Identification and quantification of the volatile constituents in Cnidium monnieri using supercritical fluid extraction followed by GC‐MS

The volatile components of Cnidium monnieri were obtained by supercritical fluid extraction (SFE) and analyzed by GC‐MS (identification and determination of metabolites). The compounds were identified according to their retention times and mass spectra. The effects of different parameters, such as extraction pressure, temperature, dynamic extraction time, flow rate of CO₂, on the SFE of C. monnieri extracts were investigated. A total of 14 compounds of SFE extracts were identified. Osthole (69.52%), bornyl acetate (10.03%), α‐pinene (4.71%), and imperatorin (2.42%) were the major compounds identified in C. monnieri SFE extracts. The quantitation of osthole and imperatorin were then accomplished. The linear calibration ranges were all 5–1000 μg/mL for osthole and imperatorin by GC‐MS analysis. The recovery of osthole and imperatorin were in the range 96.5–101.8%. The LODs for osthole and imperatorin were 1.0 and 0.6 μg/mL, respectively.     

The application of gas chromatography/atmospheric pressure chemical ionisation time‐of‐flight mass spectrometry to impurity identification in Pharmaceutical Development

Accurate mass measurement (used to determine elemental formulae) is an essential tool for impurity identification in pharmaceutical development for process understanding. Accurate mass liquid chromatography/mass spectrometry (LC/MS) is used widely for these types of analyses; however, there are still many occasions when gas chromatography (GC)/MS is the appropriate technique. Therefore, the provision of robust technology to provide accurate mass GC/MS (and GC/MS/MS) for this type of activity is essential. In this report we describe the optimisation and application of a newly available atmospheric pressure chemical ionisation (APCI) interface to couple GC to time‐of‐flight (TOF) MS. To fully test the potential of the new interface the APCI source conditions were optimised, using a number of standard compounds, with a variety of structures, as used in synthesis at AstraZeneca. These compounds were subsequently analysed by GC/APCI‐TOF MS. This study was carried out to evaluate the range of compounds that are amenable to analysis using this technique. The range of compounds that can be detected and characterised using the technique was found to be extremely broad and include apolar hydrocarbons such as toluene. Both protonated molecules ([M + H]⁺) and radical cations (M^+.) were observed in the mass spectra produced by APCI, along with additional ion signals such as [M + H + O]⁺. The technique has been successfully applied to the identification of impurities in reaction mixtures from organic synthesis in process development. A typical mass accuracy of 1–2 mm/zunits (m/z 80–500) was achieved allowing the reaction impurities to be identified based on their elemental formulae. These results clearly demonstrate the potential of the technique as a tool for problem solving and process understanding in pharmaceutical development. The reaction mixtures were also analysed by GC/electron ionisation (EI)‐MS and GC/chemical ionisation (CI)‐MS to understand the capability of GC/APCI‐MS relative to these two firmly established techniques. Copyright © 2010 John Wiley & Sons, Ltd.     

Searching for anthropogenic contaminants in human breast adipose tissues using gas chromatography‐time‐of‐flight mass spectrometry

The potential of gas chromatography‐time‐of‐flight mass spectrometry (GC‐TOF MS) for screening anthropogenic organic contaminants in human breast adipose tissues has been investigated. Initially a target screening was performed for a list of 125 compounds which included persistent halogen pollutants [organochlorine (OC) pesticides, polychlorinated biphenylss (PCBs), polybrominated diphenyl ethers (PBDEs)], polyaromatic hydrocarbons (PAHs), alkylphenols, and a notable number of pesticides from the different fungicide, herbicide and insecticide families. Searching for target pollutants was done by evaluating the presence of up to five representative ions for every analyte, all measured at accurate mass (20‐mDa mass window). The experimental ion abundance ratios were then compared to those of reference standards for confirmation. Sample treatment consisted of an extraction with hexane and subsequent normal‐phase (NP) High performance liquid chromatography (HPLC) or SPE cleanup. The fat‐free LC fractions were then investigated by GC‐TOF MS. Full‐spectral acquisition and accurate mass data generated by GC‐TOF MS also allowed the investigation of nontarget compounds using appropriate processing software to manage MS data. Identification was initially based on library fit using commercial nominal mass libraries. This was followed by comparing the experimental accurate masses of the most relevant ions with the theoretical exact masses with calculations made using the elemental composition calculator included in the software. The application of both target and nontarget approaches to around 40 real samples allowed the detection and confirmation of several target pollutants including p,p′‐DDE, hexachlorobenzene (HCB), and some polychlorinated biphenyls (PCBs) and polyaromatic hydrocarbons (PAHs). Several nontarget compounds that could be considered anthropogenic pollutants were also detected. These included 3,5‐di‐tert‐butyl‐4‐hydroxy‐toluene (BHT) and its metabolite 3,5‐di‐tert‐butyl‐4‐hydroxybenzaldehyde (BHT‐CHO), dibenzylamine, N‐butyl benzenesulfonamide (N‐BBSA), some naphthalene‐related compounds and several PCBs isomers not included in the target list. As some of the compounds detected are xenoestrogens, the methodology developed in this paper could be useful in human breast cancer research. Copyright © 2008 John Wiley & Sons, Ltd.     

GC‐MS of amaryllidaceous galanthamine‐type alkaloids

Galanthamine‐type alkaloids produced by plants of the Amaryllidaceae family are potent acetylcholinesterase inhibitors. One of them, galanthamine, has been marketed as a hydrobromide salt for the treatment of Alzheimer's disease. In the present work, gas chromatography with electron impact mass spectrometry (GC‐EIMS) fragmentation of 12 reference compounds isolated from various amaryllidaceous plants and identified by spectroscopic methods (1D and 2D nuclear magnetic resonance, circular dichroism, high‐resolution MS (HRMS) and EIMS) was studied by tandem mass spectrometry (GC‐MS/MS) and accurate mass measurements (GC‐HRMS). The studied compounds showed good peak shape and efficient GC separation with a GC‐MS fragmentation pattern similar to that obtained by direct insertion probe. With the exception of galanthamine‐N‐oxide and N‐formylnorgalanthamine, the galanthamine‐type compounds showed abundant [M]^+. and [M‐H]⁺ ions. A typical fragmentation pattern was also observed, depending on the substituents of the skeleton. Based on the fragmentation pathways of reference compounds, three other galanthamine‐type alkaloids, including 3‐O‐(2′‐butenoyl)sanguinine, which possesses a previously unelucidated structure, were identified in Leucojum aestivum ssp. pulchelum, a species endemic to the Balearic islands. GC‐MS can be successfully applied to Amaryllidaceae plant samples in the routine screening for potentially new or known bioactive molecules, chemotaxonomy, biodiversity and identification of impurities in pharmaceutical substances. Copyright © 2012 John Wiley & Sons, Ltd.     

Supercritical fluid extraction of the volatile oil from Santolina chamaecyparissus

Supercritical fluid extraction (SFE) of the volatile oil from Santolina chamaecyparissus L. flower heads was performed under different conditions of pressure, temperature, mean particle size and CO₂ flow rate. This oil was compared with the essential oil isolated by hydrodistillation (HD). The SFE volatile and essential oils were analysed by GC and GC‐MS. The range of the main volatile components obtained with HD and SFE were, respectively: 1,8‐cineole (25–30% and 7–48%), camphor (7–9% and 8–14%), borneol (7–8% and 2–11%), terpinen‐4‐ol (6–7% and 1–4%), terpinolene (1–4% and 1–7%) and isobornyl acetate (1–2% and 1–11%). The chemical composition of the extracts was greatly influenced by the conditions of pressure and temperature used. In fact, it was possible to enrich the sesquiterpene fraction by increasing the pressure from 8 to 9 MPa, while changing the temperature from 40 to 50°C at 90 bar enriched of the volatiles in n‐alkanes.     

Enrichment of the thymoquinone content in volatile oil from Satureja montana using supercritical fluid extraction

Supercritical fluid extraction (SFE) of the volatile oil from Satureja montana L. was performed under different conditions of pressure (90 and 100 bar), temperature (40 and 50°C), mean particle sizes (0.4, 0.6 and 0.8 mm) and CO₂ flow rate (0.8, 1.1 and 1.3 kg/h) to understand the influence of these parameters on the composition and yield of this oil. The results were compared with those obtained for the essential oil isolated by hydrodistillation (HD). The volatile and the essential oil were analysed by GC and GC‐MS. The main compounds are carvacrol (52.2–62.0% for HD vs. 41.7–64.5% for SFE), thymol (8.6–11.0% for HD vs. 6.0–11.3% for SFE), p‐cymene (6.9–12.8% for HD vs. 6.0–17.8% for SFE), γ‐terpinene (6.4–9.4% for HD vs. 2.3–6.0% for SFE) and β‐bisabolene (2.0–2.7% for HD vs. 2.2–3.5% for SFE). The major difference between SFE and HD was the relative amount of thymoquinone, an oxygenated monoterpene with important biological activities, which can be ten‐fold higher in volatile oil (1.6–3.0 for SFE vs. 0.2% for HD). The morphology of the glandular trichomes of S. montana and the effect of the grinding process on them was also evaluated by SEM.     

Comparison of three chromatographic techniques for the detection of mitragynine and other indole and oxindole alkaloids in Mitragyna speciosa (kratom) plants

Leaves of the Southeast Asian plant Mitragyna speciosa are used to suppress pain and mitigate opioid withdrawal syndromes. The potential threat of abuse and ready availability of this uncontrolled psychoactive plant have led to the need for improved analytical techniques for the detection of the major active components, mitragynine and 7‐hydroxymitragynine. Three independent chromatographic methods coupled to two detection systems, GC with MS, supercritical fluid chromatography with diode array detection, and HPLC with MS and diode array detection, were compared for the analysis of mitragynine and other indole and oxindole alkaloids in M. speciosa plants. The indole alkaloids included two sets of diastereoisomers: (i) paynantheine and 3‐isopaynantheine and (ii) mitragynine, speciogynine, and speciociliatine. Two oxindole alkaloid diastereoisomers, corynoxine and corynoxine B, were also studied. The HPLC and supercritical fluid chromatography methods successfully resolved the major components with slightly different elution orders. The GC method was less satisfactory because it was unable to resolve mitragynine and speciociliatine. This separation was difficult by GC with a liquid stationary phase because these diastereoisomers differ only in the orientation of an interior hydrogen atom. The observed lack of resolution of the indole alkaloid diastereoisomers coupled with the likeness of the mass and tandem mass spectra, calls into question proposed GC methods for the analysis of mitragynine based on solely GC with MS separation and identification.     

Identification of substances migrating from plastic baby bottles using a combination of low‐resolution and high‐resolution mass spectrometric analysers coupled to gas and liquid chromatography

This work presents a strategy for elucidation of unknown migrants from plastic food contact materials (baby bottles) using a combination of analytical techniques in an untargeted approach. First, gas chromatography (GC) coupled to mass spectrometry (MS) in electron ionisation mode was used to identify migrants through spectral library matching. When no acceptable match was obtained, a second analysis by GC‐(electron ionisation) high resolution mass spectrometry time of flight (TOF) was applied to obtain accurate mass fragmentation spectra and isotopic patterns. Databases were then searched to find a possible elemental composition for the unknown compounds. Finally, a GC hybrid quadrupole‐TOF‐MS with an atmospheric pressure chemical ionisation source was used to obtain the molecular ion or the protonated molecule. Accurate mass data also provided additional information on the fragmentation behaviour as two acquisition functions with different collision energies were available (MS^E approach). In the low‐energy function, limited fragmentation took place, whereas for the high‐energy function, fragmentation was enhanced. For less volatile unknowns, ultra‐high pressure liquid chromatography‐quadrupole‐TOF‐MS was additionally applied. Using a home‐made database containing common migrating compounds and plastic additives, tentative identification was made for several positive findings based on accurate mass of the (de)protonated molecule, product ion fragments and characteristic isotopic ions. Six illustrative examples are shown to demonstrate the modus operandi and the difficulties encountered during identification. The combination of these techniques was proven to be a powerful tool for the elucidation of unknown migrating compounds from plastic baby bottles. Copyright © 2015 John Wiley & Sons, Ltd.     

Application of supercritical fluid extraction coupled with counter–current chromatography for extraction and online isolation of unstable chemical components from Rosa damascena

Supercritical fluid extraction (SFE) coupled with high‐speed counter‐current chromatography (HSCCC) was successfully used for the extraction and online isolation of the unstable compounds from Rosa damascene in a single extraction and separation operation in two stages. The solvent systems of SFE/HSCCC were optimized with the help of multiexponential function model. At the first stage, the upper phase of the solvent system of n‐butanol–tert‐butyl methyl ether–acetonitrile–0.1% aqueous TFA (1.7:1.0:0.8:4.0, v/v/v/v) was used as both the SFE entrainer and the HSCCC stationary phase, and the target compounds were eluted with the corresponding lower phase to separate the hydrophobic compounds. At the second stage, the upper phase of the solvent system of n‐hexane–ethyl acetate–methanol–water (3.2:1.0:2.8:2.6, v/v/v/v) was used as both the SFE entrainer and the HSCCC stationary phase, followed by elution with the corresponding lower phase to separate the moderate hydrophobic compounds. Six compounds including formononetin, delphinidin, cyaniding, 5,6,4′‐trihydroxy‐7,8‐dimethoxy flavone, 5,3′‐dihydroxy‐7,8‐dimethoxy flavone, and 5‐hydroxy‐6,7,8,3′,4′‐pentamethoxy flavone were successfully separated in one extraction–separation operation within 300 min. The targeted compounds were identified by MS and NMR spectroscopy. This research has opened up great prospects for industrial application of SFE/HSCCC to the extraction and separation of unstable compounds.     

Isolation of volatiles from Nigella sativa seeds using microwave‐assisted extraction: effect of whole extracts on canine and murine CYP1A

The volatile components of Nigella sativa seeds were isolated using microwave‐assisted extraction (MAE) and identified using gas chromatography. Further investigations were carried out to demonstrate the effects of whole extracts on canine (dog) and murine (rat) cytochrome P450 1A (CYP1A). The optimal extraction conditions of MAE were as follows: 25 mL of water, medium level of microwave oven power and 10 min of extraction time. A total of 32 compounds were identified under the conditions using GC‐FID and GC‐MS. Thymoquinone (38.23%), p‐cymene (28.61%), 4‐isopropyl‐9‐methoxy‐1‐methyl‐1‐cyclohexene (5.74%), longifolene (5.33%), α‐thujene (3.88) and carvacol (2.31%) were the main compounds emitted from N. sativa seeds. Various extracts including pure compounds, essential oil, nonpolar partition, relatively high‐polar/nonpolar partition, and polar partition extracts effectively inhibited the reaction of ethoxyresorufin O‐de‐ethylation, which is specified for CYP1A activity both in dog and rat. This in vitro data should be heeded as a signal of possible in vivo interactions. The use of human liver preparations would considerably strengthen the practical impact of the data generated from this study. Copyright © 2013 John Wiley & Sons, Ltd.     

Bioactivity‐based ultra‐performance liquid chromatography‐coupled quadrupole time‐of‐flight mass spectrometry for NF‐κB inhibitors identification in Chinese Medicinal Preparation Bufei Granule

Traditional Chinese medicine (TCM) preparations have become effective treatments for many diseases. However, their active ingredients are still uncertain and difficult to identify. In this study, we propose a strategy that integrates ultra‐performance liquid chromatography/quadrupole‐time‐of‐flight mass spectrometry (UPLC/Q‐TOF‐MS) and bioactive (NF‐κB inhibitor) luciferase reporter assay systems for the rapid determination of various anti‐inflammatory compounds of TCM preparations. In this way, Bufei Granule (BFG), a TCM preparation used for the clinical therapy of asthma, was analyzed by the two ways of component identification and activity detection. Potential anti‐inflammatory constituents were screened by NF‐κB activity assay systems and simultaneously identified according to the mass spectrometry data. Three structural types of NF‐κB inhibitors (caffeic acid derivatives, flavonoids and Pentacyclic triterpenes) were characterized. Further cytokine detection confirmed the anti‐inflammatory effects of the potential NF‐κB inhibitors. Compared with conventional chromatographic separation and inhibitory activity detection, integrating UPLC/Q‐TOF‐MS identification and virtual validation was more convenient and more reliable. This strategy clearly demonstrates that MS data‐based fingerprinting is a meaningful tool not only in identifying constituents in complex matrix but also in directly screening for powerful trace ingredients in TCM preparations. Copyright © 2016 John Wiley & Sons, Ltd.     

Characterization of secondary volatile profiles in Nigella sativa seeds from two different origins using accelerated solvent extraction and gas chromatography-mass spectrometry

The extraction and identification of bioactive compounds from herbs is of great interest. In this study, accelerated solvent extraction (ASE) technique was used to analyze the secondary volatile profiles in Nigella sativa seeds obtained from two different origins, Egypt and Bangladesh. The main extraction parameters, including extraction temperature, pressure and static extraction time, were investigated and optimized. Identification and quantification of the major constituents in nonpolar extracts (hexane) were achieved by means of GC‐FID/GC‐MS analysis with external standards. The two seeds showed a similar variety of chemical composition; however, the secondary volatiles profile of Bangladesh seed was higher than that of the Egyptian seed. A total of 25 compounds were identified from the ASE extract under the following optimum extraction conditions: 100°C, 1500 psi and 5 min, for extraction temperature, pressure and static time, respectively. The proposed technique can be used for the characterization of N. sativa varieties or cultivars. Copyright © 2012 John Wiley & Sons, Ltd.     

Composition and antioxidant activity of Thymus vulgaris volatiles: Comparison between supercritical fluid extraction and hydrodistillation

Supercritical fluid extraction (SFE) of the volatile oil from Thymus vulgaris L. aerial flowering parts was performed under different conditions of pressure, temperature, mean particle size and CO₂ flow rate and the correspondent yield and composition were compared with those of the essential oil isolated by hydrodistillation (HD). Both the oils were analyzed by GC and GC‐MS and 52 components were identified. The main volatile components obtained were p‐cymene (10.0–42.6% for SFE and 28.9–34.8% for HD), γ‐terpinene (0.8–6.9% for SFE and 5.1–7.0% for HD), linalool (2.3–5.3% for SFE and 2.8–3.1% for HD), thymol (19.5–40.8% for SFE and 35.4–41.6% for HD), and carvacrol (1.4–3.1% for SFE and 2.6–3.1% for HD). The main difference was found to be the relative percentage of thymoquinone (not found in the essential oil) and carvacryl methyl ether (1.0–1.2% for HD versus t?0.4 for SFE) which can explain the higher antioxidant activity, assessed by Rancimat test, of the SFE volatiles when compared with HD. Thymoquinone is considered a strong antioxidant compound.     

Rapid separation and identification of major constituents in Pseudolarix kaempferi by ultra‐performance liquid chromatography coupled with electrospray and quadrupole time‐of‐flight tandem mass spectrometry

A rapid and reliable method based on ultra‐performance liquid chromatography (UPLC) coupled with photodiode‐array detection (PDA) and electrospray ionization quadrupole time‐of‐flight tandem mass spectrometry (ESI‐Q‐TOF‐MS/MS) has been developed for separation and identification of major constituents in extracts of root bark of Pseudolarix kaempferi Gordon (PKG). Identification of the constituents was carried out by interpretation of their retention times, UV absorption spectra, MS and MS/MS spectra, as well as the data provided by authentic standards and literatures. A total of 20 components were separated in only 8.0 min on a small particle size C₁₈ column (1.7 µm). These components included nine diterpene acids, seven glycosides and four triterpenoids, among which pseudolaric acid C‐O‐β‐D‐glucopyranoside and pseudolaric acid C₂‐O‐β‐D‐glucopyranoside were separated and identified for the first time in this study. Furthermore, the fragmentation patterns of the three types of compounds were elucidated for the first time. This established UPLC‐PDA/Q‐TOF‐MS/MS method is reliable and effective for the separation and identification of the 20 compounds and will be useful for quality control of the crude materials of Pseudolarix kaempferi Gordon and their related preparations. Copyright © 2009 John Wiley & Sons, Ltd.     

CE‐MS analysis of heroin and its basic impurities using a charged polymer‐protected gold nanoparticle‐coated capillary

The first application of charged polymer‐protected gold nanoparticles (Au NPs) as semi‐permanent capillary coating in CE‐MS was presented. Poly(diallyldimethylammonium chloride) (PDDA) was the only reducing and stabilizing agent for Au NPs preparation. Stable and repeatable coating with good tolerance to 0.1 M HCl, methanol, and ACN was obtained via a simple rinsing procedure. Au NPs enhanced the coating stability toward flushing by methanol, improved the run‐to‐run and capillary‐to‐capillary repeatabilities, and improved the separation efficiency of heroin and its basic impurities for tracing geographical origins of illicit samples. Baseline resolution of eight heroin‐related alkaloids was achieved on the PDDA‐protected Au NPs‐coated capillary under the optimum conditions: 120 mM ammonium acetate (pH 5.2) with addition of 13% methanol, separation temperature 20°C, applied voltage ?20 kV, and capillary effective length 60.0 cm. CE‐MS analysis with run‐to‐run RSDs (n=5) of migration time in the range of 0.43–0.62% and RSDs (n=5) of peak area in the range of 1.49–4.68% was obtained. The established CE‐MS method would offer sensitive detection and confident identification of heroin and related compounds and provide an alternative to LC‐MS and GC‐MS for illicit drug control.     

Combination of supercritical fluid extraction with counter‐current chromatography to isolate anthocyanidins from the petals of Chaenomeles sinensis based on mathematical calculations

Supercritical fluid extraction (SFE) coupled with high‐speed counter‐current chromatography (HSCCC) was successfully used for the extraction and on‐line isolation of the anthocyanidins from the petals of Chaenomeles sinensis in two stages. The SFE parameters were optimized by an orthogonal test, and the solvent systems of SFE and HSCCC were calculated and optimized with the help of a multiexponential function model. In the first stage, the lower phase of the solvent system of n‐butanol/tert‐butyl methyl ether/acetonitrile/0.1% aqueous TFA (0.715:1.0:0.134:1.592, v/v/v/v) was used as both the SFE modifier and the HSCCC stationary phase, after extraction, the extractants were pumped into HSCCC column, and then eluted with the corresponding upper phase to isolate the moderately hydrophobic compounds. In the second stage, the upper phase of the solvent system of n‐butanol/ethyl acetate/acetonitrile/0.1% aqueous TFA (1.348:1.0:0.605:2.156, v/v/v/v) was used as both the SFE modifier and the HSCCC stationary phase, followed by elution with the corresponding lower phase to separate the hydrophobic compounds. With the help of two‐stage SFE/HSCCC, six compounds including delphinidin‐3‐O‐glucoside (Dp3G), cyanidin‐3‐O‐glucoside (Cy3G), peonidin‐3‐O‐glucoside (Pn3G), delphinidin (Dp), peonidin (Pn), and malvidin (Mv) were successfully separated within 300 min. The targeted compounds were identified by UV spectrophotometry, MS, and NMR spectroscopy. This research has opened up great prospects for the industrial application of SFE–HSCCC for the automatic extraction and separation of unstable compounds.     

An introduction to hybrid ion trap/time‐of‐flight mass spectrometry coupled with liquid chromatography applied to drug metabolism studies

Metabolism studies play an important role at various stages of drug discovery and development. Liquid chromatography combined with mass spectrometry (LC/MS) has become a most powerful and widely used analytical tool for identifying drug metabolites. The suitability of different types of mass spectrometers for metabolite profiling differs widely, and therefore, the data quality and reliability of the results also depend on which instrumentation is used. As one of the latest LC/MS instrumentation designs, hybrid ion trap/time‐of‐flight MS coupled with LC (LC‐IT‐TOF‐MS) has successfully integrated ease of operation, compatibility with LC flow rates and data‐dependent MSⁿ with high mass accuracy and mass resolving power. The MSⁿ and accurate mass capabilities are routinely utilized to rapidly confirm the identification of expected metabolites or to elucidate the structures of uncommon or unexpected metabolites. These features make the LC‐IT‐TOF‐MS a very powerful analytical tool for metabolite identification. This paper begins with a brief introduction to some basic principles and main properties of a hybrid IT‐TOF instrument. Then, a general workflow for metabolite profiling using LC‐IT‐TOF‐MS, starting from sample collection and preparation to final identification of the metabolite structures, is discussed in detail. The data extraction and mining techniques to find and confirm metabolites are discussed and illustrated with some examples. This paper is directed to readers with no prior experience with LC‐IT‐TOF‐MS and will provide a broad understanding of the development and utility of this instrument for drug metabolism studies. Copyright © 2012 John Wiley & Sons, Ltd.     

Strategy for rapid screening of antioxidant and anti‐inflammatory active ingredients in Gynura procumbens (Lour.) Merr. based on UHPLC–Q‐TOF–MS/MS and characteristic ion filtration

Gynura procumbens (Lour.) Merr. is traditionally used as a raw material for making dumplings or steamed stuffed buns, and its fresh leaves are boiled with water for tea. Herein, we established an ultra‐high–performance liquid chromatography–quadrupole time‐of‐flight mass spectrometry (UHPLC–Q‐TOF–MS/MS) combined with characteristic ion filtration (CIF) strategy to rapidly screen active ingredients with antioxidant and anti‐inflammatory properties in G. procumbens. This strategy involved screening the active part of G. procumbens using antioxidation and anti‐inflammatory activity assays; discovering the active compounds by speculating on the active site's chemical composition by UHPLC–Q‐TOF–MS/MS plus CIF; and verifying the active compounds' activities. The ethyl acetate extract (EEAF) of G. procumbens was the major active site. Eighty‐one compounds were identified from the EEAF using UHPLC–Q‐TOF–MS/MS plus CIF. Furthermore, polyphenols such as cynarine, isochlorogenic acids A and isochlorogenic acids C have excellent antioxidizing and anti‐inflammatory activities. This study provides a practical strategy for rapid in vitro screening of the antioxidizing and anti‐inflammatory activities of traditional vegetables and herbs and identification of active ingredients.     

Atmospheric pressure gas chromatography coupled to quadrupole‐time of flight mass spectrometry as a tool for identification of volatile migrants from autoadhesive labels used for direct food contact

Pressure‐sensitive adhesives (PSA) are used to manufacture labels that are applied directly on the food. These adhesives could contain not only intentionally added compounds (IAS) to the adhesive formula but also non‐intentionally added substances (NIAS), due to the impurities from the raw materials used, decomposition of the initial components or from chemical interactions between them. These compounds could migrate to the food and contaminate it. In this study, gas chromatography coupled with mass spectrometry (GC‐MS/Q) and atmospheric pressure gas chromatography coupled to a quadrupole hyphenated to a time of flight mass spectrometer (APGC‐MS/Q‐TOF) have been used for identification of unknown compounds and NIAS coming from a PSA. Seven compounds were identified by GC‐MS/Q, and other eight compounds remained initially unknown. The structure of these eight new compounds was elucidated by working with the spectra obtained by APGC‐MS/Q‐TOF. Finally, two different migration studies were carried out. The first one with Tenax as solid food simulant in contact with the paper label containing the adhesive and the second one with isooctane filled in a natural pork intestine where the label containing the adhesive was applied on the external side. The results are shown and discussed. Copyright © 2014 John Wiley & Sons, Ltd.