Miscibility studies on blends of poly(phenylene oxide)/brominated polystyrene by viscometry

The viscosity behavior of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO), brominated polystyrene (PBrS) and their blends at several compositions (25/75, 50/50, 75/25, 85/15) has been studied. The miscibility of this polymer system was investigated on the basis of the sign of the criteria Δb, α, ΔK, μ, and Δ[η] determined by viscosity. These investigations indicate that PPO/PBrS is miscible at the compositions of (75/25), (85/15) and completely immiscible at the compositions of (25/75), (50/50) in chloroform at 20 °C. Results from viscometry match very well those of DSC results cited in the literature.     

The assessment of miscibility and morphology of poly(ε-caprolactone) and poly(para-chlorostyrene) blends

The miscibility and morphology of poly(ε-caprolactone) (PCl) and poly(para-chlorostyrene) (PpClS) blend were investigated by using thermal analysis, morphological analysis, viscometry, and the study of melting point depression. A single glass transition temperature was observed by differential scanning calorimetry (DSC) for PCl/PpClS blends in the whole compositional range (0/100, 25/75, 50/50, 62.5/37.5, 75/25, 90/10). Morphology of the polymers and their blends was studied by scanning electron microscopy (SEM). The Fourier transform infrared spectra of the samples were obtained by spectrometer. Up to 12 cm⁻¹ shifts in carbonyl stretching band of PCl was detected in the spectra of PpClS rich blends. The viscosity of PCl, PpClS and their blends has also been studied to investigate the miscibility according the miscibility criteria Δb, and Δ[η]. Using this data, the interaction parameters α and μ, based on the Chee and Sun et al. approaches were determined. These criteria indicated that the blend is miscible in all proportions up to 90% of PCl content in the blends. The melting point depression of PCl in the blends was examined to obtain the interaction parameter, χ₁₂ for this system. The parameter, χ₁₂ was found to be composition dependent. Negative values of the obtained interaction parameter also support the miscibility of this system up to the 90% PCl in the blend.     

Miscibility and interactions of polystyrene/polyolefine and polystyrene/poly(n-alkyl methacrylate) mixtures in dilute xylene solutions

The miscibility and intermolecular interactions between polystyrene (PS) and poly(ethylene-co-propylene) (EPC), as well as between PS and long-chain poly(alkyl methacrylates) (PAMA), namely, poly(dodecyl methacrylate) (PDDMA) and poly(octadecyl methacrylate) (PODMA), in dilute xylene solutions at 30 °C were studied. Investigated polymers are widely used as rheology modifiers, i.e. viscosity index improvers and pour point depressants for lubricating mineral oils. The specific and reduced viscosities of two- and three-component polymer solutions as well as intrinsic viscosities and Huggins’ parameter values were determined as functions of the polymer mixture composition and overall polymer concentration. The reduced viscosity was found to be linearly dependent on the overall polymer concentration. The observed viscosities of polymer mixtures were intermediate to those of the mixture constituents; the values decrease in the order: EPC > PS > PAMA. The specific viscosities of all the polymer mixtures obtained as the experimental results and calculated applying the Catsiff-Hewett and Krigbaum-Wall theoretical equations were considered. Since all the polymer/polymer pairs showed the negative viscometric interaction parameter values (Δb₁₂ < 0), the PS/EPC and EPC/PAMA mixtures were found to be immiscible. The observed repulsive molecular interactions originate from the differences in polymer composition and molar masses. This conclusion was supported by calculations employing the group contribution approach of Coleman, Graf and Painter. The calculated values of interaction parameters for (co)polymer blends, Λ₁₂, were 5.47, 6.42 and 13.1 J cm⁻³ for PS/PDDMA, PS/PODMA and PS/EPC, respectively.     

Effect of mixed solvent on solution properties and gelation behavior of poly(vinyl alcohol)

In this work, the static and dynamic light scattering measurements were used to investigate the solution properties and the aging effects on PVA/DMSO/water ternary system in dilute region at 25 °C. It was found that the phase separation and aggregate behavior occurs rapidly and obviously when DMSO mole fraction (X₁) in the solvent mixture is between 0.2 and 0.33, especially at 0.25. In this solvent composition range, a broad peak which indicates phase separation and chain aggregation can be observed from static light scattering measurement. However, when DMSO mole fraction is increased to 0.37, no such peak is present. For this ternary system, the gelation mechanism and the relationship between the phase separation behavior and the gelation of the formed physical gels were also investigated through the gelation kinetic analyses in the dilute and semi-dilute region. It is concluded that the cononsolvency effect in the dilute solution is not the sole origin that affects the phase separation, aggregation, and gelation behavior for the ternary system in a higher polymer concentration range. The hydrodynamic factors such as the higher viscosity and slower polymer chain diffusion that are resulted from higher polymer concentration should be also considered.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Thermal and photochemical stability of poly(vinyl alcohol)/modified lignin blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (24, 48, and 96 h) and analyzed by thermogravimetry (TG), differential scanning calorimetry (DSC), infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy, and scanning electron microscopy (SEM). PVA films show a loss of thermal stability due to irradiation. PVA/KLD reveals greater thermal stability than PVA and an increase in thermal stability after irradiation. These results suggest that the incorporation of KLD into PVA provides a gain in thermal and photochemical stability. FTIR, ¹H NMR, DSC, and TG results obtained for the blends suggest that intermolecular interactions between PVA and KLD chains are present. SEM micrographs revealed blend miscibility for a KLD blend content of up to 15 wt%, as observed at magnification of 1000 times.     

Miscibility and enzymatic degradation studies of poly(ε-caprolactone)/poly(propylene succinate) blends

In the present study the miscibility behaviour and the biodegradability of poly(ε-caprolactone)/poly(propylene succinate) (PCL/PPSu) blends were investigated. Both of these aliphatic polyesters were laboratory synthesized. For the polymer characterization DSC, ¹H NMR, WAXD and molecular weight measurements were performed. Blends of the polymers with compositions 90/10, 80/20, 70/30 and 60/40 w/w were prepared by solution-casting. DSC analysis of the prepared blends indicated only a very limited miscibility in the melt phase since the polymer-polymer interaction parameter χ₁₂ was −0.11. In the case of crystallized specimens two distinct phases existed in all studied compositions as it was found by SEM micrographs and the particle size distribution of PPSu dispersed phase increased with increasing PPSu content. Enzymatic hydrolysis for several days of the prepared blends was performed using Rhizopus delemar lipase at pH 7.2 and 30 °C. SEM micrographs of thin film surfaces revealed that hydrolysis affected mainly the PPSu polymer as well as the amorphous phase of PCL. For all polymer blends an increase of the melting temperatures and the heat of fusions was recorded after the hydrolysis. The biodegradation rates as expressed in terms of weight loss were faster for the blends with higher PPSu content. Finally, a simple theoretical kinetic model was developed to describe the enzymatic hydrolysis of the blends and the Michaelis-Menten parameters were estimated.     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

Preparation of poly(vinyl pivalate) microspheres by dispersion polymerization in an ionic liquid and saponification for the preparation of poly(vinyl alcohol) with high syndiotacticity

We report here a successful free-radical dispersion polymerization of vinyl pivalate (VPi) in an ionic liquid, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([bmim][TFSI]) using poly(vinyl pyrrolidone) (PVP) as a stabilizer. Morphological analysis by FE-SEM revealed that poly(vinyl pivalate) (PVPi) obtained from dispersion polymerizations were in the form of spherical particles. Micron-sized, PVPi particles with a number-average molecular weight (M_n) of 166,400 g/mol could be obtained using 5% stabilizer (w/w to monomer) at 65 °C for 20 h. The effects of varying concentration of stabilizer, initiator and monomer upon polymer yield, molecular weight, and morphology of PVPi were also investigated. Analogous polymerizations in dimethyl sulfoxide (DMSO) and bulk served as references. In addition, the preparation of poly(vinyl alcohol) (PVA) by saponification of the resultant PVPi was described.     

Miscibility and hydrolytic degradation in alkaline solution of poly(l-lactide) and poly(p-vinyl phenol) blends

Poly(l-lactide) (PLLA) was melt-blended with poly(p-vinyl phenol) (PVPh) using a two-roll mill, and the miscibility between PLLA and PVPh and degradation of the blend films were investigated. It was found that PLLA/PVPh blend has miscibility in the amorphous state because only single T_g was observed in the DSC and DMA measurements. The T_g of the PLLA/PVPh blend could be controlled in the temperature range from 55 °C to 117 °C by changing the PVPh weight fraction. In alkaline solution, degradation rate of PLLA/PVPh blends was faster than that of neat PLLA because PVPh could dissolve in alkaline solution. The surface morphology of degraded PLLA and PLLA/PVPh blend were observed by SEM. The surface morphology of degraded PLLA/PVPh blend was finer than that of PLLA. Young's modulus of PLLA/PVPh blend increased with increasing PVPh content. Yield stress of PLLA/PVPh blends whose PVPh content was less than 30 wt% kept the level of about 55 MPa and that of PLLA/PVPh blend whose PVPh content was 40 wt% is much lower than that of neat PLLA.     

The evaluation of miscibility of blends of poly(ether imide) (Ultem1000) and a copolyester of bisphenol-A with terephthalic and isophthalic acid (ArdelD-100) by viscosimetry

The intermolecular interactions and miscibility behavior between poly(ether imide) (Ultem^®1000) and a copolyester of bisphenol-A with a mixture of terephthalic and isophthalic acid (Ardel^®D-100) in compositions of 100/0, 80/20, 60/40, 40/60, 20/80 and 0/100 have been investigated in dilute solutions in chloroform. An Ubbelohde-type home-made viscometer was used to determine the specific viscosities of the blends in a constant temperature bath. Several viscosity interaction parameters used as the criteria of miscibility were determined from viscosity measurements. The parameters suggested that Ultem^®1000 and Ardel^®D-100 were miscible. The miscibility of the polymers was confirmed by the results of differential scanning calorimetry measurements.     

Characterisation of Hyaluronic Acid Blends Modified by Poly(N-Vinylpyrrolidone)

The viscosity behaviour and physical properties of blends containing hyaluronic acid (HA) and poly(N-vinylpyrrolidone) (PVP) were studied by the viscometric technique, steady shear tests, tensile tests and infrared spectroscopy. Viscometric and rheological measurements were carried out using blends of HA/PVP with different HA weight fractions (0, 0.2, 0.5, 0.8 and 1). The polymer films and HA/PVP blend films were prepared using the solution casting method. The study of HA blends by viscometry showed that HA/PVP was miscible with the exception of the blend with high HA content. HA and its blends showed a shear-thinning flow behaviour. The non-Newtonian indices (n) of HA/PVP blends were calculated by the Ostwald–de Waele equation, indicating a shear-thinning effect in which pseudoplasticity increased with increasing HA contents. Mechanical properties, such as tensile strength and elongation at the break, were higher for HA/PVP films with w_HA = 0.5 compared to those with higher HA contents. The elongation at the break of HA/PVP blend films displayed a pronounced increase compared to HA films. Moreover, infrared analysis confirmed the existence of interactions between HA and PVP. The blending of HA with PVP generated films with elasticity and better properties than homopolymer films.     

Synthesis and characterization of biodegradable aliphatic copolyesters with poly(ethylene oxide) soft segments

A series of multiblock poly(ether-ester)s based on poly(butylene succinate) (PBS) as the hard segments and hydrophilic poly(ethylene oxide) (PEO) as the soft segments was synthesized with the aim of developing degradable polymers which could combine the mechanical properties of high performance elastomers with those of flexible plastics. The aliphatic poly(ether-ester)s were synthesized by the catalyzed two-step transesterification reaction of dimethyl succinate, 1,4-butanediol and α,ω-hydroxyl terminated poly(ethylene oxide) (PEO, = 1000 g/mol) in bulk. The content of soft PEO segments in the polymer chains was varied from about 10 to 50 mass%. The effect of the introduction of the soft PEO segments on the structure, thermal and physical properties, as well as on the biodegradation properties was investigated. The composition and structure of these aliphatic segmented copolyesters were determined by ¹H NMR spectroscopy. The molecular weights of the polyesters were verified by gel permeation chromatography (GPC), as well as by viscometry of dilute solutions and polymer melts. The thermal properties were investigated using differential scanning calorimetry (DSC). The degree of crystallinity was determined by means of DSC and wide-angle X-ray scattering. A depression of melting temperature and a reduction of crystallinity of the hard segments with increasing content of PEO segments were observed. Biodegradation of the synthesized copolyesters, estimated in enzymatic degradation tests in phosphate buffer solution with Candida rugosa lipase at 37 °C was compared with hydrolytic degradation in the buffer solution. The weight losses of the samples were in the range from 2 to 10 mass%. GPC analysis confirmed that there were significant changes in molecular weight of copolyesters with higher content of PEO segments, up to 40% of initial values. This leads to conclusion that degradation mechanism of the poly(ether-ester)s based on PEO segments occurs through bulk degradation in addition to surface erosion.     

Interaction of collagen and poly(vinyl pyrrolidone) in blends

The interaction between collagen and poly(vinyl pyrrolidone) (PVP) in blends has been studied by viscometry, differential scanning calorimetry (DSC) and by Fourier transform infrared spectroscopy (FTIR). It was found that the amide A and amide I bands position in FTIR spectra of collagen were shifted after blending with PVP to higher wavenumbers. DSC measurements showed different melting temperature, glass transition temperature and enthalpy for the blends and for the single components. Viscosity measurements showed interaction between collagen and PVP also in a dilute water solution.The results have shown, that the interactions between collagen and PVP exist due to the strong interactions between the synthetic and biological component, mainly by hydrogen bonds. These interactions caused that collagen and PVP are miscible at molecular level. The blending of collagen with PVP may give the possibility of producing new materials for potential biomedical applications.     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.     

Miscibility studies on the blends of collagen/chitosan by dilute solution viscometry

The viscosity behavior of collagen, chitosan and their blends at several compositions (2/8, 4/6, 5/5, 6/4, 8/2) has been studied. The miscibility of this polymer system was investigated on the basis of the sign of the criteria ΔB, Δb, Δ[η], α and β determined by dilute solution viscosity. These investigations indicate that collagen/chitosan is miscible at any composition in HAc at 25 °C. According to the “memory effect”, we can conclude that collagen/chitosan is also miscible in the solid state.     

Kinetic study of the thermal decomposition of poly(vinyl alcohol)/kraft lignin derivative blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride, was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (Hg lamp, 96 h) and analyzed by thermogravimetry (TG) in inert and oxidative atmosphere. Typical multi-step decomposition profiles were obtained. The apparent activation energy (E_a) of the thermal degradation of the samples was computed by the Vyazovkin method. The KLD degradation presented only small intervals of decomposition degree with constant E_a values. PVA and blends showed intervals of up to 50% in decomposition degree with nearly constant E_a, and smaller intervals in which E_a varies drastically. The influences of samples irradiation and of surrounding gas in TG analysis on E_a are also shown.     

Effect of temperature on the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions

In this work the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions were measured at 283.1–313.1 K. The expansion factor of polymer chain was calculated by use of the intrinsic viscosities data. The thermodynamic parameters of polymer solution (the entropy of dilution parameter, the heat of dilution parameter, theta temperature, polymer–solvent interaction parameter and second osmotic virial coefficient) were evaluated by temperature dependence of polymer chain expansion factor. The obtained thermodynamic parameters indicate that quality of water was decreased for solutions of poly(ethylene oxide), poly(vinyl pyrrolidone) and poly(ethylene oxide)/poly(vinyl pyrrolidone) blends by increasing temperature. Compatibility of poly(ethylene oxide)/poly(vinyl pyrrolidone) blends were explained in terms of difference between experimental and ideal intrinsic viscosity and solvent–polymer interaction parameter. The results indicate that the poly(ethylene glycol)/poly(vinyl pyrrolidone) blends were incompatible.     

Miscibility and thermal stability of poly(vinyl alcohol)/chitosan mixtures

The miscibility and the thermal behaviour of chitosan acetate (ChA) with poly(vinyl alcohol) (PVA) have been investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). Chitosan is blended with poly(vinyl alcohol) in acetic acid solution and this solution is cast to prepare the blend film. From thermal curves the thermal transitions: T_g, T_m and characteristic temperatures of decomposition: T_di, T_max have been determined and compared. The influence of the degree of PVA hydrolysis on the thermal properties of blend systems has been discussed.Based upon the observation on the DSC analysis, the melting point of PVA is decreased when the amount of ChA in the blend film is increased. Though some broadening of the transition curves could be noticed (DSC, TGA and DMA), the obtained results suggest that in the solid ChA/PVA blends the components are poorly miscible. Only PVA sample with relatively low DH = 88% and hence low degree of crystallinity shows partial miscibility with ChA of relatively low molecular weight.     

Conductivity and thermal behavior of proton conducting polymer electrolyte based on poly (N-vinyl pyrrolidone)

The polymer electrolytes based on poly N-vinyl pyrrolidone (PVP) and ammonium thiocyanate (NH₄SCN) with different compositions have been prepared by solution casting technique. The amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The shift in T_g values and the melting temperatures of the PVP-NH₄SCN electrolytes shown by DSC thermo-grams indicate an interaction between the polymer and the salt. The dependence of T_g and conductivity upon salt concentration have been discussed. The conductivity analysis shows that the 20 mol% ammonium thiocyanate doped polymer electrolyte exhibit high ionic conductivity and it has been found to be 1.7 × 10⁻⁴ S cm⁻¹, at room temperature. The conductivity values follow the Arrhenius equation and the activation energy for 20 mol% ammonium thiocyanate doped polymer electrolyte has been found to be 0.52 eV.