Evaluation of the (Allyl alcohol 1,2‐butoxylate‐block‐etoxylate)‐b‐PMMA Copolymers Composition by the Dielectric Measurements

Redox initiated free‐radical polymerization of methyl methacrylate (MMA) with allyl alcohol 1,2‐butoxylate‐block‐etoxylate (AABE) was carried out to yield AABE‐b‐PMMA copolymers at elevated temperatures. The composition of the copolymers depending on the polymerization temperature was qualitatively estimated by the dielectric measurements. It has been seen that AABE segment quantity decreased and PMMA segment quantity increased with increasing the polymerization temperature. The dielectric constant and the dissipation factor of the copolymers were investigated as a function of frequency and temperature. The dielectric constant and the dissipation factor were found to be strongly affected by the polymerization temperature. The highest dielectric constant in all studied temperatures and frequencies was obtained in the case of the copolymer which was prepared at 313 K. The dipolar C‐O and OH groups of the AABE segment have the primary effect on the dielectric constant. The copolymer which was prepared at 323 K, showed the highest dissipation factor near the relaxation temperature of PMMA.     

KINETICS OF SUSPENDED EMULSION POLYMERIZATION OF METHYL METHACRYLATE*

 The kinetics of suspended emulsion polymerization of methyl methacrylate (MMA), in which water acted as the dispersed phase and the mixture of MMA and cyclohexane as the continuous phase, was investigated. It showed that the initial polymerization rate (R_p0) and steady-state polymerization rate (R_p) were proportional to the mass ratio between water and oil phase, and increased as the polymerization temperature, the potassium persulphate concentration ([I]) and the Tween20 emulsifier concentration ([S]) increased. The relationships between the polymerization rate and [I] and [S] were obtained as follows: R_p0∝[I]^0.71[S]^0.23.The above exponents were close to those obtained from normal MMA emulsion polymerization. It also showed that the average molecular weight of the resulting poly(methylmethacrylate) decreased as the polymerization temperature,[I]and [S] increased. Thus, MMA suspended emulsion polymerization could be considered as a combination of many miniature emulsion polymerizations proceeding in water drops and obeyed the classical kinetics of MMA emulsion polymerization.     

Oxidative polymerization of acrylamide in the presence of thioglycolic acid

Chemical polymerization of acrylamide at room temperature was examined by using thioglycolic acid-cerium (IV) sulfate and thioglycolic acid-KMnO₄ redox systems in acid aqueous medium. Water soluble polyacrylamides containing thioglycolic acid end groups were synthesized. The effects of the molar ratio of acrylamide to Ce(IV) n _AAm /n _Ce(IV) , the polymerization time, the temperature, the monomer concentration, the molar ratio of cerium (IV) sulfate to thioglycolic acid and the concentration of sulfuric acid on the yield and molecular weight of polymer were investigated. Lower molar ratios of acrylamide/Ce(IV) at constant monomer concentration resulted in an increase in the yield but a decrease in molecular weight of polymer. The increase of reaction temperature from 20 to 70°C resulted in a decrease in the yield but generally resulted in a constant value for the molecular weight of polymer. With increasing polymerization time, the yield and molecular weight of polymer did not change substantially. Ce(IV) and Mn(VII) ions are reduced to Ce(III) and Mn(II) ions respectively in the polymerization reaction. The existence of Ce(III) ion bound to polymer was investigated by UV-visible spectrophotometry and fluoresce measurements. The amount of Mn(II) incorporated into the polymer was determined using graphite furnace atomic absorption spectrometry. The mechanism of this phenomenon is discussed.     

Redox-Initiated Polymerization of Methyl Methacrylate

The redox-initiated polymerization of methyl methacrylate (MMA) by the Ce(IV)-malic acid system has been carried out in aqueous medium under an inert atmosphere. The rate of polymerization was found to be proportional to [MMA]^3/2 [MA]^1/2 [Ce(IV)]^1/2 and the rate of ceric ion disappearance was proportional to [Ce(IV)] but independent of [MMA]. The rate increased linearly up to a certain range of [MA], above which it remained constant. Increasing [H₂SO₄] decreased the rate. The activation energy was found to be 57.44 kJ/mol.     

Polymerization of MMA catalyzed by different novel mixed ligand lanthanocene{(Cp)(Cl) LnSchiff-base (THF)},(COT) -Ln(methoxyethylindenyl)(THF) /Al (i -Bu)_3 systems

This article deals that the rare earth metal complexes along with Al(i'-Bu),can catalyze the polymerization of methyl-methacrylate (MMA) into high molecular weight poly(MMA) along with narrow molecular weight distributions (MWD).A typical example was mentioned in the case of {Cp(Cl) Sm-Schiff-base(THF)} which expresses maximum (conv.% = 55.46 and Mn=354×103) efficiency along with narrow MWD (Mw/Mn<2) at 60℃.The resulting polymer was partially syndiotactic (>60%).The effect of the catalyst,temperature,catalyst/MMA molar ratio,catalyst/Al( i-Bu)3 molar ratio on the polymerization of MMA at 60℃ were also investigated.     

Kinetics of emulsion copolymerization of methylmethacrylate and ethylacrylate: effect of type and concentration of initiator in unseeded polymerization system

The free radical emulsion copolymerization of methylmethacrylate (MMA) and ethylacrylate (EA) initiated by a water-soluble initiator (potassium persulphate, KPS) at 50 °C in the presence of anionic emulsifier above critical micelle concentration under constant stirring speed in an inert atmosphere is investigated. The effect of blend of KPS and oil-soluble initiators [KPS+2,2^′-azobisisobutyronitrile (AIBN)] is also examined. The order of the interval-II polymerization rate (R_p) is found to be 0.76±0.03 in KPS initiation alone and 0.72±0.04 in presence of fixed concentration of AIBN under similar experimental condition. On the other hand, interestingly, the rate of polymerization is found to be propotional to the 0.40th power of the AIBN concentration in presence of fixed concentration of KPS. The kinetic features of the present investigation indicate that probably the radical desorption is relatively facile and also the cage effect may be operative under high conversions (i.e. in polymer particles) in this MMA/EA emulsion copolymerization system. It is also found that the polydispersity index of polymer is being influenced by the type and concentration of initiators.     

Experimental studies on the ring opening polymerization of p-dioxanone using an Al(OPr)3-monosaccharide initiator system

The ring opening polymerization (ROP) of p-dioxanone using a protected monosaccharide (1,2;3,4-di-O-isopropylidene-α-d-galactopyranose)/Al(OⁱPr)₃ initiator system to yield polydioxanone with a protected monosaccharide end-group is described. The products were synthesized at 60-100 °C and characterized by ¹H and ¹³C NMR, and MALDI-TOF mass spectrometry. Besides the desired polydioxanone functionalised with a monosaccharide end-group, also polydioxanone with an OⁱPr end-group was formed (20-30%). Systematic studies showed that the polymer yield is a function of the reaction temperature and the reaction time, with higher temperatures (100 °C) leading to lower yields. The average chain length of the polymers is between 7 and 58 repeating units and may be tuned by the monomer to monosaccharide ratio (at constant Al(OⁱPr)₃ intake). A statistical model has been developed that successfully describes the experimentally observed relation between the average chain length of the functionalized polymer and reaction parameters.     

The WCl6-e-Al-CH2Cl2 catalyzed polypentenamer formation via ring-opening metathesis polymerization (ROMP)

The synthesis of polypentenamer by an electrochemically generated metathesis polymerization catalyst from methylene chloride solution of WCl₆ was investigated. The active species formed by electroreduction of this salt under controlled potential of +900 mV at a platinum cathode with an aluminum anode were found to catalyze the ring-opening metathesis polymerization (ROMP) of cyclopentene, monocyclic olefin of relatively low strain, in high yield (89%) and at short period (32 min) under mild conditions. The effect of reaction parameters, e.g., olefin/catalyst ratio, reaction time, electrolysis time, catalyst aging, on the polymerization yield have been studied. The resulting polymer has been characterized by ¹H and ¹³C NMR, IR and gel permeation chromatography (GPC) techniques. Analysis of the polypentenamer microstructure by means of ¹³C NMR spectroscopy indicates that the polymer contains a mainly trans stereoconfiguration of the double bonds (σ_c = 0.31) and a slightly blocky distribution (r_tr_c > 1) of cis and trans double bond dyads (r_tr_c = 1.44). However, this electrochemical system is reluctant to facilitate the competing vinyl type addition polymerization reactions.     

Coordination polymerization with the novel η-C20H17Ti(OPr)3 complex

Modified corannulene based transition metal complexes of titanium as a novel group of metallocene catalysts were synthesized and investigated in coordination polymerization reactions as catalysts in the syndiospecific bulk polymerization of styrene. In comparison to the zirconium complex exo-(η⁵-C₂₀H₁₇)(η⁵-C₅H₅)ZrCl₂, the titanium complex η⁵-C₂₀H₁₇Ti(OⁱPr)₃ shows a significantly increased polymerization activity, a considerably improved stereoregularity of the syndiotactic polymer chain, indicated by the increased melting temperature of 269 °C, as well as a higher weight average molecular weight and a narrower molecular weight distribution.     

A neutral Ni(II) acetylide-mediated radical polymerization of methyl methacrylate using the atom transfer radical polymerization method

A neutral nickel σ-acetylide complex [Ni(CCPh)₂(PBu₃)₂] (NBP) is used for possible atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in conjunction with an organic halide as an initiator [R-X: CCl₄, CH₃Cl, BrCCl₃, C₂H₅Br, and C₅H₉Br] in toluene at 80 °C. Among these initiating systems, BrCCl₃/NBP gave the best controlled radical polymerization of MMA and produced polymer with relatively narrow molecular weight distribution (M_w/M_n≈1.3). The ATRP of MMA is preliminarily identified by the following facts: (1) the present MMA polymerization initiated by BrCCl₃/NBP is completely hindered by the addition of TEMPO; (2) the conversion shows a typical linear variation with time in semilogarithmic coordinates; (3) the measured number-average molecular weights of polymer show a linear increase with conversion and agree closely with the theoretical values; (4) the resulting polymer chain contains a dormant carbon-halogen terminal.     

Selective uptake of plutonium (IV) on calcium alginate gel polymer and TBP microcapsule

The uptake behavior of Pu(IV) has been investigated by using calcium alginate gel polymer (CaALG) and TBP microcapsules (TBP-CaALG). The characterization of CaALG and TBP-CaALG was examined by SEM and IR, and the uptake properties and distribution of Pu(IV) ions were estimated by batch method. The uptake rate of Pu(IV) on CaALG and TBP-CaALG in the presence of 5 M HNO₃ was attained within 6 and 4 h, respectively, and K _d values for CaALG and TBP-CaALG after 7 h-shaking were 50.2 and 53.2 cm³/g, respectively. Relatively large K _d values (90.3–425 cm³/g) were obtained for fresh CaALG and TBP-CaALG in the presence of 0.5–2 M HNO₃. Thus CaALG and TBP-CaALG are effective for the separation of Pu(IV) in the presence of highly concentrated HNO₃.     

Synthesis of poly(methyl methacrylate) via ARGET ATRP and study of the effect of solvents and temperatures on its polymerization kinetics

This investigation reports the synthesis of poly(methyl methacrylate) via activators regenerated by electron transfer atom transfer radical polymerization (ARGET ATRP) and studies the effect of solvents and temperature on its polymerization kinetics. ARGET ATRP of methyl methacrylate (MMA) was carried out in different solvents and at different temperatures using CuBr₂ as catalyst in combination with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as a ligand. Methyl 2‐chloro propionate was used as ATRP initiator and ascorbic acid was used as a reducing agent in the ARGET ATRP of MMA. The conversion was measured gravimetrically. The semilogarithmic plot of monomer conversion versus time was found to be linear, indicating that the polymerization follows first‐order kinetics. The linear polymerization kinetic plot also indicates the controlled nature of the polymerization. N,N‐Dimethylformamide (DMF), tetrahydrofuran (THF), toluene, and methyl ethyl ketone were used as solvents to study the effect on the polymerization kinetics. The effect of temperature on the kinetics of the polymerization was also studied at various temperatures. It has been observed that polymerization followed first‐order kinetics in every case. The rate of polymerization was found to be highest (k_app = 6.94 × 10⁻³ min⁻¹) at a fixed temperature when DMF was used as solvent. Activation energies for ARGET ATRP of MMA were also calculated using the Arrhenius equation.     

Ring-opening polymerization of ε-caprolactone initiated by diphenylzinc

In the present work the polymerization of ε-caprolactone (ε-CL) using Ph₂Zn as initiator is reported. The effects of reaction temperature, molar ratio of monomer/initiator and reaction time on the yield and the molecular weight are investigated. The temperature is varied between 20 and 120 °C and the molar ratio of monomer to initiator between 200 and 800 mol/mol. The results indicate that the Ph₂Zn induces the polymerization of ε-CL to high conversion and produces polymer with high molecular weight at temperatures around 40-60 °C.     

Synthesis and MMA polymerization of chiral ansa-zirconocene ester enolate complexes with C2- and Cs-ligation

A series of chiral ansa-zirconocene ester enolate complexes incorporating C₂- or C_s-symmetric ligands, including neutral rac-(EBI)ZrCl[OC(OⁱPr)CMe₂] (1), rac-(EBI)Zr(OTf)[OC(OⁱPr)CMe₂] (2), rac-(EBI)Zr(OTf)[OC(OMe)C(Me)CH₂C(Me₂)C(OⁱPr)O] (3), [Me₂C(Cp)(Flu)]ZrMe[OC(OⁱPr)CMe₂] (4), and cationic [Me₂C(Cp)(Flu)]Zr⁺(THF)[OC(OⁱPr)CMe₂][MeB(C₆F₅)₃]⁻ (5), have been synthesized. Within the neutral C₂-ligated zirconocene ester enolate series, the chloride derivative 1 is inactive toward any methyl methacrylate (MMA) additions, the methyl derivative rac-(EBI)ZrMe[OC(OⁱPr)CMe₂] adds cleanly only 1 equiv. of MMA, and the triflate derivative 2 can add either 1 equiv. of MMA to form the single-MMA-addition product 3 or multiple equivalents of MMA to form P(MMA). Unlike the C_s-ligated methyl cation [Me₂C(Cp)(Flu)ZrMe]⁺, which is inactive for MMA polymerization under various conditions, the C_s-ligated ester enolate cation 5 is moderately active for polymerization of MMA and N,N-dimethylacrylamide at ambient temperature; the resulting P(MMA) has a high molecular weight of M_n = 388 000 Da but a low syndiotacticity of [rr] = 64%, and the polymerization conforms to a chain-end control mechanism.     

Synthesis characterizations and properties of a new fluoro-maleimide polymer

Novel 4-(4-trifluoromethyl)phenoxy N-phenyl-maleimide (FPMI) was synthesized. The free radical-initiated polymerization of FPMI was carried out in 1,4-dioxane solution using azobisisobutyronitrile as initiator. The monomer was investigated by FTIR, ¹H NMR, ¹³C NMR and elemental analysis, while the polymer was investigated by FTIR, ¹H NMR and ¹³C NMR. The effect of the monomer concentration, initiator concentration and temperature on the rate of polymerization (R_p) was studied. The activation energy of the polymerization was calculated (ΔE = 48.94 kJ/mol). The molecular weight of PFPMI and polydispersity index of the polymer were determined by gel permeation chromatography and were equal to 73,500, 16,700 and 2.27, respectively. The properties of PFPMI, including thermal behavior, thermal stability, the glass transition temperature (T_g = 236 °C), photo-stability, solubility and solution viscosity were studied.     

Reverse atom transfer radical polymerization of methyl methacrylate with a new catalytic system,FeCl3/isophthalic acid

A new catalytic system, FeCl₃/isophthalic acid, was successfully used in the reverse atom transfer radical polymerization (RATRP) of methyl methacrylate (MMA) in the presence of a conventional radical initiator, 2,2′‐azo‐bis‐isobutyrontrile. Well‐defined poly(methyl methacrylate) (PMMA) was synthesized in an N,N‐dimethylformamide solvent at 90–120 °C. The polymerization was controlled up to a molecular weight of 50,000, and the polydispersity index was 1.4. Chain extension was performed to confirm the living nature of the polymer. The kinetics of the RATRP of MMA with FeCl₃/isophthalic acid as the catalyst system was investigated. The apparent activation energy was 10.47 kcal/mol. The presence of the end chloride atom on the resulting PMMA was demonstrated by ¹H NMR spectroscopy. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 765–774, 2001     

Stereocontrol in the free‐radical polymerization of methacrylates with fluoroalcohols

The free‐radical polymerization of methyl methacrylate (MMA), ethyl methacrylate (EMA), isopropyl methacrylate (IPMA), and tert‐butyl methacrylate (t‐BuMA) was carried out under various conditions to achieve stereoregulation. In the MMA polymerization, syndiotactic specificity was enhanced by the use of fluoroalcohols, including (CF₃)₃COH as a solvent or an additive. The polymerization of MMA in (CF₃)₃COH at −98 °C achieved the highest syndiotacticity (rr = 93%) for the radical polymerization of methacrylates. Similar effects of fluoroalcohols enhancing syndiotactic specificity were also observed in the polymerization of EMA, whereas the effect was negligible in the IPMA polymerization. In contrast to the polymerizations of MMA and EMA, syndiotactic specificity was decreased by the use of (CF₃)₃COH in the t‐BuMA polymerization. The stereoeffects of fluoroalcohols seemed to be due to the hydrogen‐bonding interaction of the alcohols with monomers and growing species. The interaction was confirmed by NMR measurements. In addition, in the bulk polymerization of MMA at −78 °C, syndiotactic specificity and polymer yield increased even in the presence of a small amount {[(CF₃)₃COH]/[MMA]_o < 1} of (CF₃)₃COH. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4693–4703, 2000     

New Sn(IV) and Ti(IV) bis(trimethylsilyl)amides in d,l-lactide polymerization, SEM characterization of polymers

Ring-opening polymerization of d,l-lactide initiated with new chlorotris(bis(trimethylsilyl) amido) tin(IV), tetrakis(bis(trimethylsilyl)amido) tin(IV) and titanium(IV) was investigated. New complexes reveal practically quantitative conversion degrees and produced polymers with higher molecular weight with respect to reference alkoxo-species.The X-ray crystal structure of chlorotris(bis(trimethylsilyl)amido) tin (IV) was investigated. Axial enantiomerism of [SnCl{N(SiMe₃)₂}₃] molecules in solution was studied by high-field dynamic NMR, the value of Gibbs activation energy ΔG^‡ = 59.5 kJ/mol.Field emission SEM investigation of bulk polymer samples and thin films on conductive Al foil revealed a stratified fibrous textures in the bulk polymers, as well as nanoscaled topographical features due to coils and entanglements of individual macromolecules in thin films.     

Radical polymerization behavior of 3-(N-2-methacryloyloxyethyl-N,N-dimethyl)ammonatopropanesulfonate in water

The homogeneous polymerization of 3-(N-2-methacryloyloxyethyl-N,N-dimethyl)ammonatopropanesulfonate (MDAPS) with potassium peroxydisulfate (KPS) was kinetically in situ investigated in water by means of FT-near IR spectroscopy. The overall activation energy of the polymerization was calculated to be 16.0 kcal/mol. The initial polymerization rate (R_p) at 40 °C was expressed by R_p=k[KPS]^0.65[MDAPS]^1.0. The presence of alkaline metal salts was observed to accelerate the polymerization. The order of acceleration at 40 °C was CsCl > KCl > NaCl > LiCl when the chloride salts were used. NaCl showed higher acceleration effect than NaF. NaBr and NaI exhibited retardation and inhibition effect, respectively, because of reduction of KPS and its primary radical with bromide and iodide ions. The polymerization of MDAPS with KPS in water in the presence of NaCl at 2.0 mol/l gave R_p=k[KPS]^0.70[MDAPS]^1.4 at 40 °C. The overall activation energy of the polymerization in the presence of NaCl was estimated to be 11.6 kcal/mol being considerably lower value compared with that in its absence. The syndiotacticity of poly(MDAPS) tended to increase with rising temperature and decrease in the presence of NaCl.     

Emulsion polymerization of methyl methacrylate under pulsed microwave irradiation

Emulsion polymerization of methyl methacrylate (MMA) under pulsed microwave irradiation (PMI) with higher peak pulse power was studied. The effects of various parameters of PMI on the polymerization were analyzed and compared with that under conventional heating (CH) process. The results were summarized, as compared with that under CH, as follows. The amount of initiator used to reach constant conversion reduced by 50% at the same polymerization time; at the same initiator concentration 0.15 and 0.2 wt.%, the polymerization rate increased by 131% and 163%, respectively. The molecular weight of polymer obtained was 1.1-2.0 times larger than that under CH; at the same irradiation energy, the conversion achieved using a lower pulse power was greater than that using a higher pulse power. There seemed to be a factor of the irradiation energy efficiency; in other words, for the monomer conversion, the irradiation energy of low pulse power had a higher efficiency. The conversion achieved using a 3.5 μs pulse width was almost the same as that using a 1.5 μs pulse width. The results indicated that PMI had a significant non-thermal effect on the emulsion polymerization of MMA so as to effectively enhance the polymerization rate. The glass transition temperature (T_g), the polydispersity index (PDI) and the regularity of the polymer obtained using two processes were similar, indicating that the physical properties and microstructure of the polymer were not modified by the use of microwaves.