Simultaneous determination of bromide and nitrate in contaminated waters by ion chromatography using amperometry and absorbance detectors

This study describes a new ion chromatography method using a low-capacity anion exchange column with amperometric and absorbance detection for rapid and simultaneous determination of Br⁻ and NO₃⁻ in contaminated waters where one of these ions is present in excess compared to other. The use of two detectors overcomes the problem of baseline separation for Br⁻ and NO₃⁻ for accurate quantification, which was commonly encountered when using a low-capacity anion exchange column and suppressed conductivity detection mode. The method achieved accurate quantification of these two ions without requirement of baseline separation. The accuracy of 2.8% for NO₃⁻ was determined using a quality control sample obtained from UN GEMS/Water PE Study No. 6. The detection limits for Br⁻ and NO₃⁻ were 20 and 6 μg l⁻¹ (25 μl sample), respectively. Linearity of these two ions was over three orders of magnitude with a correlation coefficient >0.998. The influence of potential interfering ions was also studied followed by the determination of Br⁻ and NO₃⁻ in seawater, unsaturated zone water, soil extract and groundwater.     

Studies on elution conditions for the determination of anions by supressed ion-interaction chromatography using a graphitized carbon column

A new method has been developed for ion-interaction chromatography with suppressed conductivity detection and a new graphitized carbon packing, which is sintered from carbonic material at a high temperature. Combinations of various eluting agents, tetrabutylammonium hydroxide (TBA) and acetonitrile have been investigated to optimize the separation of eight common anions (F⁻, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, SO₄²⁻, HPO₄²⁻ and I⁻). Calibration curves were linear from 0.5 to 10 μg/ml for F⁻, from 1.0 to 20 μg/ml for Cl⁻, NO₂⁻ and NO₃⁻, from 2.5 to 50 μg/ml for Br⁻ and SO₄²⁻ and from 5.0 to 100 μg/ml for HPO₄²⁻ and I⁻ with a correlation coefficient (r) of 0.999 or better. The relative standard deviations (R.S.D.s) of peak areas were between 0.2 and 0.9% for 10 repeated measurements. The application of this newly developed method was demonstrated by the determination of chloride, bromide and sulfate in pharmaceutical compounds using the direct injection method. The analytical results were within ±2% (relative) of the theoretical value, and thus in good agreement with the theoretical value for each sample.     

Ion chromatography of organic-rich natural waters from peatlands: I. Cl, NO2, Br, NO3, HPO4, SO4 and oxalate

Organic-rich natural waters from peat bogs in continental (Switzerland) and maritime (Shetland Islands, Scotland) areas were analysed for Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻, SO₄²⁻ and oxalate using ion chromatography. These anions can be determined simultaneously in the surface and pore water samples from the continental bogs using a 250-μl injection loop. Using this loop, the detection limits were ca. 5 ng/g for the monovalent anions and SO₄²⁻ and 10 ng/g for HPO₄²⁻ and oxalate. An organics-removal cartridge (Dionex OnGuard P) was used to remove humic materials. These cartridges did not significantly affect the measured concentrations of anions in blind standards. Analyses of deionized water treated with these cartridges are not significantly different from those for untreated deionized water. For the maritime bogs, the relatively high concentrations of Cl⁻ (more than 100μ/g in many samples) and SO₄²⁻ (up to 50 μg/g) require two separate determinations for complete analyses. A 10-μl injection loop was used to determine Cl⁻, Br⁻ and SO₄²⁻. A 250-μl injection loop was used to measure NO₂⁻, NO₃⁻, HPO ₄²⁻ and oxalate. In each instance a Dionex OnGuard P cartridge was used to remove humic materials. In addition, a chloride-removal cartridge (Dionex OnGuard AG) was used to remove Cl⁻ when the larger injection loop was used. This cartridge has no significant effect on the measurement of HPO_4-²⁻ at concentrations of 20 ng/g. In each of the bog water chromatograms there were usually a number of unknown peaks. These are probably due mainly to organic anions.     

A novel homocystine-agarose adsorbent for separation and preconcentration of nickel in table salt and baking soda using factorial design optimization of the experimental conditions

Homocystine was for the first time, chemically linked to a highly cross-linked agarose support (Novarose) to be employed as a chelating adsorbent for preconcentration and AAS determination of nickel in table salt and baking soda. Nickel is quantitatively adsorbed on a small column packed with 0.25 ml of the adsorbent, in a pH range of 5.5–6.5 and simply eluted with 5 ml of a 1 mol l⁻¹ hydrochloric acid solution.

A factorial design was used for optimization of the effects of five different variables on the recovery of nickel. The results indicated that the factors of flow rate and column length, and the interactions between pH and sample volume are significant.

In the optimized conditions, the column could tolerate salt concentrations up to 0.5 mol l⁻¹ and sample volumes beyond 500 ml. Matrix ions of Mg²⁺ and Ca²⁺, with a concentration of 200 mg l⁻¹, and potentially interfering ions of Cd²⁺, Cu²⁺, Zn²⁺ and Mn²⁺, with a concentration of 10 mg l⁻¹, did not have significant effect on the analyte's signal. Preconcentration factors up to 100 and a detection limit of 0.49 μg l⁻¹, corresponding to an enrichment volume of 500 ml, were obtained for the determination of the analyte by flame AAS. Application of the method to the determination of natural and spiked nickel in table salt and baking soda solutions resulted in quantitative recoveries. Direct ETAAS determination of nickel in the same samples was not possible because of a high background observed.     

Determination of iron(III) with salicylic acid by the fluorescence quenching method

The spectrofluorimetric determination of Fe³⁺ using salicylic acid as an emission reagent has been investigated by measuring the decrease of fluorescence intensity of salicylic acid due to the complexation of Fe³⁺–salicylic acid. An emission peak of salicylic acid, which is decreased linearly by addition of Fe³⁺, occurs at 409 nm in aqueous solution with excitation at 299 nm. The determination of the ferric ion is in the range 1×10⁻⁶–10×10⁻⁶ M Fe³⁺ (0.0558–0.558 μg/ml) and the detection limit is 5×10⁻⁸ M. The quenching effect of Fe³⁺ on the fluorescence intensity of salicylic acid may be considered on the basis of complexation between salicylic acid and Fe³⁺. The effects of foreign ions were investigated.     

Silicon determination by inductively coupled plasma atomic emission spectrometry after generation of volatile silicon tetrafluoride

A method for the determination of silicon by inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. The procedure is based on a discontinuous generation of volatile silicon tetrafluoride in concentrated sulphuric acid medium after injecting 125 μl of 0.1%, w/v sodium fluoride solution into 100 μl of the sample. The gaseous silicon tetrafluoride is fed directly into the ICP torch by a flow of 250 ml min⁻¹ Ar carrier gas. The calibration curve was linear up to at least 100 μg ml⁻¹ of Si(IV) and the absolute detection limit was 9.8 ng working with a solution volume of 100 μl. The relative standard deviation for six measurements of 10 μg ml⁻¹ of Si(IV) was 2.32%. The method was applied to the determination of silicon in water and iron ores.     

Manipulation of separation selectivity of inorganic anions in electrostatic ion chromatography by the use of mixed cationic–zwitterionic micelles as the column coating solution

This paper describes an electrostatic ion chromatographic system in which the separation selectivity for inorganic anions, especially for sulfate and phosphate, could be manipulated by altering the molar ratio of the zwitterionic and cationic surfactants in the column coating solution used to prepare the stationary phase. The zwitterionic surfactant used for this study was 3-(N,N-dimethyltetradecylammonio)propanesulfonate (Zwittergent-3-14) and the cationic surfactant was tetradecyltrimethylammonium (TTA). Using a reversed-phase C₁₈ column (250×4.6 mm I.D.) coated with 10/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the stationary phase and either NaHCO₃ or Na₂CO₃ aqueous solution as the eluent, together with suppressed conductivity detection, baseline separation of seven model inorganic anions was obtained. The elution order for those anions was found to be F⁻4²⁻−4²⁻2⁻−3⁻. Under the same conditions but using 1/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the column coating solution, the elution order for these model ions was F⁻4²⁻4²⁻−2⁻−3⁻. The early elution of phosphate and sulfate is a unique attribute of this system. Detection limits for F⁻, HPO₄²⁻, Cl⁻, SO₄²⁻, NO₂⁻, Br⁻ and NO₃⁻ (S/N=3, sample injection volume 100 μl) were 0.11, 0.12, 0.12, 0.18, 0.49, 0.49, 0.52 μM, respectively.     

Continuous flow system for lead determination by faas in spirituous beverages with solid phase extraction and on-line copper removal

A continuous flow system for the determination of lead in home made spirituous beverages was developed. The determination was based on the formation of a neutral chelate of the element with ammonium pyrrolidine dithiocarbamate, its adsorption onto a minicolumn packed with sodium faujasite type Y synthetic zeolite, followed by elution with methyl isobutyl ketone and determination by flame atomic absorption spectrometry. Ethanol and copper interfere strongly in the determination and therefore, must be separated prior to the analysis. Copper is removed by precipitation with rubeanic acid, while ethanol is eliminated by rotaevaporation. Sample solutions containing Pb²⁺ in the concentration range from 5 to 120 μg l⁻¹ at pH 2.5 could be analyzed, by using a preconcentration time of 3 min. Preconcentration factors from 80 to 140 were achieved for a sample volume of 6 ml and the detection limit varied from 1.4 to 3.5 μg l⁻¹, depending on the matrix composition. The relative standard deviations for 60 μg l⁻¹ Pb was 3.2% (n = 10) and the recovery of spikes (20, 40, 60 and 80 μg l⁻¹) added to the samples was estimated within 92–105% range, suggesting that lead can be quantitatively determined in such samples. Determining lead in several samples by an alternative technique further checked the accuracy. Finally, the concentrations of Pb²⁺ determined in 28 samples of Venezuelan spirituous beverages were in 12.6–370.0 μg l⁻¹ range, depending on the fermenting material based on different mixtures of agave, raw sugar cane and white sugar.     

Fast flow-injection fluorimetric determination of amiloride by using a solid sensing zone

A rapid and simple flow-through solid phase spectrofluorimetric system is described in this paper for the determination of the diuretic amiloride in physiological fluid (serum) and pharmaceuticals. The sensor was developed in conjunction with a monochannel flow-injection analysis system with fluorimetric transduction. Amiloride was transitorily retained on cationic exchanger gel Sephadex SP-C25 placed in the detection area into the cell. The determination is carried out without any derivatization reaction, by measuring directly the intrinsic fluorescence of the analyte and using the peak height as analytical signal. The wavelengths of excitation and emission were 291 and 419 nm, respectively. Amiloride could be determined in the concentration ranges of 10–600 and 4–250 μg l⁻¹ at a sampling rate of 24 and 30 h⁻¹, respectively with detection limits of 0.92 and 0.33 μg l⁻¹ for 100, and 600 μl of sample volume injected, respectively. The relative standard deviations for ten independent determinations were better than 0.65%. The method was satisfactorily applied to the determination of amiloride in spiked biological fluids (serum) and pharmaceutical preparations without any pretreatment of the samples.     

Electrothermal atomic absorption spectrometric determination of lead in high-purity reagents with flow-injection on-line microcolumn preconcentration and separation using a macrocycle immobilized silica gel sorbent

A fully automated procedure for the determination of ng l⁻¹ amounts of lead has been developed using flow injection (FI) online column preconcentration coupled with electrothermal atomic absorption spectrometry (ETAAS). The proposed FI manifold and its operation make possible the introduction of the total eluate volume into the graphite atomizer, avoiding the necessity for optimization of subsampling the eluate. The interference of other heavy metal ions due to competition for active sites of the sorbent is overcome using a highly selective macrocycle immobilized on silica gel (Pb-02). Lead is adsorbed on a microcolumn (50 μl) packed with Pb-02, and after washing the column with dilute nitric acid, air is introduced to remove all solution from the column and connecting tubing. The sorbed analyte is then eluted quantitatively into the graphite tube atomizer, preheated to 100°C, with 36 μl of ETDA solution (0.035 mol l⁻¹, pH 10.5), propelled by air in order to minimize dispersion. The collection efficiency was 77% and with a sample loading flow rate of 3 ml min⁻¹ and a 60 s preconcentration time, the enhancement factor was 77 and the throughput was 17 samples per hour. The relative standard deviation (n = 10) at the 300 ng l⁻¹ level was 2.7%, and the detection limit (3σ) was 0.4 ng l⁻¹. No interference from heavy metals was observed, but ions of Ba²⁺, Sr²⁺ and K⁺ were found to interfere when the concentration ratios of interferent to lead exceeded values of 2000, 20 000 and 200 000, respectively. Quantitative recovery of lead was achieved from sodium, magnesium, aluminum, lanthanum and heavy metal salt solutions. The high selectivity and sensitivity, combined with extremely low blank values, make the proposed technique particularly attractive for the analysis of high-purity reagents, semiconductors and other high-purity materials. Results are presented for the determination of lead in some high-purity reagents.     

Use of silica gel chemically modified with zirconium phosphate for preconcentration and determination of lead and copper by flame atomic absorption spectrometry

An analytical method using silica gel chemically modified with zirconium (IV) phosphate for preconcentration of lead and copper, in a column system, and their sequential determination by flame atomic absorption spectrometry (FAAS), was developed. Sample solutions are passed through a glass column packed with 100 mg of the sorbent material, at pH 4.5, and lead and copper are eluted with 1.0 mol l⁻¹ HNO₃ at a flow rate of 2.0 ml min⁻¹. The extraction of copper is affected by Fe(II), Mn(II), Zn(II), Ni(II) and Co(II) while only Fe(II) interferes in the lead determination. These interferences may be overcome with an appropriate addition of a KI or NaF solution. An enrichment factor of 30 was obtained for both metals. While the limits of detection (3σ) were 6.1 and 1.1 μg l⁻¹, for Pb and Cu, respectively, the limits of determination were 16.7 and 3.3 μg l⁻¹. The precision expressed as relative standard deviation (R.S.D.) obtained for 3.3 μg l⁻¹ of Cu and 16.7 μg l⁻¹ of Pb were 4.3 and 4.7%, respectively, calculated from ten measurements. The proposed method was evaluated with reference material and was applied for the determination of lead and copper in industrial and river waters.     

An on-line flow-injection microwave-assisted mineralization and a precipitation/dissolution system for the determination of molybdenum in blood serum and whole blood by electrothermal atomic absorption spectrometry

An on-line flow injection (FI) precipitation–dissolution system with microwave-assisted sample digestion has been developed for the electrothermal atomic absorption spectrometry (ETAAS) determination of trace or ultratrace amounts of molybdenum in human blood serum and whole blood samples. After the exposure of the sample to microwave radiation, the on-line precipitation of molybdenum was achieved by the merging-zone of a 0.5-ml plug of sample with a plug of potassium ferrocyanide, which were carried downstream with a solution of 0.5 mol l⁻¹ of HNO₃. The interfering effects of iron and copper were minimized by the introduction of a flow of a 5% (w/v) sodium potassium tartrate (for iron) and 2% (w/v) of thiourea (for copper and zinc) in a 5% (v/v) ammonia and 2% (v/v) ammonium chloride solution previous to the precipitation reaction. The reddish-brown precipitate of molybdenyl ferrocyanide was collected on the walls of a knotted reactor. The precipitate was dissolved with the introduction of 1 ml of a 3.0 mol l⁻¹ NaOH solution and the best performance in terms of detection limit and precision was achieved when a sub-sample of 140 μl was collected in a capillary of a sampling arm assembly, to introduce 20 μl volumes into the atomizer by means of positive displacement with air through a time-based injector. A detection limit (3σ) of 0.1 μg Mo l⁻¹ using an aqueous standard solution was obtained. The method is quantitative and is applied over the range 0.2–20.0 μg Mo l⁻¹. The precision of the method evaluated by ten replicate analyses of aqueous standard solutions containing 0.5 and 1.0 μg Mo l⁻¹ was 2.8 and 3.1% (relative standard deviation, RSD) (for n=5), respectively. Whereas, the precision evaluated by five replicate analysis of a serum and a whole blood sample were 3.3 and 3.8% RSD. An enrichment factor of ca. 3.5 was achieved with the introduction of 0.5 ml aqueous standard solutions at a sample flow rate of 1.0 ml min⁻¹. Recoveries of spiked molybdenum in blood serum and whole blood were in the ranges 96–102 and 94–98%, respectively. The results obtained for two human whole blood certified reference materials were in good agreement with the indicative values.     

Specific adsorption of halogen anions on hydrous γ-Al2O3

The paper reports results of a study on the specific adsorption of F⁻, Cl⁻, Br⁻, I⁻, ClO₃⁻, BrO₃⁻, IO₃⁻ and IO₄⁻ on hydrous γ-Al₂O₃. The isotherms of the anion adsorption and the adsorption dependencies on pH and the ionic strength of the solution have been determined under the equilibrium conditions. According to the degree of affinity to γ-Al₂O₃, the anions can be ordered as: I⁻3⁻−−3⁻3⁻4⁻−. It has been established that the sorption of IO₄⁻ and F⁻ involves the formation of surface complexes in the inner co-ordination sphere, whereas that of Cl⁻, Br⁻, I⁻, ClO₃⁻, BrO₃⁻ and IO₃⁻ takes place through formation of ion pair complexes in the outer co-ordination sphere. In the dynamic system, the exchange isoplanes and elution curves have been determined for selected anions on columns filled with Al₂O₃. It has been shown that γ-Al₂O₃ can be used for isolation and concentration of IO₃⁻ from natural waters in order to decrease the limit of the ions determination to 2 μg l⁻¹. Using differential pulse voltammetry (DPV), after isolation and concentration on γ-Al₂O₃, the content of iodates has been determined in mineral, marine and tap water doped with these ions.     

Simultaneous derivative spectrophotometric determination of thorium and uranium in a micellar medium

Derivative photometric methods for trace analysis of Th(IV) and UO₂(II), and their simultaneous determination in mixtures using 5,8-dihydroxy-1,4-naphthoquinone in a micellar medium are reported. Molar absorptivity and Sandell's sensitivity of 1:2 Th(IV) and 1:1 UO₂(II) complexes at their λ_max, 614.5 nm and 637.0 nm are, 1.19 × 10⁴ 1/mol/cm and 1.12 × 10⁴ 1/mol/cm and 1.95 × 10⁻² μg/cm² and 2.13 × 10⁻² μg/cm² μg/cm², respectively. Calibration graph is linear over the range 9.28 × 10⁻²−18.56 μg/ml of Th(IV) and 9.52 × 10⁻²−19.04 μg/ml of UO₂(II). Though presence of Th(IV) and UO₂(II) causes interference in each others determination, 9.28 × 10⁻¹−9.28 μg/ml Th(IV) and 9.52 × 10⁻¹−9.52 μg/ml UO₂(II) when present together, can be simultaneously determined using derivative spectra.     

Simultaneous determination of arsenic, antimony and selenium by gas-phase diode array molecular absorption spectrometry, after preconcentration in a cryogenic trap

This paper describes a method for the simultaneous determination of As(III), Sb(III) and Se(IV) by combining hydride generation and gas phase molecular absorption spectrometry. A system for continuous hydride generation has been designed and developed, based on the use of a double process of gas-liquid separation, and optimal compromise operation conditions for the three compounds have been found. After generation, the hydrides are collected in a liquid nitrogen cryogenic trap, and then evaporated and driven to the flow cell of a diode array spectrophotometer, in which the transient signals over the 190–250 nm wavelength interval are measured. Under the recommended conditions (sample flow: 35 ml min⁻¹, 0.5 M HCl; reductor flow: 4 ml min⁻¹ of 4% NaBH₄, solution) linear response ranges above 50 μg 1⁻¹ for As(III), 30 μg 1⁻¹ for Sb(III) and 200 μg 1⁻¹ for Se(IV) are obtained with detection limits of 22 μg 1⁻¹, 15 μg 1⁻¹ and 65 μg 1⁻¹, respectively. Multiwavelength linear regression equations were used for the simultaneous determination of the three elements in different synthetic samples, with good precision and accuracy and to study simultaneously the interference from different chemical species for the three compounds. Results were similar to those obtained by other techniques using hydride generation.     

Capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples from hydrothermal springs and fumaroles

A new application of capillary electrophoresis for measuring major and trace anions in thermal water and condensed-steam samples is presented. Ten fluid samples were collected from hydrothermal springs and fumaroles located in a volcanic zone of Deception Island, Antarctica. Anion separation was achieved in less than 6 min using indirect UV detection at 254 nm with a negative power supply (−15 kV). The electrolyte consisted of 4.7 mM sodium chromate, 4.0 mM electroosmotic flow modifier (OFM) hydroxide, 10 mM 2-(N-cyclohexylamino)ethanesulfonic acid and 0.1 mM calcium gluconate (pH 9.1). Major anions (Cl⁻, SO₄², PO₄H²⁻, and CO₃H⁻) were measured using hydrostatic injection (10 cm for 30 s) at 25°C. Trace amounts of anions (F⁻, Br⁻, and NO₃⁻) were better determined by electromigration injection (4 kV, 10 s) at 15°C. Good reproducibility of the migration times (<0.72% RSD), a satisfactory linear response and accuracy as well as acceptable detection limits were successfully obtained.     

Determination of mercury in saliva with a flow-injection system

A simple, fast and reliable method, with a low detection limit, has been developed for the determination of total mercury in saliva samples. The method uses a brominating reagent, followed by on-line addition of KMnO₄ at room temperature to convert organically bound mercury to inorganic mercury ions, and determines mercury by flow-injection cold-vapour atomic absorption spectrometry. Using the method described, complete recoveries of five mercury compounds from saliva were attained. Results obtained on real samples using the new method were comparable to that obtained using the established method with batch system. The detection limit of this method, based on three standard deviations of the blank, is 0.05 μg l⁻¹ Hg in a saliva sample of 500 μl. A sample throughput of 80 measurements per hour is possible with the method. The calibration curves are linear up to 20 μg l⁻¹ and the dynamic range extends to 40 μg l⁻¹ Hg. At a concentration of 1μg l⁻¹ mercury in saliva, the relative standard deviation is about 2% for 11 replicates; a total volume of 0.5 ml saliva is required for three replicates.     

End-column electrochemical detection for inorganic and organic species in high-voltage capillary electrophoresis

The electronics and construction for an end-column ultramicroelectrode (3–10 μm) detection system that permits the use of medium-sized capillaries (25 μm I.D.) without appreciable effects from the potential field at the end of the capillary. Normal peak-to-peak noise over 10 s was 0.01–0.1 pA. The background noise observed for a 200 × μm carbon-fiber electrode placed either 180 μm within a 25-μm capillary or at a point 500 μm away from the capillary was essentially the same. A study of detector response as a function of the position of the electrode has shown that accurate location of the electrode is important for sensitive and reproducible detection. These studies also showed that differences between the density of the electrolyte existing the capillary and the electrolyte in the detection cell could cause anomalous electrode response depending on the location of the electrode relative to the end of the capillary. Application of a carbon fiber or an Hg film electrode gave detection limits (twice the peak-to-peak noise over 10 s) of 2 · 10⁻⁸ mol/l for Pb²⁺, 1 · 10^{− 5} mol/l for NO₂⁻ and 5 · 10⁻¹⁰ mol/l for catechol.     

Determination of aluminium and manganese in human scalp hair by electrothermal atomic absorption spectrometry using slurry sampling

Methods for the determination of aluminium and manganese in human scalp hair samples by electrothermal atomic absorption spectrometry using the slurry sampling technique were developed. Palladium and magnesium nitrate were used as chemical modifiers. Hair samples were pulverized using a zirconia vibrational mill ball, and were prepared as aqueous slurries. Determinations can be performed in the linear ranges of 1.9–150 μg l⁻¹ Al³⁺ and 0.03–10.0 μg l⁻¹ Mn²⁺. Limits of detection of 0.9 mg kg⁻¹ and 27.6 μg kg⁻¹ were obtained for aluminium and manganese, respectively. The analytical recoveries were between 99.6 and 101.8% for aluminium and in the 98.3–101.3% range for manganese. The repeatability of the methods (n=11), slurry preparation procedure and ETAAS measurement, was 16.0 and 7.9% for aluminium and manganese, respectively. The methods were finally applied to the aluminium and manganese determination in 25 scalp hair samples from healthy adults. The levels for aluminium were between 8.21 and 74.08 mg kg⁻¹, while concentrations between 0.03 and 1.20 mg kg⁻¹ were found for manganese.     

Evaluation of ammonia as diluent for serum sample preparation and determination of selenium by graphite furnace atomic absorption spectrometry

A method for the determination of total selenium in serum samples by graphite furnace atomic absorption spectrometry was evaluated. The method involved direct introduction of 1:5 diluted serum samples (1% v/v NH₄OH+0.05% w/v Triton X-100^®) into transversely heated graphite tubes, and the use of 10 μg Pd+3 μg Mg(NO₃)₂ as chemical modifier. Optimization of the modifier mass and the atomization temperature was conducted by simultaneously varying such parameters and evaluating both the integrated absorbance and the peak height/peak area ratio. The latter allowed the selection of compromise conditions rendering good sensitivity and adequate analyte peak profiles. A characteristic mass of 49 pg and a detection limit (3s) of 6 μg 1⁻¹ Se, corresponding to 30 μg l⁻¹ Se in the serum sample, were obtained. The analyte addition technique was used for calibration. The accuracy was assessed by the determination of total selenium in Seronorm™ Trace Elements Serum Batch 116 (Nycomed Pharma AS). The method was applied for the determination of total selenium in ten serum samples taken from individuals with no known physical affection. The selenium concentration ranged between 79 and 147 μg l⁻¹, with a mean value of 114±22 μg l⁻¹.