band center of Fe atom is efficiently regulated in non-interacting Ni and Fe dual-atom pair sites with electronic interaction through electron orbital hybridization on (Ni, Fe)−N−C DSAC. Crucially, the distance between adjacent Ni and Fe atoms of the Ni−N−N−Fe configuration means that the additional Ni atom as a new active site contributes to the main *COOH and *HCO₃ dissociation to optimize the corresponding energy barriers in the reaction process, leading to specific dual reaction pathways (COOH and HCO₃ pathways) for solar-driven photothermal CO₂ reduction to initial CO production.     

ZnO and TiO2 clusters as catalyst in the addition and abstraction reaction of acrylic acid with the OH radical

The present work displays the theoretical analysis on the role of metal oxide clusters as an effective catalyst in the reaction between acrylic acid and OH radical, which has an energy barrier of 12.4 kcal/mol. The formation of metal oxide cluster such as ZnO and TiO₂ with varying size from monomer to hexamer is analyzed using cohesive energy, which increases with cluster size. Adsorption of acrylic acid on clusters reveals that dimer ZnO and tetramer TiO₂ are good adsorbed entities. The dimer ZnO and tetramer TiO₂ clusters have reduced the barrier height. However, from the thermodynamical analysis of H-abstraction and OH addition reaction, the dimer ZnO cluster is found to be a good catalyst than a tetramer TiO₂ cluster. The favorable H abstraction and OH addition reactions are feasible at the active methylene group (–CH). OH addition reactions dominate over the H abstraction reaction. Further, the presence of metal oxide clusters enhances the rate of the reaction between acrylic acid and OH radical. The kinetics of the favorable reaction with a dimer ZnO cluster has a rate constant of 7.80 × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹, which is higher than the literature report (1.75 × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹). Overall, ZnO and TiO₂ metal oxide clusters can be effectively utilized as catalyst.     

Surface Reorganization on Electrochemically-Induced Zn–Ni–Co Spinel Oxides for Enhanced Oxygen Electrocatalysis

Herein, we highlight redox-inert Zn²⁺ in spinel-type oxide (Zn_XNi_1−XCo₂O₄) to synergistically optimize physical pore structure and increase the formation of active species on the catalyst surface. The presence of Zn²⁺ segregation has been identified experimentally and theoretically under oxygen-evolving condition, the newly formed V_Zn−O−Co allows more suitable binding interaction between the active center Co and the oxygenated species, resulting in superior ORR performance. Moreover, a liquid flow Zn–air battery is constituted employing the structurally optimized Zn_0.4Ni_0.6Co₂O₄ nanoparticles supported on N-doped carbon nanotube (ZNCO/NCNTs) as an efficient air cathode, which presents remarkable power density (109.1 mW cm⁻²), high open circuit potential (1.48 V vs. Zn), excellent durability, and high-rate performance. This finding could elucidate the experimentally observed enhancement in the ORR activity of Zn_XNi_1−XCo₂O₄ oxides after the OER test.     

Single-Atom Nickel on Carbon Nitride Photocatalyst Achieves Semihydrogenation of Alkynes with Water Protons via Monovalent Nickel

Prospects in light-driven water activation have prompted rapid progress in hydrogenation reactions. We describe a Ni²⁺−N₄ site built on carbon nitride for catalyzed semihydrogenation of alkynes, with water supplying protons, powered by visible-light irradiation. Importantly, the photocatalytic approach developed here enabled access to diverse deuterated alkenes in D₂O with excellent deuterium incorporation. Under visible-light irradiation, evolution of a four-coordinate Ni²⁺ species into a three-coordinate Ni⁺ species was spectroscopically identified. In combination with theoretical calculations, the photo-evolved Ni⁺ is posited as HO−Ni⁺−N₂ with an uncoordinated, protonated pyridinic nitrogen, formed by coupled Ni²⁺ reduction and water dissociation. The paired Ni−N prompts hydrogen liberation from water, and it renders desorption of alkene preferred over further hydrogenation to alkane, ensuring excellent semihydrogenation selectivity.     

碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的PdNi/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 m A·cm~(-2),并且催化剂催化活性稳定。     

Regulating the Coordination Environment of MOF-Templated Single-Atom Nickel Electrocatalysts for Boosting CO2 Reduction

The general synthesis and control of the coordination environment of single-atom catalysts (SACs) remains a great challenge. Herein, a general host–guest cooperative protection strategy has been developed to construct SACs by introducing polypyrrole (PPy) into a bimetallic metal–organic framework. As an example, the introduction of Mg²⁺ in MgNi-MOF-74 extends the distance between adjacent Ni atoms; the PPy guests serve as N source to stabilize the isolated Ni atoms during pyrolysis. As a result, a series of single-atom Ni catalysts (named Ni_SA-N_x-C) with different N coordination numbers have been fabricated by controlling the pyrolysis temperature. Significantly, the Ni_SA-N₂-C catalyst, with the lowest N coordination number, achieves high CO Faradaic efficiency (98 %) and turnover frequency (1622 h⁻¹), far superior to those of Ni_SA-N₃-C and Ni_SA-N₄-C, in electrocatalytic CO₂ reduction. Theoretical calculations reveal that the low N coordination number of single-atom Ni sites in Ni_SA-N₂-C is favorable to the formation of COOH* intermediate and thus accounts for its superior activity.